Commit 02bc6e54 authored by Vivien Didelot's avatar Vivien Didelot Committed by David S. Miller

net: dsa: introduce dsa_user_ports helper

Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: default avatarVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 4a5b85ff
......@@ -688,7 +688,7 @@ mt7530_cpu_port_enable(struct mt7530_priv *priv,
* the switch
*/
mt7530_write(priv, MT7530_PCR_P(port),
PCR_MATRIX(priv->ds->enabled_port_mask));
PCR_MATRIX(dsa_user_ports(priv->ds)));
return 0;
}
......
......@@ -175,8 +175,7 @@ static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
*/
REG_WRITE(addr, PORT_VLAN_MAP,
((p & 0xf) << PORT_VLAN_MAP_DBNUM_SHIFT) |
(dsa_is_cpu_port(ds, p) ?
ds->enabled_port_mask :
(dsa_is_cpu_port(ds, p) ? dsa_user_ports(ds) :
BIT(dsa_to_port(ds, p)->cpu_dp->index)));
/* Port Association Vector: when learning source addresses
......
......@@ -551,8 +551,7 @@ qca8k_setup(struct dsa_switch *ds)
/* CPU port gets connected to all user ports of the switch */
if (dsa_is_cpu_port(ds, i)) {
qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT),
QCA8K_PORT_LOOKUP_MEMBER,
ds->enabled_port_mask);
QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
}
/* Invividual user ports get connected to CPU port only */
......
......@@ -276,6 +276,11 @@ static inline bool dsa_is_user_port(struct dsa_switch *ds, int p)
return !!(ds->enabled_port_mask & BIT(p));
}
static inline u32 dsa_user_ports(struct dsa_switch *ds)
{
return ds->enabled_port_mask;
}
static inline const struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
{
return &ds->ports[p];
......
......@@ -312,7 +312,7 @@ static int dsa_ds_apply(struct dsa_switch_tree *dst, struct dsa_switch *ds)
* the slave MDIO bus driver rely on these values for probing PHY
* devices or not
*/
ds->phys_mii_mask = ds->enabled_port_mask;
ds->phys_mii_mask |= dsa_user_ports(ds);
/* Add the switch to devlink before calling setup, so that setup can
* add dpipe tables
......
......@@ -136,7 +136,7 @@ static int dsa_switch_setup_one(struct dsa_switch *ds,
/* Make the built-in MII bus mask match the number of ports,
* switch drivers can override this later
*/
ds->phys_mii_mask = ds->enabled_port_mask;
ds->phys_mii_mask |= dsa_user_ports(ds);
/*
* If the CPU connects to this switch, set the switch tree
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment