[ARM PATCH] 1503/1: Adds basic support for the iq80321 board

Patch from Eli Carter

# Tue Apr 15 16:07:34 CDT 2003 ejc@rnd-linux-c84
# add-iq80321
#
# Adds basic support for the iq80321 board.
#
# Diff'ed against 2.5.65-rmk1+1472-4+1502
# Applies to 2.5.67-rmk1+1502 with offsets
#
#  arch/arm/boot/Makefile                    |    1
#  arch/arm/boot/compressed/head-xscale.S    |    6
#  arch/arm/def-configs/iq80321              |  676 ++++++++++++++++++++++++++++++
#  arch/arm/kernel/debug.S                   |   10
#  arch/arm/kernel/entry-armv.S              |   22
#  arch/arm/mach-iop3xx/Kconfig              |   12
#  arch/arm/mach-iop3xx/Makefile             |   16
#  arch/arm/mach-iop3xx/arch.c               |   26 +
#  arch/arm/mach-iop3xx/iop321-irq.c         |   95 ++++
#  arch/arm/mach-iop3xx/iop321-pci.c         |  257 +++++++++++
#  arch/arm/mach-iop3xx/iop321-time.c        |   92 ++++
#  arch/arm/mach-iop3xx/iq80321-pci.c        |   98 ++++
#  arch/arm/mach-iop3xx/mm-321.c             |   64 ++
#  arch/arm/mm/proc-xscale.S                 |   19
#  include/asm-arm/arch-iop3xx/hardware.h    |   17
#  include/asm-arm/arch-iop3xx/iop321-irqs.h |   83 +++
#  include/asm-arm/arch-iop3xx/iop321.h      |  143 ++++++
#  include/asm-arm/arch-iop3xx/iq80321.h     |   17
#  include/asm-arm/arch-iop3xx/irqs.h        |   67 --
#  include/asm-arm/arch-iop3xx/memory.h      |   11
#  include/asm-arm/arch-iop3xx/serial.h      |   11
#  include/asm-arm/arch-iop3xx/timex.h       |    6
#  include/asm-arm/arch-iop3xx/uncompress.h  |    7
#  include/asm-arm/mach/pci.h                |    4
#  24 files changed, 1691 insertions(+), 69 deletions(-)

arch/arm/boot/Makefile

@@ -45,6 +45,7 @@ endif
   zreladdr-$(CONFIG_ARCH_PXA)		:= 0xa0008000
   zreladdr-$(CONFIG_ARCH_ANAKIN)	:= 0x20008000
   zreladdr-$(CONFIG_ARCH_IQ80310)	:= 0xa0008000
+  zreladdr-$(CONFIG_ARCH_IQ80321)	:= 0xa0008000
   zreladdr-$(CONFIG_ARCH_ADIFCC)	:= 0xc0008000
 
 ZRELADDR    := $(zreladdr-y)

arch/arm/boot/compressed/head-xscale.S

@@ -34,6 +34,12 @@ __XScale_start:
 		bic	r0, r0, #0x1000		@ clear Icache
 		mcr	p15, 0, r0, c1, c0, 0
 
+#ifdef	CONFIG_ARCH_IQ80321
+		orr	pc, pc, #0xa0000000
+		nop
+		mov	r7, #MACH_TYPE_IQ80321
+#endif
+
 #ifdef CONFIG_ARCH_LUBBOCK
 		mov	r7, #MACH_TYPE_LUBBOCK
 #endif

arch/arm/def-configs/iq80321

+#
+# Automatically generated make config: don't edit
+#
+CONFIG_ARM=y
+CONFIG_MMU=y
+CONFIG_SWAP=y
+CONFIG_UID16=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+
+#
+# Code maturity level options
+#
+# CONFIG_EXPERIMENTAL is not set
+
+#
+# General setup
+#
+CONFIG_SYSVIPC=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+CONFIG_LOG_BUF_SHIFT=14
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+# CONFIG_MODULE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+CONFIG_KMOD=y
+
+#
+# System Type
+#
+# CONFIG_ARCH_ADIFCC is not set
+# CONFIG_ARCH_ANAKIN is not set
+# CONFIG_ARCH_ARCA5K is not set
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_CAMELOT is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+CONFIG_ARCH_IOP3XX=y
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_SHARK is not set
+
+#
+# Archimedes/A5000 Implementations
+#
+
+#
+# Archimedes/A5000 Implementations (select only ONE)
+#
+
+#
+# CLPS711X/EP721X Implementations
+#
+
+#
+# Epxa10db
+#
+
+#
+# Footbridge Implementations
+#
+
+#
+# IOP3xx Implementation Options
+#
+# CONFIG_ARCH_IQ80310 is not set
+CONFIG_ARCH_IQ80321=y
+# CONFIG_ARCH_IOP310 is not set
+CONFIG_ARCH_IOP321=y
+
+#
+# IOP3xx Chipset Features
+#
+
+#
+# Intel PXA250/210 Implementations
+#
+
+#
+# SA11x0 Implementations
+#
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+
+#
+# Processor Features
+#
+CONFIG_XSCALE_PMU=y
+
+#
+# General setup
+#
+CONFIG_PCI=y
+# CONFIG_ZBOOT_ROM is not set
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+# CONFIG_PCI_LEGACY_PROC is not set
+CONFIG_PCI_NAMES=y
+# CONFIG_HOTPLUG is not set
+
+#
+# At least one math emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+CONFIG_KCORE_ELF=y
+# CONFIG_KCORE_AOUT is not set
+CONFIG_BINFMT_AOUT=y
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_PM is not set
+# CONFIG_ARTHUR is not set
+CONFIG_CMDLINE="ip=boot root=nfs console=ttyS0,115200"
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_REDBOOT_PARTS=y
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_NORA is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+CONFIG_MTD_IQ80321=y
+# CONFIG_MTD_EDB7312 is not set
+# CONFIG_MTD_PCI is not set
+# CONFIG_MTD_UCLINUX is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC1000 is not set
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNP is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+# CONFIG_BLK_DEV_INITRD is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Networking support
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_PACKET is not set
+# CONFIG_NETLINK_DEV is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+# CONFIG_FILTER is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_INET_ECN is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_XFRM_USER is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_CONNTRACK is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
+# CONFIG_IP_NF_COMPAT_IPFWADM is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_LLC is not set
+# CONFIG_DECNET is not set
+# CONFIG_BRIDGE is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+CONFIG_NETDEVICES=y
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_DGRS is not set
+CONFIG_EEPRO100=y
+# CONFIG_E100 is not set
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139TOO is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_R8169 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_FDDI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Token Ring devices (depends on LLC=y)
+#
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+
+#
+# IrDA (infrared) support
+#
+# CONFIG_IRDA is not set
+
+#
+# Amateur Radio support
+#
+# CONFIG_HAMRADIO is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=y
+
+#
+# IDE, ATA and ATAPI Block devices
+#
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_HD is not set
+CONFIG_BLK_DEV_IDEDISK=y
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_IDEDISK_STROKE is not set
+CONFIG_BLK_DEV_IDECD=y
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_BLK_DEV_IDEPCI=y
+# CONFIG_BLK_DEV_GENERIC is not set
+# CONFIG_IDEPCI_SHARE_IRQ is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
+CONFIG_IDEDMA_PCI_AUTO=y
+# CONFIG_IDEDMA_ONLYDISK is not set
+CONFIG_BLK_DEV_IDEDMA=y
+CONFIG_BLK_DEV_ADMA=y
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+CONFIG_BLK_DEV_CMD64X=y
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_IDEDMA_AUTO=y
+# CONFIG_IDEDMA_IVB is not set
+CONFIG_BLK_DEV_IDE_MODES=y
+
+#
+# SCSI support
+#
+# CONFIG_SCSI is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN_BOOL is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Userland interfaces
+#
+
+#
+# Input I/O drivers
+#
+# CONFIG_GAMEPORT is not set
+CONFIG_SOUND_GAMEPORT=y
+# CONFIG_SERIO is not set
+
+#
+# Input Device Drivers
+#
+
+#
+# Character devices
+#
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_DZ is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_UNIX98_PTY_COUNT=256
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# I2C Hardware Sensors Mainboard support
+#
+
+#
+# I2C Hardware Sensors Chip support
+#
+
+#
+# L3 serial bus support
+#
+# CONFIG_L3 is not set
+
+#
+# Mice
+#
+# CONFIG_BUSMOUSE is not set
+# CONFIG_QIC02_TAPE is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+# CONFIG_RTC is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_FTAPE is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# Multimedia devices
+#
+CONFIG_VIDEO_DEV=y
+
+#
+# Video For Linux
+#
+# CONFIG_VIDEO_PROC_FS is not set
+
+#
+# Video Adapters
+#
+# CONFIG_VIDEO_PMS is not set
+# CONFIG_VIDEO_CPIA is not set
+
+#
+# Radio Adapters
+#
+# CONFIG_RADIO_GEMTEK_PCI is not set
+# CONFIG_RADIO_MAXIRADIO is not set
+# CONFIG_RADIO_MAESTRO is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# File systems
+#
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_JBD is not set
+# CONFIG_FAT_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+# CONFIG_CRAMFS is not set
+CONFIG_TMPFS=y
+CONFIG_RAMFS=y
+# CONFIG_ISO9660_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_NTFS_FS is not set
+# CONFIG_HPFS_FS is not set
+CONFIG_PROC_FS=y
+CONFIG_DEVPTS_FS=y
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UDF_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_XFS_FS is not set
+
+#
+# Network File Systems
+#
+# CONFIG_CODA_FS is not set
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_SUNRPC=y
+CONFIG_LOCKD=y
+# CONFIG_EXPORTFS is not set
+# CONFIG_CIFS is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_NCP_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_MDA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+# CONFIG_MCP is not set
+
+#
+# Console Switches
+#
+# CONFIG_SWITCHES is not set
+
+#
+# USB support
+#
+# CONFIG_USB is not set
+
+#
+# Bluetooth support
+#
+# CONFIG_BT is not set
+
+#
+# Kernel hacking
+#
+CONFIG_FRAME_POINTER=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_INFO is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_WAITQ is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_ERRORS=y
+# CONFIG_KALLSYMS is not set
+CONFIG_DEBUG_LL=y
+
+#
+# Security options
+#
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC32 is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y

arch/arm/kernel/debug.S

@@ -414,7 +414,13 @@
 
 		.macro	addruart,rx
 		mov	\rx, #0xfe000000	@ physical
-		orr	\rx, \rx, #0x00810000
+#ifdef CONFIG_ARCH_IQ80310
+		orr	\rx, \rx, #0x00810000	@ location of the UART
+#elif defined(CONFIG_ARCH_IQ80321)
+		orr	\rx, \rx, #0x00800000	@ location of the UART
+#else
+#error Unknown IOP3XX implementation
+#endif
 		.endm
 
 		.macro	senduart,rd,rx
@@ -429,9 +435,11 @@
 		.endm
 
 		.macro	waituart,rd,rx
+#ifndef	CONFIG_ARCH_IQ80321
 1001:		ldrb	\rd, [\rx, #0x6]
 		tst	\rd, #0x10
 		beq	1001b
+#endif
 		.endm
 
 #elif defined(CONFIG_ARCH_ADI_EVB)

arch/arm/kernel/entry-armv.S

@@ -584,6 +584,28 @@ ENTRY(anakin_active_irqs)
   		.macro	irq_prio_table
  		.endm
 
+#elif defined(CONFIG_ARCH_IOP321)
+		.macro  disable_fiq
+		.endm
+
+		/*
+		 * Note: only deal with normal interrupts, not FIQ
+		 */
+		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+		mov     \irqnr, #0
+		mrc     p6, 0, \irqstat, c8, c0, 0      @ Read IINTSRC
+		cmp     \irqstat, #0
+		beq     1001f
+		clz     \irqnr, \irqstat
+		mov     \base, #31
+		subs    \irqnr,\base,\irqnr
+		add     \irqnr,\irqnr,#IRQ_IOP321_DMA0_EOT
+1001:
+		.endm
+
+		.macro  irq_prio_table
+		.endm
+
 #elif defined(CONFIG_ARCH_PXA)
 
 		.macro	disable_fiq

arch/arm/mach-iop3xx/Kconfig

@@ -12,6 +12,12 @@ config ARCH_IQ80310
 	  Say Y here if you want to run your kernel on the Intel IQ80310
 	  evaluation kit for the IOP310 chipset.
 
+config ARCH_IQ80321
+	bool "IQ80321"
+	depends on ARCH_IOP3XX
+	help
+	  Say Y here if you want to run your kernel on the Intel IQ80321
+	  evaluation kit for the IOP321 chipset.
 endchoice
 
 # Which IOP variant are we running?
@@ -21,6 +27,12 @@ config ARCH_IOP310
 	help
 	  The IQ80310 uses the IOP310 variant.
 
+config ARCH_IOP321
+	bool
+	default ARCH_IQ80321
+	help
+	  The IQ80321 uses the IOP321 variant.
+
 comment "IOP3xx Chipset Features"
 
 config IOP3XX_AAU

arch/arm/mach-iop3xx/Makefile

@@ -4,16 +4,24 @@
 
 # Object file lists.
 
-obj-y			:= arch.o mm.o xs80200-irq.o iop310-irq.o \
-			   iop310-pci.o
+obj-y			:= arch.o
+
 obj-m			:=
 obj-n			:=
 obj-			:=
 
+obj-$(CONFIG_ARCH_IOP310)  += xs80200-irq.o iop310-irq.o iop310-pci.o mm.o
+
 obj-$(CONFIG_ARCH_IQ80310) += iq80310-pci.o iq80310-irq.o
 
-ifneq ($(CONFIG_XSCALE_PMU_TIMER),y)
-obj-y			+= iq80310-time.o
+obj-$(CONFIG_ARCH_IOP321)  += iop321-irq.o iop321-pci.o mm-321.o iop321-time.o
+
+obj-$(CONFIG_ARCH_IQ80321) += iq80321-pci.o
+
+ifeq ($(CONFIG_ARCH_IQ80310),y)
+   ifneq ($(CONFIG_XSCALE_PMU_TIMER),y)
+      obj-y			+= iq80310-time.o
+   endif
 endif
 
 obj-$(CONFIG_IOP3XX_AAU) += aau.o

arch/arm/mach-iop3xx/arch.c

@@ -24,7 +24,14 @@
 #ifdef CONFIG_ARCH_IQ80310
 extern void iq80310_map_io(void);
 extern void iq80310_init_irq(void);
+#endif
+
+#ifdef CONFIG_ARCH_IQ80321
+extern void iq80321_map_io(void);
+extern void iop321_init_irq(void);
+#endif
 
+#ifdef CONFIG_ARCH_IQ80310
 static void __init
 fixup_iq80310(struct machine_desc *desc, struct tag *tags,
 	      char **cmdline, struct meminfo *mi)
@@ -34,7 +41,17 @@ fixup_iq80310(struct machine_desc *desc, struct tag *tags,
 	if (system_rev)
 		system_rev = 0xF;
 }
+#endif
+
+#ifdef CONFIG_ARCH_IQ80321
+static void __init
+fixup_iop321(struct machine_desc *desc, struct param_struct *params,
+	      char **cmdline, struct meminfo *mi)
+{
+}
+#endif
 
+#ifdef CONFIG_ARCH_IQ80310
 MACHINE_START(IQ80310, "Cyclone IQ80310")
 	MAINTAINER("MontaVista Software Inc.")
 	BOOT_MEM(0xa0000000, 0xfe000000, 0xfe000000)
@@ -43,6 +60,15 @@ MACHINE_START(IQ80310, "Cyclone IQ80310")
 	INITIRQ(iq80310_init_irq)
 MACHINE_END
 
+#elif defined(CONFIG_ARCH_IQ80321)
+MACHINE_START(IQ80321, "Intel IQ80321")
+	MAINTAINER("MontaVista Software, Inc.")
+	BOOT_MEM(PHYS_OFFSET, IQ80321_UART1, 0xfe800000)
+	FIXUP(fixup_iop321)
+	MAPIO(iq80321_map_io)
+	INITIRQ(iop321_init_irq)
+MACHINE_END
+
 #else
 #error No machine descriptor defined for this IOP310 implementation
 #endif

arch/arm/mach-iop3xx/iop321-irq.c

+/*
+ * linux/arch/arm/mach-iop3xx/iop321-irq.c
+ *
+ * Generic IOP321 IRQ handling functionality
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Added IOP3XX chipset and IQ80321 board masking code.
+ *
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+
+#include <asm/mach/irq.h>
+#include <asm/irq.h>
+#include <asm/hardware.h>
+
+#include <asm/mach-types.h>
+
+static u32 iop321_mask /* = 0 */;
+
+static inline void intctl_write(u32 val)
+{
+	asm volatile("mcr p6,0,%0,c0,c0,0"::"r" (val));
+}
+
+static inline void intstr_write(u32 val)
+{
+	asm volatile("mcr p6,0,%0,c4,c0,0"::"r" (val));
+}
+
+static void
+iop321_irq_mask (unsigned int irq)
+{
+
+	iop321_mask &= ~(1 << (irq - IOP321_IRQ_OFS));
+
+	intctl_write(iop321_mask);
+}
+
+static void
+iop321_irq_unmask (unsigned int irq)
+{
+	iop321_mask |= (1 << (irq - IOP321_IRQ_OFS));
+
+	intctl_write(iop321_mask);
+}
+
+struct irqchip ext_chip = {
+	.ack    = iop321_irq_mask,
+	.mask   = iop321_irq_mask,
+	.unmask = iop321_irq_unmask,
+};
+
+void __init iop321_init_irq(void)
+{
+	unsigned int i, tmp;
+
+	/* Enable access to coprocessor 6 for dealing with IRQs.
+	 * From RMK:
+	 * Basically, the Intel documentation here is poor.  It appears that
+	 * you need to set the bit to be able to access the coprocessor from
+	 * SVC mode.  Whether that allows access from user space or not is
+	 * unclear.
+	 */
+	asm volatile (
+		"mrc p15, 0, %0, c15, c1, 0\n\t"
+		"orr %0, %0, %1\n\t"
+		"mcr p15, 0, %0, c15, c1, 0\n\t"
+		/* The action is delayed, so we have to do this: */
+		"mrc p15, 0, %0, c15, c1, 0\n\t"
+		"mov %0, %0\n\t"
+		"sub pc, pc, #4"
+		: "=r" (tmp) : "i" (1 << 6) );
+
+	intctl_write(0);		// disable all interrupts
+	intstr_write(0);		// treat all as IRQ
+	if(machine_is_iq80321()) 	// all interrupts are inputs to chip
+		*IOP321_PCIIRSR = 0x0f;
+
+	for(i = IOP321_IRQ_OFS; i < NR_IOP321_IRQS; i++)
+	{
+		set_irq_chip(i, &ext_chip);
+		set_irq_handler(i, do_level_IRQ);
+		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+
+	}
+}
+

arch/arm/mach-iop3xx/iop321-pci.c

+/*
+ * arch/arm/mach-iop3xx/iop321-pci.c
+ *
+ * PCI support for the Intel IOP321 chipset
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/system.h>
+#include <asm/hardware.h>
+#include <asm/mach/pci.h>
+
+#include <asm/arch/iop321.h>
+
+// #define DEBUG
+
+#ifdef DEBUG
+#define  DBG(x...) printk(x)
+#else
+#define  DBG(x...) do { } while (0)
+#endif
+
+/*
+ * This routine builds either a type0 or type1 configuration command.  If the
+ * bus is on the 80321 then a type0 made, else a type1 is created.
+ */
+static u32 iop321_cfg_address(struct pci_bus *bus, int devfn, int where)
+{
+	struct pci_sys_data *sys = bus->sysdata;
+	u32 addr;
+
+	if (sys->busnr == bus->number)
+		addr = 1 << (PCI_SLOT(devfn) + 16);
+	else
+		addr = bus->number << 16 | PCI_SLOT(devfn) << 11 | 1;
+
+	addr |=	PCI_FUNC(devfn) << 8 | (where & ~3);
+
+	return addr;
+}
+
+/*
+ * This routine checks the status of the last configuration cycle.  If an error
+ * was detected it returns a 1, else it returns a 0.  The errors being checked
+ * are parity, master abort, target abort (master and target).  These types of
+ * errors occure during a config cycle where there is no device, like during
+ * the discovery stage.
+ */
+static int iop321_pci_status(void)
+{
+	unsigned int status;
+	int ret = 0;
+
+	/*
+	 * Check the status registers.
+	 */
+	status = *IOP321_ATUSR;
+	if (status & 0xf900)
+	{
+		DBG("\t\t\tPCI: P0 - status = 0x%08x\n", status);
+		*IOP321_ATUSR = status & 0xf900;
+		ret = 1;
+	}
+	status = *IOP321_ATUISR;
+	if (status & 0x679f)
+	{
+		DBG("\t\t\tPCI: P1 - status = 0x%08x\n", status);
+		*IOP321_ATUISR = status & 0x679f;
+		ret = 1;
+	}
+	return ret;
+}
+
+/*
+ * Simply write the address register and read the configuration
+ * data.  Note that the 4 nop's ensure that we are able to handle
+ * a delayed abort (in theory.)
+ */
+static inline u32 iop321_read(unsigned long addr)
+{
+	u32 val;
+
+	__asm__ __volatile__(
+		"str	%1, [%2]\n\t"
+		"ldr	%0, [%3]\n\t"
+		"nop\n\t"
+		"nop\n\t"
+		"nop\n\t"
+		"nop\n\t"
+		: "=r" (val)
+		: "r" (addr), "r" (IOP321_OCCAR), "r" (IOP321_OCCDR));
+
+	return val;
+}
+
+/*
+ * The read routines must check the error status of the last configuration
+ * cycle.  If there was an error, the routine returns all hex f's.
+ */
+static int
+iop321_read_config(struct pci_bus *bus, unsigned int devfn, int where,
+		int size, u32 *value)
+{
+	unsigned long addr = iop321_cfg_address(bus, devfn, where);
+	u32 val = iop321_read(addr) >> ((where & 3) * 8);
+
+	if( iop321_pci_status() )
+		val = 0xffffffff;
+
+	*value = val;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int
+iop321_write_config(struct pci_bus *bus, unsigned int devfn, int where,
+		int size, u32 value)
+{
+	unsigned long addr = iop321_cfg_address(bus, devfn, where);
+	u32 val;
+
+	if (size != 4) {
+		val = iop321_read(addr);
+		if (!iop321_pci_status() == 0)
+			return PCIBIOS_SUCCESSFUL;
+
+		where = (where & 3) * 8;
+
+		if (size == 1)
+			val &= ~(0xff << where);
+		else
+			val &= ~(0xffff << where);
+
+		*IOP321_OCCDR = val | value << where;
+	} else {
+		asm volatile(
+			"str	%1, [%2]\n\t"
+			"str	%0, [%3]\n\t"
+			"nop\n\t"
+			"nop\n\t"
+			"nop\n\t"
+			"nop\n\t"
+			:
+			: "r" (value), "r" (addr),
+			  "r" (IOP321_OCCAR), "r" (IOP321_OCCDR));
+	}
+}
+
+static struct pci_ops iop321_ops = {
+	.read	= iop321_read_config,
+	.write	= iop321_write_config,
+};
+
+/*
+ * When a PCI device does not exist during config cycles, the 80200 gets a
+ * bus error instead of returning 0xffffffff. This handler simply returns.
+ */
+int
+iop321_pci_abort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
+{
+	DBG("PCI abort: address = 0x%08lx fsr = 0x%03x PC = 0x%08lx LR = 0x%08lx\n",
+		addr, fsr, regs->ARM_pc, regs->ARM_lr);
+
+	/*
+	 * If it was an imprecise abort, then we need to correct the
+	 * return address to be _after_ the instruction.
+	 */
+	if (fsr & (1 << 10))
+		regs->ARM_pc += 4;
+
+	return 0;
+}
+
+/*
+ * Scan an IOP321 PCI bus.  sys->bus defines which bus we scan.
+ */
+struct pci_bus *iop321_scan_bus(int nr, struct pci_sys_data *sys)
+{
+	return pci_scan_bus(sys->busnr, &iop321_ops, sys);
+}
+
+/*
+ * Setup the system data for controller 'nr'.   Return 0 if none found,
+ * 1 if found, or negative error.
+ */
+int iop321_setup(int nr, struct pci_sys_data *sys)
+{
+	struct resource *res;
+
+	if (nr >= 1)
+		return 0;
+
+	res = kmalloc(sizeof(struct resource) * 2, GFP_KERNEL);
+	if (!res)
+		panic("PCI: unable to alloc resources");
+
+	memset(res, 0, sizeof(struct resource) * 2);
+
+	switch (nr) {
+	case 0:
+		res[0].start = IOP321_PCI_LOWER_IO + 0x6e000000;
+		res[0].end   = IOP321_PCI_LOWER_IO + 0x6e00ffff;
+		res[0].name  = "PCI IO Primary";
+		res[0].flags = IORESOURCE_IO;
+
+		res[1].start = IOP321_PCI_LOWER_MEM;
+		res[1].end   = IOP321_PCI_LOWER_MEM + IOP321_PCI_WINDOW_SIZE;
+		res[1].name  = "PCI Memory Primary";
+		res[1].flags = IORESOURCE_MEM;
+		break;
+	}
+
+	request_resource(&ioport_resource, &res[0]);
+	request_resource(&iomem_resource, &res[1]);
+
+	sys->resource[0] = &res[0];
+	sys->resource[1] = &res[1];
+	sys->resource[2] = NULL;
+	sys->io_offset   = 0x6e000000;
+
+	return 1;
+}
+
+
+
+
+void iop321_init(void)
+{
+	DBG("PCI:  Intel 80321 PCI init code.\n");
+	DBG("\tATU: IOP321_ATUCMD=0x%04x\n", *IOP321_ATUCMD);
+	DBG("\tATU: IOP321_OMWTVR0=0x%04x, IOP321_OIOWTVR=0x%04x\n",
+			*IOP321_OMWTVR0,
+			*IOP321_OIOWTVR);
+	DBG("\tATU: IOP321_ATUCR=0x%08x\n", *IOP321_ATUCR);
+	DBG("\tATU: IOP321_IABAR0=0x%08x IOP321_IALR0=0x%08x IOP321_IATVR0=%08x\n", *IOP321_IABAR0, *IOP321_IALR0, *IOP321_IATVR0);
+	DBG("\tATU: IOP321_ERBAR=0x%08x IOP321_ERLR=0x%08x IOP321_ERTVR=%08x\n", *IOP321_ERBAR, *IOP321_ERLR, *IOP321_ERTVR);
+	DBG("\tATU: IOP321_IABAR2=0x%08x IOP321_IALR2=0x%08x IOP321_IATVR2=%08x\n", *IOP321_IABAR2, *IOP321_IALR2, *IOP321_IATVR2);
+	DBG("\tATU: IOP321_IABAR3=0x%08x IOP321_IALR3=0x%08x IOP321_IATVR3=%08x\n", *IOP321_IABAR3, *IOP321_IALR3, *IOP321_IATVR3);
+
+	hook_fault_code(16+6, iop321_pci_abort, SIGBUS, "imprecise external abort");
+
+}
+

arch/arm/mach-iop3xx/iop321-time.c

+/*
+ * arch/arm/mach-iop3xx/iop321-time.c
+ *
+ * Timer code for IOP321 based systems
+ *
+ * Author: Deepak Saxena <dsaxena@mvista.com>
+ *
+ * Copyright 2002 MontaVista Software Inc.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/init.h>
+#include <linux/timex.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+#include <asm/mach-types.h>
+#include <asm/mach/irq.h>
+
+static unsigned long iop321_gettimeoffset(void)
+{
+	unsigned long elapsed, usec;
+
+	/*
+	 * FIXME: Implement what is described in this comment.
+	 *
+	 * If an interrupt was pending before we read the timer,
+	 * we've already wrapped.  Factor this into the time.
+	 * If an interrupt was pending after we read the timer,
+	 * it may have wrapped between checking the interrupt
+	 * status and reading the timer.  Re-read the timer to
+	 * be sure its value is after the wrap.
+	 */
+
+	elapsed = *IOP321_TU_TCR0;
+
+	/*
+	 * Now convert them to usec.
+	 */
+	usec = (unsigned long)((LATCH - elapsed) * (tick_nsec / 1000)) / LATCH;
+
+	return usec;
+}
+
+static void iop321_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	u32 tisr;
+
+	asm volatile("mrc p6, 0, %0, c6, c1, 0" : "=r" (tisr));
+
+	tisr |= 1;
+
+	asm volatile("mcr p6, 0, %0, c6, c1, 0" : : "r" (tisr));
+
+	do_timer(regs);
+}
+
+extern unsigned long (*gettimeoffset)(void);
+
+static struct irqaction timer_irq = {
+	.name		= "timer",
+	.handler	= iop321_timer_interrupt,
+};
+
+extern int setup_arm_irq(int, struct irqaction*);
+
+void __init time_init(void)
+{
+	u32 timer_ctl;
+	u32 latch = LATCH;
+
+	gettimeoffset = iop321_gettimeoffset;
+	setup_irq(IRQ_IOP321_TIMER0, &timer_irq);
+
+	timer_ctl = IOP321_TMR_EN | IOP321_TMR_PRIVILEGED | IOP321_TMR_RELOAD |
+			IOP321_TMR_RATIO_1_1;
+
+	asm volatile("mcr p6, 0, %0, c4, c1, 0" : : "r" (LATCH));
+
+	asm volatile("mcr p6, 0, %0, c0, c1, 0"	: : "r" (timer_ctl));
+}
+
+

arch/arm/mach-iop3xx/iq80321-pci.c

+/*
+ * arch/arm/mach-iop3xx/iq80321-pci.c
+ *
+ * PCI support for the Intel IQ80321 reference board
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach/pci.h>
+#include <asm/mach-types.h>
+
+/*
+ * The following macro is used to lookup irqs in a standard table
+ * format for those systems that do not already have PCI
+ * interrupts properly routed.  We assume 1 <= pin <= 4
+ */
+#define PCI_IRQ_TABLE_LOOKUP(minid,maxid)	\
+({ int _ctl_ = -1;				\
+   unsigned int _idsel = idsel - minid;		\
+   if (_idsel <= maxid)				\
+      _ctl_ = pci_irq_table[_idsel][pin-1];	\
+   _ctl_; })
+
+#define INTA	IRQ_IQ80321_INTA
+#define INTB	IRQ_IQ80321_INTB
+#define INTC	IRQ_IQ80321_INTC
+#define INTD	IRQ_IQ80321_INTD
+
+#define INTE	IRQ_IQ80321_I82544
+
+typedef u8 irq_table[4];
+
+static irq_table pci_irq_table[] = {
+	/*
+	 * PCI IDSEL/INTPIN->INTLINE
+	 * A       B       C       D
+	 */
+	{INTE, INTE, INTE, INTE}, /* Gig-E */
+	{INTD, INTC, INTD, INTA}, /* Unused */
+	{INTC, INTD, INTA, INTB}, /* PCI-X Slot */
+};
+
+static inline int __init
+iq80321_map_irq(struct pci_dev *dev, u8 idsel, u8 pin)
+{
+	BUG_ON(pin < 1 || pin > 4);
+
+	return PCI_IRQ_TABLE_LOOKUP(2, 3);
+}
+
+static int iq80321_setup(int nr, struct pci_sys_data *sys)
+{
+	switch (nr) {
+	case 0:
+		sys->map_irq = iq80321_map_irq;
+		break;
+	default:
+		return 0;
+	}
+
+	return iop321_setup(nr, sys);
+}
+
+static void iq80321_preinit(void)
+{
+	iop321_init();
+}
+
+static struct hw_pci iq80321_pci __initdata = {
+	.swizzle	= pci_std_swizzle,
+	.nr_controllers = 1,
+	.setup		= iq80321_setup,
+	.scan		= iop321_scan_bus,
+	.preinit	= iq80321_preinit,
+};
+
+static int __init iq80321_pci_init(void)
+{
+	if (machine_is_iq80321())
+		pci_common_init(&iq80321_pci);
+	return 0;
+}
+
+subsys_initcall(iq80321_pci_init);
+
+
+
+

arch/arm/mach-iop3xx/mm-321.c

+/*
+ * linux/arch/arm/mach-iop3xx/mm.c
+ *
+ * Low level memory intialization for IOP321 based systems
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+
+#include <asm/mach/map.h>
+#include <asm/mach-types.h>
+
+
+/*
+ * Standard IO mapping for all IOP321 based systems
+ */
+static struct map_desc iop80321_std_desc[] __initdata = {
+ /* virtual     physical      length      type */
+
+ /* mem mapped registers */
+ { 0xfff00000,  0xffffe000,   0x00002000,  MT_DEVICE },
+
+ /* PCI IO space */
+ { 0xfe000000,  0x90000000,   0x00020000,  MT_DEVICE }
+};
+
+void __init iop321_map_io(void)
+{
+	iotable_init(iop80321_std_desc, ARRAY_SIZE(iop80321_std_desc));
+}
+
+/*
+ * IQ80321 specific IO mappings
+ *
+ * We use RedBoot's setup for the onboard devices.
+ */
+#ifdef CONFIG_ARCH_IQ80321
+static struct map_desc iq80321_io_desc[] __initdata = {
+ /* virtual     physical      length        type */
+
+ /* on-board devices */
+ { 0xfe800000,  0xfe800000,   0x00100000,   MT_DEVICE }
+};
+
+void __init iq80321_map_io(void)
+{
+	iop321_map_io();
+
+	iotable_init(iq80321_io_desc, ARRAY_SIZE(iq80321_io_desc));
+}
+#endif // CONFIG_ARCH_IQ80321

arch/arm/mm/proc-xscale.S

@@ -654,6 +654,9 @@ ENTRY(cpu_xscale_set_pte)
 cpu_80200_name:
 	.asciz	"XScale-80200"
 
+cpu_80321_name:
+	.asciz	"XScale-IOP80321"
+
 cpu_pxa250_name:
 	.asciz	"XScale-PXA250"
 
@@ -748,6 +751,22 @@ __80200_proc_info:
 	.long	xscale_mc_user_fns
 	.size	__80200_proc_info, . - __80200_proc_info
 
+	.type	__80321_proc_info,#object
+__80321_proc_info:
+	.long	0x69052420
+	.long	0xfffffff0
+	.long	0x00000c0e
+	b	__xscale_setup
+	.long	cpu_arch_name
+	.long	cpu_elf_name
+	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP
+	.long	cpu_80321_name
+	.long	xscale_processor_functions
+	.long	v4wbi_tlb_fns
+	.long	xscale_mc_user_fns
+	.long	xscale_cache_fns
+	.size	__80321_proc_info, . - __80321_proc_info
+
 	.type	__pxa250_proc_info,#object
 __pxa250_proc_info:
 	.long	0x69052100

include/asm-arm/arch-iop3xx/hardware.h

@@ -20,6 +20,7 @@
 
 #define pcibios_assign_all_busses() 1
 
+#ifdef CONFIG_ARCH_IOP310
 /*
  * these are the values for the secondary PCI bus on the 80312 chip.  I will
  * have to do some fixup in the bus/dev fixup code
@@ -34,5 +35,21 @@
 #if defined(CONFIG_ARCH_IQ80310)
 #include "iq80310.h"
 #endif
+#endif
+
+#ifdef CONFIG_ARCH_IOP321
+
+#define PCIBIOS_MIN_IO		0x90000000
+#define PCIBIOS_MIN_MEM		0x80000000
+
+#include "iop321.h"
+
+#ifdef CONFIG_ARCH_IQ80321
+#include "iq80321.h"
+#endif
+#endif
+
+
+
 
 #endif  /* _ASM_ARCH_HARDWARE_H */

include/asm-arm/arch-iop3xx/iop321-irqs.h

+/*
+ * linux/include/asm-arm/arch-iop3xx/irqs.h
+ *
+ * Author:	Rory Bolt <rorybolt@pacbell.net>
+ * Copyright:	(C) 2002 Rory Bolt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+
+/*
+ * IOP80321 chipset interrupts
+ */
+#define IOP321_IRQ_OFS		0
+#define IOP321_IRQ(x)		(IOP321_IRQ_OFS + (x))
+
+/*
+ * On IRQ or FIQ register
+ */
+#define IRQ_IOP321_DMA0_EOT	IOP321_IRQ(0)
+#define IRQ_IOP321_DMA0_EOC	IOP321_IRQ(1)
+#define IRQ_IOP321_DMA1_EOT	IOP321_IRQ(2)
+#define IRQ_IOP321_DMA1_EOC	IOP321_IRQ(3)
+#define IRQ_IOP321_RSVD_4	IOP321_IRQ(4)
+#define IRQ_IOP321_RSVD_5	IOP321_IRQ(5)
+#define IRQ_IOP321_AA_EOT	IOP321_IRQ(6)
+#define IRQ_IOP321_AA_EOC	IOP321_IRQ(7)
+#define IRQ_IOP321_CORE_PMON	IOP321_IRQ(8)
+#define IRQ_IOP321_TIMER0	IOP321_IRQ(9)
+#define IRQ_IOP321_TIMER1	IOP321_IRQ(10)
+#define IRQ_IOP321_I2C_0	IOP321_IRQ(11)
+#define IRQ_IOP321_I2C_1	IOP321_IRQ(12)
+#define IRQ_IOP321_MESSAGING	IOP321_IRQ(13)
+#define IRQ_IOP321_ATU_BIST	IOP321_IRQ(14)
+#define IRQ_IOP321_PERFMON	IOP321_IRQ(15)
+#define IRQ_IOP321_CORE_PMU	IOP321_IRQ(16)
+#define IRQ_IOP321_BIU_ERR	IOP321_IRQ(17)
+#define IRQ_IOP321_ATU_ERR	IOP321_IRQ(18)
+#define IRQ_IOP321_MCU_ERR	IOP321_IRQ(19)
+#define IRQ_IOP321_DMA0_ERR	IOP321_IRQ(20)
+#define IRQ_IOP321_DMA1_ERR	IOP321_IRQ(21)
+#define IRQ_IOP321_RSVD_22	IOP321_IRQ(22)
+#define IRQ_IOP321_AA_ERR	IOP321_IRQ(23)
+#define IRQ_IOP321_MSG_ERR	IOP321_IRQ(24)
+#define IRQ_IOP321_SSP		IOP321_IRQ(25)
+#define IRQ_IOP321_RSVD_26	IOP321_IRQ(26)
+#define IRQ_IOP321_XINT0	IOP321_IRQ(27)
+#define IRQ_IOP321_XINT1	IOP321_IRQ(28)
+#define IRQ_IOP321_XINT2	IOP321_IRQ(29)
+#define IRQ_IOP321_XINT3	IOP321_IRQ(30)
+#define IRQ_IOP321_HPI		IOP321_IRQ(31)
+
+#define NR_IOP321_IRQS		(IOP321_IRQ(31) + 1)
+
+#define NR_IRQS			NR_IOP321_IRQS
+
+
+/*
+ * Interrupts available on the IQ80321 board
+ */
+#ifdef CONFIG_ARCH_IQ80321
+
+/*
+ * On board devices
+ */
+#define	IRQ_IQ80321_I82544	IRQ_IOP321_XINT0
+#define IRQ_IQ80321_UART	IRQ_IOP321_XINT1
+
+/*
+ * PCI interrupts
+ */
+#define	IRQ_IQ80321_INTA	IRQ_IOP321_XINT0
+#define	IRQ_IQ80321_INTB	IRQ_IOP321_XINT1
+#define	IRQ_IQ80321_INTC	IRQ_IOP321_XINT2
+#define	IRQ_IQ80321_INTD	IRQ_IOP321_XINT3
+
+#endif // CONFIG_ARCH_IQ80321
+
+#define XSCALE_PMU_IRQ	IRQ_IOP321_CORE_PMU
+

include/asm-arm/arch-iop3xx/iop321.h

+/*
+ * linux/include/asm/arch-iop3xx/iop321.h
+ *
+ * Intel IOP321 Chip definitions
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _IOP321_HW_H_
+#define _IOP321_HW_H_
+
+/*
+ * IOP321 I/O and Mem space regions for PCI autoconfiguration
+ */
+#define	IOP321_PCI_LOWER_IO		0x90000000
+#define	IOP321_PCI_UPPER_IO		0x9000ffff
+#define IOP321_PCI_LOWER_MEM		0x80000000
+#define IOP321_PCI_UPPER_MEM		0x83ffffff
+
+#define IOP321_PCI_WINDOW_SIZE		64 * 0x100000
+
+/*
+ * IOP321 chipset registers
+ */
+#define IOP321_VIRT_MEM_BASE 0xfff00000  /* chip virtual mem address*/
+#define IOP321_PHY_MEM_BASE  0xffffe000  /* chip physical memory address */
+#define IOP321_REG_ADDR(reg) (IOP321_VIRT_MEM_BASE | (reg))
+
+/* Reserved 0x00000000 through 0x000000FF */
+
+/* Address Translation Unit 0x00000100 through 0x000001FF */
+#define IOP321_ATUVID     (volatile u16 *)IOP321_REG_ADDR(0x00000100)
+#define IOP321_ATUDID     (volatile u16 *)IOP321_REG_ADDR(0x00000102)
+#define IOP321_ATUCMD     (volatile u16 *)IOP321_REG_ADDR(0x00000104)
+#define IOP321_ATUSR      (volatile u16 *)IOP321_REG_ADDR(0x00000106)
+#define IOP321_ATURID     (volatile u8  *)IOP321_REG_ADDR(0x00000108)
+#define IOP321_ATUCCR     (volatile u32 *)IOP321_REG_ADDR(0x00000109)
+#define IOP321_ATUCLSR    (volatile u8  *)IOP321_REG_ADDR(0x0000010C)
+#define IOP321_ATULT      (volatile u8  *)IOP321_REG_ADDR(0x0000010D)
+#define IOP321_ATUHTR     (volatile u8  *)IOP321_REG_ADDR(0x0000010E)
+#define IOP321_ATUBIST    (volatile u8  *)IOP321_REG_ADDR(0x0000010F)
+#define IOP321_IABAR0     (volatile u32 *)IOP321_REG_ADDR(0x00000110)
+#define IOP321_IAUBAR0    (volatile u32 *)IOP321_REG_ADDR(0x00000114)
+#define IOP321_IABAR1     (volatile u32 *)IOP321_REG_ADDR(0x00000118)
+#define IOP321_IAUBAR1    (volatile u32 *)IOP321_REG_ADDR(0x0000011C)
+#define IOP321_IABAR2     (volatile u32 *)IOP321_REG_ADDR(0x00000120)
+#define IOP321_IAUBAR2    (volatile u32 *)IOP321_REG_ADDR(0x00000124)
+#define IOP321_ASVIR      (volatile u16 *)IOP321_REG_ADDR(0x0000012C)
+#define IOP321_ASIR       (volatile u16 *)IOP321_REG_ADDR(0x0000012E)
+#define IOP321_ERBAR      (volatile u32 *)IOP321_REG_ADDR(0x00000130)
+/* Reserved 0x00000134 through 0x0000013B */
+#define IOP321_ATUILR     (volatile u8  *)IOP321_REG_ADDR(0x0000013C)
+#define IOP321_ATUIPR     (volatile u8  *)IOP321_REG_ADDR(0x0000013D)
+#define IOP321_ATUMGNT    (volatile u8  *)IOP321_REG_ADDR(0x0000013E)
+#define IOP321_ATUMLAT    (volatile u8  *)IOP321_REG_ADDR(0x0000013F)
+#define IOP321_IALR0      (volatile u32 *)IOP321_REG_ADDR(0x00000140)
+#define IOP321_IATVR0     (volatile u32 *)IOP321_REG_ADDR(0x00000144)
+#define IOP321_ERLR       (volatile u32 *)IOP321_REG_ADDR(0x00000148)
+#define IOP321_ERTVR      (volatile u32 *)IOP321_REG_ADDR(0x0000014C)
+#define IOP321_IALR1      (volatile u32 *)IOP321_REG_ADDR(0x00000150)
+#define IOP321_IALR2      (volatile u32 *)IOP321_REG_ADDR(0x00000154)
+#define IOP321_IATVR2     (volatile u32 *)IOP321_REG_ADDR(0x00000158)
+#define IOP321_OIOWTVR    (volatile u32 *)IOP321_REG_ADDR(0x0000015C)
+#define IOP321_OMWTVR0    (volatile u32 *)IOP321_REG_ADDR(0x00000160)
+#define IOP321_OUMWTVR0   (volatile u32 *)IOP321_REG_ADDR(0x00000164)
+#define IOP321_OMWTVR1    (volatile u32 *)IOP321_REG_ADDR(0x00000168)
+#define IOP321_OUMWTVR1   (volatile u32 *)IOP321_REG_ADDR(0x0000016C)
+/* Reserved 0x00000170 through 0x00000177*/
+#define IOP321_OUDWTVR    (volatile u32 *)IOP321_REG_ADDR(0x00000178)
+/* Reserved 0x0000017C through 0x0000017F*/
+#define IOP321_ATUCR      (volatile u32 *)IOP321_REG_ADDR(0x00000180)
+#define IOP321_PCSR       (volatile u32 *)IOP321_REG_ADDR(0x00000184)
+#define IOP321_ATUISR     (volatile u32 *)IOP321_REG_ADDR(0x00000188)
+#define IOP321_ATUIMR     (volatile u32 *)IOP321_REG_ADDR(0x0000018C)
+#define IOP321_IABAR3     (volatile u32 *)IOP321_REG_ADDR(0x00000190)
+#define IOP321_IAUBAR3    (volatile u32 *)IOP321_REG_ADDR(0x00000194)
+#define IOP321_IALR3      (volatile u32 *)IOP321_REG_ADDR(0x00000198)
+#define IOP321_IATVR3     (volatile u32 *)IOP321_REG_ADDR(0x0000019C)
+/* Reserved 0x000001A0 through 0x000001A3*/
+#define IOP321_OCCAR      (volatile u32 *)IOP321_REG_ADDR(0x000001A4)
+/* Reserved 0x000001A8 through 0x000001AB*/
+#define IOP321_OCCDR      (volatile u32 *)IOP321_REG_ADDR(0x000001AC)
+/* Reserved 0x000001B0 through 0x000001BB*/
+#define IOP321_PDSCR      (volatile u32 *)IOP321_REG_ADDR(0x000001BC)
+#define IOP321_PMCAPID    (volatile u8  *)IOP321_REG_ADDR(0x000001C0)
+#define IOP321_PMNEXT     (volatile u8  *)IOP321_REG_ADDR(0x000001C1)
+#define IOP321_APMCR      (volatile u16 *)IOP321_REG_ADDR(0x000001C2)
+#define IOP321_APMCSR     (volatile u16 *)IOP321_REG_ADDR(0x000001C4)
+/* Reserved 0x000001C6 through 0x000001DF */
+#define IOP321_PCIXCAPID  (volatile u8  *)IOP321_REG_ADDR(0x000001E0)
+#define IOP321_PCIXNEXT   (volatile u8  *)IOP321_REG_ADDR(0x000001E1)
+#define IOP321_PCIXCMD    (volatile u16 *)IOP321_REG_ADDR(0x000001E2)
+#define IOP321_PCIXSR     (volatile u32 *)IOP321_REG_ADDR(0x000001E4)
+#define IOP321_PCIIRSR    (volatile u32 *)IOP321_REG_ADDR(0x000001EC)
+
+/* Messaging Unit 0x00000300 through 0x000003FF */
+/* DMA Controller 0x00000400 through 0x000004FF */
+/* Memory controller 0x00000500 through 0x0005FF */
+/* Peripheral bus interface unit 0x00000680 through 0x0006FF */
+/* Peripheral performance monitoring unit 0x00000700 through 0x00077F */
+/* Internal arbitration unit 0x00000780 through 0x0007BF */
+
+/* Interrupt Controller */
+#define IOP321_INTCTL     (volatile u32 *)IOP321_REG_ADDR(0x000007D0)
+#define IOP321_INTSTR     (volatile u32 *)IOP321_REG_ADDR(0x000007D4)
+#define IOP321_IINTSRC    (volatile u32 *)IOP321_REG_ADDR(0x000007D8)
+#define IOP321_FINTSRC    (volatile u32 *)IOP321_REG_ADDR(0x000007DC)
+
+/* Timers */
+
+#define IOP321_TU_TMR0		(volatile u32 *)IOP321_REG_ADDR(0x000007E0)
+#define IOP321_TU_TMR1		(volatile u32 *)IOP321_REG_ADDR(0x000007E4)
+
+#define IOP321_TMR_TC		0x01
+#define	IOP321_TMR_EN		0x02
+#define IOP321_TMR_RELOAD	0x04
+#define	IOP321_TMR_PRIVILEGED	0x09
+
+#define	IOP321_TMR_RATIO_1_1	0x00
+#define	IOP321_TMR_RATIO_4_1	0x10
+#define	IOP321_TMR_RATIO_8_1	0x20
+#define	IOP321_TMR_RATIO_16_1	0x30
+
+#define IOP321_TU_TCR0    (volatile u32 *)IOP321_REG_ADDR(0x000007E8)
+#define IOP321_TU_TCR1    (volatile u32 *)IOP321_REG_ADDR(0x000007EC)
+#define IOP321_TU_TRR0    (volatile u32 *)IOP321_REG_ADDR(0x000007F0)
+#define IOP321_TU_TRR1    (volatile u32 *)IOP321_REG_ADDR(0x000007F4)
+#define IOP321_TU_TISR    (volatile u32 *)IOP321_REG_ADDR(0x000007F8)
+#define IOP321_TU_WDTCR   (volatile u32 *)IOP321_REG_ADDR(0x000007FC)
+
+/* Application accelerator unit 0x00000800 - 0x000008FF */
+#define IOP321_AAUACR     (volatile u32 *)IOP321_REG_ADDR(0x00000800)
+#define IOP321_AAUASR     (volatile u32 *)IOP321_REG_ADDR(0x00000804)
+#define IOP321_AAUANDAR   (volatile u32 *)IOP321_REG_ADDR(0x0000080C)
+
+/* SSP serial port unit 0x00001600 - 0x0000167F */
+/* I2C bus interface unit 0x00001680 - 0x000016FF */
+#endif // _IOP321_HW_H_

include/asm-arm/arch-iop3xx/iq80321.h

+/*
+ * linux/include/asm/arch-iop3xx/iq80321.h
+ *
+ * Intel IQ-80321 evaluation board registers
+ */
+
+#ifndef _IQ80321_H_
+#define _IQ80321_H_
+
+#define IQ80321_RAMBASE      0xa0000000
+#define IQ80321_UART1        0xfe800000    /* UART #1 */
+#define IQ80321_7SEG_1       0xfe840000    /* 7-Segment MSB */
+#define IQ80321_7SEG_0       0xfe850000    /* 7-Segment LSB (WO) */
+#define IQ80321_ROTARY_SW    0xfe8d0000    /* Rotary Switch */
+#define IQ80321_BATT_STAT    0xfe8f0000    /* Battery Status */
+
+#endif	// _IQ80321_H_

include/asm-arm/arch-iop3xx/irqs.h

 /*
  * linux/include/asm-arm/arch-iop3xx/irqs.h
  *
- * Author:	Nicolas Pitre
  * Copyright:	(C) 2001 MontaVista Software Inc.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  *
- * 06/13/01: Added 80310 on-chip interrupt sources <dsaxena@mvista.com>
  *
  */
-#include <linux/config.h>
 
 /*
- * XS80200 specific IRQs
+ * Whic iop3xx implementation is this?
  */
-#define IRQ_XS80200_BCU		0	/* Bus Control Unit */
-#define IRQ_XS80200_PMU		1	/* Performance Monitoring Unit */
-#define IRQ_XS80200_EXTIRQ	2	/* external IRQ signal */
-#define IRQ_XS80200_EXTFIQ	3	/* external IRQ signal */
+#ifdef CONFIG_ARCH_IOP310
 
-#define NR_XS80200_IRQS		4
+#include "iop310-irqs.h"
 
-#define XSCALE_PMU_IRQ		IRQ_XS80200_PMU
+#else
 
-/*
- * IOP80310 chipset interrupts
- */
-#define IOP310_IRQ_OFS		NR_XS80200_IRQS
-#define IOP310_IRQ(x)		(IOP310_IRQ_OFS + (x))
-
-/*
- * On FIQ1ISR register
- */
-#define IRQ_IOP310_DMA0		IOP310_IRQ(0)	/* DMA Channel 0 */
-#define IRQ_IOP310_DMA1		IOP310_IRQ(1)	/* DMA Channel 1 */
-#define IRQ_IOP310_DMA2		IOP310_IRQ(2)	/* DMA Channel 2 */
-#define IRQ_IOP310_PMON		IOP310_IRQ(3)	/* Bus performance Unit */
-#define IRQ_IOP310_AAU		IOP310_IRQ(4)	/* Application Accelator Unit */
-
-/*
- * On FIQ2ISR register
- */
-#define IRQ_IOP310_I2C		IOP310_IRQ(5)	/* I2C unit */
-#define IRQ_IOP310_MU		IOP310_IRQ(6)	/* messaging unit */
-
-#define NR_IOP310_IRQS		(IOP310_IRQ(6) + 1)
-
-#define NR_IRQS			NR_IOP310_IRQS
-
-
-/*
- * Interrupts available on the Cyclone IQ80310 board
- */
-#ifdef CONFIG_ARCH_IQ80310
-
-#define IQ80310_IRQ_OFS		NR_IOP310_IRQS
-#define IQ80310_IRQ(y)		((IQ80310_IRQ_OFS) + (y))
-
-#define IRQ_IQ80310_TIMER	IQ80310_IRQ(0)	/* Timer Interrupt */
-#define IRQ_IQ80310_I82559	IQ80310_IRQ(1)	/* I82559 Ethernet Interrupt */
-#define IRQ_IQ80310_UART1	IQ80310_IRQ(2)	/* UART1 Interrupt */
-#define IRQ_IQ80310_UART2	IQ80310_IRQ(3)	/* UART2 Interrupt */
-#define IRQ_IQ80310_INTD	IQ80310_IRQ(4)	/* PCI INTD */
-
-
-/*
- * ONLY AVAILABLE ON REV F OR NEWER BOARDS!
- */
-#define	IRQ_IQ80310_INTA	IQ80310_IRQ(5)	/* PCI INTA */
-#define	IRQ_IQ80310_INTB	IQ80310_IRQ(6)	/* PCI INTB */
-#define	IRQ_IQ80310_INTC	IQ80310_IRQ(7)	/* PCI INTC */
-
-#undef	NR_IRQS
-#define NR_IRQS			(IQ80310_IRQ(7) + 1)
+#include "iop321-irqs.h"
 
-#endif // CONFIG_ARCH_IQ80310
+#endif
 

include/asm-arm/arch-iop3xx/memory.h

@@ -7,6 +7,7 @@
 
 #include <linux/config.h>
 #include <asm/arch/iop310.h>
+#include <asm/arch/iop321.h>
 
 /*
  * Task size: 3GB
@@ -47,9 +48,19 @@
  */
 #define __virt_to_bus__is_a_macro
 #define __bus_to_virt__is_a_macro
+
+#ifdef CONFIG_ARCH_IOP310
+
 #define __virt_to_bus(x)	(((__virt_to_phys(x)) & ~(*IOP310_SIATVR)) | ((*IOP310_SIABAR) & 0xfffffff0))
 #define __bus_to_virt(x)    (__phys_to_virt(((x) & ~(*IOP310_SIALR)) | ( *IOP310_SIATVR)))
 
+#elif defined(CONFIG_ARCH_IOP321)
+
+#define __virt_to_bus(x)	(((__virt_to_phys(x)) & ~(*IOP321_IATVR2)) | ((*IOP321_IABAR2) & 0xfffffff0))
+#define __bus_to_virt(x)    (__phys_to_virt(((x) & ~(*IOP321_IALR2)) | ( *IOP321_IATVR2)))
+
+#endif
+
 /* boot mem allocate global pointer for MU circular queues QBAR */
 #ifdef CONFIG_IOP3XX_MU
 extern void *mu_mem;

include/asm-arm/arch-iop3xx/serial.h

@@ -29,6 +29,17 @@
 
 #endif // CONFIG_ARCH_IQ80310
 
+#ifdef CONFIG_ARCH_IQ80321
+
+#define IRQ_UART1	IRQ_IQ80321_UART
+
+#define RS_TABLE_SIZE 1
+
+#define STD_SERIAL_PORT_DEFNS			\
+       /* UART CLK      PORT        IRQ        FLAGS        */			\
+	{ 0, BASE_BAUD, 0xfe800000, IRQ_UART1, STD_COM_FLAGS },  /* ttyS0 */
+#endif // CONFIG_ARCH_IQ80321
+
 
 #define EXTRA_SERIAL_PORT_DEFNS
 

include/asm-arm/arch-iop3xx/timex.h

@@ -14,7 +14,11 @@
 #else
 /* This is for the underlying xs80200 PMU clock. We run the core @ 733MHz */
 #define CLOCK_TICK_RATE	733000000
-#endif
+#endif // IQ80310
+
+#elif defined(CONFIG_ARCH_IQ80321)
+
+#define CLOCK_TICK_RATE 200000000
 
 #else
 

include/asm-arm/arch-iop3xx/uncompress.h

@@ -2,10 +2,13 @@
  *  linux/include/asm-arm/arch-iop80310/uncompress.h
  */
 #include <linux/config.h>
+#include <linux/serial_reg.h>
+#include <asm/hardware.h>
 
 #ifdef CONFIG_ARCH_IQ80310
-#define UART1_BASE    ((volatile unsigned char *)0xfe800000)
-#define UART2_BASE    ((volatile unsigned char *)0xfe810000)
+#define UART2_BASE    ((volatile unsigned char *)IQ80310_UART2)
+#elif defined(CONFIG_ARCH_IQ80321)
+#define UART2_BASE    ((volatile unsigned char *)IQ80321_UART1)
 #endif
 
 static __inline__ void putc(char c)

include/asm-arm/mach/pci.h

@@ -56,6 +56,10 @@ extern int iop310_setup(int nr, struct pci_sys_data *);
 extern struct pci_bus *iop310_scan_bus(int nr, struct pci_sys_data *);
 extern void iop310_init(void);
 
+extern int iop321_setup(int nr, struct pci_sys_data *);
+extern struct pci_bus *iop321_scan_bus(int nr, struct pci_sys_data *);
+extern void iop321_init(void);
+
 extern int dc21285_setup(int nr, struct pci_sys_data *);
 extern struct pci_bus *dc21285_scan_bus(int nr, struct pci_sys_data *);
 extern void dc21285_preinit(void);