Merge branch 'phy_device_type'

Johan Hovold says:

====================
net: phy: add device-type abstraction

This series adds device and device-type abstractions to the micrel
driver, and enables support for RMII-reference clock selection for
KSZ8081 and KSZ8091 devices.

While adding support for more features for the Micrel PHYs mentioned
above, it became apparent that the configuration space is much too large
and that adding type-specific callbacks will simply not scale. Instead I
added a driver_data field to struct phy_device, which can be used to
store static device type data that can be parsed and acted on in
generic driver callbacks. This allows a lot of duplicated code to be
removed, and should make it much easier to add new features or deal with
device-type quirks in the future.

The series has been tested on a dual KSZ8081 setup. Further testing on
other Micrel PHYs would be much appreciated.

The recent commit a95a18afe4c8 ("phy/micrel: KSZ8031RNL RMII clock
reconfiguration bug") currently prevents KSZ8031 PHYs from using the
generic config-init. Bruno, who is the author of that patch, has agreed
to test this series and some follow-up diagnostic patches to determine
how best to incorporate these devices as well. I intend to send a
follow-up patch that removes the custom 8031 config-init and documents
this quirk, but the current series can be applied meanwhile.

These patches are against net-next which contains some already merged
prerequisite patches to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/micrel.txt

@@ -6,8 +6,8 @@ Optional properties:
 
  - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs.
 
-              Configure the LED mode with single value. The list of PHYs and
-	      the bits that are currently supported:
+	Configure the LED mode with single value. The list of PHYs and the
+	bits that are currently supported:
 
 	KSZ8001: register 0x1e, bits 15..14
 	KSZ8041: register 0x1e, bits 15..14
@@ -19,8 +19,19 @@ Optional properties:
 
 	See the respective PHY datasheet for the mode values.
 
+ - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select
+						bit selects 25 MHz mode
+
+	Setting the RMII Reference Clock Select bit enables 25 MHz rather
+	than 50 MHz clock mode.
+
+	Note that this option in only needed for certain PHY revisions with a
+	non-standard, inverted function of this configuration bit.
+	Specifically, a clock reference ("rmii-ref" below) is always needed to
+	actually select a mode.
+
  - clocks, clock-names: contains clocks according to the common clock bindings.
 
 	supported clocks:
-	      - KSZ8021, KSZ8031: "rmii-ref": The RMII refence input clock. Used
-		to determine the XI input clock.
+	- KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference
+	  input clock. Used to determine the XI input clock.

include/linux/micrel_phy.h

@@ -37,7 +37,6 @@
 
 /* struct phy_device dev_flags definitions */
 #define MICREL_PHY_50MHZ_CLK	0x00000001
-#define MICREL_PHY_25MHZ_CLK	0x00000002
 
 #define MICREL_KSZ9021_EXTREG_CTRL	0xB
 #define MICREL_KSZ9021_EXTREG_DATA_WRITE	0xC

include/linux/phy.h

@@ -433,6 +433,7 @@ struct phy_device {
  *   by this PHY
  * flags: A bitfield defining certain other features this PHY
  *   supports (like interrupts)
+ * driver_data: static driver data
  *
  * The drivers must implement config_aneg and read_status.  All
  * other functions are optional. Note that none of these
@@ -448,6 +449,7 @@ struct phy_driver {
 	unsigned int phy_id_mask;
 	u32 features;
 	u32 flags;
+	const void *driver_data;
 
 	/*
 	 * Called to issue a PHY software reset