ftgmac100/ftmac100: Move the Faraday drivers

Move the Faraday driver into drivers/net/ethernet/faraday/ and
make the necessary Kconfig and Makefile changes.

CC: "Po-Yu Chuang" <ratbert@faraday-tech.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>

drivers/net/Kconfig

@@ -922,15 +922,6 @@ config XILINX_EMACLITE
 	help
 	  This driver supports the 10/100 Ethernet Lite from Xilinx.
 
-config FTMAC100
-	tristate "Faraday FTMAC100 10/100 Ethernet support"
-	depends on ARM
-	select MII
-	help
-	  This driver supports the FTMAC100 10/100 Ethernet controller
-	  from Faraday. It is used on Faraday A320, Andes AG101 and some
-	  other ARM/NDS32 SoC's.
-
 config LANTIQ_ETOP
 	tristate "Lantiq SoC ETOP driver"
 	depends on SOC_TYPE_XWAY
@@ -1286,15 +1277,6 @@ config PCH_GBE
 	  ML7223 is companion chip for Intel Atom E6xx series.
 	  ML7223 is completely compatible for Intel EG20T PCH.
 
-config FTGMAC100
-	tristate "Faraday FTGMAC100 Gigabit Ethernet support"
-	depends on ARM
-	select PHYLIB
-	help
-	  This driver supports the FTGMAC100 Gigabit Ethernet controller
-	  from Faraday. It is used on Faraday A369, Andes AG102 and some
-	  other ARM/NDS32 SoC's.
-
 endif # NETDEV_1000
 
 #

drivers/net/Makefile

@@ -79,8 +79,6 @@ ifeq ($(CONFIG_FEC_MPC52xx_MDIO),y)
 	obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx_phy.o
 endif
 obj-$(CONFIG_FORCEDETH) += forcedeth.o
-obj-$(CONFIG_FTGMAC100) += ftgmac100.o
-obj-$(CONFIG_FTMAC100) += ftmac100.o
 
 obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o

drivers/net/ethernet/Kconfig

@@ -20,6 +20,7 @@ source "drivers/net/ethernet/chelsio/Kconfig"
 source "drivers/net/ethernet/cisco/Kconfig"
 source "drivers/net/ethernet/emulex/Kconfig"
 source "drivers/net/ethernet/neterion/Kconfig"
+source "drivers/net/ethernet/faraday/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
 source "drivers/net/ethernet/i825xx/Kconfig"

drivers/net/ethernet/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
 obj-$(CONFIG_NET_VENDOR_CISCO) += cisco/
 obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
 obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
+obj-$(CONFIG_NET_VENDOR_FARADAY) += faraday/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
 obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/

drivers/net/ethernet/faraday/Kconfig

+#
+# Faraday device configuration
+#
+
+config NET_VENDOR_FARADAY
+	bool "Faraday devices"
+	depends on ARM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Faraday cards. If you say Y, you will be asked for
+	  your specific card in the following questions.
+
+if NET_VENDOR_FARADAY
+
+config FTMAC100
+	tristate "Faraday FTMAC100 10/100 Ethernet support"
+	depends on ARM
+	select MII
+	---help---
+	  This driver supports the FTMAC100 10/100 Ethernet controller
+	  from Faraday. It is used on Faraday A320, Andes AG101 and some
+	  other ARM/NDS32 SoC's.
+
+config FTGMAC100
+	tristate "Faraday FTGMAC100 Gigabit Ethernet support"
+	depends on ARM
+	select PHYLIB
+	---help---
+	  This driver supports the FTGMAC100 Gigabit Ethernet controller
+	  from Faraday. It is used on Faraday A369, Andes AG102 and some
+	  other ARM/NDS32 SoC's.
+
+endif # NET_VENDOR_FARADAY

drivers/net/ethernet/faraday/Makefile

+#
+# Makefile for the Faraday device drivers.
+#
+
+obj-$(CONFIG_FTGMAC100) += ftgmac100.o
+obj-$(CONFIG_FTMAC100) += ftmac100.o