Skip to content

L
linux
Commit d1a6f4f1 authored by Paul Gortmaker's avatar Paul Gortmaker
Browse files
Options

block: delete super ancient PC-XT driver for 1980's hardware 

This driver was for the 8 bit ISA cards that were installed in
the PC-XT machines of 1980 vintage.  They supported the dual
ribbon cable MFM drives of 10-20MB capacity, and ran at a 3:1
interleave, giving performance on the order of 128kB/s.

By the introduction of the PC-AT (286) these controllers were
already scrapped in favour of 16 bit controllers with some onboard
RAM that could support a 1:1 interleave.

The git history doesn't show any evidence of runtime fixes that
would reflect active usage; instead just the usual tree-wide API
type changes/cleanups.  Going back to in-source changelogs, the
last "runtime" fix that is evident is something I did over a
dozen years ago[1] -- and even back then, the hardware was long
since unavailable, so that ancient fix was also not runtime tested.

The time is long overdue for this to get flushed, so lets get
rid of it before anyone wastes more time doing builds and sparse
checks etc. on long since dead code.

[1] http://lkml.indiana.edu/hypermail/linux/kernel/0102.2/0027.htmlSigned-off-by: default avatarPaul Gortmaker <paul.gortmaker@windriver.com>
parent d1c3ed66
Show whitespace changes
Inline Side-by-side
Showing with 0 additions and 1271 deletions
drivers/block/Kconfig
View file @ d1a6f4f1
...@@ -63,19 +63,6 @@ config AMIGA_Z2RAM ...@@ -63,19 +63,6 @@ config AMIGA_Z2RAM
To compile this driver as a module, choose M here: the To compile this driver as a module, choose M here: the
module will be called z2ram. module will be called z2ram.
config BLK_DEV_XD
tristate "XT hard disk support"
depends on ISA && ISA_DMA_API
select CHECK_SIGNATURE
help
Very old 8 bit hard disk controllers used in the IBM XT computer
will be supported if you say Y here.
To compile this driver as a module, choose M here: the
module will be called xd.
It's pretty unlikely that you have one of these: say N.
config GDROM config GDROM
tristate "SEGA Dreamcast GD-ROM drive" tristate "SEGA Dreamcast GD-ROM drive"
depends on SH_DREAMCAST depends on SH_DREAMCAST
......
drivers/block/Makefile
View file @ d1a6f4f1
...@@ -15,7 +15,6 @@ obj-$(CONFIG_ATARI_FLOPPY) += ataflop.o ...@@ -15,7 +15,6 @@ obj-$(CONFIG_ATARI_FLOPPY) += ataflop.o
obj-$(CONFIG_AMIGA_Z2RAM) += z2ram.o obj-$(CONFIG_AMIGA_Z2RAM) += z2ram.o
obj-$(CONFIG_BLK_DEV_RAM) += brd.o obj-$(CONFIG_BLK_DEV_RAM) += brd.o
obj-$(CONFIG_BLK_DEV_LOOP) += loop.o obj-$(CONFIG_BLK_DEV_LOOP) += loop.o
obj-$(CONFIG_BLK_DEV_XD) += xd.o
obj-$(CONFIG_BLK_CPQ_DA) += cpqarray.o obj-$(CONFIG_BLK_CPQ_DA) += cpqarray.o
obj-$(CONFIG_BLK_CPQ_CISS_DA) += cciss.o obj-$(CONFIG_BLK_CPQ_CISS_DA) += cciss.o
obj-$(CONFIG_BLK_DEV_DAC960) += DAC960.o obj-$(CONFIG_BLK_DEV_DAC960) += DAC960.o
......
drivers/block/xd.c deleted 100644 → 0
View file @ d1c3ed66
/*
* This file contains the driver for an XT hard disk controller
* (at least the DTC 5150X) for Linux.
*
* Author: Pat Mackinlay, pat@it.com.au
* Date: 29/09/92
*
* Revised: 01/01/93, ...
*
* Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler,
* kevinf@agora.rain.com)
* Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and
* Wim Van Dorst.
*
* Revised: 04/04/94 by Risto Kankkunen
* Moved the detection code from xd_init() to xd_geninit() as it needed
* interrupts enabled and Linus didn't want to enable them in that first
* phase. xd_geninit() is the place to do these kinds of things anyway,
* he says.
*
* Modularized: 04/10/96 by Todd Fries, tfries@umr.edu
*
* Revised: 13/12/97 by Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl
* Fixed some problems with disk initialization and module initiation.
* Added support for manual geometry setting (except Seagate controllers)
* in form:
* xd_geo=<cyl_xda>,<head_xda>,<sec_xda>[,<cyl_xdb>,<head_xdb>,<sec_xdb>]
* Recovered DMA access. Abridged messages. Added support for DTC5051CX,
* WD1002-27X & XEBEC controllers. Driver uses now some jumper settings.
* Extended ioctl() support.
*
* Bugfix: 15/02/01, Paul G. - inform queue layer of tiny xd_maxsect.
*
*/
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/mm.h>
#include <linux/fs.h>
#include <linux/kernel.h>
#include <linux/timer.h>
#include <linux/genhd.h>
#include <linux/hdreg.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/wait.h>
#include <linux/blkdev.h>
#include <linux/mutex.h>
#include <linux/blkpg.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/gfp.h>
#include <asm/uaccess.h>
#include <asm/dma.h>
#include "xd.h"
static DEFINE_MUTEX(xd_mutex);
static void __init do_xd_setup (int *integers);
#ifdef MODULE
static int xd[5] = { -1,-1,-1,-1, };
#endif
#define XD_DONT_USE_DMA 0 /* Initial value. may be overriden using
"nodma" module option */
#define XD_INIT_DISK_DELAY (30) /* 30 ms delay during disk initialization */
/* Above may need to be increased if a problem with the 2nd drive detection
(ST11M controller) or resetting a controller (WD) appears */
static XD_INFO xd_info[XD_MAXDRIVES];
/* If you try this driver and find that your card is not detected by the driver at bootup, you need to add your BIOS
signature and details to the following list of signatures. A BIOS signature is a string embedded into the first
few bytes of your controller's on-board ROM BIOS. To find out what yours is, use something like MS-DOS's DEBUG
command. Run DEBUG, and then you can examine your BIOS signature with:
d xxxx:0000
where xxxx is the segment of your controller (like C800 or D000 or something). On the ASCII dump at the right, you should
be able to see a string mentioning the manufacturer's copyright etc. Add this string into the table below. The parameters
in the table are, in order:
offset ; this is the offset (in bytes) from the start of your ROM where the signature starts
signature ; this is the actual text of the signature
xd_?_init_controller ; this is the controller init routine used by your controller
xd_?_init_drive ; this is the drive init routine used by your controller
The controllers directly supported at the moment are: DTC 5150x, WD 1004A27X, ST11M/R and override. If your controller is
made by the same manufacturer as one of these, try using the same init routines as they do. If that doesn't work, your
best bet is to use the "override" routines. These routines use a "portable" method of getting the disk's geometry, and
may work with your card. If none of these seem to work, try sending me some email and I'll see what I can do <grin>.
NOTE: You can now specify your XT controller's parameters from the command line in the form xd=TYPE,IRQ,IO,DMA. The driver
should be able to detect your drive's geometry from this info. (eg: xd=0,5,0x320,3 is the "standard"). */
#include <asm/page.h>
#define xd_dma_mem_alloc(size) __get_dma_pages(GFP_KERNEL,get_order(size))
#define xd_dma_mem_free(addr, size) free_pages(addr, get_order(size))
static char *xd_dma_buffer;
static XD_SIGNATURE xd_sigs[] __initdata = {
{ 0x0000,"Override geometry handler",NULL,xd_override_init_drive,"n unknown" }, /* Pat Mackinlay, pat@it.com.au */
{ 0x0008,"[BXD06 (C) DTC 17-MAY-1985]",xd_dtc_init_controller,xd_dtc5150cx_init_drive," DTC 5150CX" }, /* Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl */
{ 0x000B,"CRD18A Not an IBM rom. (C) Copyright Data Technology Corp. 05/31/88",xd_dtc_init_controller,xd_dtc_init_drive," DTC 5150X" }, /* Todd Fries, tfries@umr.edu */
{ 0x000B,"CXD23A Not an IBM ROM (C)Copyright Data Technology Corp 12/03/88",xd_dtc_init_controller,xd_dtc_init_drive," DTC 5150X" }, /* Pat Mackinlay, pat@it.com.au */
{ 0x0008,"07/15/86(C) Copyright 1986 Western Digital Corp.",xd_wd_init_controller,xd_wd_init_drive," Western Dig. 1002-27X" }, /* Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl */
{ 0x0008,"06/24/88(C) Copyright 1988 Western Digital Corp.",xd_wd_init_controller,xd_wd_init_drive," Western Dig. WDXT-GEN2" }, /* Dan Newcombe, newcombe@aa.csc.peachnet.edu */
{ 0x0015,"SEAGATE ST11 BIOS REVISION",xd_seagate_init_controller,xd_seagate_init_drive," Seagate ST11M/R" }, /* Salvador Abreu, spa@fct.unl.pt */
{ 0x0010,"ST11R BIOS",xd_seagate_init_controller,xd_seagate_init_drive," Seagate ST11M/R" }, /* Risto Kankkunen, risto.kankkunen@cs.helsinki.fi */
{ 0x0010,"ST11 BIOS v1.7",xd_seagate_init_controller,xd_seagate_init_drive," Seagate ST11R" }, /* Alan Hourihane, alanh@fairlite.demon.co.uk */
{ 0x1000,"(c)Copyright 1987 SMS",xd_omti_init_controller,xd_omti_init_drive,"n OMTI 5520" }, /* Dirk Melchers, dirk@merlin.nbg.sub.org */
{ 0x0006,"COPYRIGHT XEBEC (C) 1984",xd_xebec_init_controller,xd_xebec_init_drive," XEBEC" }, /* Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl */
{ 0x0008,"(C) Copyright 1984 Western Digital Corp", xd_wd_init_controller, xd_wd_init_drive," Western Dig. 1002s-wx2" },
{ 0x0008,"(C) Copyright 1986 Western Digital Corporation", xd_wd_init_controller, xd_wd_init_drive," 1986 Western Digital" }, /* jfree@sovereign.org */
};
static unsigned int xd_bases[] __initdata =
{
0xC8000, 0xCA000, 0xCC000,
0xCE000, 0xD0000, 0xD2000,
0xD4000, 0xD6000, 0xD8000,
0xDA000, 0xDC000, 0xDE000,
0xE0000
};
static DEFINE_SPINLOCK(xd_lock);
static struct gendisk *xd_gendisk[2];
static int xd_getgeo(struct block_device *bdev, struct hd_geometry *geo);
static const struct block_device_operations xd_fops = {
.owner = THIS_MODULE,
.ioctl = xd_ioctl,
.getgeo = xd_getgeo,
};
static DECLARE_WAIT_QUEUE_HEAD(xd_wait_int);
static u_char xd_drives, xd_irq = 5, xd_dma = 3, xd_maxsectors;
static u_char xd_override __initdata = 0, xd_type __initdata = 0;
static u_short xd_iobase = 0x320;
static int xd_geo[XD_MAXDRIVES*3] __initdata = { 0, };
static volatile int xdc_busy;
static struct timer_list xd_watchdog_int;
static volatile u_char xd_error;
static bool nodma = XD_DONT_USE_DMA;
static struct request_queue *xd_queue;
/* xd_init: register the block device number and set up pointer tables */
static int __init xd_init(void)
{
u_char i,controller;
unsigned int address;
int err;
#ifdef MODULE
{
u_char count = 0;
for (i = 4; i > 0; i--)
if (((xd[i] = xd[i-1]) >= 0) && !count)
count = i;
if ((xd[0] = count))
do_xd_setup(xd);
}
#endif
init_timer (&xd_watchdog_int); xd_watchdog_int.function = xd_watchdog;
err = -EBUSY;
if (register_blkdev(XT_DISK_MAJOR, "xd"))
goto out1;
err = -ENOMEM;
xd_queue = blk_init_queue(do_xd_request, &xd_lock);
if (!xd_queue)
goto out1a;
if (xd_detect(&controller,&address)) {
printk("Detected a%s controller (type %d) at address %06x\n",
xd_sigs[controller].name,controller,address);
if (!request_region(xd_iobase,4,"xd")) {
printk("xd: Ports at 0x%x are not available\n",
xd_iobase);
goto out2;
}
if (controller)
xd_sigs[controller].init_controller(address);
xd_drives = xd_initdrives(xd_sigs[controller].init_drive);
printk("Detected %d hard drive%s (using IRQ%d & DMA%d)\n",
xd_drives,xd_drives == 1 ? "" : "s",xd_irq,xd_dma);
}
/*
* With the drive detected, xd_maxsectors should now be known.
* If xd_maxsectors is 0, nothing was detected and we fall through
* to return -ENODEV
*/
if (!xd_dma_buffer && xd_maxsectors) {
xd_dma_buffer = (char *)xd_dma_mem_alloc(xd_maxsectors * 0x200);
if (!xd_dma_buffer) {
printk(KERN_ERR "xd: Out of memory.\n");
goto out3;
}
}
err = -ENODEV;
if (!xd_drives)
goto out3;
for (i = 0; i < xd_drives; i++) {
XD_INFO *p = &xd_info[i];
struct gendisk *disk = alloc_disk(64);
if (!disk)
goto Enomem;
p->unit = i;
disk->major = XT_DISK_MAJOR;
disk->first_minor = i<<6;
sprintf(disk->disk_name, "xd%c", i+'a');
disk->fops = &xd_fops;
disk->private_data = p;
disk->queue = xd_queue;
set_capacity(disk, p->heads * p->cylinders * p->sectors);
printk(" %s: CHS=%d/%d/%d\n", disk->disk_name,
p->cylinders, p->heads, p->sectors);
xd_gendisk[i] = disk;
}
err = -EBUSY;
if (request_irq(xd_irq,xd_interrupt_handler, 0, "XT hard disk", NULL)) {
printk("xd: unable to get IRQ%d\n",xd_irq);
goto out4;
}
if (request_dma(xd_dma,"xd")) {
printk("xd: unable to get DMA%d\n",xd_dma);
goto out5;
}
/* xd_maxsectors depends on controller - so set after detection */
blk_queue_max_hw_sectors(xd_queue, xd_maxsectors);
for (i = 0; i < xd_drives; i++)
add_disk(xd_gendisk[i]);
return 0;
out5:
free_irq(xd_irq, NULL);
out4:
for (i = 0; i < xd_drives; i++)
put_disk(xd_gendisk[i]);
out3:
if (xd_maxsectors)
release_region(xd_iobase,4);
if (xd_dma_buffer)
xd_dma_mem_free((unsigned long)xd_dma_buffer,
xd_maxsectors * 0x200);
out2:
blk_cleanup_queue(xd_queue);
out1a:
unregister_blkdev(XT_DISK_MAJOR, "xd");
out1:
return err;
Enomem:
err = -ENOMEM;
while (i--)
put_disk(xd_gendisk[i]);
goto out3;
}
/* xd_detect: scan the possible BIOS ROM locations for the signature strings */
static u_char __init xd_detect (u_char *controller, unsigned int *address)
{
int i, j;
if (xd_override)
{
*controller = xd_type;
*address = 0;
return(1);
}
for (i = 0; i < ARRAY_SIZE(xd_bases); i++) {
void __iomem *p = ioremap(xd_bases[i], 0x2000);
if (!p)
continue;
for (j = 1; j < ARRAY_SIZE(xd_sigs); j++) {
const char *s = xd_sigs[j].string;
if (check_signature(p + xd_sigs[j].offset, s, strlen(s))) {
*controller = j;
xd_type = j;
*address = xd_bases[i];
iounmap(p);
return 1;
}
}
iounmap(p);
}
return 0;
}
/* do_xd_request: handle an incoming request */
static void do_xd_request (struct request_queue * q)
{
struct request *req;
if (xdc_busy)
return;
req = blk_fetch_request(q);
while (req) {
unsigned block = blk_rq_pos(req);
unsigned count = blk_rq_cur_sectors(req);
XD_INFO *disk = req->rq_disk->private_data;
int res = -EIO;
int retry;
if (req->cmd_type != REQ_TYPE_FS)
goto done;
if (block + count > get_capacity(req->rq_disk))
goto done;
for (retry = 0; (retry < XD_RETRIES) && !res; retry++)
res = xd_readwrite(rq_data_dir(req), disk, req->buffer,
block, count);
done:
/* wrap up, 0 = success, -errno = fail */
if (!__blk_end_request_cur(req, res))
req = blk_fetch_request(q);
}
}
static int xd_getgeo(struct block_device *bdev, struct hd_geometry *geo)
{
XD_INFO *p = bdev->bd_disk->private_data;
geo->heads = p->heads;
geo->sectors = p->sectors;
geo->cylinders = p->cylinders;
return 0;
}
/* xd_ioctl: handle device ioctl's */
static int xd_locked_ioctl(struct block_device *bdev, fmode_t mode, u_int cmd, u_long arg)
{
switch (cmd) {
case HDIO_SET_DMA:
if (!capable(CAP_SYS_ADMIN)) return -EACCES;
if (xdc_busy) return -EBUSY;
nodma = !arg;
if (nodma && xd_dma_buffer) {
xd_dma_mem_free((unsigned long)xd_dma_buffer,
xd_maxsectors * 0x200);
xd_dma_buffer = NULL;
} else if (!nodma && !xd_dma_buffer) {
xd_dma_buffer = (char *)xd_dma_mem_alloc(xd_maxsectors * 0x200);
if (!xd_dma_buffer) {
nodma = XD_DONT_USE_DMA;
return -ENOMEM;
}
}
return 0;
case HDIO_GET_DMA:
return put_user(!nodma, (long __user *) arg);
case HDIO_GET_MULTCOUNT:
return put_user(xd_maxsectors, (long __user *) arg);
default:
return -EINVAL;
}
}
static int xd_ioctl(struct block_device *bdev, fmode_t mode,
unsigned int cmd, unsigned long param)
{
int ret;
mutex_lock(&xd_mutex);
ret = xd_locked_ioctl(bdev, mode, cmd, param);
mutex_unlock(&xd_mutex);
return ret;
}
/* xd_readwrite: handle a read/write request */
static int xd_readwrite (u_char operation,XD_INFO *p,char *buffer,u_int block,u_int count)
{
int drive = p->unit;
u_char cmdblk[6],sense[4];
u_short track,cylinder;
u_char head,sector,control,mode = PIO_MODE,temp;
char **real_buffer;
register int i;
#ifdef DEBUG_READWRITE
printk("xd_readwrite: operation = %s, drive = %d, buffer = 0x%X, block = %d, count = %d\n",operation == READ ? "read" : "write",drive,buffer,block,count);
#endif /* DEBUG_READWRITE */
spin_unlock_irq(&xd_lock);
control = p->control;
if (!xd_dma_buffer)
xd_dma_buffer = (char *)xd_dma_mem_alloc(xd_maxsectors * 0x200);
while (count) {
temp = count < xd_maxsectors ? count : xd_maxsectors;
track = block / p->sectors;
head = track % p->heads;
cylinder = track / p->heads;
sector = block % p->sectors;
#ifdef DEBUG_READWRITE
printk("xd_readwrite: drive = %d, head = %d, cylinder = %d, sector = %d, count = %d\n",drive,head,cylinder,sector,temp);
#endif /* DEBUG_READWRITE */
if (xd_dma_buffer) {
mode = xd_setup_dma(operation == READ ? DMA_MODE_READ : DMA_MODE_WRITE,(u_char *)(xd_dma_buffer),temp * 0x200);
real_buffer = &xd_dma_buffer;
for (i=0; i < (temp * 0x200); i++)
xd_dma_buffer[i] = buffer[i];
}
else
real_buffer = &buffer;
xd_build(cmdblk,operation == READ ? CMD_READ : CMD_WRITE,drive,head,cylinder,sector,temp & 0xFF,control);
switch (xd_command(cmdblk,mode,(u_char *)(*real_buffer),(u_char *)(*real_buffer),sense,XD_TIMEOUT)) {
case 1:
printk("xd%c: %s timeout, recalibrating drive\n",'a'+drive,(operation == READ ? "read" : "write"));
xd_recalibrate(drive);
spin_lock_irq(&xd_lock);
return -EIO;
case 2:
if (sense[0] & 0x30) {
printk("xd%c: %s - ",'a'+drive,(operation == READ ? "reading" : "writing"));
switch ((sense[0] & 0x30) >> 4) {
case 0: printk("drive error, code = 0x%X",sense[0] & 0x0F);
break;
case 1: printk("controller error, code = 0x%X",sense[0] & 0x0F);
break;
case 2: printk("command error, code = 0x%X",sense[0] & 0x0F);
break;
case 3: printk("miscellaneous error, code = 0x%X",sense[0] & 0x0F);
break;
}
}
if (sense[0] & 0x80)
printk(" - CHS = %d/%d/%d\n",((sense[2] & 0xC0) << 2) | sense[3],sense[1] & 0x1F,sense[2] & 0x3F);
/* reported drive number = (sense[1] & 0xE0) >> 5 */
else
printk(" - no valid disk address\n");
spin_lock_irq(&xd_lock);
return -EIO;
}
if (xd_dma_buffer)
for (i=0; i < (temp * 0x200); i++)
buffer[i] = xd_dma_buffer[i];
count -= temp, buffer += temp * 0x200, block += temp;
}
spin_lock_irq(&xd_lock);
return 0;
}
/* xd_recalibrate: recalibrate a given drive and reset controller if necessary */
static void xd_recalibrate (u_char drive)
{
u_char cmdblk[6];
xd_build(cmdblk,CMD_RECALIBRATE,drive,0,0,0,0,0);
if (xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT * 8))
printk("xd%c: warning! error recalibrating, controller may be unstable\n", 'a'+drive);
}
/* xd_interrupt_handler: interrupt service routine */
static irqreturn_t xd_interrupt_handler(int irq, void *dev_id)
{
if (inb(XD_STATUS) & STAT_INTERRUPT) { /* check if it was our device */
#ifdef DEBUG_OTHER
printk("xd_interrupt_handler: interrupt detected\n");
#endif /* DEBUG_OTHER */
outb(0,XD_CONTROL); /* acknowledge interrupt */
wake_up(&xd_wait_int); /* and wake up sleeping processes */
return IRQ_HANDLED;
}
else
printk("xd: unexpected interrupt\n");
return IRQ_NONE;
}
/* xd_setup_dma: set up the DMA controller for a data transfer */
static u_char xd_setup_dma (u_char mode,u_char *buffer,u_int count)
{
unsigned long f;
if (nodma)
return (PIO_MODE);
if (((unsigned long) buffer & 0xFFFF0000) != (((unsigned long) buffer + count) & 0xFFFF0000)) {
#ifdef DEBUG_OTHER
printk("xd_setup_dma: using PIO, transfer overlaps 64k boundary\n");
#endif /* DEBUG_OTHER */
return (PIO_MODE);
}
f=claim_dma_lock();
disable_dma(xd_dma);
clear_dma_ff(xd_dma);
set_dma_mode(xd_dma,mode);
set_dma_addr(xd_dma, (unsigned long) buffer);
set_dma_count(xd_dma,count);
release_dma_lock(f);
return (DMA_MODE); /* use DMA and INT */
}
/* xd_build: put stuff into an array in a format suitable for the controller */
static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control)
{
cmdblk[0] = command;
cmdblk[1] = ((drive & 0x07) << 5) | (head & 0x1F);
cmdblk[2] = ((cylinder & 0x300) >> 2) | (sector & 0x3F);
cmdblk[3] = cylinder & 0xFF;
cmdblk[4] = count;
cmdblk[5] = control;
return (cmdblk);
}
static void xd_watchdog (unsigned long unused)
{
xd_error = 1;
wake_up(&xd_wait_int);
}
/* xd_waitport: waits until port & mask == flags or a timeout occurs. return 1 for a timeout */
static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout)
{
u_long expiry = jiffies + timeout;
int success;
xdc_busy = 1;
while ((success = ((inb(port) & mask) != flags)) && time_before(jiffies, expiry))
schedule_timeout_uninterruptible(1);
xdc_busy = 0;
return (success);
}
static inline u_int xd_wait_for_IRQ (void)
{
unsigned long flags;
xd_watchdog_int.expires = jiffies + 8 * HZ;
add_timer(&xd_watchdog_int);
flags=claim_dma_lock();
enable_dma(xd_dma);
release_dma_lock(flags);
sleep_on(&xd_wait_int);
del_timer(&xd_watchdog_int);
xdc_busy = 0;
flags=claim_dma_lock();
disable_dma(xd_dma);
release_dma_lock(flags);
if (xd_error) {
printk("xd: missed IRQ - command aborted\n");
xd_error = 0;
return (1);
}
return (0);
}
/* xd_command: handle all data transfers necessary for a single command */
static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout)
{
u_char cmdblk[6],csb,complete = 0;
#ifdef DEBUG_COMMAND
printk("xd_command: command = 0x%X, mode = 0x%X, indata = 0x%X, outdata = 0x%X, sense = 0x%X\n",command,mode,indata,outdata,sense);
#endif /* DEBUG_COMMAND */
outb(0,XD_SELECT);
outb(mode,XD_CONTROL);
if (xd_waitport(XD_STATUS,STAT_SELECT,STAT_SELECT,timeout))
return (1);
while (!complete) {
if (xd_waitport(XD_STATUS,STAT_READY,STAT_READY,timeout))
return (1);
switch (inb(XD_STATUS) & (STAT_COMMAND | STAT_INPUT)) {
case 0:
if (mode == DMA_MODE) {
if (xd_wait_for_IRQ())
return (1);
} else
outb(outdata ? *outdata++ : 0,XD_DATA);
break;
case STAT_INPUT:
if (mode == DMA_MODE) {
if (xd_wait_for_IRQ())
return (1);
} else
if (indata)
*indata++ = inb(XD_DATA);
else
inb(XD_DATA);
break;
case STAT_COMMAND:
outb(command ? *command++ : 0,XD_DATA);
break;
case STAT_COMMAND | STAT_INPUT:
complete = 1;
break;
}
}
csb = inb(XD_DATA);
if (xd_waitport(XD_STATUS,0,STAT_SELECT,timeout)) /* wait until deselected */
return (1);
if (csb & CSB_ERROR) { /* read sense data if error */
xd_build(cmdblk,CMD_SENSE,(csb & CSB_LUN) >> 5,0,0,0,0,0);
if (xd_command(cmdblk,0,sense,NULL,NULL,XD_TIMEOUT))
printk("xd: warning! sense command failed!\n");
}
#ifdef DEBUG_COMMAND
printk("xd_command: completed with csb = 0x%X\n",csb);
#endif /* DEBUG_COMMAND */
return (csb & CSB_ERROR);
}
static u_char __init xd_initdrives (void (*init_drive)(u_char drive))
{
u_char cmdblk[6],i,count = 0;
for (i = 0; i < XD_MAXDRIVES; i++) {
xd_build(cmdblk,CMD_TESTREADY,i,0,0,0,0,0);
if (!xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT*8)) {
msleep_interruptible(XD_INIT_DISK_DELAY);
init_drive(count);
count++;
msleep_interruptible(XD_INIT_DISK_DELAY);
}
}
return (count);
}
static void __init xd_manual_geo_set (u_char drive)
{
xd_info[drive].heads = (u_char)(xd_geo[3 * drive + 1]);
xd_info[drive].cylinders = (u_short)(xd_geo[3 * drive]);
xd_info[drive].sectors = (u_char)(xd_geo[3 * drive + 2]);
}
static void __init xd_dtc_init_controller (unsigned int address)
{
switch (address) {
case 0x00000:
case 0xC8000: break; /*initial: 0x320 */
case 0xCA000: xd_iobase = 0x324;
case 0xD0000: /*5150CX*/
case 0xD8000: break; /*5150CX & 5150XL*/
default: printk("xd_dtc_init_controller: unsupported BIOS address %06x\n",address);
break;
}
xd_maxsectors = 0x01; /* my card seems to have trouble doing multi-block transfers? */
outb(0,XD_RESET); /* reset the controller */
}
static void __init xd_dtc5150cx_init_drive (u_char drive)
{
/* values from controller's BIOS - BIOS chip may be removed */
static u_short geometry_table[][4] = {
{0x200,8,0x200,0x100},
{0x267,2,0x267,0x267},
{0x264,4,0x264,0x80},
{0x132,4,0x132,0x0},
{0x132,2,0x80, 0x132},
{0x177,8,0x177,0x0},
{0x132,8,0x84, 0x0},
{}, /* not used */
{0x132,6,0x80, 0x100},
{0x200,6,0x100,0x100},
{0x264,2,0x264,0x80},
{0x280,4,0x280,0x100},
{0x2B9,3,0x2B9,0x2B9},
{0x2B9,5,0x2B9,0x2B9},
{0x280,6,0x280,0x100},
{0x132,4,0x132,0x0}};
u_char n;
n = inb(XD_JUMPER);
n = (drive ? n : (n >> 2)) & 0x33;
n = (n | (n >> 2)) & 0x0F;
if (xd_geo[3*drive])
xd_manual_geo_set(drive);
else
if (n != 7) {
xd_info[drive].heads = (u_char)(geometry_table[n][1]); /* heads */
xd_info[drive].cylinders = geometry_table[n][0]; /* cylinders */
xd_info[drive].sectors = 17; /* sectors */
#if 0
xd_info[drive].rwrite = geometry_table[n][2]; /* reduced write */
xd_info[drive].precomp = geometry_table[n][3] /* write precomp */
xd_info[drive].ecc = 0x0B; /* ecc length */
#endif /* 0 */
}
else {
printk("xd%c: undetermined drive geometry\n",'a'+drive);
return;
}
xd_info[drive].control = 5; /* control byte */
xd_setparam(CMD_DTCSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,geometry_table[n][2],geometry_table[n][3],0x0B);
xd_recalibrate(drive);
}
static void __init xd_dtc_init_drive (u_char drive)
{
u_char cmdblk[6],buf[64];
xd_build(cmdblk,CMD_DTCGETGEOM,drive,0,0,0,0,0);
if (!xd_command(cmdblk,PIO_MODE,buf,NULL,NULL,XD_TIMEOUT * 2)) {
xd_info[drive].heads = buf[0x0A]; /* heads */
xd_info[drive].cylinders = ((u_short *) (buf))[0x04]; /* cylinders */
xd_info[drive].sectors = 17; /* sectors */
if (xd_geo[3*drive])
xd_manual_geo_set(drive);
#if 0
xd_info[drive].rwrite = ((u_short *) (buf + 1))[0x05]; /* reduced write */
xd_info[drive].precomp = ((u_short *) (buf + 1))[0x06]; /* write precomp */
xd_info[drive].ecc = buf[0x0F]; /* ecc length */
#endif /* 0 */
xd_info[drive].control = 0; /* control byte */
xd_setparam(CMD_DTCSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,((u_short *) (buf + 1))[0x05],((u_short *) (buf + 1))[0x06],buf[0x0F]);
xd_build(cmdblk,CMD_DTCSETSTEP,drive,0,0,0,0,7);
if (xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT * 2))
printk("xd_dtc_init_drive: error setting step rate for xd%c\n", 'a'+drive);
}
else
printk("xd_dtc_init_drive: error reading geometry for xd%c\n", 'a'+drive);
}
static void __init xd_wd_init_controller (unsigned int address)
{
switch (address) {
case 0x00000:
case 0xC8000: break; /*initial: 0x320 */
case 0xCA000: xd_iobase = 0x324; break;
case 0xCC000: xd_iobase = 0x328; break;
case 0xCE000: xd_iobase = 0x32C; break;
case 0xD0000: xd_iobase = 0x328; break; /* ? */
case 0xD8000: xd_iobase = 0x32C; break; /* ? */
default: printk("xd_wd_init_controller: unsupported BIOS address %06x\n",address);
break;
}
xd_maxsectors = 0x01; /* this one doesn't wrap properly either... */
outb(0,XD_RESET); /* reset the controller */
msleep(XD_INIT_DISK_DELAY);
}
static void __init xd_wd_init_drive (u_char drive)
{
/* values from controller's BIOS - BIOS may be disabled */
static u_short geometry_table[][4] = {
{0x264,4,0x1C2,0x1C2}, /* common part */
{0x132,4,0x099,0x0},
{0x267,2,0x1C2,0x1C2},
{0x267,4,0x1C2,0x1C2},
{0x334,6,0x335,0x335}, /* 1004 series RLL */
{0x30E,4,0x30F,0x3DC},
{0x30E,2,0x30F,0x30F},
{0x267,4,0x268,0x268},
{0x3D5,5,0x3D6,0x3D6}, /* 1002 series RLL */
{0x3DB,7,0x3DC,0x3DC},
{0x264,4,0x265,0x265},
{0x267,4,0x268,0x268}};
u_char cmdblk[6],buf[0x200];
u_char n = 0,rll,jumper_state,use_jumper_geo;
u_char wd_1002 = (xd_sigs[xd_type].string[7] == '6');
jumper_state = ~(inb(0x322));
if (jumper_state & 0x40)
xd_irq = 9;
rll = (jumper_state & 0x30) ? (0x04 << wd_1002) : 0;
xd_build(cmdblk,CMD_READ,drive,0,0,0,1,0);
if (!xd_command(cmdblk,PIO_MODE,buf,NULL,NULL,XD_TIMEOUT * 2)) {
xd_info[drive].heads = buf[0x1AF]; /* heads */
xd_info[drive].cylinders = ((u_short *) (buf + 1))[0xD6]; /* cylinders */
xd_info[drive].sectors = 17; /* sectors */
if (xd_geo[3*drive])
xd_manual_geo_set(drive);
#if 0
xd_info[drive].rwrite = ((u_short *) (buf))[0xD8]; /* reduced write */
xd_info[drive].wprecomp = ((u_short *) (buf))[0xDA]; /* write precomp */
xd_info[drive].ecc = buf[0x1B4]; /* ecc length */
#endif /* 0 */
xd_info[drive].control = buf[0x1B5]; /* control byte */
use_jumper_geo = !(xd_info[drive].heads) || !(xd_info[drive].cylinders);
if (xd_geo[3*drive]) {
xd_manual_geo_set(drive);
xd_info[drive].control = rll ? 7 : 5;
}
else if (use_jumper_geo) {
n = (((jumper_state & 0x0F) >> (drive << 1)) & 0x03) | rll;
xd_info[drive].cylinders = geometry_table[n][0];
xd_info[drive].heads = (u_char)(geometry_table[n][1]);
xd_info[drive].control = rll ? 7 : 5;
#if 0
xd_info[drive].rwrite = geometry_table[n][2];
xd_info[drive].wprecomp = geometry_table[n][3];
xd_info[drive].ecc = 0x0B;
#endif /* 0 */
}
if (!wd_1002) {
if (use_jumper_geo)
xd_setparam(CMD_WDSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,
geometry_table[n][2],geometry_table[n][3],0x0B);
else
xd_setparam(CMD_WDSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,
((u_short *) (buf))[0xD8],((u_short *) (buf))[0xDA],buf[0x1B4]);
}
/* 1002 based RLL controller requests converted addressing, but reports physical
(physical 26 sec., logical 17 sec.)
1004 based ???? */
if (rll & wd_1002) {
if ((xd_info[drive].cylinders *= 26,
xd_info[drive].cylinders /= 17) > 1023)
xd_info[drive].cylinders = 1023; /* 1024 ? */
#if 0
xd_info[drive].rwrite *= 26;
xd_info[drive].rwrite /= 17;
xd_info[drive].wprecomp *= 26
xd_info[drive].wprecomp /= 17;
#endif /* 0 */
}
}
else
printk("xd_wd_init_drive: error reading geometry for xd%c\n",'a'+drive);
}
static void __init xd_seagate_init_controller (unsigned int address)
{
switch (address) {
case 0x00000:
case 0xC8000: break; /*initial: 0x320 */
case 0xD0000: xd_iobase = 0x324; break;
case 0xD8000: xd_iobase = 0x328; break;
case 0xE0000: xd_iobase = 0x32C; break;
default: printk("xd_seagate_init_controller: unsupported BIOS address %06x\n",address);
break;
}
xd_maxsectors = 0x40;
outb(0,XD_RESET); /* reset the controller */
}
static void __init xd_seagate_init_drive (u_char drive)
{
u_char cmdblk[6],buf[0x200];
xd_build(cmdblk,CMD_ST11GETGEOM,drive,0,0,0,1,0);
if (!xd_command(cmdblk,PIO_MODE,buf,NULL,NULL,XD_TIMEOUT * 2)) {
xd_info[drive].heads = buf[0x04]; /* heads */
xd_info[drive].cylinders = (buf[0x02] << 8) | buf[0x03]; /* cylinders */
xd_info[drive].sectors = buf[0x05]; /* sectors */
xd_info[drive].control = 0; /* control byte */
}
else
printk("xd_seagate_init_drive: error reading geometry from xd%c\n", 'a'+drive);
}
/* Omti support courtesy Dirk Melchers */
static void __init xd_omti_init_controller (unsigned int address)
{
switch (address) {
case 0x00000:
case 0xC8000: break; /*initial: 0x320 */
case 0xD0000: xd_iobase = 0x324; break;
case 0xD8000: xd_iobase = 0x328; break;
case 0xE0000: xd_iobase = 0x32C; break;
default: printk("xd_omti_init_controller: unsupported BIOS address %06x\n",address);
break;
}
xd_maxsectors = 0x40;
outb(0,XD_RESET); /* reset the controller */
}
static void __init xd_omti_init_drive (u_char drive)
{
/* gets infos from drive */
xd_override_init_drive(drive);
/* set other parameters, Hardcoded, not that nice :-) */
xd_info[drive].control = 2;
}
/* Xebec support (AK) */
static void __init xd_xebec_init_controller (unsigned int address)
{
/* iobase may be set manually in range 0x300 - 0x33C
irq may be set manually to 2(9),3,4,5,6,7
dma may be set manually to 1,2,3
(How to detect them ???)
BIOS address may be set manually in range 0x0 - 0xF8000
If you need non-standard settings use the xd=... command */
switch (address) {
case 0x00000:
case 0xC8000: /* initially: xd_iobase==0x320 */
case 0xD0000:
case 0xD2000:
case 0xD4000:
case 0xD6000:
case 0xD8000:
case 0xDA000:
case 0xDC000:
case 0xDE000:
case 0xE0000: break;
default: printk("xd_xebec_init_controller: unsupported BIOS address %06x\n",address);
break;
}
xd_maxsectors = 0x01;
outb(0,XD_RESET); /* reset the controller */
msleep(XD_INIT_DISK_DELAY);
}
static void __init xd_xebec_init_drive (u_char drive)
{
/* values from controller's BIOS - BIOS chip may be removed */
static u_short geometry_table[][5] = {
{0x132,4,0x080,0x080,0x7},
{0x132,4,0x080,0x080,0x17},
{0x264,2,0x100,0x100,0x7},
{0x264,2,0x100,0x100,0x17},
{0x132,8,0x080,0x080,0x7},
{0x132,8,0x080,0x080,0x17},
{0x264,4,0x100,0x100,0x6},
{0x264,4,0x100,0x100,0x17},
{0x2BC,5,0x2BC,0x12C,0x6},
{0x3A5,4,0x3A5,0x3A5,0x7},
{0x26C,6,0x26C,0x26C,0x7},
{0x200,8,0x200,0x100,0x17},
{0x400,5,0x400,0x400,0x7},
{0x400,6,0x400,0x400,0x7},
{0x264,8,0x264,0x200,0x17},
{0x33E,7,0x33E,0x200,0x7}};
u_char n;
n = inb(XD_JUMPER) & 0x0F; /* BIOS's drive number: same geometry
is assumed for BOTH drives */
if (xd_geo[3*drive])
xd_manual_geo_set(drive);
else {
xd_info[drive].heads = (u_char)(geometry_table[n][1]); /* heads */
xd_info[drive].cylinders = geometry_table[n][0]; /* cylinders */
xd_info[drive].sectors = 17; /* sectors */
#if 0
xd_info[drive].rwrite = geometry_table[n][2]; /* reduced write */
xd_info[drive].precomp = geometry_table[n][3] /* write precomp */
xd_info[drive].ecc = 0x0B; /* ecc length */
#endif /* 0 */
}
xd_info[drive].control = geometry_table[n][4]; /* control byte */
xd_setparam(CMD_XBSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,geometry_table[n][2],geometry_table[n][3],0x0B);
xd_recalibrate(drive);
}
/* xd_override_init_drive: this finds disk geometry in a "binary search" style, narrowing in on the "correct" number of heads
etc. by trying values until it gets the highest successful value. Idea courtesy Salvador Abreu (spa@fct.unl.pt). */
static void __init xd_override_init_drive (u_char drive)
{
u_short min[] = { 0,0,0 },max[] = { 16,1024,64 },test[] = { 0,0,0 };
u_char cmdblk[6],i;
if (xd_geo[3*drive])
xd_manual_geo_set(drive);
else {
for (i = 0; i < 3; i++) {
while (min[i] != max[i] - 1) {
test[i] = (min[i] + max[i]) / 2;
xd_build(cmdblk,CMD_SEEK,drive,(u_char) test[0],(u_short) test[1],(u_char) test[2],0,0);
if (!xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT * 2))
min[i] = test[i];
else
max[i] = test[i];
}
test[i] = min[i];
}
xd_info[drive].heads = (u_char) min[0] + 1;
xd_info[drive].cylinders = (u_short) min[1] + 1;
xd_info[drive].sectors = (u_char) min[2] + 1;
}
xd_info[drive].control = 0;
}
/* xd_setup: initialise controller from command line parameters */
static void __init do_xd_setup (int *integers)
{
switch (integers[0]) {
case 4: if (integers[4] < 0)
nodma = 1;
else if (integers[4] < 8)
xd_dma = integers[4];
case 3: if ((integers[3] > 0) && (integers[3] <= 0x3FC))
xd_iobase = integers[3];
case 2: if ((integers[2] > 0) && (integers[2] < 16))
xd_irq = integers[2];
case 1: xd_override = 1;
if ((integers[1] >= 0) && (integers[1] < ARRAY_SIZE(xd_sigs)))
xd_type = integers[1];
case 0: break;
default:printk("xd: too many parameters for xd\n");
}
xd_maxsectors = 0x01;
}
/* xd_setparam: set the drive characteristics */
static void __init xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc)
{
u_char cmdblk[14];
xd_build(cmdblk,command,drive,0,0,0,0,0);
cmdblk[6] = (u_char) (cylinders >> 8) & 0x03;
cmdblk[7] = (u_char) (cylinders & 0xFF);
cmdblk[8] = heads & 0x1F;
cmdblk[9] = (u_char) (rwrite >> 8) & 0x03;
cmdblk[10] = (u_char) (rwrite & 0xFF);
cmdblk[11] = (u_char) (wprecomp >> 8) & 0x03;
cmdblk[12] = (u_char) (wprecomp & 0xFF);
cmdblk[13] = ecc;
/* Some controllers require geometry info as data, not command */
if (xd_command(cmdblk,PIO_MODE,NULL,&cmdblk[6],NULL,XD_TIMEOUT * 2))
printk("xd: error setting characteristics for xd%c\n", 'a'+drive);
}
#ifdef MODULE
module_param_array(xd, int, NULL, 0);
module_param_array(xd_geo, int, NULL, 0);
module_param(nodma, bool, 0);
MODULE_LICENSE("GPL");
void cleanup_module(void)
{
int i;
unregister_blkdev(XT_DISK_MAJOR, "xd");
for (i = 0; i < xd_drives; i++) {
del_gendisk(xd_gendisk[i]);
put_disk(xd_gendisk[i]);
}
blk_cleanup_queue(xd_queue);
release_region(xd_iobase,4);
if (xd_drives) {
free_irq(xd_irq, NULL);
free_dma(xd_dma);
if (xd_dma_buffer)
xd_dma_mem_free((unsigned long)xd_dma_buffer, xd_maxsectors * 0x200);
}
}
#else
static int __init xd_setup (char *str)
{
int ints[5];
get_options (str, ARRAY_SIZE (ints), ints);
do_xd_setup (ints);
return 1;
}
/* xd_manual_geo_init: initialise drive geometry from command line parameters
(used only for WD drives) */
static int __init xd_manual_geo_init (char *str)
{
int i, integers[1 + 3*XD_MAXDRIVES];
get_options (str, ARRAY_SIZE (integers), integers);
if (integers[0]%3 != 0) {
printk("xd: incorrect number of parameters for xd_geo\n");
return 1;
}
for (i = 0; (i < integers[0]) && (i < 3*XD_MAXDRIVES); i++)
xd_geo[i] = integers[i+1];
return 1;
}
__setup ("xd=", xd_setup);
__setup ("xd_geo=", xd_manual_geo_init);
#endif /* MODULE */
module_init(xd_init);
MODULE_ALIAS_BLOCKDEV_MAJOR(XT_DISK_MAJOR);
drivers/block/xd.h deleted 100644 → 0
View file @ d1c3ed66
#ifndef _LINUX_XD_H
#define _LINUX_XD_H
/*
* This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X).
*
* Author: Pat Mackinlay, pat@it.com.au
* Date: 29/09/92
*
* Revised: 01/01/93, ...
*
* Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com)
* Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst.
*/
#include <linux/interrupt.h>
/* XT hard disk controller registers */
#define XD_DATA (xd_iobase + 0x00) /* data RW register */
#define XD_RESET (xd_iobase + 0x01) /* reset WO register */
#define XD_STATUS (xd_iobase + 0x01) /* status RO register */
#define XD_SELECT (xd_iobase + 0x02) /* select WO register */
#define XD_JUMPER (xd_iobase + 0x02) /* jumper RO register */
#define XD_CONTROL (xd_iobase + 0x03) /* DMAE/INTE WO register */
#define XD_RESERVED (xd_iobase + 0x03) /* reserved */
/* XT hard disk controller commands (incomplete list) */
#define CMD_TESTREADY 0x00 /* test drive ready */
#define CMD_RECALIBRATE 0x01 /* recalibrate drive */
#define CMD_SENSE 0x03 /* request sense */
#define CMD_FORMATDRV 0x04 /* format drive */
#define CMD_VERIFY 0x05 /* read verify */
#define CMD_FORMATTRK 0x06 /* format track */
#define CMD_FORMATBAD 0x07 /* format bad track */
#define CMD_READ 0x08 /* read */
#define CMD_WRITE 0x0A /* write */
#define CMD_SEEK 0x0B /* seek */
/* Controller specific commands */
#define CMD_DTCSETPARAM 0x0C /* set drive parameters (DTC 5150X & CX only?) */
#define CMD_DTCGETECC 0x0D /* get ecc error length (DTC 5150X only?) */
#define CMD_DTCREADBUF 0x0E /* read sector buffer (DTC 5150X only?) */
#define CMD_DTCWRITEBUF 0x0F /* write sector buffer (DTC 5150X only?) */
#define CMD_DTCREMAPTRK 0x11 /* assign alternate track (DTC 5150X only?) */
#define CMD_DTCGETPARAM 0xFB /* get drive parameters (DTC 5150X only?) */
#define CMD_DTCSETSTEP 0xFC /* set step rate (DTC 5150X only?) */
#define CMD_DTCSETGEOM 0xFE /* set geometry data (DTC 5150X only?) */
#define CMD_DTCGETGEOM 0xFF /* get geometry data (DTC 5150X only?) */
#define CMD_ST11GETGEOM 0xF8 /* get geometry data (Seagate ST11R/M only?) */
#define CMD_WDSETPARAM 0x0C /* set drive parameters (WD 1004A27X only?) */
#define CMD_XBSETPARAM 0x0C /* set drive parameters (XEBEC only?) */
/* Bits for command status byte */
#define CSB_ERROR 0x02 /* error */
#define CSB_LUN 0x20 /* logical Unit Number */
/* XT hard disk controller status bits */
#define STAT_READY 0x01 /* controller is ready */
#define STAT_INPUT 0x02 /* data flowing from controller to host */
#define STAT_COMMAND 0x04 /* controller in command phase */
#define STAT_SELECT 0x08 /* controller is selected */
#define STAT_REQUEST 0x10 /* controller requesting data */
#define STAT_INTERRUPT 0x20 /* controller requesting interrupt */
/* XT hard disk controller control bits */
#define PIO_MODE 0x00 /* control bits to set for PIO */
#define DMA_MODE 0x03 /* control bits to set for DMA & interrupt */
#define XD_MAXDRIVES 2 /* maximum 2 drives */
#define XD_TIMEOUT HZ /* 1 second timeout */
#define XD_RETRIES 4 /* maximum 4 retries */
#undef DEBUG /* define for debugging output */
#ifdef DEBUG
#define DEBUG_STARTUP /* debug driver initialisation */
#define DEBUG_OVERRIDE /* debug override geometry detection */
#define DEBUG_READWRITE /* debug each read/write command */
#define DEBUG_OTHER /* debug misc. interrupt/DMA stuff */
#define DEBUG_COMMAND /* debug each controller command */
#endif /* DEBUG */
/* this structure defines the XT drives and their types */
typedef struct {
u_char heads;
u_short cylinders;
u_char sectors;
u_char control;
int unit;
} XD_INFO;
/* this structure defines a ROM BIOS signature */
typedef struct {
unsigned int offset;
const char *string;
void (*init_controller)(unsigned int address);
void (*init_drive)(u_char drive);
const char *name;
} XD_SIGNATURE;
#ifndef MODULE
static int xd_manual_geo_init (char *command);
#endif /* MODULE */
static u_char xd_detect (u_char *controller, unsigned int *address);
static u_char xd_initdrives (void (*init_drive)(u_char drive));
static void do_xd_request (struct request_queue * q);
static int xd_ioctl (struct block_device *bdev,fmode_t mode,unsigned int cmd,unsigned long arg);
static int xd_readwrite (u_char operation,XD_INFO *disk,char *buffer,u_int block,u_int count);
static void xd_recalibrate (u_char drive);
static irqreturn_t xd_interrupt_handler(int irq, void *dev_id);
static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count);
static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control);
static void xd_watchdog (unsigned long unused);
static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout);
static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout);
/* card specific setup and geometry gathering code */
static void xd_dtc_init_controller (unsigned int address);
static void xd_dtc5150cx_init_drive (u_char drive);
static void xd_dtc_init_drive (u_char drive);
static void xd_wd_init_controller (unsigned int address);
static void xd_wd_init_drive (u_char drive);
static void xd_seagate_init_controller (unsigned int address);
static void xd_seagate_init_drive (u_char drive);
static void xd_omti_init_controller (unsigned int address);
static void xd_omti_init_drive (u_char drive);
static void xd_xebec_init_controller (unsigned int address);
static void xd_xebec_init_drive (u_char drive);
static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc);
static void xd_override_init_drive (u_char drive);
#endif /* _LINUX_XD_H */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7