net: mvneta: use resolved link config in mac_link_up()

Convert the Marvell mvneta ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/mvneta.c

@@ -3830,13 +3830,9 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 	new_clk = gmac_clk & ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
 	new_an = gmac_an & ~(MVNETA_GMAC_INBAND_AN_ENABLE |
 			     MVNETA_GMAC_INBAND_RESTART_AN |
-			     MVNETA_GMAC_CONFIG_MII_SPEED |
-			     MVNETA_GMAC_CONFIG_GMII_SPEED |
 			     MVNETA_GMAC_AN_SPEED_EN |
 			     MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL |
-			     MVNETA_GMAC_CONFIG_FLOW_CTRL |
 			     MVNETA_GMAC_AN_FLOW_CTRL_EN |
-			     MVNETA_GMAC_CONFIG_FULL_DUPLEX |
 			     MVNETA_GMAC_AN_DUPLEX_EN);
 
 	/* Even though it might look weird, when we're configured in
@@ -3851,24 +3847,20 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 
 	if (phylink_test(state->advertising, Pause))
 		new_an |= MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL;
-	if (state->pause & MLO_PAUSE_TXRX_MASK)
-		new_an |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
 
 	if (!phylink_autoneg_inband(mode)) {
-		/* Phy or fixed speed */
-		if (state->duplex)
-			new_an |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
-
-		if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
-			new_an |= MVNETA_GMAC_CONFIG_GMII_SPEED;
-		else if (state->speed == SPEED_100)
-			new_an |= MVNETA_GMAC_CONFIG_MII_SPEED;
+		/* Phy or fixed speed - nothing to do, leave the
+		 * configured speed, duplex and flow control as-is.
+		 */
 	} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
 		/* SGMII mode receives the state from the PHY */
 		new_ctrl2 |= MVNETA_GMAC2_INBAND_AN_ENABLE;
 		new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
 		new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
-				     MVNETA_GMAC_FORCE_LINK_PASS)) |
+				     MVNETA_GMAC_FORCE_LINK_PASS |
+				     MVNETA_GMAC_CONFIG_MII_SPEED |
+				     MVNETA_GMAC_CONFIG_GMII_SPEED |
+				     MVNETA_GMAC_CONFIG_FULL_DUPLEX)) |
 			 MVNETA_GMAC_INBAND_AN_ENABLE |
 			 MVNETA_GMAC_AN_SPEED_EN |
 			 MVNETA_GMAC_AN_DUPLEX_EN;
@@ -3877,7 +3869,8 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 		new_ctrl0 |= MVNETA_GMAC0_PORT_1000BASE_X;
 		new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
 		new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
-				     MVNETA_GMAC_FORCE_LINK_PASS)) |
+				     MVNETA_GMAC_FORCE_LINK_PASS |
+				     MVNETA_GMAC_CONFIG_MII_SPEED)) |
 			 MVNETA_GMAC_INBAND_AN_ENABLE |
 			 MVNETA_GMAC_CONFIG_GMII_SPEED |
 			 /* The MAC only supports FD mode */
@@ -3977,8 +3970,36 @@ static void mvneta_mac_link_up(struct phylink_config *config,
 
 	if (!phylink_autoneg_inband(mode)) {
 		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
-		val &= ~MVNETA_GMAC_FORCE_LINK_DOWN;
+		val &= ~(MVNETA_GMAC_FORCE_LINK_DOWN |
+			 MVNETA_GMAC_CONFIG_MII_SPEED |
+			 MVNETA_GMAC_CONFIG_GMII_SPEED |
+			 MVNETA_GMAC_CONFIG_FLOW_CTRL |
+			 MVNETA_GMAC_CONFIG_FULL_DUPLEX);
 		val |= MVNETA_GMAC_FORCE_LINK_PASS;
+
+		if (speed == SPEED_1000 || speed == SPEED_2500)
+			val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
+		else if (speed == SPEED_100)
+			val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+
+		if (duplex == DUPLEX_FULL)
+			val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+		if (tx_pause || rx_pause)
+			val |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
+		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+	} else {
+		/* When inband doesn't cover flow control or flow control is
+		 * disabled, we need to manually configure it. This bit will
+		 * only have effect if MVNETA_GMAC_AN_FLOW_CTRL_EN is unset.
+		 */
+		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+		val &= ~MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
+		if (tx_pause || rx_pause)
+			val |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
 		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
 	}