Commit e35ec126 authored by Alexander Duyck's avatar Alexander Duyck Committed by David S. Miller

ixgbe: only register DCA requester once

The current driver tries to re-register the DCA requester after reset and
this is not correct.  This change makes it so all we are doing is resetting
the DCA registers after reset and not re-adding the requester.
Signed-off-by: default avatarAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 7e0e99ef
......@@ -411,6 +411,9 @@ static void ixgbe_setup_dca(struct ixgbe_adapter *adapter)
if (!(adapter->flags & IXGBE_FLAG_DCA_ENABLED))
return;
/* always use CB2 mode, difference is masked in the CB driver */
IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL, 2);
for (i = 0; i < adapter->num_tx_queues; i++) {
adapter->tx_ring[i].cpu = -1;
ixgbe_update_tx_dca(adapter, &adapter->tx_ring[i]);
......@@ -432,9 +435,6 @@ static int __ixgbe_notify_dca(struct device *dev, void *data)
/* if we're already enabled, don't do it again */
if (adapter->flags & IXGBE_FLAG_DCA_ENABLED)
break;
/* Always use CB2 mode, difference is masked
* in the CB driver. */
IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL, 2);
if (dca_add_requester(dev) == 0) {
adapter->flags |= IXGBE_FLAG_DCA_ENABLED;
ixgbe_setup_dca(adapter);
......@@ -2767,13 +2767,6 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
netif_carrier_off(netdev);
#ifdef CONFIG_IXGBE_DCA
if (adapter->flags & IXGBE_FLAG_DCA_ENABLED) {
adapter->flags &= ~IXGBE_FLAG_DCA_ENABLED;
dca_remove_requester(&adapter->pdev->dev);
}
#endif
if (!pci_channel_offline(adapter->pdev))
ixgbe_reset(adapter);
ixgbe_clean_all_tx_rings(adapter);
......@@ -2781,13 +2774,7 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
#ifdef CONFIG_IXGBE_DCA
/* since we reset the hardware DCA settings were cleared */
if (dca_add_requester(&adapter->pdev->dev) == 0) {
adapter->flags |= IXGBE_FLAG_DCA_ENABLED;
/* always use CB2 mode, difference is masked
* in the CB driver */
IXGBE_WRITE_REG(hw, IXGBE_DCA_CTRL, 2);
ixgbe_setup_dca(adapter);
}
#endif
}
......@@ -5354,9 +5341,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
#ifdef CONFIG_IXGBE_DCA
if (dca_add_requester(&pdev->dev) == 0) {
adapter->flags |= IXGBE_FLAG_DCA_ENABLED;
/* always use CB2 mode, difference is masked
* in the CB driver */
IXGBE_WRITE_REG(hw, IXGBE_DCA_CTRL, 2);
ixgbe_setup_dca(adapter);
}
#endif
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment