Staging: et131x: remove unused PCI identifiers

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/et131x/et1310_phy.h

@@ -63,9 +63,6 @@
 
 #define TRUEPHY_SUCCESS 0
 #define TRUEPHY_FAILURE 1
-typedef void *TRUEPHY_HANDLE;
-typedef void *TRUEPHY_PLATFORM_HANDLE;
-typedef void *TRUEPHY_OSAL_HANDLE;
 
 /* MI Register Addresses */
 #define MI_CONTROL_REG                      0
@@ -742,28 +739,6 @@ typedef union _MI_LCR2_t {
 
 /* MI Register 29 - 31: Reserved Reg(0x1D - 0x1E) */
 
-/* TruePHY headers */
-typedef struct _TRUEPHY_ACCESS_MI_REGS_ {
-	TRUEPHY_HANDLE hTruePhy;
-	int32_t nPhyId;
-	u8 bReadWrite;
-	u8 *pbyRegs;
-	u8 *pwData;
-	int32_t nRegCount;
-} TRUEPHY_ACCESS_MI_REGS, *PTRUEPHY_ACCESS_MI_REGS;
-
-/* TruePHY headers */
-typedef struct _TAG_TPAL_ACCESS_MI_REGS_ {
-	u32 nPhyId;
-	u8 bReadWrite;
-	u32 nRegCount;
-	u16 Data[4096];
-	u8 Regs[4096];
-} TPAL_ACCESS_MI_REGS, *PTPAL_ACCESS_MI_REGS;
-
-
-typedef TRUEPHY_HANDLE TPAL_HANDLE;
-
 /* Forward declaration of the private adapter structure */
 struct et131x_adapter;
 

drivers/staging/et131x/et1310_pm.h

@@ -61,54 +61,24 @@
 
 #include "et1310_address_map.h"
 
-#define MAX_WOL_PACKET_SIZE    0x80
-#define MAX_WOL_MASK_SIZE      (MAX_WOL_PACKET_SIZE / 8)
-#define NUM_WOL_PATTERNS       0x5
-#define CRC16_POLY             0x1021
-
 typedef struct _MP_POWER_MGMT {
 	/* variable putting the phy into coma mode when boot up with no cable
 	 * plugged in after 5 seconds
 	 */
 	u8 TransPhyComaModeOnBoot;
 
-	/* Array holding the five CRC values that the device is currently
-	 * using for WOL.  This will be queried when a pattern is to be
-	 * removed.
-	 */
-	u32 localWolAndCrc0;
-	u16 WOLPatternList[NUM_WOL_PATTERNS];
-	u8 WOLMaskList[NUM_WOL_PATTERNS][MAX_WOL_MASK_SIZE];
-	u32 WOLMaskSize[NUM_WOL_PATTERNS];
-
-	/* IP address */
-	union {
-		u32 u32;
-		u8 u8[4];
-	} IPAddress;
-
-	/* Current Power state of the adapter. */
-	bool WOLState;
-	bool WOLEnabled;
-	bool Failed10Half;
-	bool bFailedStateTransition;
-
 	/* Next two used to save power information at power down. This
 	 * information will be used during power up to set up parts of Power
 	 * Management in JAGCore
 	 */
-	u32 tx_en;
-	u32 rx_en;
 	u16 PowerDownSpeed;
 	u8 PowerDownDuplex;
 } MP_POWER_MGMT, *PMP_POWER_MGMT;
 
 /* Forward declaration of the private adapter structure
- * ( IS THERE A WAY TO DO THIS WITH A TYPEDEF??? )
  */
 struct et131x_adapter;
 
-u16 CalculateCCITCRC16(u8 *Pattern, u8 *Mask, u32 MaskSize);
 void EnablePhyComa(struct et131x_adapter *adapter);
 void DisablePhyComa(struct et131x_adapter *adapter);
 

drivers/staging/et131x/et131x_defs.h

@@ -61,7 +61,6 @@
 
 /* Packet and header sizes */
 #define NIC_MIN_PACKET_SIZE	60
-#define NIC_HEADER_SIZE		ETH_HLEN	/* 14 */
 
 /* Multicast list size */
 #define NIC_MAX_MCAST_LIST	128
@@ -102,20 +101,13 @@
 #define fMP_ADAPTER_NOT_READY_MASK	0x3ff00000
 
 /* Some offsets in PCI config space that are actually used. */
-#define ET1310_PCI_PM_CAPABILITY	0x40
-#define ET1310_PCI_PM_CSR		0x44
 #define ET1310_PCI_MAX_PYLD		0x4C
-#define ET1310_PCI_DEV_CTRL		0x50
-#define ET1310_PCI_DEV_STAT		0x52
 #define ET1310_NMI_DISABLE		0x61
 #define ET1310_PCI_MAC_ADDRESS		0xA4
 #define ET1310_PCI_EEPROM_STATUS	0xB2
-#define ET1310_PCI_PHY_INDEX_REG	0xB4
 #define ET1310_PCI_ACK_NACK		0xC0
 #define ET1310_PCI_REPLAY		0xC2
 #define ET1310_PCI_L0L1LATENCY		0xCF
-#define ET1310_PCI_SEL_PHY_CTRL		0xE4
-#define ET1310_PCI_ADVANCED_ERR		0x100
 
 /* PCI Vendor/Product IDs */
 #define ET131X_PCI_VENDOR_ID		0x11C1	/* Agere Systems */