Commit e5ee1281 authored by Maxime Ripard's avatar Maxime Ripard Committed by Andrew Lunn

ARM: mvebu: Add Armada 385 Access Point Development Board support

The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB
SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage.

[gregory.clement@free-electrons.com: switch the license to the dual
X11/GPL with the agreement of the author]
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: default avatarGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
parent 91b4c91f
......@@ -536,6 +536,7 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \
armada-375-db.dtb
dtb-$(CONFIG_MACH_ARMADA_38X) += \
armada-385-db.dtb \
armada-385-db-ap.dtb \
armada-385-rd.dtb
dtb-$(CONFIG_MACH_ARMADA_XP) += \
armada-xp-axpwifiap.dtb \
......
/*
* Device Tree file for Marvell Armada 385 Access Point Development board
* (DB-88F6820-AP)
*
* Copyright (C) 2014 Marvell
*
* Nadav Haklai <nadavh@marvell.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without
* any warranty of any kind, whether express or implied.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "armada-385.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Marvell Armada 385 Access Point Development Board";
compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x";
chosen {
bootargs = "console=ttyS0,115200";
stdout-path = &uart1;
};
memory {
device_type = "memory";
reg = <0x00000000 0x80000000>; /* 2GB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
internal-regs {
spi1: spi@10680 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins>;
status = "okay";
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,m25p128";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <54000000>;
};
};
i2c0: i2c@11000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
/*
* This bus is wired to two EEPROM
* sockets, one of which holding the
* board ID used by the bootloader.
* Erasing this EEPROM's content will
* brick the board.
* Use this bus with caution.
*/
};
mdio@72004 {
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>;
phy0: ethernet-phy@1 {
reg = <1>;
};
phy1: ethernet-phy@4 {
reg = <4>;
};
phy2: ethernet-phy@6 {
reg = <6>;
};
};
/* UART0 is exposed through the JP8 connector */
uart0: serial@12000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
/*
* UART1 is exposed through a FTDI chip
* wired to the mini-USB connector
*/
uart1: serial@12100 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "okay";
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
};
ethernet@34000 {
status = "okay";
phy = <&phy1>;
phy-mode = "sgmii";
};
ethernet@70000 {
pinctrl-names = "default";
/*
* The Reference Clock 0 is used to
* provide a clock to the PHY
*/
pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
};
};
pcie-controller {
status = "okay";
/*
* The three PCIe units are accessible through
* standard mini-PCIe slots on the board.
*/
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
pcie@2,0 {
/* Port 1, Lane 0 */
status = "okay";
};
pcie@3,0 {
/* Port 2, Lane 0 */
status = "okay";
};
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment