Base Au1200 2.6 support.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/Kconfig

@@ -642,6 +642,10 @@ config SGI_IP32
 	help
 	  If you want this kernel to run on SGI O2 workstation, say Y here.
 
+config SOC_AU1200
+	bool
+	select SOC_AU1X00
+
 config SOC_AU1X00
 	bool "Support for AMD/Alchemy Au1X00 SOCs"
 	select SYS_SUPPORTS_32BIT_KERNEL
@@ -702,6 +706,13 @@ config MIPS_PB1550
 	select HW_HAS_PCI
 	select MIPS_DISABLE_OBSOLETE_IDE
 
+config MIPS_PB1200
+	bool "AMD Alchemy PB1200 board"
+	select SOC_AU1200
+	select DMA_NONCOHERENT
+	select MIPS_DISABLE_OBSOLETE_IDE
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
 config MIPS_DB1000
 	bool "DB1000 board"
 	depends on SOC_AU1000
@@ -732,6 +743,13 @@ config MIPS_BOSPORUS
 	depends on SOC_AU1500
 	select DMA_NONCOHERENT
 
+config MIPS_DB1200
+	bool "AMD Alchemy DB1200 board"
+	select SOC_AU1200
+	select DMA_NONCOHERENT
+	select MIPS_DISABLE_OBSOLETE_IDE
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
 config MIPS_MIRAGE
 	bool "Mirage board"
 	depends on SOC_AU1500

arch/mips/Makefile

@@ -265,6 +265,13 @@ libs-$(CONFIG_MIPS_PB1550)	+= arch/mips/au1000/pb1550/
 cflags-$(CONFIG_MIPS_PB1550)	+= -Iinclude/asm-mips/mach-pb1x00
 load-$(CONFIG_MIPS_PB1550)	+= 0xffffffff80100000
 
+#
+# AMD Alchemy Pb1200 eval board
+#
+libs-$(CONFIG_MIPS_PB1200)	+= arch/mips/au1000/pb1200/
+cflags-$(CONFIG_MIPS_PB1200)	+= -Iinclude/asm-mips/mach-pb1x00
+load-$(CONFIG_MIPS_PB1200)	+= 0xffffffff80100000
+
 #
 # AMD Alchemy Db1000 eval board
 #
@@ -293,6 +300,13 @@ libs-$(CONFIG_MIPS_DB1550)	+= arch/mips/au1000/db1x00/
 cflags-$(CONFIG_MIPS_DB1550)	+= -Iinclude/asm-mips/mach-db1x00
 load-$(CONFIG_MIPS_DB1550)	+= 0xffffffff80100000
 
+#
+# AMD Alchemy Db1200 eval board
+#
+libs-$(CONFIG_MIPS_DB1200)	+= arch/mips/au1000/pb1200/
+cflags-$(CONFIG_MIPS_DB1200)	+= -Iinclude/asm-mips/mach-db1x00
+load-$(CONFIG_MIPS_DB1200)	+= 0xffffffff80100000
+
 #
 # AMD Alchemy Bosporus eval board
 #

arch/mips/au1000/common/au1xxx_irqmap.c

@@ -173,14 +173,14 @@ au1xxx_irq_map_t au1xxx_ic0_map[] = {
 	{ AU1550_PSC1_INT, INTC_INT_HIGH_LEVEL, 0},
 	{ AU1550_PSC2_INT, INTC_INT_HIGH_LEVEL, 0},
 	{ AU1550_PSC3_INT, INTC_INT_HIGH_LEVEL, 0},
-	{ AU1550_TOY_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1550_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1550_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1550_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
-	{ AU1550_RTC_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1550_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1550_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1550_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
+	{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
 	{ AU1550_NAND_INT, INTC_INT_RISE_EDGE, 0},
 	{ AU1550_USB_DEV_REQ_INT, INTC_INT_HIGH_LEVEL, 0 },
 	{ AU1550_USB_DEV_SUS_INT, INTC_INT_RISE_EDGE, 0 },
@@ -201,14 +201,14 @@ au1xxx_irq_map_t au1xxx_ic0_map[] = {
 	{ AU1200_PSC1_INT, INTC_INT_HIGH_LEVEL, 0},
 	{ AU1200_AES_INT, INTC_INT_HIGH_LEVEL, 0},
 	{ AU1200_CAMERA_INT, INTC_INT_HIGH_LEVEL, 0},
-	{ AU1200_TOY_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1200_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1200_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1200_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
-	{ AU1200_RTC_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1200_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1200_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
-	{ AU1200_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 },
+	{ AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 },
+	{ AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 },
 	{ AU1200_NAND_INT, INTC_INT_RISE_EDGE, 0},
 	{ AU1200_USB_INT, INTC_INT_HIGH_LEVEL, 0 },
 	{ AU1200_LCD_INT, INTC_INT_HIGH_LEVEL, 0},

arch/mips/au1000/common/cputable.c

@@ -37,7 +37,8 @@ struct cpu_spec	cpu_specs[] = {
     { 0xffffffff, 0x02030203, "Au1100 BD", 0, 1 },
     { 0xffffffff, 0x02030204, "Au1100 BE", 0, 1 },
     { 0xffffffff, 0x03030200, "Au1550 AA", 0, 1 },
-    { 0xffffffff, 0x04030200, "Au1200 AA", 0, 1 },
+    { 0xffffffff, 0x04030200, "Au1200 AB", 0, 0 },
+    { 0xffffffff, 0x04030201, "Au1200 AC", 0, 1 },
     { 0x00000000, 0x00000000, "Unknown Au1xxx", 1, 0 },
 };
 

arch/mips/au1000/common/irq.c

@@ -488,7 +488,7 @@ void intc0_req0_irqdispatch(struct pt_regs *regs)
 	intc0_req0 |= au_readl(IC0_REQ0INT);
 
 	if (!intc0_req0) return;
-
+#ifdef AU1000_USB_DEV_REQ_INT
 	/*
 	 * Because of the tight timing of SETUP token to reply
 	 * transactions, the USB devices-side packet complete
@@ -499,7 +499,7 @@ void intc0_req0_irqdispatch(struct pt_regs *regs)
 		do_IRQ(AU1000_USB_DEV_REQ_INT, regs);
 		return;
 	}
-
+#endif
 	irq = au_ffs(intc0_req0) - 1;
 	intc0_req0 &= ~(1<<irq);
 	do_IRQ(irq, regs);

arch/mips/au1000/common/usbdev.c

@@ -1072,7 +1072,6 @@ dma_done_ep0_intr(int irq, void *dev_id, struct pt_regs *regs)
 			clear_dma_done1(ep0->indma);
 
 		pkt = send_packet_complete(ep0);
-		if (pkt)
 		kfree(pkt);
 	}
 
@@ -1302,7 +1301,6 @@ usbdev_exit(void)
 		endpoint_flush(ep);
 	}
 
-	if (usbdev.full_conf_desc)
 	kfree(usbdev.full_conf_desc);
 }
 

arch/mips/au1000/pb1200/Makefile

+#
+# Makefile for the Alchemy Semiconductor PB1200 board.
+#
+
+lib-y := init.o board_setup.o irqmap.o

arch/mips/au1000/pb1200/board_setup.c

+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *	Alchemy Pb1200/Db1200 board setup.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/console.h>
+#include <linux/mc146818rtc.h>
+#include <linux/delay.h>
+
+#if defined(CONFIG_BLK_DEV_IDE_AU1XXX)
+#include <linux/ide.h>
+#endif
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+#include <asm/pgtable.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+
+#ifdef CONFIG_MIPS_PB1200
+#include <asm/mach-pb1x00/pb1200.h>
+#endif
+
+#ifdef CONFIG_MIPS_DB1200
+#include <asm/mach-db1x00/db1200.h>
+#define PB1200_ETH_INT DB1200_ETH_INT
+#define PB1200_IDE_INT DB1200_IDE_INT
+#endif
+
+extern void _board_init_irq(void);
+extern void	(*board_init_irq)(void);
+
+#ifdef CONFIG_BLK_DEV_IDE_AU1XXX
+extern struct ide_ops *ide_ops;
+extern struct ide_ops au1xxx_ide_ops;
+extern u32 au1xxx_ide_virtbase;
+extern u64 au1xxx_ide_physbase;
+extern int au1xxx_ide_irq;
+
+u32 led_base_addr;
+/* Ddma */
+chan_tab_t *ide_read_ch, *ide_write_ch;
+u32 au1xxx_ide_ddma_enable = 0, switch4ddma = 1; // PIO+ddma
+
+dbdev_tab_t new_dbdev_tab_element = { DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 };
+#endif /* end CONFIG_BLK_DEV_IDE_AU1XXX */
+
+void board_reset (void)
+{
+	bcsr->resets = 0;
+}
+
+void __init board_setup(void)
+{
+	char *argptr = NULL;
+	u32 pin_func;
+
+#if 0
+	/* Enable PSC1 SYNC for AC97.  Normaly done in audio driver,
+	 * but it is board specific code, so put it here.
+	 */
+	pin_func = au_readl(SYS_PINFUNC);
+	au_sync();
+	pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+	au_writel(pin_func, SYS_PINFUNC);
+
+	au_writel(0, (u32)bcsr|0x10); /* turn off pcmcia power */
+	au_sync();
+#endif
+
+#if defined( CONFIG_I2C_ALGO_AU1550 )
+	{
+	u32 freq0, clksrc;
+
+	/* Select SMBUS in CPLD */
+	bcsr->resets &= ~(BCSR_RESETS_PCS0MUX);
+
+	pin_func = au_readl(SYS_PINFUNC);
+	au_sync();
+	pin_func &= ~(3<<17 | 1<<4);
+	/* Set GPIOs correctly */
+	pin_func |= 2<<17;
+	au_writel(pin_func, SYS_PINFUNC);
+	au_sync();
+
+	/* The i2c driver depends on 50Mhz clock */
+	freq0 = au_readl(SYS_FREQCTRL0);
+	au_sync();
+	freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+	freq0 |= (3<<SYS_FC_FRDIV1_BIT);
+	/* 396Mhz / (3+1)*2 == 49.5Mhz */
+	au_writel(freq0, SYS_FREQCTRL0);
+	au_sync();
+	freq0 |= SYS_FC_FE1;
+	au_writel(freq0, SYS_FREQCTRL0);
+	au_sync();
+
+	clksrc = au_readl(SYS_CLKSRC);
+	au_sync();
+	clksrc &= ~0x01f00000;
+	/* bit 22 is EXTCLK0 for PSC0 */
+	clksrc |= (0x3 << 22);
+	au_writel(clksrc, SYS_CLKSRC);
+	au_sync();
+	}
+#endif
+
+#ifdef CONFIG_FB_AU1200
+	argptr = prom_getcmdline();
+#ifdef CONFIG_MIPS_PB1200
+	strcat(argptr, " video=au1200fb:panel:s11");
+#endif
+#ifdef CONFIG_MIPS_DB1200
+	strcat(argptr, " video=au1200fb:panel:s7");
+#endif
+#endif
+
+#if defined(CONFIG_BLK_DEV_IDE_AU1XXX)
+	/*
+	 * Iniz IDE parameters
+	 */
+	ide_ops = &au1xxx_ide_ops;
+	au1xxx_ide_irq = PB1200_IDE_INT;
+	au1xxx_ide_physbase = AU1XXX_ATA_PHYS_ADDR;
+	au1xxx_ide_virtbase = KSEG1ADDR(AU1XXX_ATA_PHYS_ADDR);
+	/*
+	 * change PIO or PIO+Ddma
+	 * check the GPIO-5 pin condition. pb1200:s18_dot */
+	switch4ddma = (au_readl(SYS_PINSTATERD) & (1 << 5)) ? 1 : 0;
+#endif
+
+	/* The Pb1200 development board uses external MUX for PSC0 to
+	support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
+	*/
+#if defined(CONFIG_AU1550_PSC_SPI) && defined(CONFIG_I2C_ALGO_AU1550)
+	#error I2C and SPI are mutually exclusive. Both are physically connected to PSC0.\
+			Refer to Pb1200/Db1200 documentation.
+#elif defined( CONFIG_AU1550_PSC_SPI )
+	bcsr->resets |= BCSR_RESETS_PCS0MUX;
+#elif defined( CONFIG_I2C_ALGO_AU1550 )
+	bcsr->resets &= (~BCSR_RESETS_PCS0MUX);
+#endif
+	au_sync();
+
+#ifdef CONFIG_MIPS_PB1200
+	printk("AMD Alchemy Pb1200 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1200
+	printk("AMD Alchemy Db1200 Board\n");
+#endif
+#if 0
+	/* Setup Pb1200 External Interrupt Controller */
+	{
+		extern void (*board_init_irq)(void);
+		extern void _board_init_irq(void);
+		board_init_irq = _board_init_irq;
+	}
+#endif
+}

arch/mips/au1000/pb1200/init.c

+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *	PB1200 board setup
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ *         	ppopov@mvista.com or source@mvista.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/bootmem.h>
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+
+int prom_argc;
+char **prom_argv, **prom_envp;
+extern void  __init prom_init_cmdline(void);
+extern char *prom_getenv(char *envname);
+
+const char *get_system_type(void)
+{
+	return "Alchemy Pb1200";
+}
+
+void __init prom_init(void)
+{
+	unsigned char *memsize_str;
+	unsigned long memsize;
+
+	prom_argc = (int) fw_arg0;
+	prom_argv = (char **) fw_arg1;
+	prom_envp = (char **) fw_arg2;
+
+	mips_machgroup = MACH_GROUP_ALCHEMY;
+	mips_machtype = MACH_PB1200;
+
+	prom_init_cmdline();
+	memsize_str = prom_getenv("memsize");
+	if (!memsize_str) {
+		memsize = 0x08000000;
+	} else {
+		memsize = simple_strtol(memsize_str, NULL, 0);
+	}
+	add_memory_region(0, memsize, BOOT_MEM_RAM);
+}

arch/mips/au1000/pb1200/irqmap.c

+/*
+ * BRIEF MODULE DESCRIPTION
+ *	Au1xxx irq map table
+ *
+ *  This program is free software; you can redistribute	 it and/or modify it
+ *  under  the terms of	 the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
+ *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
+ *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/kernel_stat.h>
+#include <linux/module.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/timex.h>
+#include <linux/slab.h>
+#include <linux/random.h>
+#include <linux/delay.h>
+
+#include <asm/bitops.h>
+#include <asm/bootinfo.h>
+#include <asm/io.h>
+#include <asm/mipsregs.h>
+#include <asm/system.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#ifdef CONFIG_MIPS_PB1200
+#include <asm/mach-pb1x00/pb1200.h>
+#endif
+
+#ifdef CONFIG_MIPS_DB1200
+#include <asm/mach-db1x00/db1200.h>
+#define PB1200_INT_BEGIN DB1200_INT_BEGIN
+#define PB1200_INT_END DB1200_INT_END
+#endif
+
+au1xxx_irq_map_t au1xxx_irq_map[] = {
+	{ AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 }, // This is exteranl interrupt cascade
+};
+
+int au1xxx_nr_irqs = sizeof(au1xxx_irq_map)/sizeof(au1xxx_irq_map_t);
+
+/*
+ *	Support for External interrupts on the PbAu1200 Development platform.
+ */
+static volatile int pb1200_cascade_en=0;
+
+void pb1200_cascade_handler( int irq, void *dev_id, struct pt_regs *regs)
+{
+	unsigned short bisr = bcsr->int_status;
+	int extirq_nr = 0;
+
+	/* Clear all the edge interrupts. This has no effect on level */
+	bcsr->int_status = bisr;
+	for( ; bisr; bisr &= (bisr-1) )
+	{
+		extirq_nr = (PB1200_INT_BEGIN-1) + au_ffs(bisr);
+		/* Ack and dispatch IRQ */
+		do_IRQ(extirq_nr,regs);
+	}
+}
+
+inline void pb1200_enable_irq(unsigned int irq_nr)
+{
+	bcsr->intset_mask = 1<<(irq_nr - PB1200_INT_BEGIN);
+	bcsr->intset = 1<<(irq_nr - PB1200_INT_BEGIN);
+}
+
+inline void pb1200_disable_irq(unsigned int irq_nr)
+{
+	bcsr->intclr_mask = 1<<(irq_nr - PB1200_INT_BEGIN);
+	bcsr->intclr = 1<<(irq_nr - PB1200_INT_BEGIN);
+}
+
+static unsigned int pb1200_startup_irq( unsigned int irq_nr )
+{
+	if (++pb1200_cascade_en == 1)
+	{
+		request_irq(AU1000_GPIO_7, &pb1200_cascade_handler,
+			0, "Pb1200 Cascade", &pb1200_cascade_handler );
+#ifdef CONFIG_MIPS_PB1200
+    /* We have a problem with CPLD rev3. Enable a workaround */
+	if( ((bcsr->whoami & BCSR_WHOAMI_CPLD)>>4) <= 3)
+	{
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("Pb1200 must be at CPLD rev4. Please have Pb1200\n");
+		printk("updated to latest revision. This software will not\n");
+		printk("work on anything less than CPLD rev4\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		printk("\nWARNING!!!\n");
+		while(1);
+	}
+#endif
+	}
+	pb1200_enable_irq(irq_nr);
+	return 0;
+}
+
+static void pb1200_shutdown_irq( unsigned int irq_nr )
+{
+	pb1200_disable_irq(irq_nr);
+	if (--pb1200_cascade_en == 0)
+	{
+		free_irq(AU1000_GPIO_7,&pb1200_cascade_handler );
+	}
+	return;
+}
+
+static inline void pb1200_mask_and_ack_irq(unsigned int irq_nr)
+{
+	pb1200_disable_irq( irq_nr );
+}
+
+static void pb1200_end_irq(unsigned int irq_nr)
+{
+	if (!(irq_desc[irq_nr].status & (IRQ_DISABLED|IRQ_INPROGRESS))) {
+		pb1200_enable_irq(irq_nr);
+	}
+}
+
+static struct hw_interrupt_type external_irq_type =
+{
+#ifdef CONFIG_MIPS_PB1200
+	"Pb1200 Ext",
+#endif
+#ifdef CONFIG_MIPS_DB1200
+	"Db1200 Ext",
+#endif
+	pb1200_startup_irq,
+	pb1200_shutdown_irq,
+	pb1200_enable_irq,
+	pb1200_disable_irq,
+	pb1200_mask_and_ack_irq,
+	pb1200_end_irq,
+	NULL
+};
+
+void _board_init_irq(void)
+{
+	int irq_nr;
+
+	for (irq_nr = PB1200_INT_BEGIN; irq_nr <= PB1200_INT_END; irq_nr++)
+	{
+		irq_desc[irq_nr].handler = &external_irq_type;
+		pb1200_disable_irq(irq_nr);
+	}
+
+	/* GPIO_7 can not be hooked here, so it is hooked upon first
+	request of any source attached to the cascade */
+}
+

arch/mips/kernel/cpu-probe.c

@@ -116,6 +116,8 @@ static inline void check_wait(void)
 	case CPU_AU1000:
 	case CPU_AU1100:
 	case CPU_AU1500:
+	case CPU_AU1550:
+	case CPU_AU1200:
 		if (au1k_wait_ptr != NULL) {
 			cpu_wait = au1k_wait_ptr;
 			printk(" available.\n");
@@ -505,6 +507,9 @@ static inline void cpu_probe_alchemy(struct cpuinfo_mips *c)
 		case 3:
 			c->cputype = CPU_AU1550;
 			break;
+		case 4:
+			c->cputype = CPU_AU1200;
+			break;
 		default:
 			panic("Unknown Au Core!");
 			break;

arch/mips/kernel/proc.c

@@ -60,6 +60,9 @@ static const char *cpu_name[] = {
 	[CPU_TX3927]	"TX3927",
 	[CPU_AU1000]	"Au1000",
 	[CPU_AU1500]	"Au1500",
+	[CPU_AU1100]	"Au1100",
+	[CPU_AU1550]	"Au1550",
+	[CPU_AU1200]	"Au1200",
 	[CPU_4KEC]	"MIPS 4KEc",
 	[CPU_4KSC]	"MIPS 4KSc",
 	[CPU_VR41XX]	"NEC Vr41xx",

arch/mips/mm/c-r4k.c

@@ -1036,7 +1036,11 @@ static void __init probe_pcache(void)
 		c->icache.flags |= MIPS_CACHE_VTAG;
 		break;
 
+	case CPU_AU1000:
 	case CPU_AU1500:
+	case CPU_AU1100:
+	case CPU_AU1550:
+	case CPU_AU1200:
 		c->icache.flags |= MIPS_CACHE_IC_F_DC;
 		break;
 	}

arch/mips/mm/tlbex.c

@@ -840,6 +840,7 @@ static __init void build_tlb_write_entry(u32 **p, struct label **l,
 	case CPU_AU1100:
 	case CPU_AU1500:
 	case CPU_AU1550:
+	case CPU_AU1200:
 		i_nop(p);
 		tlbw(p);
 		break;

include/asm-mips/bootinfo.h

@@ -177,6 +177,8 @@
 #define  MACH_MTX1		7       /* 4G MTX-1 Au1500-based board */
 #define  MACH_PB1550		8       /* Au1550-based eval board */
 #define  MACH_DB1550		9       /* Au1550-based eval board */
+#define  MACH_PB1200		10       /* Au1200-based eval board */
+#define  MACH_DB1200		11       /* Au1200-based eval board */
 
 /*
  * Valid machtype for group NEC_VR41XX

include/asm-mips/cpu.h

@@ -182,7 +182,8 @@
 #define CPU_VR4133		56
 #define CPU_AU1550		57
 #define CPU_24K			58
-#define CPU_LAST		58
+#define CPU_AU1200		59
+#define CPU_LAST		59
 
 /*
  * ISA Level encodings

include/asm-mips/mach-au1x00/au1xxx_dbdma.h

@@ -45,7 +45,7 @@
 #define DDMA_GLOBAL_BASE	0xb4003000
 #define DDMA_CHANNEL_BASE	0xb4002000
 
-typedef struct dbdma_global {
+typedef volatile struct dbdma_global {
 	u32	ddma_config;
 	u32	ddma_intstat;
 	u32	ddma_throttle;
@@ -62,7 +62,7 @@ typedef struct dbdma_global {
 
 /* The structure of a DMA Channel.
 */
-typedef struct au1xxx_dma_channel {
+typedef volatile struct au1xxx_dma_channel {
 	u32	ddma_cfg;	/* See below */
 	u32	ddma_desptr;	/* 32-byte aligned pointer to descriptor */
 	u32	ddma_statptr;	/* word aligned pointer to status word */
@@ -98,7 +98,7 @@ typedef struct au1xxx_dma_channel {
 /* "Standard" DDMA Descriptor.
  * Must be 32-byte aligned.
  */
-typedef struct au1xxx_ddma_desc {
+typedef volatile struct au1xxx_ddma_desc {
 	u32	dscr_cmd0;		/* See below */
 	u32	dscr_cmd1;		/* See below */
 	u32	dscr_source0;		/* source phys address */
@@ -107,6 +107,12 @@ typedef struct au1xxx_ddma_desc {
 	u32	dscr_dest1;		/* See below */
 	u32	dscr_stat;		/* completion status */
 	u32	dscr_nxtptr;		/* Next descriptor pointer (mostly) */
+	/* First 32bytes are HW specific!!!
+	   Lets have some SW data following.. make sure its 32bytes
+	 */
+	u32	sw_status;
+	u32 	sw_context;
+	u32	sw_reserved[6];
 } au1x_ddma_desc_t;
 
 #define DSCR_CMD0_V		(1 << 31)	/* Descriptor valid */
@@ -125,8 +131,11 @@ typedef struct au1xxx_ddma_desc {
 #define DSCR_CMD0_CV		(0x1 << 2)	/* Clear Valid when done */
 #define DSCR_CMD0_ST_MASK	(0x3 << 0)	/* Status instruction */
 
+#define SW_STATUS_INUSE		(1<<0)
+
 /* Command 0 device IDs.
 */
+#ifdef CONFIG_SOC_AU1550
 #define DSCR_CMD0_UART0_TX	0
 #define DSCR_CMD0_UART0_RX	1
 #define DSCR_CMD0_UART3_TX	2
@@ -155,9 +164,45 @@ typedef struct au1xxx_ddma_desc {
 #define DSCR_CMD0_MAC0_TX	25
 #define DSCR_CMD0_MAC1_RX	26
 #define DSCR_CMD0_MAC1_TX	27
+#endif /* CONFIG_SOC_AU1550 */
+
+#ifdef CONFIG_SOC_AU1200
+#define DSCR_CMD0_UART0_TX	0
+#define DSCR_CMD0_UART0_RX	1
+#define DSCR_CMD0_UART1_TX	2
+#define DSCR_CMD0_UART1_RX	3
+#define DSCR_CMD0_DMA_REQ0	4
+#define DSCR_CMD0_DMA_REQ1	5
+#define DSCR_CMD0_MAE_BE	6
+#define DSCR_CMD0_MAE_FE	7
+#define DSCR_CMD0_SDMS_TX0	8
+#define DSCR_CMD0_SDMS_RX0	9
+#define DSCR_CMD0_SDMS_TX1	10
+#define DSCR_CMD0_SDMS_RX1	11
+#define DSCR_CMD0_AES_TX	13
+#define DSCR_CMD0_AES_RX	12
+#define DSCR_CMD0_PSC0_TX	14
+#define DSCR_CMD0_PSC0_RX	15
+#define DSCR_CMD0_PSC1_TX	16
+#define DSCR_CMD0_PSC1_RX	17
+#define DSCR_CMD0_CIM_RXA	18
+#define DSCR_CMD0_CIM_RXB	19
+#define DSCR_CMD0_CIM_RXC	20
+#define DSCR_CMD0_MAE_BOTH	21
+#define DSCR_CMD0_LCD		22
+#define DSCR_CMD0_NAND_FLASH	23
+#define DSCR_CMD0_PSC0_SYNC	24
+#define DSCR_CMD0_PSC1_SYNC	25
+#define DSCR_CMD0_CIM_SYNC	26
+#endif /* CONFIG_SOC_AU1200 */
+
 #define DSCR_CMD0_THROTTLE	30
 #define DSCR_CMD0_ALWAYS	31
 #define DSCR_NDEV_IDS		32
+/* THis macro is used to find/create custom device types */
+#define DSCR_DEV2CUSTOM_ID(x,d)	(((((x)&0xFFFF)<<8)|0x32000000)|((d)&0xFF))
+#define DSCR_CUSTOM2DEV_ID(x)	((x)&0xFF)
+
 
 #define DSCR_CMD0_SID(x)	(((x) & 0x1f) << 25)
 #define DSCR_CMD0_DID(x)	(((x) & 0x1f) << 20)
@@ -246,6 +291,43 @@ typedef struct au1xxx_ddma_desc {
 */
 #define NUM_DBDMA_CHANS	16
 
+/*
+ * Ddma API definitions
+ * FIXME: may not fit to this header file
+ */
+typedef struct dbdma_device_table {
+	u32		dev_id;
+	u32		dev_flags;
+	u32		dev_tsize;
+	u32		dev_devwidth;
+	u32		dev_physaddr;		/* If FIFO */
+	u32		dev_intlevel;
+	u32		dev_intpolarity;
+} dbdev_tab_t;
+
+
+typedef struct dbdma_chan_config {
+	spinlock_t      lock;
+
+	u32			chan_flags;
+	u32			chan_index;
+	dbdev_tab_t		*chan_src;
+	dbdev_tab_t		*chan_dest;
+	au1x_dma_chan_t		*chan_ptr;
+	au1x_ddma_desc_t	*chan_desc_base;
+	au1x_ddma_desc_t	*get_ptr, *put_ptr, *cur_ptr;
+	void			*chan_callparam;
+	void (*chan_callback)(int, void *, struct pt_regs *);
+} chan_tab_t;
+
+#define DEV_FLAGS_INUSE		(1 << 0)
+#define DEV_FLAGS_ANYUSE	(1 << 1)
+#define DEV_FLAGS_OUT		(1 << 2)
+#define DEV_FLAGS_IN		(1 << 3)
+#define DEV_FLAGS_BURSTABLE (1 << 4)
+#define DEV_FLAGS_SYNC		(1 << 5)
+/* end Ddma API definitions */
+
 /* External functions for drivers to use.
 */
 /* Use this to allocate a dbdma channel.  The device ids are one of the
@@ -258,18 +340,6 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
 
 #define DBDMA_MEM_CHAN	DSCR_CMD0_ALWAYS
 
-/* ACK!  These should be in a board specific description file.
-*/
-#ifdef CONFIG_MIPS_PB1550
-#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
-#endif
-#ifdef CONFIG_MIPS_DB1550
-#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
-#endif
-
-
 /* Set the device width of a in/out fifo.
 */
 u32 au1xxx_dbdma_set_devwidth(u32 chanid, int bits);
@@ -280,8 +350,8 @@ u32 au1xxx_dbdma_ring_alloc(u32 chanid, int entries);
 
 /* Put buffers on source/destination descriptors.
 */
-u32 au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes);
-u32 au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes);
+u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags);
+u32 _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags);
 
 /* Get a buffer from the destination descriptor.
 */
@@ -295,5 +365,25 @@ u32 au1xxx_get_dma_residue(u32 chanid);
 void au1xxx_dbdma_chan_free(u32 chanid);
 void au1xxx_dbdma_dump(u32 chanid);
 
+u32 au1xxx_dbdma_put_dscr(u32 chanid, au1x_ddma_desc_t *dscr );
+
+u32 au1xxx_ddma_add_device( dbdev_tab_t *dev );
+
+/*
+ 	Some compatibilty macros --
+		Needed to make changes to API without breaking existing drivers
+*/
+#define	au1xxx_dbdma_put_source(chanid,buf,nbytes)_au1xxx_dbdma_put_source(chanid, buf, nbytes, DDMA_FLAGS_IE)
+#define	au1xxx_dbdma_put_source_flags(chanid,buf,nbytes,flags) _au1xxx_dbdma_put_source(chanid, buf, nbytes, flags)
+
+#define au1xxx_dbdma_put_dest(chanid,buf,nbytes) _au1xxx_dbdma_put_dest(chanid, buf, nbytes, DDMA_FLAGS_IE)
+#define	au1xxx_dbdma_put_dest_flags(chanid,buf,nbytes,flags) _au1xxx_dbdma_put_dest(chanid, buf, nbytes, flags)
+
+/*
+ *	Flags for the put_source/put_dest functions.
+ */
+#define DDMA_FLAGS_IE	(1<<0)
+#define DDMA_FLAGS_NOIE (1<<1)
+
 #endif /* _LANGUAGE_ASSEMBLY */
 #endif /* _AU1000_DBDMA_H_ */

include/asm-mips/mach-db1x00/db1200.h

+/*
+ * AMD Alchemy DB1200 Referrence Board
+ * Board Registers defines.
+ *
+ * ########################################################################
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ *
+ */
+#ifndef __ASM_DB1200_H
+#define __ASM_DB1200_H
+
+#include <linux/types.h>
+
+// This is defined in au1000.h with bogus value
+#undef AU1X00_EXTERNAL_INT
+
+#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
+#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
+#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC1_TX
+#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC1_RX
+
+/* SPI and SMB are muxed on the Pb1200 board.
+   Refer to board documentation.
+ */
+#define SPI_PSC_BASE        PSC0_BASE_ADDR
+#define SMBUS_PSC_BASE      PSC0_BASE_ADDR
+/* AC97 and I2S are muxed on the Pb1200 board.
+   Refer to board documentation.
+ */
+#define AC97_PSC_BASE       PSC1_BASE_ADDR
+#define I2S_PSC_BASE		PSC1_BASE_ADDR
+
+#define BCSR_KSEG1_ADDR 0xB9800000
+
+typedef volatile struct
+{
+	/*00*/	u16 whoami;
+		u16 reserved0;
+	/*04*/	u16 status;
+		u16 reserved1;
+	/*08*/	u16 switches;
+		u16 reserved2;
+	/*0C*/	u16 resets;
+		u16 reserved3;
+
+	/*10*/	u16 pcmcia;
+		u16 reserved4;
+	/*14*/	u16 board;
+		u16 reserved5;
+	/*18*/	u16 disk_leds;
+		u16 reserved6;
+	/*1C*/	u16 system;
+		u16 reserved7;
+
+	/*20*/	u16 intclr;
+		u16 reserved8;
+	/*24*/	u16 intset;
+		u16 reserved9;
+	/*28*/	u16 intclr_mask;
+		u16 reserved10;
+	/*2C*/	u16 intset_mask;
+		u16 reserved11;
+
+	/*30*/	u16 sig_status;
+		u16 reserved12;
+	/*34*/	u16 int_status;
+		u16 reserved13;
+	/*38*/	u16 reserved14;
+		u16 reserved15;
+	/*3C*/	u16 reserved16;
+		u16 reserved17;
+
+} BCSR;
+
+static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+/*
+ * Register bit definitions for the BCSRs
+ */
+#define BCSR_WHOAMI_DCID	0x000F
+#define BCSR_WHOAMI_CPLD	0x00F0
+#define BCSR_WHOAMI_BOARD	0x0F00
+
+#define BCSR_STATUS_PCMCIA0VS	0x0003
+#define BCSR_STATUS_PCMCIA1VS	0x000C
+#define BCSR_STATUS_SWAPBOOT	0x0040
+#define BCSR_STATUS_FLASHBUSY	0x0100
+#define BCSR_STATUS_IDECBLID	0x0200
+#define BCSR_STATUS_SD0WP		0x0400
+#define BCSR_STATUS_U0RXD		0x1000
+#define BCSR_STATUS_U1RXD		0x2000
+
+#define BCSR_SWITCHES_OCTAL	0x00FF
+#define BCSR_SWITCHES_DIP_1	0x0080
+#define BCSR_SWITCHES_DIP_2	0x0040
+#define BCSR_SWITCHES_DIP_3	0x0020
+#define BCSR_SWITCHES_DIP_4	0x0010
+#define BCSR_SWITCHES_DIP_5	0x0008
+#define BCSR_SWITCHES_DIP_6	0x0004
+#define BCSR_SWITCHES_DIP_7	0x0002
+#define BCSR_SWITCHES_DIP_8	0x0001
+#define BCSR_SWITCHES_ROTARY	0x0F00
+
+#define BCSR_RESETS_ETH		0x0001
+#define BCSR_RESETS_CAMERA	0x0002
+#define BCSR_RESETS_DC		0x0004
+#define BCSR_RESETS_IDE		0x0008
+#define BCSR_RESETS_TV		0x0010
+/* not resets but in the same register */
+#define BCSR_RESETS_PWMR1mUX 0x0800
+#define BCSR_RESETS_PCS0MUX	0x1000
+#define BCSR_RESETS_PCS1MUX	0x2000
+#define BCSR_RESETS_SPISEL	0x4000
+
+#define BCSR_PCMCIA_PC0VPP	0x0003
+#define BCSR_PCMCIA_PC0VCC	0x000C
+#define BCSR_PCMCIA_PC0DRVEN	0x0010
+#define BCSR_PCMCIA_PC0RST	0x0080
+#define BCSR_PCMCIA_PC1VPP	0x0300
+#define BCSR_PCMCIA_PC1VCC	0x0C00
+#define BCSR_PCMCIA_PC1DRVEN	0x1000
+#define BCSR_PCMCIA_PC1RST	0x8000
+
+#define BCSR_BOARD_LCDVEE	0x0001
+#define BCSR_BOARD_LCDVDD	0x0002
+#define BCSR_BOARD_LCDBL	0x0004
+#define BCSR_BOARD_CAMSNAP	0x0010
+#define BCSR_BOARD_CAMPWR	0x0020
+#define BCSR_BOARD_SD0PWR	0x0040
+
+#define BCSR_LEDS_DECIMALS	0x0003
+#define BCSR_LEDS_LED0		0x0100
+#define BCSR_LEDS_LED1		0x0200
+#define BCSR_LEDS_LED2		0x0400
+#define BCSR_LEDS_LED3		0x0800
+
+#define BCSR_SYSTEM_POWEROFF	0x4000
+#define BCSR_SYSTEM_RESET	0x8000
+
+/* Bit positions for the different interrupt sources */
+#define BCSR_INT_IDE		0x0001
+#define BCSR_INT_ETH		0x0002
+#define BCSR_INT_PC0		0x0004
+#define BCSR_INT_PC0STSCHG	0x0008
+#define BCSR_INT_PC1		0x0010
+#define BCSR_INT_PC1STSCHG	0x0020
+#define BCSR_INT_DC			0x0040
+#define BCSR_INT_FLASHBUSY	0x0080
+#define BCSR_INT_PC0INSERT	0x0100
+#define BCSR_INT_PC0EJECT	0x0200
+#define BCSR_INT_PC1INSERT	0x0400
+#define BCSR_INT_PC1EJECT	0x0800
+#define BCSR_INT_SD0INSERT	0x1000
+#define BCSR_INT_SD0EJECT	0x2000
+
+#define AU1XXX_SMC91111_PHYS_ADDR	(0x19000300)
+#define AU1XXX_SMC91111_IRQ			DB1200_ETH_INT
+
+#define AU1XXX_ATA_PHYS_ADDR		(0x18800000)
+#define AU1XXX_ATA_PHYS_LEN			(0x100)
+#define AU1XXX_ATA_REG_OFFSET	(5)
+#define AU1XXX_ATA_INT			DB1200_IDE_INT
+#define AU1XXX_ATA_DDMA_REQ		DSCR_CMD0_DMA_REQ1;
+#define AU1XXX_ATA_RQSIZE		128
+
+#define NAND_PHYS_ADDR   0x20000000
+
+/*
+ *	External Interrupts for Pb1200 as of 8/6/2004.
+ *   Bit positions in the CPLD registers can be calculated by taking
+ *   the interrupt define and subtracting the DB1200_INT_BEGIN value.
+ *    *example: IDE bis pos is  = 64 - 64
+                ETH bit pos is  = 65 - 64
+ */
+#define DB1200_INT_BEGIN		(AU1000_LAST_INTC1_INT + 1)
+#define DB1200_IDE_INT			(DB1200_INT_BEGIN + 0)
+#define DB1200_ETH_INT			(DB1200_INT_BEGIN + 1)
+#define DB1200_PC0_INT			(DB1200_INT_BEGIN + 2)
+#define DB1200_PC0_STSCHG_INT	(DB1200_INT_BEGIN + 3)
+#define DB1200_PC1_INT			(DB1200_INT_BEGIN + 4)
+#define DB1200_PC1_STSCHG_INT	(DB1200_INT_BEGIN + 5)
+#define DB1200_DC_INT			(DB1200_INT_BEGIN + 6)
+#define DB1200_FLASHBUSY_INT	(DB1200_INT_BEGIN + 7)
+#define DB1200_PC0_INSERT_INT	(DB1200_INT_BEGIN + 8)
+#define DB1200_PC0_EJECT_INT	(DB1200_INT_BEGIN + 9)
+#define DB1200_PC1_INSERT_INT	(DB1200_INT_BEGIN + 10)
+#define DB1200_PC1_EJECT_INT	(DB1200_INT_BEGIN + 11)
+#define DB1200_SD0_INSERT_INT	(DB1200_INT_BEGIN + 12)
+#define DB1200_SD0_EJECT_INT	(DB1200_INT_BEGIN + 13)
+
+#define DB1200_INT_END			(DB1200_INT_BEGIN + 15)
+
+/* For drivers/pcmcia/au1000_db1x00.c */
+#define BOARD_PC0_INT DB1200_PC0_INT
+#define BOARD_PC1_INT DB1200_PC1_INT
+#define BOARD_CARD_INSERTED(SOCKET) bcsr->sig_status & (1<<(8+(2*SOCKET)))
+
+#endif /* __ASM_DB1200_H */
+

include/asm-mips/mach-pb1x00/pb1200.h

+/*
+ * AMD Alchemy PB1200 Referrence Board
+ * Board Registers defines.
+ *
+ * ########################################################################
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ *
+ */
+#ifndef __ASM_PB1200_H
+#define __ASM_PB1200_H
+
+#include <linux/types.h>
+
+// This is defined in au1000.h with bogus value
+#undef AU1X00_EXTERNAL_INT
+
+#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
+#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
+#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC1_TX
+#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC1_RX
+
+/* SPI and SMB are muxed on the Pb1200 board.
+   Refer to board documentation.
+ */
+#define SPI_PSC_BASE        PSC0_BASE_ADDR
+#define SMBUS_PSC_BASE      PSC0_BASE_ADDR
+/* AC97 and I2S are muxed on the Pb1200 board.
+   Refer to board documentation.
+ */
+#define AC97_PSC_BASE       PSC1_BASE_ADDR
+#define I2S_PSC_BASE		PSC1_BASE_ADDR
+
+#define BCSR_KSEG1_ADDR 0xAD800000
+
+typedef volatile struct
+{
+	/*00*/	u16 whoami;
+		u16 reserved0;
+	/*04*/	u16 status;
+		u16 reserved1;
+	/*08*/	u16 switches;
+		u16 reserved2;
+	/*0C*/	u16 resets;
+		u16 reserved3;
+
+	/*10*/	u16 pcmcia;
+		u16 reserved4;
+	/*14*/	u16 board;
+		u16 reserved5;
+	/*18*/	u16 disk_leds;
+		u16 reserved6;
+	/*1C*/	u16 system;
+		u16 reserved7;
+
+	/*20*/	u16 intclr;
+		u16 reserved8;
+	/*24*/	u16 intset;
+		u16 reserved9;
+	/*28*/	u16 intclr_mask;
+		u16 reserved10;
+	/*2C*/	u16 intset_mask;
+		u16 reserved11;
+
+	/*30*/	u16 sig_status;
+		u16 reserved12;
+	/*34*/	u16 int_status;
+		u16 reserved13;
+	/*38*/	u16 reserved14;
+		u16 reserved15;
+	/*3C*/	u16 reserved16;
+		u16 reserved17;
+
+} BCSR;
+
+static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+/*
+ * Register bit definitions for the BCSRs
+ */
+#define BCSR_WHOAMI_DCID	0x000F
+#define BCSR_WHOAMI_CPLD	0x00F0
+#define BCSR_WHOAMI_BOARD	0x0F00
+
+#define BCSR_STATUS_PCMCIA0VS	0x0003
+#define BCSR_STATUS_PCMCIA1VS	0x000C
+#define BCSR_STATUS_SWAPBOOT	0x0040
+#define BCSR_STATUS_FLASHBUSY	0x0100
+#define BCSR_STATUS_IDECBLID	0x0200
+#define BCSR_STATUS_SD0WP		0x0400
+#define BCSR_STATUS_SD1WP		0x0800
+#define BCSR_STATUS_U0RXD		0x1000
+#define BCSR_STATUS_U1RXD		0x2000
+
+#define BCSR_SWITCHES_OCTAL	0x00FF
+#define BCSR_SWITCHES_DIP_1	0x0080
+#define BCSR_SWITCHES_DIP_2	0x0040
+#define BCSR_SWITCHES_DIP_3	0x0020
+#define BCSR_SWITCHES_DIP_4	0x0010
+#define BCSR_SWITCHES_DIP_5	0x0008
+#define BCSR_SWITCHES_DIP_6	0x0004
+#define BCSR_SWITCHES_DIP_7	0x0002
+#define BCSR_SWITCHES_DIP_8	0x0001
+#define BCSR_SWITCHES_ROTARY	0x0F00
+
+#define BCSR_RESETS_ETH		0x0001
+#define BCSR_RESETS_CAMERA	0x0002
+#define BCSR_RESETS_DC		0x0004
+#define BCSR_RESETS_IDE		0x0008
+/* not resets but in the same register */
+#define BCSR_RESETS_WSCFSM  0x0800
+#define BCSR_RESETS_PCS0MUX	0x1000
+#define BCSR_RESETS_PCS1MUX	0x2000
+#define BCSR_RESETS_SPISEL	0x4000
+#define BCSR_RESETS_SD1MUX  0x8000
+
+#define BCSR_PCMCIA_PC0VPP	0x0003
+#define BCSR_PCMCIA_PC0VCC	0x000C
+#define BCSR_PCMCIA_PC0DRVEN	0x0010
+#define BCSR_PCMCIA_PC0RST	0x0080
+#define BCSR_PCMCIA_PC1VPP	0x0300
+#define BCSR_PCMCIA_PC1VCC	0x0C00
+#define BCSR_PCMCIA_PC1DRVEN	0x1000
+#define BCSR_PCMCIA_PC1RST	0x8000
+
+#define BCSR_BOARD_LCDVEE	0x0001
+#define BCSR_BOARD_LCDVDD	0x0002
+#define BCSR_BOARD_LCDBL	0x0004
+#define BCSR_BOARD_CAMSNAP	0x0010
+#define BCSR_BOARD_CAMPWR	0x0020
+#define BCSR_BOARD_SD0PWR	0x0040
+#define BCSR_BOARD_SD1PWR	0x0080
+
+#define BCSR_LEDS_DECIMALS	0x00FF
+#define BCSR_LEDS_LED0		0x0100
+#define BCSR_LEDS_LED1		0x0200
+#define BCSR_LEDS_LED2		0x0400
+#define BCSR_LEDS_LED3		0x0800
+
+#define BCSR_SYSTEM_VDDI	0x001F
+#define BCSR_SYSTEM_POWEROFF	0x4000
+#define BCSR_SYSTEM_RESET	0x8000
+
+/* Bit positions for the different interrupt sources */
+#define BCSR_INT_IDE		0x0001
+#define BCSR_INT_ETH		0x0002
+#define BCSR_INT_PC0		0x0004
+#define BCSR_INT_PC0STSCHG	0x0008
+#define BCSR_INT_PC1		0x0010
+#define BCSR_INT_PC1STSCHG	0x0020
+#define BCSR_INT_DC			0x0040
+#define BCSR_INT_FLASHBUSY	0x0080
+#define BCSR_INT_PC0INSERT	0x0100
+#define BCSR_INT_PC0EJECT	0x0200
+#define BCSR_INT_PC1INSERT	0x0400
+#define BCSR_INT_PC1EJECT	0x0800
+#define BCSR_INT_SD0INSERT	0x1000
+#define BCSR_INT_SD0EJECT	0x2000
+#define BCSR_INT_SD1INSERT	0x4000
+#define BCSR_INT_SD1EJECT	0x8000
+
+#define AU1XXX_SMC91111_PHYS_ADDR	(0x0D000300)
+#define AU1XXX_SMC91111_IRQ			PB1200_ETH_INT
+
+#define AU1XXX_ATA_PHYS_ADDR		(0x0C800000)
+#define AU1XXX_ATA_PHYS_LEN			(0x100)
+#define AU1XXX_ATA_REG_OFFSET	(5)
+#define AU1XXX_ATA_INT			PB1200_IDE_INT
+#define AU1XXX_ATA_DDMA_REQ		DSCR_CMD0_DMA_REQ1;
+#define AU1XXX_ATA_RQSIZE		128
+
+#define NAND_PHYS_ADDR   0x1C000000
+
+/* Timing values as described in databook, * ns value stripped of
+ * lower 2 bits.
+ * These defines are here rather than an SOC1200 generic file because
+ * the parts chosen on another board may be different and may require
+ * different timings.
+ */
+#define NAND_T_H			(18 >> 2)
+#define NAND_T_PUL			(30 >> 2)
+#define NAND_T_SU			(30 >> 2)
+#define NAND_T_WH			(30 >> 2)
+
+/* Bitfield shift amounts */
+#define NAND_T_H_SHIFT		0
+#define NAND_T_PUL_SHIFT	4
+#define NAND_T_SU_SHIFT		8
+#define NAND_T_WH_SHIFT		12
+
+#define NAND_TIMING	((NAND_T_H   & 0xF)	<< NAND_T_H_SHIFT)   | \
+			((NAND_T_PUL & 0xF)	<< NAND_T_PUL_SHIFT) | \
+			((NAND_T_SU  & 0xF)	<< NAND_T_SU_SHIFT)  | \
+			((NAND_T_WH  & 0xF)	<< NAND_T_WH_SHIFT)
+
+
+/*
+ *	External Interrupts for Pb1200 as of 8/6/2004.
+ *   Bit positions in the CPLD registers can be calculated by taking
+ *   the interrupt define and subtracting the PB1200_INT_BEGIN value.
+ *    *example: IDE bis pos is  = 64 - 64
+                ETH bit pos is  = 65 - 64
+ */
+#define PB1200_INT_BEGIN		(AU1000_LAST_INTC1_INT + 1)
+#define PB1200_IDE_INT			(PB1200_INT_BEGIN + 0)
+#define PB1200_ETH_INT			(PB1200_INT_BEGIN + 1)
+#define PB1200_PC0_INT			(PB1200_INT_BEGIN + 2)
+#define PB1200_PC0_STSCHG_INT	(PB1200_INT_BEGIN + 3)
+#define PB1200_PC1_INT			(PB1200_INT_BEGIN + 4)
+#define PB1200_PC1_STSCHG_INT	(PB1200_INT_BEGIN + 5)
+#define PB1200_DC_INT			(PB1200_INT_BEGIN + 6)
+#define PB1200_FLASHBUSY_INT	(PB1200_INT_BEGIN + 7)
+#define PB1200_PC0_INSERT_INT	(PB1200_INT_BEGIN + 8)
+#define PB1200_PC0_EJECT_INT	(PB1200_INT_BEGIN + 9)
+#define PB1200_PC1_INSERT_INT	(PB1200_INT_BEGIN + 10)
+#define PB1200_PC1_EJECT_INT	(PB1200_INT_BEGIN + 11)
+#define PB1200_SD0_INSERT_INT	(PB1200_INT_BEGIN + 12)
+#define PB1200_SD0_EJECT_INT	(PB1200_INT_BEGIN + 13)
+#define PB1200_SD1_INSERT_INT	(PB1200_INT_BEGIN + 14)
+#define PB1200_SD1_EJECT_INT	(PB1200_INT_BEGIN + 15)
+
+#define PB1200_INT_END			(PB1200_INT_BEGIN + 15)
+
+/* For drivers/pcmcia/au1000_db1x00.c */
+#define BOARD_PC0_INT PB1200_PC0_INT
+#define BOARD_PC1_INT PB1200_PC1_INT
+#define BOARD_CARD_INSERTED(SOCKET) bcsr->sig_status & (1<<(8+(2*SOCKET)))
+
+#endif /* __ASM_PB1200_H */
+