ARM: dts: sbc-t3x30: add audio support

Add audio related DT nodes
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -155,6 +155,15 @@ OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
+
+	mcbsp2_pins: pinmux_mcbsp2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx */
+			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)	/* mcbsp2_clkx */
+			OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)	/* mcbsp2_dr */
+			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)	/* mcbsp2_dx */
+		>;
+	};
 };
 
 &uart3 {
@@ -243,3 +252,10 @@ venc_out: endpoint {
 		};
 	};
 };
+
+&mcbsp2 {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+};

arch/arm/boot/dts/omap3-cm-t3x30.dtsi

@@ -10,6 +10,14 @@ cpu@0 {
 			cpu0-supply = <&vcc>;
 		};
 	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "cm-t35";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
 };
 
 &omap3_pmx_core {
@@ -59,6 +67,12 @@ twl: twl@48 {
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
 	};
 };
 

arch/arm/boot/dts/omap3-sb-t35.dtsi

@@ -43,6 +43,16 @@ dvi_connector_in: endpoint {
 			};
 		};
 	};
+
+	audio_amp: audio_amp {
+		compatible = "regulator-fixed";
+		regulator-name = "audio_amp";
+		pinctrl-names = "default";
+		pinctrl-0 = <&sb_t35_audio_amp>;
+		gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;   /* gpio_61 */
+		enable-active-low;
+		regulator-always-on;
+	};
 };
 
 &omap3_pmx_core {
@@ -65,6 +75,12 @@ OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
 		>;
 	};
+
+	sb_t35_audio_amp: pinmux_sb_t35_audio_amp {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4) /* gpmc_nbe1.gpio_61 */
+		>;
+	};
 };
 
 &i2c3 {