arm64: dts: marvell: Add support for Marvell CN9131-DB

Extend the support of the CN9130 by adding an external CP115.

The last number indicates how many external CP115 are used.

New available interfaces:
* CP1 CRYPTO-0 (disabled)
* CP1 ETH-0 (SFI, problem with the SFP cage, disabled)
* CP1 GPIO-1
* CP1 GPIO-2
* CP1 I2C-0
* CP1 PCIe-0 x2
* CP1 SPI-1
* CP1 SATA-0-1
* CP1 USB3-1
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

arch/arm64/boot/dts/marvell/Makefile

@@ -11,3 +11,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb

arch/arm64/boot/dts/marvell/cn9131-db.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9131-DB board.
+ */
+
+#include "cn9130-db.dts"
+
+/ {
+	model = "Marvell Armada CN9131-DB";
+	compatible = "marvell,cn9131", "marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	aliases {
+		gpio3 = &cp1_gpio1;
+		gpio4 = &cp1_gpio2;
+		ethernet3 = &cp1_eth0;
+		ethernet4 = &cp1_eth1;
+	};
+
+	cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&cp1_xhci0_vbus_pins>;
+		regulator-name = "cp1-xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp1_usb3_0_phy0: cp1_usb3_phy0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp1_reg_usb3_vbus0>;
+	};
+
+	cp1_sfp_eth1: sfp-eth1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp1_i2c0>;
+		los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cp1_sfp_pins>;
+		/*
+		 * SFP cages are unconnected on early PCBs because of an the I2C
+		 * lanes not being connected. Prevent the port for being
+		 * unusable by disabling the SFP node.
+		 */
+		status = "disabled";
+	};
+};
+
+/*
+ * Instantiate the first slave CP115
+ */
+
+#define CP11X_NAME		cp1
+#define CP11X_BASE		f4000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE	f4600000
+#define CP11X_PCIE1_BASE	f4620000
+#define CP11X_PCIE2_BASE	f4640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp1_crypto {
+	status = "disabled";
+};
+
+&cp1_ethernet {
+	status = "okay";
+};
+
+/* CON50 */
+&cp1_eth0 {
+	status = "disabled";
+	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp1_comphy4 0>;
+	managed = "in-band-status";
+	sfp = <&cp1_sfp_eth1>;
+};
+
+&cp1_gpio1 {
+	status = "okay";
+};
+
+&cp1_gpio2 {
+	status = "okay";
+};
+
+&cp1_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+/* CON40 */
+&cp1_pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_pcie_reset_pins>;
+	num-lanes = <2>;
+	num-viewport = <8>;
+	marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp1_comphy0 0
+		&cp1_comphy1 0>;
+};
+
+&cp1_sata0 {
+	status = "okay";
+
+	/* CON32 */
+	sata-port@1 {
+		/* Generic PHY, providing serdes lanes */
+		phys = <&cp1_comphy5 1>;
+	};
+};
+
+/* U24 */
+&cp1_spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_spi0_pins>;
+	reg = <0x700680 0x50>;
+
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		/* On-board MUX does not allow higher frequencies */
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot-1";
+				reg = <0x0 0x200000>;
+			};
+
+			partition@400000 {
+				label = "Filesystem-1";
+				reg = <0x200000 0xe00000>;
+			};
+		};
+	};
+
+};
+
+&cp1_syscon0 {
+	cp1_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+
+		cp1_i2c0_pins: cp1-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp1_spi0_pins: cp1-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+		cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
+			marvell,pins = "mpp3";
+			marvell,function = "gpio";
+		};
+		cp1_sfp_pins: sfp-pins {
+			marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
+			marvell,function = "gpio";
+		};
+		cp1_pcie_reset_pins: cp1-pcie-reset-pins {
+			marvell,pins = "mpp0";
+			marvell,function = "gpio";
+		};
+	};
+};
+
+/* CON58 */
+&cp1_usb3_1 {
+	status = "okay";
+	usb-phy = <&cp1_usb3_0_phy0>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp1_comphy3 1>;
+	phy-names = "usb";
+};