Merge remote-tracking branches 'asoc/topic/bcm2835', 'asoc/topic/cs42l56' and...

Merge remote-tracking branches 'asoc/topic/bcm2835', 'asoc/topic/cs42l56' and 'asoc/topic/cs43130' into asoc-next

Documentation/devicetree/bindings/sound/cs42l56.txt

@@ -55,7 +55,7 @@ Example:
 codec: codec@4b {
 	compatible = "cirrus,cs42l56";
 	reg = <0x4b>;
-	gpio-reset = <&gpio 10 0>;
+	cirrus,gpio-nreset = <&gpio 10 0>;
 	cirrus,chgfreq-divisor = <0x05>;
 	cirrus.ain1_ref_cfg;
 	cirrus,micbias-lvl = <5>;

sound/soc/bcm/bcm2835-i2s.c

@@ -31,6 +31,7 @@
  * General Public License for more details.
  */
 
+#include <linux/bitops.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/device.h>
@@ -99,6 +100,8 @@
 #define BCM2835_I2S_CHWID(v)		(v)
 #define BCM2835_I2S_CH1(v)		((v) << 16)
 #define BCM2835_I2S_CH2(v)		(v)
+#define BCM2835_I2S_CH1_POS(v)		BCM2835_I2S_CH1(BCM2835_I2S_CHPOS(v))
+#define BCM2835_I2S_CH2_POS(v)		BCM2835_I2S_CH2(BCM2835_I2S_CHPOS(v))
 
 #define BCM2835_I2S_TX_PANIC(v)	((v) << 24)
 #define BCM2835_I2S_RX_PANIC(v)	((v) << 16)
@@ -110,12 +113,19 @@
 #define BCM2835_I2S_INT_RXR		BIT(1)
 #define BCM2835_I2S_INT_TXW		BIT(0)
 
+/* Frame length register is 10 bit, maximum length 1024 */
+#define BCM2835_I2S_MAX_FRAME_LENGTH	1024
+
 /* General device struct */
 struct bcm2835_i2s_dev {
 	struct device				*dev;
 	struct snd_dmaengine_dai_dma_data	dma_data[2];
 	unsigned int				fmt;
-	unsigned int				bclk_ratio;
+	unsigned int				tdm_slots;
+	unsigned int				rx_mask;
+	unsigned int				tx_mask;
+	unsigned int				slot_width;
+	unsigned int				frame_length;
 
 	struct regmap				*i2s_regmap;
 	struct clk				*clk;
@@ -225,19 +235,120 @@ static int bcm2835_i2s_set_dai_bclk_ratio(struct snd_soc_dai *dai,
 				      unsigned int ratio)
 {
 	struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai);
-	dev->bclk_ratio = ratio;
+
+	if (!ratio) {
+		dev->tdm_slots = 0;
+		return 0;
+	}
+
+	if (ratio > BCM2835_I2S_MAX_FRAME_LENGTH)
+		return -EINVAL;
+
+	dev->tdm_slots = 2;
+	dev->rx_mask = 0x03;
+	dev->tx_mask = 0x03;
+	dev->slot_width = ratio / 2;
+	dev->frame_length = ratio;
+
 	return 0;
 }
 
+static int bcm2835_i2s_set_dai_tdm_slot(struct snd_soc_dai *dai,
+	unsigned int tx_mask, unsigned int rx_mask,
+	int slots, int width)
+{
+	struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai);
+
+	if (slots) {
+		if (slots < 0 || width < 0)
+			return -EINVAL;
+
+		/* Limit masks to available slots */
+		rx_mask &= GENMASK(slots - 1, 0);
+		tx_mask &= GENMASK(slots - 1, 0);
+
+		/*
+		 * The driver is limited to 2-channel setups.
+		 * Check that exactly 2 bits are set in the masks.
+		 */
+		if (hweight_long((unsigned long) rx_mask) != 2
+		    || hweight_long((unsigned long) tx_mask) != 2)
+			return -EINVAL;
+
+		if (slots * width > BCM2835_I2S_MAX_FRAME_LENGTH)
+			return -EINVAL;
+	}
+
+	dev->tdm_slots = slots;
+
+	dev->rx_mask = rx_mask;
+	dev->tx_mask = tx_mask;
+	dev->slot_width = width;
+	dev->frame_length = slots * width;
+
+	return 0;
+}
+
+/*
+ * Convert logical slot number into physical slot number.
+ *
+ * If odd_offset is 0 sequential number is identical to logical number.
+ * This is used for DSP modes with slot numbering 0 1 2 3 ...
+ *
+ * Otherwise odd_offset defines the physical offset for odd numbered
+ * slots. This is used for I2S and left/right justified modes to
+ * translate from logical slot numbers 0 1 2 3 ... into physical slot
+ * numbers 0 2 ... 3 4 ...
+ */
+static int bcm2835_i2s_convert_slot(unsigned int slot, unsigned int odd_offset)
+{
+	if (!odd_offset)
+		return slot;
+
+	if (slot & 1)
+		return (slot >> 1) + odd_offset;
+
+	return slot >> 1;
+}
+
+/*
+ * Calculate channel position from mask and slot width.
+ *
+ * Mask must contain exactly 2 set bits.
+ * Lowest set bit is channel 1 position, highest set bit channel 2.
+ * The constant offset is added to both channel positions.
+ *
+ * If odd_offset is > 0 slot positions are translated to
+ * I2S-style TDM slot numbering ( 0 2 ... 3 4 ...) with odd
+ * logical slot numbers starting at physical slot odd_offset.
+ */
+static void bcm2835_i2s_calc_channel_pos(
+	unsigned int *ch1_pos, unsigned int *ch2_pos,
+	unsigned int mask, unsigned int width,
+	unsigned int bit_offset, unsigned int odd_offset)
+{
+	*ch1_pos = bcm2835_i2s_convert_slot((ffs(mask) - 1), odd_offset)
+			* width + bit_offset;
+	*ch2_pos = bcm2835_i2s_convert_slot((fls(mask) - 1), odd_offset)
+			* width + bit_offset;
+}
+
 static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
 				 struct snd_pcm_hw_params *params,
 				 struct snd_soc_dai *dai)
 {
 	struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai);
-	unsigned int sampling_rate = params_rate(params);
-	unsigned int data_length, data_delay, bclk_ratio;
-	unsigned int ch1pos, ch2pos, mode, format;
+	unsigned int data_length, data_delay, framesync_length;
+	unsigned int slots, slot_width, odd_slot_offset;
+	int frame_length, bclk_rate;
+	unsigned int rx_mask, tx_mask;
+	unsigned int rx_ch1_pos, rx_ch2_pos, tx_ch1_pos, tx_ch2_pos;
+	unsigned int mode, format;
+	bool bit_clock_master = false;
+	bool frame_sync_master = false;
+	bool frame_start_falling_edge = false;
 	uint32_t csreg;
+	int ret = 0;
 
 	/*
 	 * If a stream is already enabled,
@@ -248,42 +359,70 @@ static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
 	if (csreg & (BCM2835_I2S_TXON | BCM2835_I2S_RXON))
 		return 0;
 
-	/*
-	 * Adjust the data length according to the format.
-	 * We prefill the half frame length with an integer
-	 * divider of 2400 as explained at the clock settings.
-	 * Maybe it is overwritten there, if the Integer mode
-	 * does not apply.
-	 */
-	switch (params_format(params)) {
-	case SNDRV_PCM_FORMAT_S16_LE:
-		data_length = 16;
-		break;
-	case SNDRV_PCM_FORMAT_S24_LE:
-		data_length = 24;
+	data_length = params_width(params);
+	data_delay = 0;
+	odd_slot_offset = 0;
+	mode = 0;
+
+	if (dev->tdm_slots) {
+		slots = dev->tdm_slots;
+		slot_width = dev->slot_width;
+		frame_length = dev->frame_length;
+		rx_mask = dev->rx_mask;
+		tx_mask = dev->tx_mask;
+		bclk_rate = dev->frame_length * params_rate(params);
+	} else {
+		slots = 2;
+		slot_width = params_width(params);
+		rx_mask = 0x03;
+		tx_mask = 0x03;
+
+		frame_length = snd_soc_params_to_frame_size(params);
+		if (frame_length < 0)
+			return frame_length;
+
+		bclk_rate = snd_soc_params_to_bclk(params);
+		if (bclk_rate < 0)
+			return bclk_rate;
+	}
+
+	/* Check if data fits into slots */
+	if (data_length > slot_width)
+		return -EINVAL;
+
+	/* Check if CPU is bit clock master */
+	switch (dev->fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+	case SND_SOC_DAIFMT_CBS_CFS:
+	case SND_SOC_DAIFMT_CBS_CFM:
+		bit_clock_master = true;
 		break;
-	case SNDRV_PCM_FORMAT_S32_LE:
-		data_length = 32;
+	case SND_SOC_DAIFMT_CBM_CFS:
+	case SND_SOC_DAIFMT_CBM_CFM:
+		bit_clock_master = false;
 		break;
 	default:
 		return -EINVAL;
 	}
 
-	/* If bclk_ratio already set, use that one. */
-	if (dev->bclk_ratio)
-		bclk_ratio = dev->bclk_ratio;
-	else
-		/* otherwise calculate a fitting block ratio */
-		bclk_ratio = 2 * data_length;
-
-	/* Clock should only be set up here if CPU is clock master */
+	/* Check if CPU is frame sync master */
 	switch (dev->fmt & SND_SOC_DAIFMT_MASTER_MASK) {
 	case SND_SOC_DAIFMT_CBS_CFS:
+	case SND_SOC_DAIFMT_CBM_CFS:
+		frame_sync_master = true;
+		break;
 	case SND_SOC_DAIFMT_CBS_CFM:
-		clk_set_rate(dev->clk, sampling_rate * bclk_ratio);
+	case SND_SOC_DAIFMT_CBM_CFM:
+		frame_sync_master = false;
 		break;
 	default:
-		break;
+		return -EINVAL;
+	}
+
+	/* Clock should only be set up here if CPU is clock master */
+	if (bit_clock_master) {
+		ret = clk_set_rate(dev->clk, bclk_rate);
+		if (ret)
+			return ret;
 	}
 
 	/* Setup the frame format */
@@ -294,43 +433,94 @@ static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
 
 	format |= BCM2835_I2S_CHWID((data_length-8)&0xf);
 
+	/* CH2 format is the same as for CH1 */
+	format = BCM2835_I2S_CH1(format) | BCM2835_I2S_CH2(format);
+
 	switch (dev->fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
 	case SND_SOC_DAIFMT_I2S:
-		data_delay = 1;
-		break;
-	default:
+		/* I2S mode needs an even number of slots */
+		if (slots & 1)
+			return -EINVAL;
+
 		/*
-		 * TODO
-		 * Others are possible but are not implemented at the moment.
+		 * Use I2S-style logical slot numbering: even slots
+		 * are in first half of frame, odd slots in second half.
 		 */
-		dev_err(dev->dev, "%s:bad format\n", __func__);
-		return -EINVAL;
-	}
+		odd_slot_offset = slots >> 1;
 
-	ch1pos = data_delay;
-	ch2pos = bclk_ratio / 2 + data_delay;
+		/* MSB starts one cycle after frame start */
+		data_delay = 1;
 
-	switch (params_channels(params)) {
-	case 2:
-		format = BCM2835_I2S_CH1(format) | BCM2835_I2S_CH2(format);
-		format |= BCM2835_I2S_CH1(BCM2835_I2S_CHPOS(ch1pos));
-		format |= BCM2835_I2S_CH2(BCM2835_I2S_CHPOS(ch2pos));
+		/* Setup frame sync signal for 50% duty cycle */
+		framesync_length = frame_length / 2;
+		frame_start_falling_edge = true;
+		break;
+	case SND_SOC_DAIFMT_LEFT_J:
+		if (slots & 1)
+			return -EINVAL;
+
+		odd_slot_offset = slots >> 1;
+		data_delay = 0;
+		framesync_length = frame_length / 2;
+		frame_start_falling_edge = false;
+		break;
+	case SND_SOC_DAIFMT_RIGHT_J:
+		if (slots & 1)
+			return -EINVAL;
+
+		/* Odd frame lengths aren't supported */
+		if (frame_length & 1)
+			return -EINVAL;
+
+		odd_slot_offset = slots >> 1;
+		data_delay = slot_width - data_length;
+		framesync_length = frame_length / 2;
+		frame_start_falling_edge = false;
+		break;
+	case SND_SOC_DAIFMT_DSP_A:
+		data_delay = 1;
+		framesync_length = 1;
+		frame_start_falling_edge = false;
+		break;
+	case SND_SOC_DAIFMT_DSP_B:
+		data_delay = 0;
+		framesync_length = 1;
+		frame_start_falling_edge = false;
 		break;
 	default:
 		return -EINVAL;
 	}
 
+	bcm2835_i2s_calc_channel_pos(&rx_ch1_pos, &rx_ch2_pos,
+		rx_mask, slot_width, data_delay, odd_slot_offset);
+	bcm2835_i2s_calc_channel_pos(&tx_ch1_pos, &tx_ch2_pos,
+		tx_mask, slot_width, data_delay, odd_slot_offset);
+
+	/*
+	 * Transmitting data immediately after frame start, eg
+	 * in left-justified or DSP mode A, only works stable
+	 * if bcm2835 is the frame clock master.
+	 */
+	if ((!rx_ch1_pos || !tx_ch1_pos) && !frame_sync_master)
+		dev_warn(dev->dev,
+			"Unstable slave config detected, L/R may be swapped");
+
 	/*
 	 * Set format for both streams.
 	 * We cannot set another frame length
 	 * (and therefore word length) anyway,
 	 * so the format will be the same.
 	 */
-	regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, format);
-	regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, format);
+	regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, 
+		  format
+		| BCM2835_I2S_CH1_POS(rx_ch1_pos)
+		| BCM2835_I2S_CH2_POS(rx_ch2_pos));
+	regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, 
+		  format
+		| BCM2835_I2S_CH1_POS(tx_ch1_pos)
+		| BCM2835_I2S_CH2_POS(tx_ch2_pos));
 
 	/* Setup the I2S mode */
-	mode = 0;
 
 	if (data_length <= 16) {
 		/*
@@ -342,65 +532,41 @@ static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
 		mode |= BCM2835_I2S_FTXP | BCM2835_I2S_FRXP;
 	}
 
-	mode |= BCM2835_I2S_FLEN(bclk_ratio - 1);
-	mode |= BCM2835_I2S_FSLEN(bclk_ratio / 2);
+	mode |= BCM2835_I2S_FLEN(frame_length - 1);
+	mode |= BCM2835_I2S_FSLEN(framesync_length);
 
-	/* Master or slave? */
-	switch (dev->fmt & SND_SOC_DAIFMT_MASTER_MASK) {
-	case SND_SOC_DAIFMT_CBS_CFS:
-		/* CPU is master */
-		break;
-	case SND_SOC_DAIFMT_CBM_CFS:
-		/*
-		 * CODEC is bit clock master
-		 * CPU is frame master
-		 */
+	/* CLKM selects bcm2835 clock slave mode */
+	if (!bit_clock_master)
 		mode |= BCM2835_I2S_CLKM;
-		break;
-	case SND_SOC_DAIFMT_CBS_CFM:
-		/*
-		 * CODEC is frame master
-		 * CPU is bit clock master
-		 */
+
+	/* FSM selects bcm2835 frame sync slave mode */
+	if (!frame_sync_master)
 		mode |= BCM2835_I2S_FSM;
+
+	/* CLKI selects normal clocking mode, sampling on rising edge */
+        switch (dev->fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+	case SND_SOC_DAIFMT_NB_IF:
+		mode |= BCM2835_I2S_CLKI;
 		break;
-	case SND_SOC_DAIFMT_CBM_CFM:
-		/* CODEC is master */
-		mode |= BCM2835_I2S_CLKM;
-		mode |= BCM2835_I2S_FSM;
+	case SND_SOC_DAIFMT_IB_NF:
+	case SND_SOC_DAIFMT_IB_IF:
 		break;
 	default:
-		dev_err(dev->dev, "%s:bad master\n", __func__);
 		return -EINVAL;
 	}
 
-	/*
-	 * Invert clocks?
-	 *
-	 * The BCM approach seems to be inverted to the classical I2S approach.
-	 */
+	/* FSI selects frame start on falling edge */
 	switch (dev->fmt & SND_SOC_DAIFMT_INV_MASK) {
 	case SND_SOC_DAIFMT_NB_NF:
-		/* None. Therefore, both for BCM */
-		mode |= BCM2835_I2S_CLKI;
-		mode |= BCM2835_I2S_FSI;
-		break;
-	case SND_SOC_DAIFMT_IB_IF:
-		/* Both. Therefore, none for BCM */
+	case SND_SOC_DAIFMT_IB_NF:
+		if (frame_start_falling_edge)
+			mode |= BCM2835_I2S_FSI;
 		break;
 	case SND_SOC_DAIFMT_NB_IF:
-		/*
-		 * Invert only frame sync. Therefore,
-		 * invert only bit clock for BCM
-		 */
-		mode |= BCM2835_I2S_CLKI;
-		break;
-	case SND_SOC_DAIFMT_IB_NF:
-		/*
-		 * Invert only bit clock. Therefore,
-		 * invert only frame sync for BCM
-		 */
-		mode |= BCM2835_I2S_FSI;
+	case SND_SOC_DAIFMT_IB_IF:
+		if (!frame_start_falling_edge)
+			mode |= BCM2835_I2S_FSI;
 		break;
 	default:
 		return -EINVAL;
@@ -423,7 +589,27 @@ static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
 	/* Clear FIFOs */
 	bcm2835_i2s_clear_fifos(dev, true, true);
 
-	return 0;
+	dev_dbg(dev->dev,
+		"slots: %d width: %d rx mask: 0x%02x tx_mask: 0x%02x\n",
+		slots, slot_width, rx_mask, tx_mask);
+
+	dev_dbg(dev->dev, "frame len: %d sync len: %d data len: %d\n",
+		frame_length, framesync_length, data_length);
+
+	dev_dbg(dev->dev, "rx pos: %d,%d tx pos: %d,%d\n",
+		rx_ch1_pos, rx_ch2_pos, tx_ch1_pos, tx_ch2_pos);
+
+	dev_dbg(dev->dev, "sampling rate: %d bclk rate: %d\n",
+		params_rate(params), bclk_rate);
+
+	dev_dbg(dev->dev, "CLKM: %d CLKI: %d FSM: %d FSI: %d frame start: %s edge\n",
+		!!(mode & BCM2835_I2S_CLKM),
+		!!(mode & BCM2835_I2S_CLKI),
+		!!(mode & BCM2835_I2S_FSM),
+		!!(mode & BCM2835_I2S_FSI),
+		(mode & BCM2835_I2S_FSI) ? "falling" : "rising");
+
+	return ret;
 }
 
 static int bcm2835_i2s_prepare(struct snd_pcm_substream *substream,
@@ -559,6 +745,7 @@ static const struct snd_soc_dai_ops bcm2835_i2s_dai_ops = {
 	.hw_params	= bcm2835_i2s_hw_params,
 	.set_fmt	= bcm2835_i2s_set_dai_fmt,
 	.set_bclk_ratio	= bcm2835_i2s_set_dai_bclk_ratio,
+	.set_tdm_slot	= bcm2835_i2s_set_dai_tdm_slot,
 };
 
 static int bcm2835_i2s_dai_probe(struct snd_soc_dai *dai)
@@ -578,7 +765,9 @@ static struct snd_soc_dai_driver bcm2835_i2s_dai = {
 	.playback = {
 		.channels_min = 2,
 		.channels_max = 2,
-		.rates =	SNDRV_PCM_RATE_8000_192000,
+		.rates =	SNDRV_PCM_RATE_CONTINUOUS,
+		.rate_min =	8000,
+		.rate_max =	384000,
 		.formats =	SNDRV_PCM_FMTBIT_S16_LE
 				| SNDRV_PCM_FMTBIT_S24_LE
 				| SNDRV_PCM_FMTBIT_S32_LE
@@ -586,13 +775,16 @@ static struct snd_soc_dai_driver bcm2835_i2s_dai = {
 	.capture = {
 		.channels_min = 2,
 		.channels_max = 2,
-		.rates =	SNDRV_PCM_RATE_8000_192000,
+		.rates =	SNDRV_PCM_RATE_CONTINUOUS,
+		.rate_min =	8000,
+		.rate_max =	384000,
 		.formats =	SNDRV_PCM_FMTBIT_S16_LE
 				| SNDRV_PCM_FMTBIT_S24_LE
 				| SNDRV_PCM_FMTBIT_S32_LE
 		},
 	.ops = &bcm2835_i2s_dai_ops,
-	.symmetric_rates = 1
+	.symmetric_rates = 1,
+	.symmetric_samplebits = 1,
 };
 
 static bool bcm2835_i2s_volatile_reg(struct device *dev, unsigned int reg)
@@ -699,9 +891,6 @@ static int bcm2835_i2s_probe(struct platform_device *pdev)
 	dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].flags =
 		SND_DMAENGINE_PCM_DAI_FLAG_PACK;
 
-	/* BCLK ratio - use default */
-	dev->bclk_ratio = 0;
-
 	/* Store the pdev */
 	dev->dev = &pdev->dev;
 	dev_set_drvdata(&pdev->dev, dev);

sound/soc/codecs/cs43130.c

@@ -909,6 +909,7 @@ static int cs43130_hw_params(struct snd_pcm_substream *substream,
 		regmap_update_bits(cs43130->regmap, CS43130_DSD_PATH_CTL_2,
 				   CS43130_DSD_SRC_MASK, CS43130_DSD_SRC_XSP <<
 				   CS43130_DSD_SRC_SHIFT);
+		break;
 	}
 
 	if (!sclk && cs43130->dais[dai->id].dai_mode == SND_SOC_DAIFMT_CBM_CFM)
@@ -1039,6 +1040,7 @@ static int cs43130_pcm_ch_put(struct snd_kcontrol *kcontrol,
 		else
 			regmap_multi_reg_write(cs43130->regmap, pcm_ch_dis_seq,
 					       ARRAY_SIZE(pcm_ch_dis_seq));
+		break;
 	}
 
 	return snd_soc_put_enum_double(kcontrol, ucontrol);
@@ -1152,6 +1154,7 @@ static int cs43130_dsd_event(struct snd_soc_dapm_widget *w,
 		case CS4399_CHIP_ID:
 			regmap_multi_reg_write(cs43130->regmap, dsd_seq,
 					       ARRAY_SIZE(dsd_seq));
+			break;
 		}
 		break;
 	case SND_SOC_DAPM_POST_PMU:
@@ -1162,6 +1165,7 @@ static int cs43130_dsd_event(struct snd_soc_dapm_widget *w,
 		case CS4399_CHIP_ID:
 			regmap_multi_reg_write(cs43130->regmap, unmute_seq,
 					       ARRAY_SIZE(unmute_seq));
+			break;
 		}
 		break;
 	case SND_SOC_DAPM_PRE_PMD:
@@ -1184,6 +1188,7 @@ static int cs43130_dsd_event(struct snd_soc_dapm_widget *w,
 			regmap_update_bits(cs43130->regmap,
 					   CS43130_DSD_PATH_CTL_1,
 					   CS43130_MUTE_MASK, CS43130_MUTE_EN);
+			break;
 		}
 		break;
 	default:
@@ -1206,6 +1211,7 @@ static int cs43130_pcm_event(struct snd_soc_dapm_widget *w,
 		case CS4399_CHIP_ID:
 			regmap_multi_reg_write(cs43130->regmap, pcm_seq,
 					       ARRAY_SIZE(pcm_seq));
+			break;
 		}
 		break;
 	case SND_SOC_DAPM_POST_PMU:
@@ -1216,6 +1222,7 @@ static int cs43130_pcm_event(struct snd_soc_dapm_widget *w,
 		case CS4399_CHIP_ID:
 			regmap_multi_reg_write(cs43130->regmap, unmute_seq,
 					       ARRAY_SIZE(unmute_seq));
+			break;
 		}
 		break;
 	case SND_SOC_DAPM_PRE_PMD:
@@ -1238,6 +1245,7 @@ static int cs43130_pcm_event(struct snd_soc_dapm_widget *w,
 			regmap_update_bits(cs43130->regmap,
 					   CS43130_PCM_PATH_CTL_1,
 					   CS43130_MUTE_MASK, CS43130_MUTE_EN);
+			break;
 		}
 		break;
 	default:
@@ -1277,6 +1285,7 @@ static int cs43130_dac_event(struct snd_soc_dapm_widget *w,
 		case CS43198_CHIP_ID:
 			regmap_multi_reg_write(cs43130->regmap, pop_free_seq2,
 					       ARRAY_SIZE(pop_free_seq2));
+			break;
 		}
 		break;
 	case SND_SOC_DAPM_POST_PMU:
@@ -1301,6 +1310,7 @@ static int cs43130_dac_event(struct snd_soc_dapm_widget *w,
 		case CS43198_CHIP_ID:
 			usleep_range(12000, 12010);
 			regmap_write(cs43130->regmap, CS43130_DXD13, 0);
+			break;
 		}
 
 		regmap_write(cs43130->regmap, CS43130_DXD1, 0);
@@ -1311,6 +1321,7 @@ static int cs43130_dac_event(struct snd_soc_dapm_widget *w,
 		case CS4399_CHIP_ID:
 			regmap_multi_reg_write(cs43130->regmap, dac_postpmd_seq,
 					       ARRAY_SIZE(dac_postpmd_seq));
+			break;
 		}
 		break;
 	default:
@@ -2133,6 +2144,7 @@ static void cs43130_imp_meas(struct work_struct *wk)
 		cs43130_hpload_proc(cs43130, hp_dis_cal_seq2,
 				    ARRAY_SIZE(hp_dis_cal_seq2),
 				    CS43130_HPLOAD_OFF_INT, ac_idx);
+		break;
 	}
 
 	regmap_multi_reg_write(cs43130->regmap, hp_cln_seq,
@@ -2543,6 +2555,7 @@ static int cs43130_i2c_probe(struct i2c_client *client,
 			digital_hp_routes;
 		soc_codec_dev_cs43130.component_driver.num_dapm_routes =
 			ARRAY_SIZE(digital_hp_routes);
+		break;
 	}
 
 	ret = snd_soc_register_codec(&client->dev, &soc_codec_dev_cs43130,
@@ -2586,8 +2599,7 @@ static int cs43130_i2c_remove(struct i2c_client *client)
 		device_remove_file(&client->dev, &dev_attr_hpload_ac_r);
 	}
 
-	if (cs43130->reset_gpio)
-		gpiod_set_value_cansleep(cs43130->reset_gpio, 0);
+	gpiod_set_value_cansleep(cs43130->reset_gpio, 0);
 
 	pm_runtime_disable(&client->dev);
 	regulator_bulk_disable(CS43130_NUM_SUPPLIES, cs43130->supplies);