ARM: dts: sun8i: a23/a33: Provide default muxing for relevant controllers

The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

arch/arm/boot/dts/sun8i-a23-a33.dtsi

@@ -169,6 +169,8 @@ mmc0: mmc@1c0f000 {
 			resets = <&ccu RST_BUS_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -499,6 +501,8 @@ i2c0: i2c@1c2ac00 {
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C0>;
 			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -510,6 +514,8 @@ i2c1: i2c@1c2b000 {
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C1>;
 			resets = <&ccu RST_BUS_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -521,6 +527,8 @@ i2c2: i2c@1c2b400 {
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C2>;
 			resets = <&ccu RST_BUS_I2C2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm/boot/dts/sun8i-a23-evb.dts

@@ -65,14 +65,10 @@ chosen {
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
 	status = "okay";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 };
 
@@ -103,8 +99,6 @@ button-600 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */

arch/arm/boot/dts/sun8i-a33-olinuxino.dts

@@ -82,8 +82,6 @@ &ehci0 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */

arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts

@@ -140,8 +140,6 @@ button-600 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */

arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts

@@ -126,28 +126,20 @@ &ehci0 {
 
 /* This is the i2c bus exposed on the DSI connector for the touch panel */
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
 	status = "disabled";
 };
 
 /* This is the i2c bus exposed on the GPIO header */
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "disabled";
 };
 
 /* This is the i2c bus exposed on the CSI connector to control the sensor */
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	status = "disabled";
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */

arch/arm/boot/dts/sun8i-r16-parrot.dts

@@ -95,8 +95,6 @@ &ehci0 {
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 
 	/*
@@ -126,8 +124,6 @@ button-390 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
 	bus-width = <4>;

arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi

@@ -80,8 +80,6 @@ touchscreen: touchscreen@40 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */