ARM: dts: stm32: add a new DCMI pins group on stm32mp15

The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output.
stm32mp15-pinctrl.dtsi contained one pin state definition for the DCMI
interface, dcmi-0, AKA phandle dcmi_pins_a. This definition was
incompatible with the pins used on the Odyssey board, where:
- there are 8 data pins instead of 12,
- DCMI_HSYNC is available at PA4 instead of PH8,
- DCMI_D0 is at PC6 instead of PH9,
- DCMI_D3 is at PE1 instead of PH12,
- DCMI_D4 is at PE11 instead of PH14,
- DCMI_D5 is at PD3 instead of PI4,
- DCMI_D6 is at PE13 instead of PB8,
- DCMI_D7 is at PB9 instead of PE6.

Add the DCMI pins used on the Odyssey board as a new DCMI pin state
definition, dcmi-1, AKA phandle dcmi_pins_b.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

arch/arm/boot/dts/stm32mp15-pinctrl.dtsi

@@ -118,6 +118,39 @@ pins {
 		};
 	};
 
+	dcmi_pins_b: dcmi-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('C', 6,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1,  AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('E', 11, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('D', 3,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('E', 13, AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('B', 9,  AF13)>;/* DCMI_D7 */
+			bias-disable;
+		};
+	};
+
+	dcmi_sleep_pins_b: dcmi-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('C', 6,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1,  ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('E', 11, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('D', 3,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('E', 13, ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('B', 9,  ANALOG)>;/* DCMI_D7 */
+		};
+	};
+
 	ethernet0_rgmii_pins_a: rgmii-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */