Kconfig 107 KB
Newer Older
1

2 3 4
#
# Network device configuration
#
5 6 7 8 9 10 11 12 13 14

config NETDEVICES
	depends on NET
	bool "Network device support"
	---help---
	  You can say N here if you don't intend to connect your Linux box to
	  any other computer at all or if all your connections will be over a
	  telephone line with a modem either via UUCP (UUCP is a protocol to
	  forward mail and news between unix hosts over telephone lines; read
	  the UUCP-HOWTO, available from
15
	  <http://www.tldp.org/docs.html#howto>) or dialing up a shell
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
	  account or a BBS, even using term (term is a program which gives you
	  almost full Internet connectivity if you have a regular dial up
	  shell account on some Internet connected Unix computer. Read
	  <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>).

	  You'll have to say Y if your computer contains a network card that
	  you want to use under Linux (make sure you know its name because you
	  will be asked for it and read the Ethernet-HOWTO (especially if you
	  plan to use more than one network card under Linux)) or if you want
	  to use SLIP (Serial Line Internet Protocol is the protocol used to
	  send Internet traffic over telephone lines or null modem cables) or
	  CSLIP (compressed SLIP) or PPP (Point to Point Protocol, a better
	  and newer replacement for SLIP) or PLIP (Parallel Line Internet
	  Protocol is mainly used to create a mini network by connecting the
	  parallel ports of two local machines) or AX.25/KISS (protocol for
	  sending Internet traffic over amateur radio links).

	  Make sure to read the NET-3-HOWTO. Eventually, you will have to read
	  Olaf Kirch's excellent and free book "Network Administrator's
35
	  Guide", to be found in <http://www.tldp.org/docs.html#guide>. If
36 37 38 39 40
	  unsure, say Y.

if NETDEVICES
	source "drivers/net/arcnet/Kconfig"
endif
41 42 43 44 45 46 47 48 49 50 51 52 53

config DUMMY
	tristate "Dummy net driver support"
	depends on NETDEVICES
	---help---
	  This is essentially a bit-bucket device (i.e. traffic you send to
	  this device is consigned into oblivion) with a configurable IP
	  address. It is most commonly used in order to make your currently
	  inactive SLIP address seem like a real address for local programs.
	  If you use SLIP or PPP, you might want to say Y here. Since this
	  thing often comes in handy, the default is Y. It won't enlarge your
	  kernel either. What a deal. Read about it in the Network
	  Administrator's Guide, available from
54
	  <http://www.tldp.org/docs.html#guide>.
55 56 57 58

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  The module
59
	  will be called dummy.  If you want to use more than one dummy
60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83
	  device at a time, you need to compile this driver as a module.
	  Instead of 'dummy', the devices will then be called 'dummy0',
	  'dummy1' etc.

config BONDING
	tristate "Bonding driver support"
	depends on NETDEVICES
	---help---
	  Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	  Channels together. This is called 'Etherchannel' by Cisco,
	  'Trunking' by Sun, and 'Bonding' in Linux.

	  If you have two Ethernet connections to some other computer, you can
	  make them behave like one double speed connection using this driver.
	  Naturally, this has to be supported at the other end as well, either
	  with a similar Bonding Linux driver, a Cisco 5500 switch or a
	  SunTrunking SunSoft driver.

	  This is similar to the EQL driver, but it merges Ethernet segments
	  instead of serial lines.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  The module
84
	  will be called bonding.
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

config EQUALIZER
	tristate "EQL (serial line load balancing) support"
	depends on NETDEVICES
	---help---
	  If you have two serial connections to some other computer (this
	  usually requires two modems and two telephone lines) and you use
	  SLIP (the protocol for sending Internet traffic over telephone
	  lines) or PPP (a better SLIP) on them, you can make them behave like
	  one double speed connection using this driver.  Naturally, this has
	  to be supported at the other end as well, either with a similar EQL
	  Linux driver or with a Livingston Portmaster 2e.

	  Say Y if you want this and read
	  <file:Documentation/networking/eql.txt>.  You may also want to read
	  section 6.2 of the NET-3-HOWTO, available from
101
	  <http://www.tldp.org/docs.html#howto>.
102 103 104

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
105
	  The module will be called eql.  If you want to compile it as a
106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
	  module, say M here and read <file:Documentation/modules.txt>.  If
	  unsure, say N.

config TUN
	tristate "Universal TUN/TAP device driver support"
	depends on NETDEVICES
	---help---
	  TUN/TAP provides packet reception and transmission for user space
	  programs.  It can be viewed as a simple Point-to-Point or Ethernet
	  device, which instead of receiving packets from a physical media,
	  receives them from user space program and instead of sending packets
	  via physical media writes them to the user space program.

	  When a program opens /dev/net/tun, driver creates and registers
	  corresponding net device tunX or tapX.  After a program closed above
	  devices, driver will automatically delete tunXX or tapXX device and
	  all routes corresponding to it.

	  Please read <file:Documentation/networking/tuntap.txt> for more
	  information.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
129
	  The module will be called tun.  If you want to compile it as a
130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153
	  module, say M here and read <file:Documentation/modules.txt>.

	  If you don't know what to use this for, you don't need it.

config ETHERTAP
	tristate "Ethertap network tap (OBSOLETE)"
	depends on NETDEVICES && EXPERIMENTAL
	---help---
	  If you say Y here (and have said Y to "Kernel/User network link
	  driver", above) and create a character special file /dev/tap0 with
	  major number 36 and minor number 16 using mknod ("man mknod"), you
	  will be able to have a user space program read and write raw
	  Ethernet frames from/to that special file.  tap0 can be configured
	  with ifconfig and route like any other Ethernet device but it is not
	  connected to any physical LAN; everything written by the user to
	  /dev/tap0 is treated by the kernel as if it had come in from a LAN
	  to the device tap0; everything the kernel wants to send out over the
	  device tap0 can instead be read by the user from /dev/tap0: the user
	  mode program replaces the LAN that would be attached to an ordinary
	  Ethernet device. Please read the file
	  <file:Documentation/networking/ethertap.txt> for more information.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
154
	  The module will be called ethertap. If you want to compile it as a
155 156 157 158 159 160
	  module, say M here and read <file:Documentation/modules.txt>.

	  If you don't know what to use this for, you don't need it.

config NET_SB1000
	tristate "General Instruments Surfboard 1000"
161
	depends on NETDEVICES && PNP
162 163 164 165 166 167 168 169 170
	---help---
	  This is a driver for the General Instrument (also known as
	  NextLevel) SURFboard 1000 internal
	  cable modem. This is an ISA card which is used by a number of cable
	  TV companies to provide cable modem access. It's a one-way
	  downstream-only cable modem, meaning that your upstream net link is
	  provided by your regular phone modem.

	  At present this driver only compiles as a module, so say M here if
171
	  you have this card. The module will be called sb1000. Then read
172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208
	  <file:Documentation/networking/README.sb1000> for information on how
	  to use this module, as it needs special ppp scripts for establishing
	  a connection. Further documentation and the necessary scripts can be
	  found at:

	  <http://www.jacksonville.net/~fventuri/>
	  <http://home.adelphia.net/~siglercm/sb1000.html>
	  <http://linuxpower.cx/~cable/>

	  If you don't have this card, of course say N.

#
#	Ethernet
#

menu "Ethernet (10 or 100Mbit)"
	depends on NETDEVICES

config NET_ETHERNET
	bool "Ethernet (10 or 100Mbit)"
	---help---
	  Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
	  type of Local Area Network (LAN) in universities and companies.

	  Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
	  coaxial cable, linking computers in a chain), 10BASE-T or twisted
	  pair (10 Mbps over twisted pair cable, linking computers to central
	  hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
	  100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
	  100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
	  cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
	  [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
	  Ethernet (1 Gbps over optical fiber or short copper links).

	  If your Linux machine will be connected to an Ethernet and you have
	  an Ethernet network interface card (NIC) installed in your computer,
	  say Y here and read the Ethernet-HOWTO, available from
209
	  <http://www.tldp.org/docs.html#howto>. You will then also have
210 211 212 213 214 215
	  to say Y to the driver for your particular NIC.

	  Note that the answer to this question won't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about Ethernet network cards. If unsure, say N.

216
config MII
217
	tristate "Generic Media Independent Interface device support"
218 219 220 221 222 223
	depends on NET_ETHERNET
	help
	  Most ethernet controllers have MII transceiver either as an external
	  or internal device.  It is safe to say Y or M here even if your
	  ethernet card lack MII.

224
source "drivers/net/arm/Kconfig"
225 226 227

config MACE
	tristate "MACE (Power Mac ethernet) support"
228
	depends on NET_ETHERNET && PPC_PMAC
229 230 231 232 233
	help
	  Power Macintoshes and clones with Ethernet built-in on the
	  motherboard will usually use a MACE (Medium Access Control for
	  Ethernet) interface. Say Y to include support for the MACE chip.

234
	  This driver is also available as a module called mace ( = code
235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config MACE_AAUI_PORT
	bool "Use AAUI port instead of TP by default"
	depends on MACE
	help
	  Some Apple machines (notably the Apple Network Server) which use the
	  MACE ethernet chip have an Apple AUI port (small 15-pin connector),
	  instead of an 8-pin RJ45 connector for twisted-pair ethernet.  Say
	  Y here if you have such a machine.  If unsure, say N.
	  The driver will default to AAUI on ANS anyway, and if you use it as
	  a module, you can provide the port_aaui=0|1 to force the driver.

config BMAC
	tristate "BMAC (G3 ethernet) support"
252
	depends on NET_ETHERNET && PPC_PMAC
253 254 255 256
	help
	  Say Y for support of BMAC Ethernet interfaces. These are used on G3
	  computers.

257
	  This driver is also available as a module called bmac ( = code
258 259 260 261 262 263 264 265 266 267
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config OAKNET
	tristate "National DP83902AV (Oak ethernet) support"
	depends on NET_ETHERNET && PPC
	help
	  Say Y if your machine has this type of Ethernet network card.

268
	  This driver is also available as a module called oaknet ( = code
269 270 271 272 273 274 275 276 277 278 279 280 281
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config ARIADNE
	tristate "Ariadne support"
	depends on NET_ETHERNET && ZORRO
	help
	  If you have a Village Tronic Ariadne Ethernet adapter, say Y.
	  Otherwise, say N.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you
282
	  want). The module is called ariadne. If you want to compile it as
283 284 285 286 287 288 289 290 291 292 293
	  a module, say M here and read <file:Documentation/modules.txt>.

config A2065
	tristate "A2065 support"
	depends on NET_ETHERNET && ZORRO
	help
	  If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
	  say N.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you
294
	  want). The module is called a2065. If you want to compile it as a
295 296 297 298 299 300 301 302 303 304
	  module, say M here and read <file:Documentation/modules.txt>.

config HYDRA
	tristate "Hydra support"
	depends on NET_ETHERNET && ZORRO
	help
	  If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you
305
	  want). The module is called hydra. If you want to compile it as a
306 307
	  module, say M here and read <file:Documentation/modules.txt>.

308 309 310 311 312 313 314 315 316 317 318 319 320 321
config ZORRO8390
	tristate "Zorro NS8390-based Ethernet support"
	depends on NET_ETHERNET && ZORRO
	help
	  This driver is for Zorro Ethernet cards using an NS8390-compatible
	  chipset, like the Village Tronic Ariadne II and the Individual
	  Computers X-Surf Ethernet cards. If you have such a card, say Y.
	  Otherwise, say N.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module is called zorro8390. If you want to compile it as
	  a module, say M here and read <file:Documentation/modules.txt>.

322 323 324 325 326 327 328 329 330
config APNE
	tristate "PCMCIA NE2000 support"
	depends on NETDEVICES && AMIGA_PCMCIA
	help
	  If you have a PCMCIA NE2000 compatible adapter, say Y.  Otherwise,
	  say N.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you
331
	  want). The module is called apne. If you want to compile it as a
332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349
	  module, say M here and read <file:Documentation/modules.txt>.

config APOLLO_ELPLUS
	tristate "Apollo 3c505 support"
	depends on NETDEVICES && APOLLO
	help
	  Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
	  If you don't have one made for Apollos, you can use one from a PC,
	  except that your Apollo won't be able to boot from it (because the
	  code in the ROM will be for a PC).

config MAC8390
	bool "Macintosh NS 8390 based ethernet cards"
	depends on NETDEVICES && MAC
	help
	  If you want to include a driver to support Nubus or LC-PDS
	  Ethernet cards using an NS8390 chipset or its equivalent, say Y
	  and read the Ethernet-HOWTO, available from
350
	  <http://www.tldp.org/docs.html#howto>.
351 352 353 354 355 356 357 358

config MAC89x0
	tristate "Macintosh CS89x0 based ethernet cards"
	depends on NETDEVICES && MAC
	---help---
	  Support for CS89x0 chipset based Ethernet cards.  If you have a
	  Nubus or LC-PDS network (Ethernet) card of this type, say Y and
	  read the Ethernet-HOWTO, available from
359
	  <http://www.tldp.org/docs.html#howto>.
360 361 362 363 364

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  This module will
365
	  be called mac89x0.
366 367 368 369 370 371 372 373 374

config MACSONIC
	tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
	depends on NETDEVICES && MAC
	---help---
	  Support for NatSemi SONIC based Ethernet devices.  This includes
	  the onboard Ethernet in many Quadras as well as some LC-PDS,
	  a few Nubus and all known Comm Slot Ethernet cards.  If you have
	  one of these say Y and read the Ethernet-HOWTO, available from
375
	  <http://www.tldp.org/docs.html#howto>.
376 377 378 379 380

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  This module will
381
	  be called macsonic.
382 383 384 385 386 387 388 389

config MACMACE
	bool "Macintosh (AV) onboard MACE ethernet (EXPERIMENTAL)"
	depends on NETDEVICES && MAC && EXPERIMENTAL
	help
	  Support for the onboard AMD 79C940 MACE Ethernet controller used in
	  the 660AV and 840AV Macintosh.  If you have one of these Macintoshes
	  say Y and read the Ethernet-HOWTO, available from
390
	  <http://www.tldp.org/docs.html#howto>.
391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471

config MVME147_NET
	tristate "MVME147 (Lance) Ethernet support"
	depends on NETDEVICES && MVME147
	help
	  Support for the on-board Ethernet interface on the Motorola MVME147
	  single-board computer.  Say Y here to include the
	  driver for this chip in your kernel.   If you want to compile it as
	  a module, say M here and read <file:Documentation/modules.txt>.

config MVME16x_NET
	tristate "MVME16x Ethernet support"
	depends on NETDEVICES && MVME16x
	help
	  This is the driver for the Ethernet interface on the Motorola
	  MVME162, 166, 167, 172 and 177 boards.  Say Y here to include the
	  driver for this chip in your kernel.   If you want to compile it as
	  a module, say M here and read <file:Documentation/modules.txt>.

config BVME6000_NET
	tristate "BVME6000 Ethernet support"
	depends on NETDEVICES && BVME6000
	help
	  This is the driver for the Ethernet interface on BVME4000 and
	  BVME6000 VME boards.  Say Y here to include the driver for this chip
	  in your kernel.   If you want to compile it as a module, say M here
	  and read <file:Documentation/modules.txt>.

config ATARILANCE
	tristate "Atari Lance support"
	depends on NETDEVICES && ATARI
	help
	  Say Y to include support for several Atari Ethernet adapters based
	  on the AMD Lance chipset: RieblCard (with or without battery), or
	  PAMCard VME (also the version by Rhotron, with different addresses).

config ATARI_BIONET
	tristate "BioNet-100 support"
	depends on NETDEVICES && ATARI && ATARI_ACSI!=n
	help
	  Say Y to include support for BioData's BioNet-100 Ethernet adapter
	  for the ACSI port. The driver works (has to work...) with a polled
	  I/O scheme, so it's rather slow :-(

config ATARI_PAMSNET
	tristate "PAMsNet support"
	depends on NETDEVICES && ATARI && ATARI_ACSI!=n
	help
	  Say Y to include support for the PAMsNet Ethernet adapter for the
	  ACSI port ("ACSI node"). The driver works (has to work...) with a
	  polled I/O scheme, so it's rather slow :-(

config SUN3LANCE
	tristate "Sun3/Sun3x on-board LANCE support"
	depends on NETDEVICES && (SUN3 || SUN3X)
	help
	  Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
	  featured an AMD Lance 10Mbit Ethernet controller on board; say Y
	  here to compile in the Linux driver for this and enable Ethernet.
	  General Linux information on the Sun 3 and 3x series (now
	  discontinued) is at
	  <http://www.angelfire.com/ca2/tech68k/sun3.html>.

	  If you're not building a kernel for a Sun 3, say N.

config SUN3_82586
	tristate "Sun3 on-board Intel 82586 support"
	depends on NETDEVICES && SUN3
	help
	  This driver enables support for the on-board Intel 82586 based
	  Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards.  Note
	  that this driver does not support 82586-based adapters on additional
	  VME boards.

config HPLANCE
	bool "HP on-board LANCE support"
	depends on NETDEVICES && HP300
	help
	  If you want to use the builtin "LANCE" Ethernet controller on an
	  HP300 machine, say Y here.

472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491
config LASI_82596
	tristate "Lasi ethernet"
	depends on NET_ETHERNET && PARISC && GSC_LASI
	help
	  Say Y here to support the on-board Intel 82596 ethernet controller
	  built into Hewlett-Packard PA-RISC machines.

config MIPS_JAZZ_SONIC
	tristate "MIPS JAZZ onboard SONIC Ethernet support"
	depends on NET_ETHERNET && MIPS_JAZZ
	help
	  This is the driver for the onboard card of MIPS Magnum 4000,
	  Acer PICA, Olivetti M700-10 and a few other identical OEM systems.

config MIPS_GT96100ETH
	bool "MIPS GT96100 Ethernet support"
	depends on NET_ETHERNET && MIPS_GT96100
	help
	  Say Y here to support the Ethernet subsystem on your GT96100 card.

Ralf Bächle's avatar
Ralf Bächle committed
492
config MIPS_AU1X00_ENET
493
	bool "MIPS AU1000 Ethernet support"
Ralf Bächle's avatar
Ralf Bächle committed
494
	depends on NET_ETHERNET && SOC_AU1X00
495
	help
Ralf Bächle's avatar
Ralf Bächle committed
496 497
	  If you have an Alchemy Semi AU1X00 based system
	  say Y.  Otherwise, say N.
498 499 500

config NET_SB1250_MAC
	tristate "SB1250 Ethernet support"
501
	depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC
502 503 504 505 506 507 508

config SGI_IOC3_ETH
	bool "SGI IOC3 Ethernet"
	depends on NET_ETHERNET && (IA64_SGI_SN1 || SGI_IP27)
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
509
	  <http://www.tldp.org/docs.html#howto>.
510

511 512 513 514
config SGI_O2MACE_ETH
	tristate "SGI O2 MACE Fast Ethernet support"
	depends on NET_ETHERNET && SGI_IP32=y

515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534
config STNIC
	tristate "National DP83902AV  support"
	depends on NET_ETHERNET && SUPERH
	help
	  Support for cards based on the National Semiconductor DP83902AV
	  ST-NIC Serial Network Interface Controller for Twisted Pair.  This
	  is a 10Mbit/sec Ethernet controller.  Product overview and specs at
	  <http://www.national.com/pf/DP/DP83902A.html>.

	  If unsure, say N.

config SUNLANCE
	tristate "Sun LANCE support"
	depends on NET_ETHERNET && SBUS
	help
	  This driver supports the "le" interface present on all 32-bit Sparc
	  systems, on some older Ultra systems and as an Sbus option.  These
	  cards are based on the AMD Lance chipset, which is better known
	  via the NE2100 cards.

535
	  This support is also available as a module called sunlance ( =
536 537 538 539 540 541 542 543 544 545 546 547 548
	  code which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config HAPPYMEAL
	tristate "Sun Happy Meal 10/100baseT support"
	depends on NET_ETHERNET && (SBUS || PCI)
	help
	  This driver supports the "hme" interface present on most Ultra
	  systems and as an option on older Sbus systems. This driver supports
	  both PCI and Sbus devices. This driver also supports the "qfe" quad
	  100baseT device available in both PCI and Sbus configurations.

549
	  This support is also available as a module called sunhme ( = code
550 551 552 553 554 555 556 557 558 559 560
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config SUNBMAC
	tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
	depends on NET_ETHERNET && SBUS && EXPERIMENTAL
	help
	  This driver supports the "be" interface available as an Sbus option.
	  This is Sun's older 100baseT Ethernet device.

561
	  This support is also available as a module called sunbmac ( = code
562 563 564 565 566 567 568 569 570 571 572 573
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config SUNQE
	tristate "Sun QuadEthernet support"
	depends on NET_ETHERNET && SBUS
	help
	  This driver supports the "qe" 10baseT Ethernet device, available as
	  an Sbus option. Note that this is not the same as Quad FastEthernet
	  "qfe" which is supported by the Happy Meal driver instead.

574
	  This support is also available as a module called sunqe ( = code
575 576 577 578 579 580 581 582 583 584 585 586 587
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config SUNGEM
	tristate "Sun GEM support"
	depends on NET_ETHERNET && PCI
	help
	  Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0.  See also
	  <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.

config NET_VENDOR_3COM
	bool "3COM cards"
588
	depends on NET_ETHERNET && (ISA || EISA || MCA || PCI)
589 590 591
	help
	  If you have a network (Ethernet) card belonging to this class, say Y
	  and read the Ethernet-HOWTO, available from
592
	  <http://www.tldp.org/docs.html#howto>.
593 594 595 596 597 598 599 600 601 602 603 604

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about 3COM cards. If you say Y, you will be asked for
	  your specific card in the following questions.

config EL1
	tristate "3c501 \"EtherLink\" support"
	depends on NET_VENDOR_3COM && ISA
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
605
	  <http://www.tldp.org/docs.html#howto>.  Also, consider buying a
606 607 608 609 610 611
	  new card, since the 3c501 is slow, broken, and obsolete: you will
	  have problems.  Some people suggest to ping ("man ping") a nearby
	  machine every minute ("man cron") when using this card.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
612
	  The module will be called 3c501.  If you want to compile it as a
613 614 615 616 617 618 619 620 621
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config EL2
	tristate "3c503 \"EtherLink II\" support"
	depends on NET_VENDOR_3COM && ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
622
	  <http://www.tldp.org/docs.html#howto>.
623 624 625

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
626
	  The module will be called 3c503.  If you want to compile it as a
627 628 629 630 631 632 633 634 635 636
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config ELPLUS
	tristate "3c505 \"EtherLink Plus\" support"
	depends on NET_VENDOR_3COM && ISA
	---help---
	  Information about this network (Ethernet) card can be found in
	  <file:Documentation/networking/3c505.txt>.  If you have a card of
	  this type, say Y and read the Ethernet-HOWTO, available from
637
	  <http://www.tldp.org/docs.html#howto>.
638 639 640 641 642

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
643
	  called 3c505.
644 645 646 647 648 649 650

config EL16
	tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
	depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
651
	  <http://www.tldp.org/docs.html#howto>.
652 653 654

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
655
	  The module will be called 3c507.  If you want to compile it as a
656 657 658 659
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config EL3
660
	tristate "3c509/3c529 (MCA)/3c569B (98)/3c579 \"EtherLink III\" support"
661 662 663 664
	depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
	---help---
	  If you have a network (Ethernet) card belonging to the 3Com
	  EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
665
	  from <http://www.tldp.org/docs.html#howto>.
666 667 668 669 670 671 672 673 674

	  If your card is not working you may need to use the DOS
	  setup disk to disable Plug & Play mode, and to select the default
	  media type.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
675
	  called 3c509.
676 677 678 679 680 681 682

config 3C515
	tristate "3c515 ISA \"Fast EtherLink\""
	depends on NET_VENDOR_3COM && (ISA || EISA)
	help
	  If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
	  network card, say Y and read the Ethernet-HOWTO, available from
683
	  <http://www.tldp.org/docs.html#howto>.
684 685 686 687 688

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
689
	  called 3c515.
690 691 692 693 694 695 696

config ELMC
	tristate "3c523 \"EtherLink/MC\" support"
	depends on NET_VENDOR_3COM && MCA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
697
	  <http://www.tldp.org/docs.html#howto>.
698 699 700

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
701
	  The module will be called 3c523.  If you want to compile it as a
702 703 704 705 706 707 708 709 710
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config ELMC_II
	tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
	depends on NET_VENDOR_3COM && MCA && EXPERIMENTAL
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
711
	  <http://www.tldp.org/docs.html#howto>.
712 713 714

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
715
	  The module will be called 3c527.  If you want to compile it as a
716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config VORTEX
	tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
	depends on NET_VENDOR_3COM && (PCI || EISA)
	---help---
	  This option enables driver support for a large number of 10mbps and
	  10/100mbps EISA, PCI and PCMCIA 3Com network cards:

	  "Vortex"    (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
	  "Boomerang" (EtherLink XL 3c900 or 3c905)            PCI
	  "Cyclone"   (3c540/3c900/3c905/3c980/3c575/3c656)    PCI and Cardbus
	  "Tornado"   (3c905)                                  PCI
	  "Hurricane" (3c555/3cSOHO)                           PCI

	  If you have such a card, say Y and read the Ethernet-HOWTO,
733
	  available from <http://www.tldp.org/docs.html#howto>. More
734 735 736 737 738 739 740 741 742
	  specific information is in
	  <file:Documentation/networking/vortex.txt> and in the comments at
	  the beginning of <file:drivers/net/3c59x.c>.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.

743 744 745 746 747 748 749 750 751 752 753 754
config TYPHOON
	tristate "3cr990 series \"Typhoon\" support"
	depends on NET_VENDOR_3COM && PCI
	---help---
	  This option enables driver support for the 3cr990 series of cards:

	  3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
	  3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
	  3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR

	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
755
	  <http://www.tldp.org/docs.html#howto>.
756 757 758 759 760 761 762

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called typhoon.o.  If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

763 764 765 766 767 768
config LANCE
	tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
	depends on NET_ETHERNET && ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
769
	  <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
770 771 772 773 774
	  of this type.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
775
	  recommended.  The module will be called lance.
776 777 778

config NET_VENDOR_SMC
	bool "Western Digital/SMC cards"
779
	depends on NET_ETHERNET && (ISA || MCA || EISA || MAC)
780 781 782
	help
	  If you have a network (Ethernet) card belonging to this class, say Y
	  and read the Ethernet-HOWTO, available from
783
	  <http://www.tldp.org/docs.html#howto>.
784 785 786 787 788 789 790 791 792 793 794 795

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about Western Digital cards. If you say Y, you will be
	  asked for your specific card in the following questions.

config WD80x3
	tristate "WD80*3 support"
	depends on NET_VENDOR_SMC && ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
796
	  <http://www.tldp.org/docs.html#howto>.
797 798 799

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
800
	  The module will be called wd.  If you want to compile it as a
801 802 803 804 805 806 807 808 809
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config ULTRAMCA
	tristate "SMC Ultra MCA support"
	depends on NET_VENDOR_SMC && MCA
	help
	  If you have a network (Ethernet) card of this type and are running
	  an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
810
	  available from <http://www.tldp.org/docs.html#howto>.
811 812 813

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
814
	  The module will be called smc-mca.  If you want to compile it as a
815 816 817 818 819 820 821 822 823
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config ULTRA
	tristate "SMC Ultra support"
	depends on NET_VENDOR_SMC && ISA
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
824
	  <http://www.tldp.org/docs.html#howto>.
825 826 827 828 829 830 831 832 833 834

	  Important: There have been many reports that, with some motherboards
	  mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
	  such as some BusLogic models) causes corruption problems with many
	  operating systems. The Linux smc-ultra driver has a work-around for
	  this but keep it in mind if you have such a SCSI card and have
	  problems.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
835
	  The module will be called smc-ultra.  If you want to compile it as
836 837 838 839 840 841 842 843 844
	  a module, say M here and read <file:Documentation/modules.txt> as
	  well as <file:Documentation/networking/net-modules.txt>.

config ULTRA32
	tristate "SMC Ultra32 EISA support"
	depends on NET_VENDOR_SMC && EISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
845
	  <http://www.tldp.org/docs.html#howto>.
846 847 848

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
849
	  The module will be called smc-ultra32.  If you want to compile it
850 851 852 853 854
	  as a module, say M here and read <file:Documentation/modules.txt> as
	  well as <file:Documentation/networking/net-modules.txt>.

config SMC9194
	tristate "SMC 9194 support"
855
	depends on NET_VENDOR_SMC && (ISA || MAC)
856 857 858 859 860 861
	---help---
	  This is support for the SMC9xxx based Ethernet cards. Choose this
	  option if you have a DELL laptop with the docking station, or
	  another SMC9192/9194 based chipset.  Say Y if you want it compiled
	  into the kernel, and read the file
	  <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
862
	  available from <http://www.tldp.org/docs.html#howto>.
863 864 865

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
866
	  The module will be called smc9194.  If you want to compile it as a
867 868 869 870 871
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config NET_VENDOR_RACAL
	bool "Racal-Interlan (Micom) NI cards"
872
	depends on NET_ETHERNET && ISA
873 874 875
	help
	  If you have a network (Ethernet) card belonging to this class, such
	  as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
876
	  available from <http://www.tldp.org/docs.html#howto>.
877 878 879 880 881 882 883 884 885 886 887 888

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about NI cards. If you say Y, you will be asked for
	  your specific card in the following questions.

config NI5010
	tristate "NI5010 support (EXPERIMENTAL)"
	depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
889
	  <http://www.tldp.org/docs.html#howto>. Note that this is still
890 891 892 893
	  experimental code.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
894
	  The module will be called ni5010.  If you want to compile it as a
895 896 897 898 899 900 901 902 903
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config NI52
	tristate "NI5210 support"
	depends on NET_VENDOR_RACAL && ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
904
	  <http://www.tldp.org/docs.html#howto>.
905 906 907

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
908
	  The module will be called ni52.  If you want to compile it as a
909 910 911 912 913 914 915 916 917
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config NI65
	tristate "NI6510 support"
	depends on NET_VENDOR_RACAL && ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
918
	  <http://www.tldp.org/docs.html#howto>.
919 920 921

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
922
	  The module will be called ni65.  If you want to compile it as a
923 924 925 926 927 928
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

source "drivers/net/tulip/Kconfig"

config AT1700
929
	tristate "AT1700/1720/RE1000Plus(C-Bus) support (EXPERIMENTAL)"
930 931 932 933
	depends on NET_ETHERNET && (ISA || MCA) && EXPERIMENTAL
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
934
	  <http://www.tldp.org/docs.html#howto>.
935 936 937 938 939 940

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  If you want to compile it as a module, say M here and read
	  <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
941
	  called at1700.
942 943 944 945 946 947 948

config DEPCA
	tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
	depends on NET_ETHERNET && (ISA || EISA || MCA)
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
949
	  <http://www.tldp.org/docs.html#howto> as well as
950 951 952 953 954 955 956
	  <file:drivers/net/depca.c>.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called
957
	  depca.
958 959 960 961 962 963 964

config HP100
	tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
	depends on NET_ETHERNET && (ISA || EISA || PCI)
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
965
	  <http://www.tldp.org/docs.html#howto>.
966 967 968 969 970

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
971
	  called hp100.
972 973 974

config NET_ISA
	bool "Other ISA cards"
975
	depends on NET_ETHERNET && ISA && !X86_PC9800
976 977 978 979 980
	---help---
	  If your network (Ethernet) card hasn't been mentioned yet and its
	  bus system (that's the way the cards talks to the other components
	  of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
	  Make sure you know the name of your card. Read the Ethernet-HOWTO,
981
	  available from <http://www.tldp.org/docs.html#howto>.
982 983 984 985 986 987 988 989 990 991 992 993 994 995

	  If unsure, say Y.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the remaining ISA network card questions. If you say Y, you will be
	  asked for your specific card in the following questions.

config E2100
	tristate "Cabletron E21xx support"
	depends on NET_ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
996
	  <http://www.tldp.org/docs.html#howto>.
997 998 999

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1000
	  The module will be called e2100.  If you want to compile it as a
1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config EWRK3
	tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
	depends on NET_ISA
	---help---
	  This driver supports the DE203, DE204 and DE205 network (Ethernet)
	  cards. If this is for you, say Y and read
	  <file:Documentation/networking/ewrk3.txt> in the kernel source as
	  well as the Ethernet-HOWTO, available from
1012
	  <http://www.tldp.org/docs.html#howto>.
1013 1014 1015 1016 1017

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
1018
	  called ewrk3.
1019 1020 1021 1022 1023 1024 1025

config EEXPRESS
	tristate "EtherExpress 16 support"
	depends on NET_ISA
	---help---
	  If you have an EtherExpress16 network (Ethernet) card, say Y and
	  read the Ethernet-HOWTO, available from
1026
	  <http://www.tldp.org/docs.html#howto>.  Note that the Intel
1027 1028 1029 1030 1031 1032 1033 1034
	  EtherExpress16 card used to be regarded as a very poor choice
	  because the driver was very unreliable. We now have a new driver
	  that should do better.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
1035
	  called eexpress.
1036 1037 1038 1039 1040 1041 1042 1043 1044

config EEXPRESS_PRO
	tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
	depends on NET_ISA
	---help---
	  If you have a network (Ethernet) card of this type, say Y. This
	  driver supports intel i82595{FX,TX} based boards. Note however
	  that the EtherExpress PRO/100 Ethernet card has its own separate
	  driver.  Please read the Ethernet-HOWTO, available from
1045
	  <http://www.tldp.org/docs.html#howto>.
1046 1047 1048

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1049
	  The module will be called eepro.  If you want to compile it as a
1050 1051 1052 1053 1054 1055 1056 1057 1058
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config FMV18X
	tristate "FMV-181/182/183/184 support (OBSOLETE)"
	depends on NET_ISA && OBSOLETE
	---help---
	  If you have a Fujitsu FMV-181/182/183/184 network (Ethernet) card,
	  say Y and read the Ethernet-HOWTO, available from
1059
	  <http://www.tldp.org/docs.html#howto>.
1060 1061 1062 1063 1064 1065

	  If you use an FMV-183 or FMV-184 and it is not working, you may need
	  to disable Plug & Play mode of the card.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1066
	  The module will be called fmv18x.  If you want to compile it as a
1067 1068 1069 1070 1071 1072 1073 1074 1075
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config HPLAN_PLUS
	tristate "HP PCLAN+ (27247B and 27252A) support"
	depends on NET_ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1076
	  <http://www.tldp.org/docs.html#howto>.
1077 1078 1079

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1080
	  The module will be called hp-plus.  If you want to compile it as a
1081 1082 1083 1084 1085 1086 1087 1088 1089
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config HPLAN
	tristate "HP PCLAN (27245 and other 27xxx series) support"
	depends on NET_ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1090
	  <http://www.tldp.org/docs.html#howto>.
1091 1092 1093

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1094
	  The module will be called hp.  If you want to compile it as a
1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config LP486E
	tristate "LP486E on board Ethernet"
	depends on NET_ISA
	help
	  Say Y here to support the 82596-based on-board Ethernet controller
	  for the Panther motherboard, which is one of the two shipped in the
	  Intel Professional Workstation.

config ETH16I
	tristate "ICL EtherTeam 16i/32 support"
	depends on NET_ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1112
	  <http://www.tldp.org/docs.html#howto>.
1113 1114 1115

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1116
	  The module will be called eth16i.  If you want to compile it as a
1117 1118 1119 1120 1121
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config NE2000
	tristate "NE2000/NE1000 support"
1122
	depends on NET_ISA || (Q40 && m)
1123 1124 1125
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1126
	  <http://www.tldp.org/docs.html#howto>.  Many Ethernet cards
1127 1128 1129 1130 1131 1132 1133 1134 1135 1136
	  without a specific driver are compatible with NE2000.

	  If you have a PCI NE2000 card however, say N here and Y to "PCI
	  NE2000 support", above. If you have a NE2000 card and are running on
	  an MCA system (a bus system used on some IBM PS/2 computers and
	  laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
	  below.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1137
	  The module will be called ne.  If you want to compile it as a
1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config ZNET
	tristate "Zenith Z-Note support (EXPERIMENTAL)"
	depends on NET_ISA && EXPERIMENTAL
	help
	  The Zenith Z-Note notebook computer has a built-in network
	  (Ethernet) card, and this is the Linux driver for it. Note that the
	  IBM Thinkpad 300 is compatible with the Z-Note and is also supported
	  by this driver. Read the Ethernet-HOWTO, available from
1149
	  <http://www.tldp.org/docs.html#howto>.
1150 1151 1152

config SEEQ8005
	tristate "SEEQ8005 support (EXPERIMENTAL)"
Alan Cox's avatar
Alan Cox committed
1153
	depends on NET_ISA && EXPERIMENTAL
1154 1155 1156
	help
	  This is a driver for the SEEQ 8005 network (Ethernet) card.  If this
	  is for you, read the Ethernet-HOWTO, available from
1157
	  <http://www.tldp.org/docs.html#howto>.
1158 1159 1160 1161 1162

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
1163
	  called ewrk3.
1164 1165 1166 1167 1168 1169 1170

config SK_G16
	tristate "SK_G16 support (OBSOLETE)"
	depends on NET_ISA && OBSOLETE
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1171
	  <http://www.tldp.org/docs.html#howto>.
1172

1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221
config NET_CBUS
	bool "NEC PC-9800 C-bus cards"
	depends on NET_ETHERNET && ISA && X86_PC9800
	---help---
	  If your network (Ethernet) card hasn't been mentioned yet and its
	  bus system (that's the way the cards talks to the other components
	  of your computer) is NEC PC-9800 C-Bus, say Y.

config NE2K_CBUS
	tristate "Most NE2000-based Ethernet support"
	depends on NET_CBUS

config NE2K_CBUS_EGY98
	bool "Melco EGY-98 support"
	depends on NE2K_CBUS

config NE2K_CBUS_LGY98
	bool "Melco LGY-98 support"
	depends on NE2K_CBUS

config NE2K_CBUS_ICM
	bool "ICM IF-27xxET support"
	depends on NE2K_CBUS

config NE2K_CBUS_IOLA98
	bool "I-O DATA LA-98 support"
	depends on NE2K_CBUS

config NE2K_CBUS_CNET98EL
	bool "Contec C-NET(98)E/L support"
	depends on NE2K_CBUS

config NE2K_CBUS_CNET98EL_IO_BASE
	hex "C-NET(98)E/L I/O base address (0xaaed or 0x55ed)"
	depends on NE2K_CBUS_CNET98EL
	default "0xaaed"

config NE2K_CBUS_ATLA98
	bool "Allied Telesis LA-98 Support"
	depends on NE2K_CBUS

config NE2K_CBUS_BDN
	bool "ELECOM Laneed LD-BDN[123]A Support"
	depends on NE2K_CBUS

config NE2K_CBUS_NEC108
	bool "NEC PC-9801-108 Support"
	depends on NE2K_CBUS

1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234
config SKMC
	tristate "SKnet MCA support"
	depends on NET_ETHERNET && MCA
	---help---
	  These are Micro Channel Ethernet adapters. You need to say Y to "MCA
	  support" in order to use this driver.  Supported cards are the SKnet
	  Junior MC2 and the SKnet MC2(+).  The driver automatically
	  distinguishes between the two cards. Note that using multiple boards
	  of different type hasn't been tested with this driver.  Say Y if you
	  have one of these Ethernet adapters.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1235
	  The module is called sk_mca.  If you want to compile it as a
1236 1237 1238 1239 1240 1241 1242 1243 1244
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config NE2_MCA
	tristate "NE/2 (ne2000 MCA version) support"
	depends on NET_ETHERNET && MCA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1245
	  <http://www.tldp.org/docs.html#howto>.
1246 1247 1248

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1249
	  The module will be called ne2.  If you want to compile it as a
1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config IBMLANA
	tristate "IBM LAN Adapter/A support"
	depends on NET_ETHERNET && MCA
	---help---
	  This is a Micro Channel Ethernet adapter.  You need to set
	  CONFIG_MCA to use this driver.  It is both available as an in-kernel
	  driver and as a module ( = code which can be inserted in and removed
	  from the running kernel whenever you want).  If you want to compile
	  it as a module, say M here and read <file:Documentation/modules.txt>
	  as well as <file:Documentation/networking/net-modules.txt>. The only
	  currently supported card is the IBM LAN Adapter/A for Ethernet.  It
	  will both support 16K and 32K memory windows, however a 32K window
	  gives a better security against packet losses.  Usage of multiple
	  boards with this driver should be possible, but has not been tested
	  up to now due to lack of hardware.

config NET_PCI
	bool "EISA, VLB, PCI and on board controllers"
	depends on NET_ETHERNET && (ISA || EISA || PCI)
	help
	  This is another class of network cards which attach directly to the
	  bus. If you have one of those, say Y and read the Ethernet-HOWTO,
1275
	  available from <http://www.tldp.org/docs.html#howto>.
1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about this class of network cards. If you say Y, you
	  will be asked for your specific card in the following questions. If
	  you are unsure, say Y.

config PCNET32
	tristate "AMD PCnet32 PCI support"
	depends on NET_PCI && PCI
	help
	  If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
	  answer Y here and read the Ethernet-HOWTO, available from
1289
	  <http://www.tldp.org/docs.html#howto>.
1290 1291 1292

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1293
	  The module will be called pcnet32.  If you want to compile it as a
1294 1295 1296
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

1297 1298 1299 1300 1301 1302
config AMD8111_ETH
	tristate "AMD 8111 (new PCI lance) support"
	depends on NET_PCI && PCI
	help
	  If you have an AMD 8111-based PCI lance ethernet card,
	  answer Y here and read the Ethernet-HOWTO, available from
1303
	  <http://www.tldp.org/docs.html#howto>.
1304 1305 1306

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1307
	  The module will be called amd8111e.  If you want to compile it as a
1308 1309 1310
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322
config ADAPTEC_STARFIRE
	tristate "Adaptec Starfire/DuraLAN support"
	depends on NET_PCI && PCI
	help
	  Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
	  adapter. The DuraLAN chip is used on the 64 bit PCI boards from
	  Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
	  driver.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
1323
	  recommended.  The module will be called starfire.
1324

1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336
config ADAPTEC_STARFIRE_NAPI
	bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
	depends on ADAPTEC_STARFIRE && EXPERIMENTAL
	help
	  NAPI is a new driver API designed to reduce CPU and interrupt load
	  when the driver is receiving lots of packets from the card. It is
	  still somewhat experimental and thus not yet enabled by default.

	  If your estimated Rx load is 10kpps or more, or if the card will be
	  deployed on potentially unfriendly networks (e.g. in a firewall),
	  then say Y here.

1337 1338 1339 1340 1341 1342
config AC3200
	tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
	depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1343
	  <http://www.tldp.org/docs.html#howto>.
1344 1345 1346

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1347
	  The module will be called ac3200.  If you want to compile it as a
1348 1349 1350 1351 1352 1353 1354 1355 1356
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config APRICOT
	tristate "Apricot Xen-II on board Ethernet"
	depends on NET_PCI && ISA
	help
	  If you have a network (Ethernet) controller of this type, say Y and
	  read the Ethernet-HOWTO, available from
1357
	  <http://www.tldp.org/docs.html#howto>.
1358 1359 1360 1361 1362

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
1363
	  called apricot.
1364

1365 1366 1367 1368 1369 1370
config B44
	tristate "Broadcom 4400 ethernet support (EXPERIMENTAL)"
	depends on NET_PCI && PCI && EXPERIMENTAL
	help
	  If you have a network (Ethernet) controller of this type, say Y and
	  read the Ethernet-HOWTO, available from
1371
	  <http://www.tldp.org/docs.html#howto>.
1372 1373 1374 1375 1376

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
1377
	  called b44.
1378

1379 1380 1381 1382 1383 1384 1385
config CS89x0
	tristate "CS89x0 support"
	depends on NET_PCI && ISA
	---help---
	  Support for CS89x0 chipset based Ethernet cards. If you have a
	  network (Ethernet) card of this type, say Y and read the
	  Ethernet-HOWTO, available from
1386
	  <http://www.tldp.org/docs.html#howto> as well as
1387 1388 1389 1390 1391 1392
	  <file:Documentation/networking/cs89x0.txt>.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
1393
	  called cs89x.
1394

1395 1396
config TC35815
	tristate "TOSHIBA TC35815 Ethernet support"
1397
	depends on NET_PCI && PCI && TOSHIBA_JMR3927
1398

1399 1400 1401 1402 1403 1404 1405 1406
config DGRS
	tristate "Digi Intl. RightSwitch SE-X support"
	depends on NET_PCI && (PCI || EISA)
	---help---
	  This is support for the Digi International RightSwitch series of
	  PCI/EISA Ethernet switch cards. These include the SE-4 and the SE-6
	  models.  If you have a network card of this type, say Y and read the
	  Ethernet-HOWTO, available from
1407
	  <http://www.tldp.org/docs.html#howto>.  More specific
1408 1409 1410 1411
	  information is contained in <file:Documentation/networking/dgrs.txt>.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1412
	  The module will be called dgrs.  If you want to compile it as a
1413 1414 1415 1416 1417 1418 1419 1420 1421
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config EEPRO100
	tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
	depends on NET_PCI && PCI
	help
	  If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
	  card, say Y and read the Ethernet-HOWTO, available from
1422
	  <http://www.tldp.org/docs.html#howto>.
1423 1424 1425

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1426
	  The module will be called eepro100.  If you want to compile it as
1427 1428 1429
	  a module, say M here and read <file:Documentation/modules.txt> as
	  well as <file:Documentation/networking/net-modules.txt>.

1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440

config EEPRO100_PIO
	bool "Use PIO instead of MMIO" if !X86_VISWS
	depends on EEPRO100
	default y if X86_VISWS
	help
	  This instructs the driver to use programmed I/O ports (PIO) instead
	  of PCI shared memory (MMIO).  This can possibly solve some problems
	  in case your mainboard has memory consistency issues.  If unsure,
	  say N.

1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513
config E100
	tristate "EtherExpressPro/100 support (e100, Alternate Intel driver)"
	depends on NET_PCI && PCI
	---help---
	  This driver supports Intel(R) PRO/100 family of adapters, which 
	  includes:

	  Controller  Adapter Name                       Board IDs
	  ----------  ------------                       ---------

	  82558       PRO/100+ PCI Adapter               668081-xxx, 
	  689661-xxx
	  82558       PRO/100+ Management Adapter        691334-xxx, 
	  701738-xxx,
	  721383-xxx
	  82558       PRO/100+ Dual Port Server Adapter  714303-xxx, 
	  711269-xxx, 
	  A28276-xxx
	  82558       PRO/100+ PCI Server Adapter        710550-xxx
	  82550       PRO/100 S Server Adapter           752438-xxx
	  82559                                          A56831-xxx, 
	  A10563-xxx,
	  A12171-xxx, 
	  A12321-xxx, 
	  A12320-xxx, 
	  A12170-xxx
	  748568-xxx
	  748565-xxx
	  82550       PRO/100 S Desktop Adapter          751767-xxx
	  82559                                          748592-xxx, 
	  A12167-xxx, 
	  A12318-xxx, 
	  A12317-xxx, 
	  A12165-xxx,
	  748569-xxx 
	  82559       PRO/100+ Server Adapter            729757-xxx
	  82559       PRO/100 S Management Adapter       748566-xxx, 
	  748564-xxx
	  82550       PRO/100 S Dual Port Server Adapter A56831-xxx
	  82551       PRO/100 M Desktop Adapter          A80897-xxx
	  PRO/100 S Advanced Management Adapter 
	  747842-xxx, 
	  745171-xxx
	  CNR         PRO/100 VE Desktop Adapter         A10386-xxx, 
	  A10725-xxx, 
	  A23801-xxx, 
	  A19716-xxx
	  PRO/100 VM Desktop Adapter         A14323-xxx, 
	  A19725-xxx, 
	  A23801-xxx, 
	  A22220-xxx, 
	  A23796-xxx


	  To verify that your adapter is supported, find the board ID number 
	  on the adapter. Look for a label that has a barcode and a number 
	  in the format 123456-001 (six digits hyphen three digits). Match 
	  this to the list of numbers above.

	  For more information on how to identify your adapter, go to the 
	  Adapter & Driver ID Guide at:

	  http://support.intel.com/support/network/adapter/pro100/21397.htm

	  For the latest Intel PRO/100 network driver for Linux, see:

	  http://appsr.intel.com/scripts-df/support_intel.asp

	  More specific information on configuring the driver is in 
	  <file:Documentation/networking/e100.txt>.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1514
	  The module will be called e100.  If you want to compile it as a
1515 1516 1517 1518 1519 1520 1521 1522 1523
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config LNE390
	tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
	depends on NET_PCI && EISA && EXPERIMENTAL
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1524
	  <http://www.tldp.org/docs.html#howto>.
1525 1526 1527

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1528
	  The module will be called lne390.  If you want to compile it as a
1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config FEALNX
	tristate "Myson MTD-8xx PCI Ethernet support"
	depends on NET_PCI && PCI
	help
	  Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
	  cards. Specifications and data at
	  <http://www.myson.com.hk/mtd/datasheet/>.

config NATSEMI
	tristate "National Semiconductor DP8381x series PCI Ethernet support"
	depends on NET_PCI && PCI
	help
	  This driver is for the National Semiconductor DP83810 series,
	  which is used in cards from PureData, NetGear, Linksys
	  and others, including the 83815 chip.
	  More specific information and updates are available from
	  <http://www.scyld.com/network/natsemi.html>.

config NE2K_PCI
	tristate "PCI NE2000 and clones support (see help)"
	depends on NET_PCI && PCI
	---help---
	  This driver is for NE2000 compatible PCI cards. It will not work
	  with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
	  support" below). If you have a PCI NE2000 network (Ethernet) card,
	  say Y and read the Ethernet-HOWTO, available from
1558
	  <http://www.tldp.org/docs.html#howto>.
1559 1560 1561 1562 1563 1564 1565 1566

	  This driver also works for the following NE2000 clone cards:
	  RealTek RTL-8029  Winbond 89C940  Compex RL2000  KTI ET32P2
	  NetVin NV5000SC   Via 86C926      SureCom NE34   Winbond
	  Holtek HT80232    Holtek HT80229

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1567
	  The module will be called ne2k-pci.  If you want to compile it as
1568 1569 1570 1571 1572 1573 1574 1575 1576
	  a module, say M here and read <file:Documentation/modules.txt> as
	  well as <file:Documentation/networking/net-modules.txt>.

config NE3210
	tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
	depends on NET_PCI && EISA && EXPERIMENTAL
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1577
	  <http://www.tldp.org/docs.html#howto>.  Note that this driver
1578 1579 1580 1581
	  will NOT WORK for NE3200 cards as they are completely different.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1582
	  The module will be called ne3210.  If you want to compile it as a
1583 1584 1585 1586 1587 1588 1589 1590 1591
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config ES3210
	tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
	depends on NET_PCI && EISA && EXPERIMENTAL
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
1592
	  <http://www.tldp.org/docs.html#howto>.
1593 1594 1595

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1596
	  The module will be called es3210.  If you want to compile it as a
1597 1598 1599 1600 1601 1602 1603 1604 1605 1606
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config 8139CP
	tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
	depends on NET_PCI && PCI && EXPERIMENTAL
	help
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the RTL8139C+ chips. If you have one of those, say Y and read
	  the Ethernet-HOWTO, available from
1607
	  <http://www.tldp.org/docs.html#howto>.
1608 1609 1610 1611

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read Documentation/modules.txt. This is recommended.
1612
	  The module will be called 8139cp.
1613 1614 1615 1616 1617 1618 1619 1620 1621

config 8139TOO
	tristate "RealTek RTL-8139 PCI Fast Ethernet Adapter support"
	depends on NET_PCI && PCI
	---help---
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the RTL8139 chips. If you have one of those, say Y and read
	  <file:Documentation/networking/8139too.txt> as well as the
	  Ethernet-HOWTO, available from
1622
	  <http://www.tldp.org/docs.html#howto>.
1623 1624 1625 1626

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
1627
	  recommended.  The module will be called 8139too.
1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675

config 8139TOO_PIO
	bool "Use PIO instead of MMIO"
	depends on 8139TOO
	help
	  This instructs the driver to use programmed I/O ports (PIO) instead
	  of PCI shared memory (MMIO).  This can possibly solve some problems
	  in case your mainboard has memory consistency issues.  If unsure,
	  say N.

config 8139TOO_TUNE_TWISTER
	bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
	depends on 8139TOO
	help
	  This implements a function which might come in handy in case you
	  are using low quality on long cabling. It is required for RealTek
	  RTL-8139 revision K boards, and totally unused otherwise.  It tries
	  to match the transceiver to the cable characteristics. This is
	  experimental since hardly documented by the manufacturer.
	  If unsure, say Y.

config 8139TOO_8129
	bool "Support for older RTL-8129/8130 boards"
	depends on 8139TOO
	help
	  This enables support for the older and uncommon RTL-8129 and
	  RTL-8130 chips, which support MII via an external transceiver,
	  instead of an internal one.  Disabling this option will save some
	  memory by making the code size smaller.  If unsure, say Y.

config 8139_OLD_RX_RESET
	bool "Use older RX-reset method"
	depends on 8139TOO
	help
	  The 8139too driver was recently updated to contain a more rapid
	  reset sequence, in the face of severe receive errors.  This "new"
	  RX-reset method should be adequate for all boards.  But if you
	  experience problems, you can enable this option to restore the
	  old RX-reset behavior.  If unsure, say N.

config SIS900
	tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
	depends on NET_PCI && PCI
	---help---
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
	  SiS 630 and SiS 540 chipsets.  If you have one of those, say Y and
	  read the Ethernet-HOWTO, available at
1676
	  <http://www.tldp.org/docs.html#howto>.  Please read
1677 1678 1679 1680 1681 1682 1683 1684 1685
	  <file:Documentation/networking/sis900.txt> and comments at the
	  beginning of <file:drivers/net/sis900.c> for more information.

	  This driver also supports AMD 79C901 HomePNA so that you can use
	  your phone line as a network cable.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
1686
	  recommended.  The module will be called sis900.
1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721

config EPIC100
	tristate "SMC EtherPower II"
	depends on NET_PCI && PCI
	help
	  This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
	  which is based on the SMC83c17x (EPIC/100).
	  More specific information and updates are available from
	  <http://www.scyld.com/network/epic100.html>.

config SUNDANCE
	tristate "Sundance Alta support"
	depends on NET_PCI && PCI
	help
	  This driver is for the Sundance "Alta" chip.
	  More specific information and updates are available from
	  <http://www.scyld.com/network/sundance.html>.

config SUNDANCE_MMIO
	bool "Use MMIO instead of PIO"
	depends on SUNDANCE
	help
	  Enable memory-mapped I/O for interaction with Sundance NIC registers.
	  Do NOT enable this by default, PIO (enabled when MMIO is disabled)
	  is known to solve bugs on certain chips.

	  If unsure, say N.

config TLAN
	tristate "TI ThunderLAN support"
	depends on NET_PCI && (PCI || EISA)
	---help---
	  If you have a PCI Ethernet network card based on the ThunderLAN chip
	  which is supported by this driver, say Y and read the
	  Ethernet-HOWTO, available from
1722
	  <http://www.tldp.org/docs.html#howto>.
1723 1724 1725 1726 1727 1728 1729

	  Devices currently supported by this driver are Compaq Netelligent,
	  Compaq NetFlex and Olicom cards.  Please read the file
	  <file:Documentation/networking/tlan.txt> for more details.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1730
	  The module will be called tlan.  If you want to compile it as a
1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

	  Please email feedback to  torben.mathiasen@compaq.com.

config VIA_RHINE
	tristate "VIA Rhine support"
	depends on NET_PCI && PCI
	help
	  If you have a VIA "rhine" based network card (Rhine-I (3043) or
	  Rhine-2 (VT86c100A)), say Y here.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1745
	  The module will be called via-rhine.  If you want to compile it as
1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772
	  a module, say M here and read <file:Documentation/modules.txt> as
	  well as <file:Documentation/networking/net-modules.txt>.

config VIA_RHINE_MMIO
	bool "Use MMIO instead of PIO (EXPERIMENTAL)"
	depends on VIA_RHINE && EXPERIMENTAL
	help
	  This instructs the driver to use PCI shared memory (MMIO) instead of
	  programmed I/O ports (PIO). Enabling this gives an improvement in
	  processing time in parts of the driver.

	  It is not known if this works reliably on all "rhine" based cards,
	  but it has been tested successfully on some DFE-530TX adapters.

	  If unsure, say N.

config LAN_SAA9730
	bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)"
	depends on NET_PCI && EXPERIMENTAL && MIPS
	help
	  The SAA9730 is a combined multimedia and peripheral controller used
	  in thin clients, Internet access terminals, and diskless
	  workstations.
	  See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.

config NET_POCKET
	bool "Pocket and portable adapters"
1773
	depends on NET_ETHERNET && ISA
1774 1775 1776 1777
	---help---
	  Cute little network (Ethernet) devices which attach to the parallel
	  port ("pocket adapters"), commonly used with laptops. If you have
	  one of those, say Y and read the Ethernet-HOWTO, available from
1778
	  <http://www.tldp.org/docs.html#howto>.
1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799

	  If you want to plug a network (or some other) card into the PCMCIA
	  (or PC-card) slot of your laptop instead (PCMCIA is the standard for
	  credit card size extension cards used by all modern laptops), you
	  need the pcmcia-cs package (location contained in the file
	  <file:Documentation/Changes>) and you can say N here.

	  Laptop users should read the Linux Laptop home page at
	  <http://www.cs.utexas.edu/users/kharker/linux-laptop/>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about this class of network devices. If you say Y, you
	  will be asked for your specific device in the following questions.

config ATP
	tristate "AT-LAN-TEC/RealTek pocket adapter support"
	depends on NET_POCKET && ISA && X86
	---help---
	  This is a network (Ethernet) device which attaches to your parallel
	  port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
1800
	  available from <http://www.tldp.org/docs.html#howto>, if you
1801 1802 1803 1804 1805 1806 1807
	  want to use this.  If you intend to use this driver, you should have
	  said N to the "Parallel printer support", because the two drivers
	  don't like each other.

	  If you want to compile this driver as a module however ( = code
	  which can be inserted in and removed from the running kernel
	  whenever you want), say M here and read
1808
	  <file:Documentation/modules.txt>.  The module will be called atp.
1809 1810 1811 1812 1813 1814 1815 1816

config DE600
	tristate "D-Link DE600 pocket adapter support"
	depends on NET_POCKET && ISA
	---help---
	  This is a network (Ethernet) device which attaches to your parallel
	  port. Read <file:Documentation/networking/DLINK.txt> as well as the
	  Ethernet-HOWTO, available from
1817
	  <http://www.tldp.org/docs.html#howto>, if you want to use
1818 1819 1820 1821 1822 1823 1824 1825
	  this. It is possible to have several devices share a single parallel
	  port and it is safe to compile the corresponding drivers into the
	  kernel.

	  If you want to compile this driver as a module however ( = code
	  which can be inserted in and removed from the running kernel
	  whenever you want), say M here and read
	  <file:Documentation/modules.txt>.
1826
	  The module will be called de600.
1827 1828 1829 1830 1831 1832 1833 1834

config DE620
	tristate "D-Link DE620 pocket adapter support"
	depends on NET_POCKET && ISA
	---help---
	  This is a network (Ethernet) device which attaches to your parallel
	  port. Read <file:Documentation/networking/DLINK.txt> as well as the
	  Ethernet-HOWTO, available from
1835
	  <http://www.tldp.org/docs.html#howto>, if you want to use
1836 1837 1838 1839 1840 1841 1842 1843
	  this. It is possible to have several devices share a single parallel
	  port and it is safe to compile the corresponding drivers into the
	  kernel.

	  If you want to compile this driver as a module however ( = code
	  which can be inserted in and removed from the running kernel
	  whenever you want), say M here and read
	  <file:Documentation/modules.txt>.
1844
	  The module will be called de620.
1845 1846

config SGISEEQ
Ralf Bächle's avatar
Ralf Bächle committed
1847
	tristate "SGI Seeq ethernet controller support"
1848 1849 1850 1851 1852 1853
	depends on NET_ETHERNET && SGI_IP22
	help
	  Say Y here if you have an Seeq based Ethernet network card. This is
	  used in many Silicon Graphics machines.

config DECLANCE
Ralf Bächle's avatar
Ralf Bächle committed
1854
	tristate "DEC LANCE ethernet controller support"
1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868
	depends on NET_ETHERNET && DECSTATION
	help
	  This driver is for the series of Ethernet controllers produced by
	  DEC (now Compaq) based on the AMD Lance chipset, including the
	  DEPCA series.  (This chipset is better known via the NE2100 cards.)

config BAGETLANCE
	tristate "Baget AMD LANCE support"
	depends on NET_ETHERNET && BAGET_MIPS
	help
	  Say Y to enable kernel support for AMD Lance Ethernet cards on the
	  MIPS-32-based Baget embedded system.  This chipset is better known
	  via the NE2100 cards.

1869 1870 1871 1872 1873 1874 1875 1876 1877
config 68360_ENET
	bool "Motorola 68360 ethernet controller"
	depends on M68360
	help
	  Say Y here if you want to use the built-in ethernet controller of
	  the Motorola 68360 processor.

config FEC
	bool "FEC ethernet controller (of ColdFire 5272)"
1878
	depends on M5272 || M5282
1879 1880 1881 1882
	help
	  Say Y here if you want to use the built-in 10/100 Fast ethernet
	  controller on the Motorola ColdFire 5272 processor.

1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905
endmenu

#
#	Gigabit Ethernet
#

menu "Ethernet (1000 Mbit)"
	depends on NETDEVICES

config ACENIC
	tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
	depends on PCI
	---help---
	  Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
	  GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
	  adapter. The driver allows for using the Jumbo Frame option (9000
	  bytes/frame) however it requires that your switches can handle this
	  as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
	  line.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
1906
	  recommended.  The module will be called acenic.
1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932

config ACENIC_OMIT_TIGON_I
	bool "Omit support for old Tigon I based AceNICs"
	depends on ACENIC
	help
	  Say Y here if you only have Tigon II based AceNICs and want to leave
	  out support for the older Tigon I based cards which are no longer
	  being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
	  version)).  This will reduce the size of the driver object by
	  app. 100KB.  If you are not sure whether your card is a Tigon I or a
	  Tigon II, say N here.

	  The safe and default value for this is N.

config DL2K
	tristate "D-Link DL2000-based Gigabit Ethernet support"
	depends on PCI
	help
	  This driver supports D-Link 2000-based gigabit ethernet cards, which
	  includes
	  D-Link DGE-550T Gigabit Ethernet Adapter.
	  D-Link DL2000-based Gigabit Ethernet Adapter.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
1933
	  recommended.  The module will be called dl2k.
1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953

config E1000
	tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
	depends on PCI
	---help---
	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
	  adapters, which includes:

	  Controller  Adapter Name                         Board IDs
	  ----------  ------------                         ---------
	  82542       PRO/1000 Gigabit Server Adapter      700262-xxx,
	  717037-xxx
	  82543       PRO/1000 F Server Adapter            738640-xxx,
	  A38888-xxx
	  82543       PRO/1000 T Server Adapter            A19845-xxx,
	  A33948-xxx
	  82544       PRO/1000 XT Server Adapter           A51580-xxx
	  82544       PRO/1000 XF Server Adapter           A50484-xxx
	  82544       PRO/1000 T Desktop Adapter           A62947-xxx
	  82540       PRO/1000 MT Desktop Adapter          A78408-xxx
1954
	  82541       PRO/1000 MT Desktop Adapter          C91016-xxx
1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975
	  82545       PRO/1000 MT Server Adapter           A92165-xxx
	  82546       PRO/1000 MT Dual Port Server Adapter A92111-xxx
	  82545       PRO/1000 MF Server Adapter           A91622-xxx
	  82545       PRO/1000 MF Server Adapter(LX)       A91624-xxx
	  82546       PRO/1000 MF Dual Port Server Adapter A91620-xxx 

	  For more information on how to identify your adapter, go to the
	  Adapter & Driver ID Guide at:

	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>

	  For general information and support, go to the Intel support
	  website at:

	  <http://support.intel.com>

	  More specific information on configuring the driver is in 
	  <file:Documentation/networking/e1000.txt>.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
1976
	  The module will be called e1000.  If you want to compile it as a
1977 1978 1979 1980
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config E1000_NAPI
1981 1982
	bool "Use Rx Polling (NAPI)"
	depends on E1000
1983 1984 1985 1986 1987 1988 1989 1990 1991 1992

config MYRI_SBUS
	tristate "MyriCOM Gigabit Ethernet support"
	depends on SBUS
	help
	  This driver supports MyriCOM Sbus gigabit Ethernet cards.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
1993
	  recommended.  The module will be called myri_sbus.
1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

config NS83820
	tristate "National Semiconduct DP83820 support"
	depends on PCI
	help
	  This is a driver for the National Semiconductor DP83820 series
	  of gigabit ethernet MACs.  Cards using this chipset include
	  the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
	  SOHO-GA2000T, SOHO-GA2500T.  The driver supports the use of
	  zero copy.

config HAMACHI
	tristate "Packet Engines Hamachi GNIC-II support"
	depends on PCI
	help
	  If you have a Gigabit Ethernet card of this type, say Y and read
	  the Ethernet-HOWTO, available from
2011
	  <http://www.tldp.org/docs.html#howto>.
2012 2013 2014 2015 2016

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
2017
	  called hamachi.
2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031

config YELLOWFIN
	tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
	depends on PCI && EXPERIMENTAL
	---help---
	  Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
	  adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
	  used by the Beowulf Linux cluster project.  See
	  <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
	  information about this driver in particular and Beowulf in general.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
2032
	  recommended.  The module will be called yellowfin.
2033

2034 2035 2036 2037 2038 2039 2040 2041 2042
config R8169
	tristate "Realtek 8169 gigabit ethernet support"
	depends on PCI
	---help---
	  Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
2043
	  recommended.  The module will be called r8169.
2044

2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055
config SIS190
	tristate "SiS190 gigabit ethernet support (EXPERIMENTAL)"
	depends on PCI && EXPERIMENTAL
	---help---
	  Say Y here if you have a SiS 190 PCI Gigabit Ethernet adapter.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
	  recommended.  The module will be called sis190.

2056
config SK98LIN
Alan Cox's avatar
Alan Cox committed
2057
	tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
2058 2059
	depends on PCI
	---help---
Alan Cox's avatar
Alan Cox committed
2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111
	  Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
	  compliant Gigabit Ethernet Adapter. The following adapters are supported
	  by this driver:
	    - 3Com 3C940 Gigabit LOM Ethernet Adapter
	    - 3Com 3C941 Gigabit LOM Ethernet Adapter
	    - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
	    - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
	    - DGE-530T Gigabit Ethernet Adapter
	    - EG1032 v2 Instant Gigabit Network Adapter
	    - EG1064 v2 Instant Gigabit Network Adapter
	    - Marvell RDK-8001 Adapter
	    - Marvell RDK-8002 Adapter
	    - Marvell RDK-8003 Adapter
	    - Marvell RDK-8004 Adapter
	    - Marvell RDK-8006 Adapter
	    - Marvell RDK-8007 Adapter
	    - Marvell RDK-8008 Adapter
	    - Marvell RDK-8009 Adapter
	    - Marvell RDK-8011 Adapter
	    - Marvell RDK-8012 Adapter
	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
	    - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
	    - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
	    - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
	    - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
	    - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
	    - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
	    - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
	    - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
	    - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
	    - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
	    - SK-9521 V2.0 10/100/1000Base-T Adapter
	    - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
	    - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
	    - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
	    - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
	    - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
	    - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
	    - SK-9521 10/100/1000Base-T Adapter
	  
	  The adapters support Jumbo Frames.
	  The dual link adapters support link-failover and dual port features.
	  Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support 
	  the scatter-gather functionality with sendfile(). Please refer to 
	  Documentation/networking/sk98lin.txt for more information about
2112 2113
	  optional driver parameters.
	  Questions concerning this driver may be addressed to:
Alan Cox's avatar
Alan Cox committed
2114 2115
	      linux@syskonnect.de
	  
2116 2117
	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
Alan Cox's avatar
Alan Cox committed
2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254
	  say M here and read Documentation/modules.txt. This is recommended.
	  The module will be called sk98lin.o.
	  
config CONFIG_SK98LIN_T1
	bool "3Com 3C940/3C941 Gigabit Ethernet Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - 3Com 3C940 Gigabit LOM Ethernet Adapter
	    - 3Com 3C941 Gigabit LOM Ethernet Adapter
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T2
	bool "Allied Telesyn AT-29xx Gigabit Ethernet Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
	    - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T3
	bool "CNet N-Way Gigabit Ethernet Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T4
	bool "D-Link DGE-530T Gigabit Ethernet Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - DGE-530T Gigabit Ethernet Adapter
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T5
	bool "Linksys EG10xx Ethernet Server Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - EG1032 v2 Instant Gigabit Network Adapter
	    - EG1064 v2 Instant Gigabit Network Adapter
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T6
	bool "Marvell RDK-80xx Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - Marvell RDK-8001 Adapter
	    - Marvell RDK-8002 Adapter
	    - Marvell RDK-8003 Adapter
	    - Marvell RDK-8004 Adapter
	    - Marvell RDK-8006 Adapter
	    - Marvell RDK-8007 Adapter
	    - Marvell RDK-8008 Adapter
	    - Marvell RDK-8009 Adapter
	    - Marvell RDK-8011 Adapter
	    - Marvell RDK-8012 Adapter
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T7
	bool "Marvell Yukon Gigabit Ethernet Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T8
	bool "SysKonnect SK-98xx Server Gigabit Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
	    - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
	    - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
	    - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
	    - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
	    - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
	    - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
	    - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
	    - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
	    - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
	
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	
config CONFIG_SK98LIN_T9
	bool "SysKonnect SK-98xx V2.0 Gigabit Ethernet Adapter"
	depends on SK98LIN
	help
	  This driver supports:
	  
	    - SK-9521 V2.0 10/100/1000Base-T Adapter
	    - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
	    - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
	    - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
	    - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
	    - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
	    - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
	    - SK-9521 10/100/1000Base-T Adapter
	  
	  Questions concerning this driver may be addressed to:
	      linux@syskonnect.de
	  

2255 2256 2257 2258 2259 2260 2261 2262 2263 2264

config TIGON3
	tristate "Broadcom Tigon3 support"
	depends on PCI
	help
	  This driver supports Broadcom Tigon3 based gigabit Ethernet cards.

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
2265
	  recommended.  The module will be called tg3.
2266 2267 2268

endmenu

2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312
#
#	10 Gigabit Ethernet
#

menu "Ethernet (10000 Mbit)"
	depends on NETDEVICES

config IXGB
	tristate "Intel(R) PRO/10GbE support"
	depends on PCI
	---help---
	  This driver supports Intel(R) PRO/10GbE family of
	  adapters, which includes:

	  Controller  Adapter Name                           Board IDs
	  ----------  ------------                           ---------
	  82597EX     Intel(R) PRO/10GbE LR Server Adapter   A82505-xxx

	  For more information on how to identify your adapter, go to the
	  Adapter & Driver ID Guide at:

	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>

	  For general information and support, go to the Intel support
	  website at:

	  <http://support.intel.com>

	  More specific information on configuring the driver is in 
	  <file:Documentation/networking/ixgb.txt>.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called ixgb.  If you want to compile it as a
	  module, say M here and read <file:Documentation/modules.txt> as well
	  as <file:Documentation/networking/net-modules.txt>.

config IXGB_NAPI
	bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
	depends on IXGB && EXPERIMENTAL

endmenu


2313 2314 2315 2316 2317 2318
config VETH
	tristate "iSeries Virtual Ethernet driver support"
	depends on NETDEVICES && PPC_ISERIES

config FDDI
	bool "FDDI driver support"
2319
	depends on NETDEVICES && (PCI || EISA)
2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365
	help
	  Fiber Distributed Data Interface is a high speed local area network
	  design; essentially a replacement for high speed Ethernet. FDDI can
	  run over copper or fiber. If you are connected to such a network and
	  want a driver for the FDDI card in your computer, say Y here (and
	  then also Y to the driver for your FDDI card, below). Most people
	  will say N.

config DEFXX
	tristate "Digital DEFEA and DEFPA adapter support"
	depends on FDDI && (PCI || EISA)
	help
	  This is support for the DIGITAL series of EISA (DEFEA) and PCI
	  (DEFPA) controllers which can connect you to a local FDDI network.

config SKFP
	tristate "SysKonnect FDDI PCI support"
	depends on FDDI && PCI
	---help---
	  Say Y here if you have a SysKonnect FDDI PCI adapter.
	  The following adapters are supported by this driver:
	  - SK-5521 (SK-NET FDDI-UP)
	  - SK-5522 (SK-NET FDDI-UP DAS)
	  - SK-5541 (SK-NET FDDI-FP)
	  - SK-5543 (SK-NET FDDI-LP)
	  - SK-5544 (SK-NET FDDI-LP DAS)
	  - SK-5821 (SK-NET FDDI-UP64)
	  - SK-5822 (SK-NET FDDI-UP64 DAS)
	  - SK-5841 (SK-NET FDDI-FP64)
	  - SK-5843 (SK-NET FDDI-LP64)
	  - SK-5844 (SK-NET FDDI-LP64 DAS)
	  - Netelligent 100 FDDI DAS Fibre SC
	  - Netelligent 100 FDDI SAS Fibre SC
	  - Netelligent 100 FDDI DAS UTP
	  - Netelligent 100 FDDI SAS UTP
	  - Netelligent 100 FDDI SAS Fibre MIC

	  Read <file:Documentation/networking/skfp.txt> for information about
	  the driver.

	  Questions concerning this driver can be addressed to:
	  linux@syskonnect.de

	  If you want to compile this driver as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt>.  This is
2366
	  recommended.  The module will be called skfp.
2367 2368 2369

config HIPPI
	bool "HIPPI driver support (EXPERIMENTAL)"
2370
	depends on NETDEVICES && EXPERIMENTAL && INET && PCI
2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388
	help
	  HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
	  1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
	  can run over copper (25m) or fiber (300m on multi-mode or 10km on
	  single-mode). HIPPI networks are commonly used for clusters and to
	  connect to super computers. If you are connected to a HIPPI network
	  and have a HIPPI network card in your computer that you want to use
	  under Linux, say Y here (you must also remember to enable the driver
	  for your HIPPI card below). Most people will say N here.

config ROADRUNNER
	tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
	depends on HIPPI && PCI
	help
	  Say Y here if this is your PCI HIPPI network card.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
2389
	  The module will be called rrunner. If you want to compile it as a
2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428
	  module, say M here and read <file:Documentation/modules.txt>.  If
	  unsure, say N.

config ROADRUNNER_LARGE_RINGS
	bool "Use large TX/RX rings (EXPERIMENTAL)"
	depends on ROADRUNNER
	help
	  If you say Y here, the RoadRunner driver will preallocate up to 2 MB
	  of additional memory to allow for fastest operation, both for
	  transmitting and receiving. This memory cannot be used by any other
	  kernel code or by user space programs. Say Y here only if you have
	  the memory.

config PLIP
	tristate "PLIP (parallel port) support"
	depends on NETDEVICES && PARPORT
	---help---
	  PLIP (Parallel Line Internet Protocol) is used to create a
	  reasonably fast mini network consisting of two (or, rarely, more)
	  local machines.  A PLIP link from a Linux box is a popular means to
	  install a Linux distribution on a machine which doesn't have a
	  CD-ROM drive (a minimal system has to be transferred with floppies
	  first). The kernels on both machines need to have this PLIP option
	  enabled for this to work.

	  The PLIP driver has two modes, mode 0 and mode 1.  The parallel
	  ports (the connectors at the computers with 25 holes) are connected
	  with "null printer" or "Turbo Laplink" cables which can transmit 4
	  bits at a time (mode 0) or with special PLIP cables, to be used on
	  bidirectional parallel ports only, which can transmit 8 bits at a
	  time (mode 1); you can find the wiring of these cables in
	  <file:Documentation/networking/PLIP.txt>.  The cables can be up to
	  15m long.  Mode 0 works also if one of the machines runs DOS/Windows
	  and has some PLIP software installed, e.g. the Crynwr PLIP packet
	  driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
	  and winsock or NCSA's telnet.

	  If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
	  as the NET-3-HOWTO, both available from
2429
	  <http://www.tldp.org/docs.html#howto>.  Note that the PLIP
2430 2431 2432 2433 2434 2435 2436 2437
	  protocol has been changed and this PLIP driver won't work together
	  with the PLIP support in Linux versions 1.0.x.  This option enlarges
	  your kernel by about 8 KB.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.  The module will be
2438
	  called plip.  If unsure, say Y or M, in case you buy a laptop
2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452
	  later.

config PPP
	tristate "PPP (point-to-point protocol) support"
	depends on NETDEVICES
	---help---
	  PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
	  the same purpose: sending Internet traffic over telephone (and other
	  serial) lines.  Ask your access provider if they support it, because
	  otherwise you can't use it; most Internet access providers these
	  days support PPP rather than SLIP.

	  To use PPP, you need an additional program called pppd as described
	  in the PPP-HOWTO, available at
2453
	  <http://www.tldp.org/docs.html#howto>.  Make sure that you have
2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469
	  the version of pppd recommended in <file:Documentation/Changes>.
	  The PPP option enlarges your kernel by about 16 KB.

	  There are actually two versions of PPP: the traditional PPP for
	  asynchronous lines, such as regular analog phone lines, and
	  synchronous PPP which can be used over digital ISDN lines for
	  example.  If you want to use PPP over phone lines or other
	  asynchronous serial lines, you need to say Y (or M) here and also to
	  the next option, "PPP support for async serial ports".  For PPP over
	  synchronous lines, you should say Y (or M) here and to "Support
	  synchronous PPP", below.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  If you said Y to "Version information on all symbols" above, then
	  you cannot compile the PPP driver into the kernel; you can then only
2470
	  compile it as a module.  The module will be called ppp_generic.
2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489
	  If you want to compile it as a module, say M here and read
	  <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>.

config PPP_MULTILINK
	bool "PPP multilink support (EXPERIMENTAL)"
	depends on PPP && EXPERIMENTAL
	help
	  PPP multilink is a protocol (defined in RFC 1990) which allows you
	  to combine several (logical or physical) lines into one logical PPP
	  connection, so that you can utilize your full bandwidth.

	  This has to be supported at the other end as well and you need a
	  version of the pppd daemon which understands the multilink protocol.

	  If unsure, say N.

config PPP_FILTER
	bool "PPP filtering"
David S. Miller's avatar
David S. Miller committed
2490
	depends on PPP
2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560
	help
	  Say Y here if you want to be able to filter the packets passing over
	  PPP interfaces.  This allows you to control which packets count as
	  activity (i.e. which packets will reset the idle timer or bring up
	  a demand-dialled link) and which packets are to be dropped entirely.
	  You need to say Y here if you wish to use the pass-filter and
	  active-filter options to pppd.

	  If unsure, say N.

config PPP_ASYNC
	tristate "PPP support for async serial ports"
	depends on PPP
	---help---
	  Say Y (or M) here if you want to be able to use PPP over standard
	  asynchronous serial ports, such as COM1 or COM2 on a PC.  If you use
	  a modem (not a synchronous or ISDN modem) to contact your ISP, you
	  need this option.

	  This code is also available as a module (code which can be inserted
	  into and removed from the running kernel).  If you want to compile
	  it as a module, say M here and read <file:Documentation/modules.txt>.

	  If unsure, say Y.

config PPP_SYNC_TTY
	tristate "PPP support for sync tty ports"
	depends on PPP
	help
	  Say Y (or M) here if you want to be able to use PPP over synchronous
	  (HDLC) tty devices, such as the SyncLink adapter. These devices
	  are often used for high-speed leased lines like T1/E1.

	  This code is also available as a module (code which can be inserted
	  into and removed from the running kernel).  If you want to compile
	  it as a module, say M here and read
	  <file:Documentation/modules.txt>.

config PPP_DEFLATE
	tristate "PPP Deflate compression"
	depends on PPP
	---help---
	  Support for the Deflate compression method for PPP, which uses the
	  Deflate algorithm (the same algorithm that gzip uses) to compress
	  each PPP packet before it is sent over the wire.  The machine at the
	  other end of the PPP link (usually your ISP) has to support the
	  Deflate compression method as well for this to be useful.  Even if
	  they don't support it, it is safe to say Y here.

	  This code is also available as a module (code which can be inserted
	  into and removed from the running kernel).  If you want to compile
	  it as a module, say M here and read
	  <file:Documentation/modules.txt>.

config PPP_BSDCOMP
	tristate "PPP BSD-Compress compression"
	depends on PPP
	---help---
	  Support for the BSD-Compress compression method for PPP, which uses
	  the LZW compression method to compress each PPP packet before it is
	  sent over the wire. The machine at the other end of the PPP link
	  (usually your ISP) has to support the BSD-Compress compression
	  method as well for this to be useful. Even if they don't support it,
	  it is safe to say Y here.

	  The PPP Deflate compression method ("PPP Deflate compression",
	  above) is preferable to BSD-Compress, because it compresses better
	  and is patent-free.

	  Note that the BSD compression code will always be compiled as a
2561
	  module; it is called bsd_comp and will show up in the directory
2562 2563 2564 2565 2566 2567 2568 2569
	  modules once you have said "make modules". If unsure, say N.

config PPPOE
	tristate "PPP over Ethernet (EXPERIMENTAL)"
	depends on EXPERIMENTAL && PPP
	help
	  Support for PPP over Ethernet.

2570 2571 2572 2573 2574
	  This driver requires the latest version of pppd from the CVS
	  repository at cvs.samba.org.  Alternatively, see the 
	  RoaringPenguin package (http://www.roaringpenguin.com/pppoe)
	  which contains instruction on how to use this driver (under 
	  the heading "Kernel mode PPPoE").
2575 2576 2577 2578 2579 2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604

config PPPOATM
	tristate "PPP over ATM"
	depends on ATM && PPP
	help
	  Support PPP (Point to Point Protocol) encapsulated in ATM frames.
	  This implementation does not yet comply with section 8 of RFC2364,
	  which can lead to bad results if the ATM peer loses state and
	  changes its encapsulation unilaterally.

config SLIP
	tristate "SLIP (serial line) support"
	depends on NETDEVICES
	---help---
	  Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
	  connect to your Internet service provider or to connect to some
	  other local Unix box or if you want to configure your Linux box as a
	  Slip/CSlip server for other people to dial in. SLIP (Serial Line
	  Internet Protocol) is a protocol used to send Internet traffic over
	  serial connections such as telephone lines or null modem cables;
	  nowadays, the protocol PPP is more commonly used for this same
	  purpose.

	  Normally, your access provider has to support SLIP in order for you
	  to be able to use it, but there is now a SLIP emulator called SLiRP
	  around (available from
	  <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
	  allows you to use SLIP over a regular dial up shell connection. If
	  you plan to use SLiRP, make sure to say Y to CSLIP, below. The
	  NET-3-HOWTO, available from
2605
	  <http://www.tldp.org/docs.html#howto>, explains how to
2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616
	  configure SLIP. Note that you don't need this option if you just
	  want to run term (term is a program which gives you almost full
	  Internet connectivity if you have a regular dial up shell account on
	  some Internet connected Unix computer. Read
	  <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
	  support will enlarge your kernel by about 4 KB. If unsure, say N.

	  If you want to compile this as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want),
	  say M here and read <file:Documentation/modules.txt> as well as
	  <file:Documentation/networking/net-modules.txt>. The module will be
2617
	  called slip.
2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 2629 2630

config SLIP_COMPRESSED
	bool "CSLIP compressed headers"
	depends on SLIP
	---help---
	  This protocol is faster than SLIP because it uses compression on the
	  TCP/IP headers (not on the data itself), but it has to be supported
	  on both ends. Ask your access provider if you are not sure and
	  answer Y, just in case. You will still be able to use plain SLIP. If
	  you plan to use SLiRP, the SLIP emulator (available from
	  <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
	  allows you to use SLIP over a regular dial up shell connection, you
	  definitely want to say Y here. The NET-3-HOWTO, available from
2631
	  <http://www.tldp.org/docs.html#howto>, explains how to configure
2632 2633 2634 2635 2636 2637 2638 2639 2640 2641 2642 2643 2644 2645 2646 2647 2648 2649 2650 2651 2652 2653 2654 2655 2656 2657 2658 2659
	  CSLIP. This won't enlarge your kernel.

config SLIP_SMART
	bool "Keepalive and linefill"
	depends on SLIP
	help
	  Adds additional capabilities to the SLIP driver to support the
	  RELCOM line fill and keepalive monitoring. Ideal on poor quality
	  analogue lines.

config SLIP_MODE_SLIP6
	bool "Six bit SLIP encapsulation"
	depends on SLIP
	help
	  Just occasionally you may need to run IP over hostile serial
	  networks that don't pass all control characters or are only seven
	  bit. Saying Y here adds an extra mode you can use with SLIP:
	  "slip6". In this mode, SLIP will only send normal ASCII symbols over
	  the serial device. Naturally, this has to be supported at the other
	  end of the link as well. It's good enough, for example, to run IP
	  over the async ports of a Camtec JNT Pad. If unsure, say N.

source "drivers/net/wireless/Kconfig"

source "drivers/net/tokenring/Kconfig"

config NET_FC
	bool "Fibre Channel driver support"
2660
	depends on NETDEVICES && SCSI && PCI
2661 2662 2663 2664 2665 2666 2667 2668 2669 2670 2671 2672 2673 2674 2675 2676 2677 2678
	help
	  Fibre Channel is a high speed serial protocol mainly used to connect
	  large storage devices to the computer; it is compatible with and
	  intended to replace SCSI.

	  If you intend to use Fibre Channel, you need to have a Fibre channel
	  adaptor card in your computer; say Y here and to the driver for your
	  adaptor below. You also should have said Y to "SCSI support" and
	  "SCSI generic support".

config IPHASE5526
	tristate "Interphase 5526 Tachyon chipset based adapter support"
	depends on NET_FC && SCSI && PCI
	help
	  Say Y here if you have a Fibre Channel adaptor of this kind.

	  The driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
2679
	  The module will be called iph5526. For general information about
2680 2681 2682 2683 2684 2685 2686 2687 2688
	  modules read <file:Documentation/modules.txt>.

config RCPCI
	tristate "Red Creek Hardware VPN (EXPERIMENTAL)"
	depends on NETDEVICES && EXPERIMENTAL && PCI
	help
	  This is a driver for hardware which provides a Virtual Private
	  Network (VPN). Say Y if you have it.

2689
	  This code is also available as a module called rcpci ( = code
2690 2691 2692 2693 2694 2695 2696 2697 2698 2699 2700 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713
	  which can be inserted in and removed from the running kernel
	  whenever you want). If you want to compile it as a module, say M
	  here and read <file:Documentation/modules.txt>.

config SHAPER
	tristate "Traffic Shaper (EXPERIMENTAL)"
	depends on NETDEVICES && EXPERIMENTAL
	---help---
	  The traffic shaper is a virtual network device that allows you to
	  limit the rate of outgoing data flow over some other network device.
	  The traffic that you want to slow down can then be routed through
	  these virtual devices. See
	  <file:Documentation/networking/shaper.txt> for more information.

	  An alternative to this traffic shaper is the experimental
	  Class-Based Queueing (CBQ) scheduling support which you get if you
	  say Y to "QoS and/or fair queueing" above.

	  To set up and configure shaper devices, you need the shapecfg
	  program, available from <ftp://shadow.cabi.net/pub/Linux/> in the
	  shaper package.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
2714
	  The module will be called shaper.  If you want to compile it as a
2715 2716 2717 2718 2719 2720 2721
	  module, say M here and read <file:Documentation/modules.txt>.  If
	  unsure, say N.

source "drivers/net/wan/Kconfig"

source "drivers/net/pcmcia/Kconfig"

2722
source "drivers/atm/Kconfig"
2723 2724

source "drivers/s390/net/Kconfig"