[netdrvr gianfar] use new phy layer

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

drivers/net/Kconfig

@@ -2075,6 +2075,8 @@ config SPIDER_NET
 config GIANFAR
 	tristate "Gianfar Ethernet"
 	depends on 85xx || 83xx
+	select PHYLIB
+	select PHYCONTROL
 	help
 	  This driver supports the Gigabit TSEC on the MPC85xx 
 	  family of chips, and the FEC on the 8540

drivers/net/Makefile

@@ -13,7 +13,7 @@ obj-$(CONFIG_CHELSIO_T1) += chelsio/
 obj-$(CONFIG_BONDING) += bonding/
 obj-$(CONFIG_GIANFAR) += gianfar_driver.o
 
-gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_phy.o
+gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_mii.o
 
 #
 # link order important here

drivers/net/gianfar.h

@@ -17,7 +17,6 @@
  *
  *  Still left to do:
  *      -Add support for module parameters
- *	-Add support for ethtool -s
  *	-Add patch for ethtool phys id
  */
 #ifndef __GIANFAR_H
@@ -37,7 +36,8 @@
 #include <linux/skbuff.h>
 #include <linux/spinlock.h>
 #include <linux/mm.h>
-#include <linux/fsl_devices.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
 
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -48,7 +48,8 @@
 #include <linux/workqueue.h>
 #include <linux/ethtool.h>
 #include <linux/netdevice.h>
-#include "gianfar_phy.h"
+#include <linux/fsl_devices.h>
+#include "gianfar_mii.h"
 
 /* The maximum number of packets to be handled in one call of gfar_poll */
 #define GFAR_DEV_WEIGHT 64
@@ -73,7 +74,7 @@
 #define PHY_INIT_TIMEOUT 100000
 #define GFAR_PHY_CHANGE_TIME 2
 
-#define DEVICE_NAME "%s: Gianfar Ethernet Controller Version 1.1, "
+#define DEVICE_NAME "%s: Gianfar Ethernet Controller Version 1.2, "
 #define DRV_NAME "gfar-enet"
 extern const char gfar_driver_name[];
 extern const char gfar_driver_version[];
@@ -578,12 +579,7 @@ struct gfar {
 	u32	hafdup;		/* 0x.50c - Half Duplex Register */
 	u32	maxfrm;		/* 0x.510 - Maximum Frame Length Register */
 	u8	res18[12];
-	u32	miimcfg;	/* 0x.520 - MII Management Configuration Register */
-	u32	miimcom;	/* 0x.524 - MII Management Command Register */
-	u32	miimadd;	/* 0x.528 - MII Management Address Register */
-	u32	miimcon;	/* 0x.52c - MII Management Control Register */
-	u32	miimstat;	/* 0x.530 - MII Management Status Register */
-	u32	miimind;	/* 0x.534 - MII Management Indicator Register */
+	u8	gfar_mii_regs[24];	/* See gianfar_phy.h */
 	u8	res19[4];
 	u32	ifstat;		/* 0x.53c - Interface Status Register */
 	u32	macstnaddr1;	/* 0x.540 - Station Address Part 1 Register */
@@ -688,9 +684,6 @@ struct gfar_private {
 	struct gfar *regs;	/* Pointer to the GFAR memory mapped Registers */
 	u32 *hash_regs[16];
 	int hash_width;
-	struct gfar *phyregs;
-	struct work_struct tq;
-	struct timer_list phy_info_timer;
 	struct net_device_stats stats; /* linux network statistics */
 	struct gfar_extra_stats extra_stats;
 	spinlock_t lock;
@@ -710,7 +703,8 @@ struct gfar_private {
 	unsigned int interruptError;
 	struct gianfar_platform_data *einfo;
 
-	struct gfar_mii_info *mii_info;
+	struct phy_device *phydev;
+	struct mii_bus *mii_bus;
 	int oldspeed;
 	int oldduplex;
 	int oldlink;
@@ -732,4 +726,12 @@ extern inline void gfar_write(volatile unsigned *addr, u32 val)
 
 extern struct ethtool_ops *gfar_op_array[];
 
+extern irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs);
+extern int startup_gfar(struct net_device *dev);
+extern void stop_gfar(struct net_device *dev);
+extern void gfar_halt(struct net_device *dev);
+extern void gfar_phy_test(struct mii_bus *bus, struct phy_device *phydev,
+		int enable, u32 regnum, u32 read);
+void gfar_setup_stashing(struct net_device *dev);
+
 #endif /* __GIANFAR_H */

drivers/net/gianfar_ethtool.c

@@ -39,17 +39,18 @@
 #include <asm/types.h>
 #include <asm/uaccess.h>
 #include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
 
 #include "gianfar.h"
 
 #define is_power_of_2(x)        ((x) != 0 && (((x) & ((x) - 1)) == 0))
 
-extern int startup_gfar(struct net_device *dev);
-extern void stop_gfar(struct net_device *dev);
-extern void gfar_halt(struct net_device *dev);
 extern void gfar_start(struct net_device *dev);
 extern int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit);
 
+#define GFAR_MAX_COAL_USECS 0xffff
+#define GFAR_MAX_COAL_FRAMES 0xff
 static void gfar_fill_stats(struct net_device *dev, struct ethtool_stats *dummy,
 		     u64 * buf);
 static void gfar_gstrings(struct net_device *dev, u32 stringset, u8 * buf);
@@ -182,38 +183,32 @@ static void gfar_gdrvinfo(struct net_device *dev, struct
 	drvinfo->eedump_len = 0;
 }
 
+
+static int gfar_ssettings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct gfar_private *priv = netdev_priv(dev);
+	struct phy_device *phydev = priv->phydev;
+
+	if (NULL == phydev)
+		return -ENODEV;
+
+	return phy_ethtool_sset(phydev, cmd);
+}
+
+
 /* Return the current settings in the ethtool_cmd structure */
 static int gfar_gsettings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
 	struct gfar_private *priv = netdev_priv(dev);
-	uint gigabit_support = 
-		priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
-			SUPPORTED_1000baseT_Full : 0;
-	uint gigabit_advert = 
-		priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
-			ADVERTISED_1000baseT_Full: 0;
-
-	cmd->supported = (SUPPORTED_10baseT_Half
-			  | SUPPORTED_100baseT_Half
-			  | SUPPORTED_100baseT_Full
-			  | gigabit_support | SUPPORTED_Autoneg);
-
-	/* For now, we always advertise everything */
-	cmd->advertising = (ADVERTISED_10baseT_Half
-			    | ADVERTISED_100baseT_Half
-			    | ADVERTISED_100baseT_Full
-			    | gigabit_advert | ADVERTISED_Autoneg);
-
-	cmd->speed = priv->mii_info->speed;
-	cmd->duplex = priv->mii_info->duplex;
-	cmd->port = PORT_MII;
-	cmd->phy_address = priv->mii_info->mii_id;
-	cmd->transceiver = XCVR_EXTERNAL;
-	cmd->autoneg = AUTONEG_ENABLE;
+	struct phy_device *phydev = priv->phydev;
+
+	if (NULL == phydev)
+		return -ENODEV;
+	
 	cmd->maxtxpkt = priv->txcount;
 	cmd->maxrxpkt = priv->rxcount;
 
-	return 0;
+	return phy_ethtool_gset(phydev, cmd);
 }
 
 /* Return the length of the register structure */
@@ -241,14 +236,14 @@ static unsigned int gfar_usecs2ticks(struct gfar_private *priv, unsigned int use
 	unsigned int count;
 
 	/* The timer is different, depending on the interface speed */
-	switch (priv->mii_info->speed) {
-	case 1000:
+	switch (priv->phydev->speed) {
+	case SPEED_1000:
 		count = GFAR_GBIT_TIME;
 		break;
-	case 100:
+	case SPEED_100:
 		count = GFAR_100_TIME;
 		break;
-	case 10:
+	case SPEED_10:
 	default:
 		count = GFAR_10_TIME;
 		break;
@@ -265,14 +260,14 @@ static unsigned int gfar_ticks2usecs(struct gfar_private *priv, unsigned int tic
 	unsigned int count;
 
 	/* The timer is different, depending on the interface speed */
-	switch (priv->mii_info->speed) {
-	case 1000:
+	switch (priv->phydev->speed) {
+	case SPEED_1000:
 		count = GFAR_GBIT_TIME;
 		break;
-	case 100:
+	case SPEED_100:
 		count = GFAR_100_TIME;
 		break;
-	case 10:
+	case SPEED_10:
 	default:
 		count = GFAR_10_TIME;
 		break;
@@ -292,6 +287,9 @@ static int gfar_gcoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
 	if (!(priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE))
 		return -EOPNOTSUPP;
 
+	if (NULL == priv->phydev)
+		return -ENODEV;
+
 	cvals->rx_coalesce_usecs = gfar_ticks2usecs(priv, priv->rxtime);
 	cvals->rx_max_coalesced_frames = priv->rxcount;
 
@@ -348,6 +346,22 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
 	else
 		priv->rxcoalescing = 1;
 
+	if (NULL == priv->phydev)
+		return -ENODEV;
+
+	/* Check the bounds of the values */
+	if (cvals->rx_coalesce_usecs > GFAR_MAX_COAL_USECS) {
+		pr_info("Coalescing is limited to %d microseconds\n",
+				GFAR_MAX_COAL_USECS);
+		return -EINVAL;
+	}
+
+	if (cvals->rx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) {
+		pr_info("Coalescing is limited to %d frames\n",
+				GFAR_MAX_COAL_FRAMES);
+		return -EINVAL;
+	}
+
 	priv->rxtime = gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs);
 	priv->rxcount = cvals->rx_max_coalesced_frames;
 
@@ -358,6 +372,19 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
 	else
 		priv->txcoalescing = 1;
 
+	/* Check the bounds of the values */
+	if (cvals->tx_coalesce_usecs > GFAR_MAX_COAL_USECS) {
+		pr_info("Coalescing is limited to %d microseconds\n",
+				GFAR_MAX_COAL_USECS);
+		return -EINVAL;
+	}
+
+	if (cvals->tx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) {
+		pr_info("Coalescing is limited to %d frames\n",
+				GFAR_MAX_COAL_FRAMES);
+		return -EINVAL;
+	}
+
 	priv->txtime = gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs);
 	priv->txcount = cvals->tx_max_coalesced_frames;
 
@@ -536,6 +563,7 @@ static void gfar_set_msglevel(struct net_device *dev, uint32_t data)
 
 struct ethtool_ops gfar_ethtool_ops = {
 	.get_settings = gfar_gsettings,
+	.set_settings = gfar_ssettings,
 	.get_drvinfo = gfar_gdrvinfo,
 	.get_regs_len = gfar_reglen,
 	.get_regs = gfar_get_regs,

drivers/net/gianfar_mii.c

+/* 
+ * drivers/net/gianfar_mii.c
+ *
+ * Gianfar Ethernet Driver -- MIIM bus implementation
+ * Provides Bus interface for MIIM regs
+ *
+ * Author: Andy Fleming
+ * Maintainer: Kumar Gala (kumar.gala@freescale.com)
+ *
+ * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <asm/ocp.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+#include "gianfar.h"
+#include "gianfar_mii.h"
+
+/* Write value to the PHY at mii_id at register regnum,
+ * on the bus, waiting until the write is done before returning.
+ * All PHY configuration is done through the TSEC1 MIIM regs */
+int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value)
+{
+	struct gfar_mii *regs = bus->priv;
+
+	/* Set the PHY address and the register address we want to write */
+	gfar_write(&regs->miimadd, (mii_id << 8) | regnum);
+
+	/* Write out the value we want */
+	gfar_write(&regs->miimcon, value);
+
+	/* Wait for the transaction to finish */
+	while (gfar_read(&regs->miimind) & MIIMIND_BUSY)
+		cpu_relax();
+
+	return 0;
+}
+
+/* Read the bus for PHY at addr mii_id, register regnum, and
+ * return the value.  Clears miimcom first.  All PHY
+ * configuration has to be done through the TSEC1 MIIM regs */
+int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+	struct gfar_mii *regs = bus->priv;
+	u16 value;
+
+	/* Set the PHY address and the register address we want to read */
+	gfar_write(&regs->miimadd, (mii_id << 8) | regnum);
+
+	/* Clear miimcom, and then initiate a read */
+	gfar_write(&regs->miimcom, 0);
+	gfar_write(&regs->miimcom, MII_READ_COMMAND);
+
+	/* Wait for the transaction to finish */
+	while (gfar_read(&regs->miimind) & (MIIMIND_NOTVALID | MIIMIND_BUSY))
+		cpu_relax();
+
+	/* Grab the value of the register from miimstat */
+	value = gfar_read(&regs->miimstat);
+
+	return value;
+}
+
+
+/* Reset the MIIM registers, and wait for the bus to free */
+int gfar_mdio_reset(struct mii_bus *bus)
+{
+	struct gfar_mii *regs = bus->priv;
+	unsigned int timeout = PHY_INIT_TIMEOUT;
+
+	spin_lock_bh(&bus->mdio_lock);
+
+	/* Reset the management interface */
+	gfar_write(&regs->miimcfg, MIIMCFG_RESET);
+
+	/* Setup the MII Mgmt clock speed */
+	gfar_write(&regs->miimcfg, MIIMCFG_INIT_VALUE);
+
+	/* Wait until the bus is free */
+	while ((gfar_read(&regs->miimind) & MIIMIND_BUSY) &&
+			timeout--)
+		cpu_relax();
+
+	spin_unlock_bh(&bus->mdio_lock);
+
+	if(timeout <= 0) {
+		printk(KERN_ERR "%s: The MII Bus is stuck!\n",
+				bus->name);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+
+int gfar_mdio_probe(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct gianfar_mdio_data *pdata;
+	struct gfar_mii *regs;
+	struct mii_bus *new_bus;
+	int err = 0;
+
+	if (NULL == dev)
+		return -EINVAL;
+
+	new_bus = kmalloc(sizeof(struct mii_bus), GFP_KERNEL);
+
+	if (NULL == new_bus)
+		return -ENOMEM;
+
+	new_bus->name = "Gianfar MII Bus",
+	new_bus->read = &gfar_mdio_read,
+	new_bus->write = &gfar_mdio_write,
+	new_bus->reset = &gfar_mdio_reset,
+	new_bus->id = pdev->id;
+
+	pdata = (struct gianfar_mdio_data *)pdev->dev.platform_data;
+
+	if (NULL == pdata) {
+		printk(KERN_ERR "gfar mdio %d: Missing platform data!\n", pdev->id);
+		return -ENODEV;
+	}
+
+	/* Set the PHY base address */
+	regs = (struct gfar_mii *) ioremap(pdata->paddr, 
+			sizeof (struct gfar_mii));
+
+	if (NULL == regs) {
+		err = -ENOMEM;
+		goto reg_map_fail;
+	}
+
+	new_bus->priv = regs;
+
+	new_bus->irq = pdata->irq;
+
+	new_bus->dev = dev;
+	dev_set_drvdata(dev, new_bus);
+
+	err = mdiobus_register(new_bus);
+
+	if (0 != err) {
+		printk (KERN_ERR "%s: Cannot register as MDIO bus\n", 
+				new_bus->name);
+		goto bus_register_fail;
+	}
+
+	return 0;
+
+bus_register_fail:
+	iounmap((void *) regs);
+reg_map_fail:
+	kfree(new_bus);
+
+	return err;
+}
+
+
+int gfar_mdio_remove(struct device *dev)
+{
+	struct mii_bus *bus = dev_get_drvdata(dev);
+
+	mdiobus_unregister(bus);
+
+	dev_set_drvdata(dev, NULL);
+
+	iounmap((void *) (&bus->priv));
+	bus->priv = NULL;
+	kfree(bus);
+
+	return 0;
+}
+
+static struct device_driver gianfar_mdio_driver = {
+	.name = "fsl-gianfar_mdio",
+	.bus = &platform_bus_type,
+	.probe = gfar_mdio_probe,
+	.remove = gfar_mdio_remove,
+};
+
+int __init gfar_mdio_init(void)
+{
+	return driver_register(&gianfar_mdio_driver);
+}
+
+void __exit gfar_mdio_exit(void)
+{
+	driver_unregister(&gianfar_mdio_driver);
+}

drivers/net/gianfar_mii.h

+/* 
+ * drivers/net/gianfar_mii.h
+ *
+ * Gianfar Ethernet Driver -- MII Management Bus Implementation
+ * Driver for the MDIO bus controller in the Gianfar register space
+ *
+ * Author: Andy Fleming
+ * Maintainer: Kumar Gala (kumar.gala@freescale.com)
+ *
+ * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __GIANFAR_MII_H
+#define __GIANFAR_MII_H
+
+#define MIIMIND_BUSY            0x00000001
+#define MIIMIND_NOTVALID        0x00000004
+
+#define MII_READ_COMMAND       0x00000001
+
+#define GFAR_SUPPORTED (SUPPORTED_10baseT_Half \
+		| SUPPORTED_100baseT_Half \
+		| SUPPORTED_100baseT_Full \
+		| SUPPORTED_Autoneg \
+		| SUPPORTED_MII)
+
+struct gfar_mii {
+	u32	miimcfg;	/* 0x.520 - MII Management Config Register */
+	u32	miimcom;	/* 0x.524 - MII Management Command Register */
+	u32	miimadd;	/* 0x.528 - MII Management Address Register */
+	u32	miimcon;	/* 0x.52c - MII Management Control Register */
+	u32	miimstat;	/* 0x.530 - MII Management Status Register */
+	u32	miimind;	/* 0x.534 - MII Management Indicator Register */
+};
+
+int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum);
+int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+int __init gfar_mdio_init(void);
+void __exit gfar_mdio_exit(void);
+#endif /* GIANFAR_PHY_H */

drivers/net/gianfar_phy.h

-/* 
- * drivers/net/gianfar_phy.h
- *
- * Gianfar Ethernet Driver -- PHY handling
- * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560
- * Based on 8260_io/fcc_enet.c
- *
- * Author: Andy Fleming
- * Maintainer: Kumar Gala (kumar.gala@freescale.com)
- *
- * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-#ifndef __GIANFAR_PHY_H
-#define __GIANFAR_PHY_H
-
-#define MII_end ((u32)-2)
-#define MII_read ((u32)-1)
-
-#define MIIMIND_BUSY            0x00000001
-#define MIIMIND_NOTVALID        0x00000004
-
-#define GFAR_AN_TIMEOUT         2000
-
-/* 1000BT control (Marvell & BCM54xx at least) */
-#define MII_1000BASETCONTROL			0x09
-#define MII_1000BASETCONTROL_FULLDUPLEXCAP	0x0200
-#define MII_1000BASETCONTROL_HALFDUPLEXCAP	0x0100
-
-/* Cicada Extended Control Register 1 */
-#define MII_CIS8201_EXT_CON1           0x17
-#define MII_CIS8201_EXTCON1_INIT       0x0000
-
-/* Cicada Interrupt Mask Register */
-#define MII_CIS8201_IMASK		0x19
-#define MII_CIS8201_IMASK_IEN		0x8000
-#define MII_CIS8201_IMASK_SPEED	0x4000
-#define MII_CIS8201_IMASK_LINK		0x2000
-#define MII_CIS8201_IMASK_DUPLEX	0x1000
-#define MII_CIS8201_IMASK_MASK		0xf000
-
-/* Cicada Interrupt Status Register */
-#define MII_CIS8201_ISTAT		0x1a
-#define MII_CIS8201_ISTAT_STATUS	0x8000
-#define MII_CIS8201_ISTAT_SPEED	0x4000
-#define MII_CIS8201_ISTAT_LINK		0x2000
-#define MII_CIS8201_ISTAT_DUPLEX	0x1000
-
-/* Cicada Auxiliary Control/Status Register */
-#define MII_CIS8201_AUX_CONSTAT        0x1c
-#define MII_CIS8201_AUXCONSTAT_INIT    0x0004
-#define MII_CIS8201_AUXCONSTAT_DUPLEX  0x0020
-#define MII_CIS8201_AUXCONSTAT_SPEED   0x0018
-#define MII_CIS8201_AUXCONSTAT_GBIT    0x0010
-#define MII_CIS8201_AUXCONSTAT_100     0x0008
-                                                                                
-/* 88E1011 PHY Status Register */
-#define MII_M1011_PHY_SPEC_STATUS		0x11
-#define MII_M1011_PHY_SPEC_STATUS_1000		0x8000
-#define MII_M1011_PHY_SPEC_STATUS_100		0x4000
-#define MII_M1011_PHY_SPEC_STATUS_SPD_MASK	0xc000
-#define MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX	0x2000
-#define MII_M1011_PHY_SPEC_STATUS_RESOLVED	0x0800
-#define MII_M1011_PHY_SPEC_STATUS_LINK		0x0400
-
-#define MII_M1011_IEVENT		0x13
-#define MII_M1011_IEVENT_CLEAR		0x0000
-
-#define MII_M1011_IMASK			0x12
-#define MII_M1011_IMASK_INIT		0x6400
-#define MII_M1011_IMASK_CLEAR		0x0000
-
-#define MII_DM9161_SCR		0x10
-#define MII_DM9161_SCR_INIT	0x0610
-
-/* DM9161 Specified Configuration and Status Register */
-#define MII_DM9161_SCSR	0x11
-#define MII_DM9161_SCSR_100F	0x8000
-#define MII_DM9161_SCSR_100H	0x4000
-#define MII_DM9161_SCSR_10F	0x2000
-#define MII_DM9161_SCSR_10H	0x1000
-
-/* DM9161 Interrupt Register */
-#define MII_DM9161_INTR	0x15
-#define MII_DM9161_INTR_PEND		0x8000
-#define MII_DM9161_INTR_DPLX_MASK	0x0800
-#define MII_DM9161_INTR_SPD_MASK	0x0400
-#define MII_DM9161_INTR_LINK_MASK	0x0200
-#define MII_DM9161_INTR_MASK		0x0100
-#define MII_DM9161_INTR_DPLX_CHANGE	0x0010
-#define MII_DM9161_INTR_SPD_CHANGE	0x0008
-#define MII_DM9161_INTR_LINK_CHANGE	0x0004
-#define MII_DM9161_INTR_INIT 		0x0000
-#define MII_DM9161_INTR_STOP	\
-(MII_DM9161_INTR_DPLX_MASK | MII_DM9161_INTR_SPD_MASK \
- | MII_DM9161_INTR_LINK_MASK | MII_DM9161_INTR_MASK)
-
-/* DM9161 10BT Configuration/Status */
-#define MII_DM9161_10BTCSR	0x12
-#define MII_DM9161_10BTCSR_INIT	0x7800
-
-#define MII_BASIC_FEATURES	(SUPPORTED_10baseT_Half | \
-				 SUPPORTED_10baseT_Full | \
-				 SUPPORTED_100baseT_Half | \
-				 SUPPORTED_100baseT_Full | \
-				 SUPPORTED_Autoneg | \
-				 SUPPORTED_TP | \
-				 SUPPORTED_MII)
-
-#define MII_GBIT_FEATURES	(MII_BASIC_FEATURES | \
-				 SUPPORTED_1000baseT_Half | \
-				 SUPPORTED_1000baseT_Full)
-
-#define MII_READ_COMMAND       0x00000001
-
-#define MII_INTERRUPT_DISABLED 0x0
-#define MII_INTERRUPT_ENABLED 0x1
-/* Taken from mii_if_info and sungem_phy.h */
-struct gfar_mii_info {
-	/* Information about the PHY type */
-	/* And management functions */
-	struct phy_info *phyinfo;
-
-	/* forced speed & duplex (no autoneg)
-	 * partner speed & duplex & pause (autoneg)
-	 */
-	int speed;
-	int duplex;
-	int pause;
-
-	/* The most recently read link state */
-	int link;
-
-	/* Enabled Interrupts */
-	u32 interrupts;
-
-	u32 advertising;
-	int autoneg;
-	int mii_id;
-
-	/* private data pointer */
-	/* For use by PHYs to maintain extra state */
-	void *priv;
-
-	/* Provided by host chip */
-	struct net_device *dev;
-
-	/* A lock to ensure that only one thing can read/write
-	 * the MDIO bus at a time */
-	spinlock_t mdio_lock;
-
-	/* Provided by ethernet driver */
-	int (*mdio_read) (struct net_device *dev, int mii_id, int reg);
-	void (*mdio_write) (struct net_device *dev, int mii_id, int reg, int val);
-};
-
-/* struct phy_info: a structure which defines attributes for a PHY
- *
- * id will contain a number which represents the PHY.  During
- * startup, the driver will poll the PHY to find out what its
- * UID--as defined by registers 2 and 3--is.  The 32-bit result
- * gotten from the PHY will be ANDed with phy_id_mask to
- * discard any bits which may change based on revision numbers
- * unimportant to functionality
- *
- * There are 6 commands which take a gfar_mii_info structure.
- * Each PHY must declare config_aneg, and read_status.
- */
-struct phy_info {
-	u32 phy_id;
-	char *name;
-	unsigned int phy_id_mask;
-	u32 features;
-
-	/* Called to initialize the PHY */
-	int (*init)(struct gfar_mii_info *mii_info);
-
-	/* Called to suspend the PHY for power */
-	int (*suspend)(struct gfar_mii_info *mii_info);
-
-	/* Reconfigures autonegotiation (or disables it) */
-	int (*config_aneg)(struct gfar_mii_info *mii_info);
-
-	/* Determines the negotiated speed and duplex */
-	int (*read_status)(struct gfar_mii_info *mii_info);
-
-	/* Clears any pending interrupts */
-	int (*ack_interrupt)(struct gfar_mii_info *mii_info);
-
-	/* Enables or disables interrupts */
-	int (*config_intr)(struct gfar_mii_info *mii_info);
-
-	/* Clears up any memory if needed */
-	void (*close)(struct gfar_mii_info *mii_info);
-};
-
-struct phy_info *get_phy_info(struct gfar_mii_info *mii_info);
-int read_phy_reg(struct net_device *dev, int mii_id, int regnum);
-void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value);
-void mii_clear_phy_interrupt(struct gfar_mii_info *mii_info);
-void mii_configure_phy_interrupt(struct gfar_mii_info *mii_info, u32 interrupts);
-
-struct dm9161_private {
-	struct timer_list timer;
-	int resetdone;
-};
-
-#endif /* GIANFAR_PHY_H */