Commit 04790537 authored by Robert Nelson's avatar Robert Nelson Committed by Tony Lindgren

ARM: dts: Add am335x-pocketbeagle

PocketBeagle is an ultra-tiny-yet-complete open-source USB-key-fob computer.

This board family can be indentified by the A335PBGL in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35  50 42 47 4c 30 30 41 32 |.U3.A335PBGL00A2|]

http://beagleboard.org/pocket
https://github.com/beagleboard/pocketbeagleSigned-off-by: default avatarRobert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
CC: Peter Robinson <pbrobinson@redhat.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent b74c2b21
......@@ -688,6 +688,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-pdu001.dtb \
am335x-pepper.dtb \
am335x-phycore-rdk.dtb \
am335x-pocketbeagle.dtb \
am335x-shc.dtb \
am335x-sbc-t335.dtb \
am335x-sl50.dtb \
......
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* Author: Robert Nelson <robertcnelson@gmail.com>
*/
/ {
cpus {
cpu@0 {
cpu0-supply = <&dcdc2_reg>;
};
};
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x20000000>; /* 512 MB */
};
};
&cpu0_opp_table {
/*
* Octavo Systems:
* The EFUSE_SMA register is not programmed for any of the AM335x wafers
* we get and we are not programming them during our production test.
* Therefore, from a DEVICE_ID revision point of view, the silicon looks
* like it is Revision 2.1. However, from an EFUSE_SMA point of view for
* the HW OPP table, the silicon looks like it is Revision 1.0 (ie the
* EFUSE_SMA register reads as all zeros).
*/
oppnitro-1000000000 {
opp-supported-hw = <0x06 0x0100>;
};
};
&am33xx_pinmux {
i2c0_pins: pinmux-i2c0-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* (C17) I2C0_SDA.I2C0_SDA */
AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* (C16) I2C0_SCL.I2C0_SCL */
>;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
clock-frequency = <400000>;
tps: tps@24 {
reg = <0x24>;
};
};
/include/ "tps65217.dtsi"
&tps {
interrupts = <7>; /* NMI */
interrupt-parent = <&intc>;
ti,pmic-shutdown-controller;
pwrbutton {
interrupts = <2>;
status = "okay";
};
regulators {
dcdc1_reg: regulator@0 {
regulator-name = "vdds_dpr";
regulator-always-on;
};
dcdc2_reg: regulator@1 {
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
regulator-min-microvolt = <925000>;
regulator-max-microvolt = <1351500>;
regulator-boot-on;
regulator-always-on;
};
dcdc3_reg: regulator@2 {
/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
regulator-name = "vdd_core";
regulator-min-microvolt = <925000>;
regulator-max-microvolt = <1150000>;
regulator-boot-on;
regulator-always-on;
};
ldo1_reg: regulator@3 {
regulator-name = "vio,vrtc,vdds";
regulator-always-on;
};
ldo2_reg: regulator@4 {
regulator-name = "vdd_3v3aux";
regulator-always-on;
};
ldo3_reg: regulator@5 {
regulator-name = "vdd_1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo4_reg: regulator@6 {
regulator-name = "vdd_3v3a";
regulator-always-on;
};
};
};
&aes {
status = "okay";
};
&sham {
status = "okay";
};
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* Author: Robert Nelson <robertcnelson@gmail.com>
*/
/dts-v1/;
#include "am33xx.dtsi"
#include "am335x-osd335x-common.dtsi"
/ {
model = "TI AM335x PocketBeagle";
compatible = "ti,am335x-pocketbeagle", "ti,am335x-bone", "ti,am33xx";
chosen {
stdout-path = &uart0;
};
leds {
pinctrl-names = "default";
pinctrl-0 = <&usr_leds_pins>;
compatible = "gpio-leds";
usr0 {
label = "beaglebone:green:usr0";
gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
usr1 {
label = "beaglebone:green:usr1";
gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
usr2 {
label = "beaglebone:green:usr2";
gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "cpu0";
default-state = "off";
};
usr3 {
label = "beaglebone:green:usr3";
gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
vmmcsd_fixed: fixedregulator0 {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&am33xx_pinmux {
i2c2_pins: pinmux-i2c2-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */
AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* (D18) uart1_ctsn.I2C2_SDA */
>;
};
ehrpwm0_pins: pinmux-ehrpwm0-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* (A13) mcasp0_aclkx.ehrpwm0A */
>;
};
ehrpwm1_pins: pinmux-ehrpwm1-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U14) gpmc_a2.ehrpwm1A */
>;
};
mmc0_pins: pinmux-mmc0-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* (C15) spi0_cs1.gpio0[6] */
AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* (G16) mmc0_dat0.mmc0_dat0 */
AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* (G15) mmc0_dat1.mmc0_dat1 */
AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* (F18) mmc0_dat2.mmc0_dat2 */
AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* (F17) mmc0_dat3.mmc0_dat3 */
AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* (G18) mmc0_cmd.mmc0_cmd */
AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* (G17) mmc0_clk.mmc0_clk */
AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* (B12) mcasp0_aclkr.mmc0_sdwp */
>;
};
spi0_pins: pinmux-spi0-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* (A17) spi0_sclk.spi0_sclk */
AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */
AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */
AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */
>;
};
spi1_pins: pinmux-spi1-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x964, PIN_INPUT_PULLUP | MUX_MODE4) /* (C18) eCAP0_in_PWM0_out.spi1_sclk */
AM33XX_IOPAD(0x968, PIN_INPUT_PULLUP | MUX_MODE4) /* (E18) uart0_ctsn.spi1_d0 */
AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE4) /* (E17) uart0_rtsn.spi1_d1 */
AM33XX_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE4) /* (A15) xdma_event_intr0.spi1_cs1 */
>;
};
usr_leds_pins: pinmux-usr-leds-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) /* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */
AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7) /* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */
AM33XX_IOPAD(0x85c, PIN_OUTPUT | MUX_MODE7) /* (T15) gpmc_a7.gpio1[23] - USR_LED_2 */
AM33XX_IOPAD(0x860, PIN_OUTPUT | MUX_MODE7) /* (V16) gpmc_a8.gpio1[24] - USR_LED_3 */
>;
};
uart0_pins: pinmux-uart0-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* (E15) uart0_rxd.uart0_rxd */
AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* (E16) uart0_txd.uart0_txd */
>;
};
uart4_pins: pinmux-uart4-pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */
AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U17) gpmc_wpn.uart4_txd */
>;
};
};
&epwmss0 {
status = "okay";
};
&ehrpwm0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&ehrpwm0_pins>;
};
&epwmss1 {
status = "okay";
};
&ehrpwm1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&ehrpwm1_pins>;
};
&i2c0 {
eeprom: eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "okay";
clock-frequency = <400000>;
};
&mmc1 {
status = "okay";
vmmc-supply = <&vmmcsd_fixed>;
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
&rtc {
system-power-controller;
};
&tscadc {
status = "okay";
adc {
ti,adc-channels = <0 1 2 3 4 5 6 7>;
ti,chan-step-avg = <16 16 16 16 16 16 16 16>;
ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>;
ti,chan-step-sampledelay = <0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins>;
status = "okay";
};
&usb {
status = "okay";
};
&usb_ctrl_mod {
status = "okay";
};
&usb0_phy {
status = "okay";
};
&usb0 {
status = "okay";
dr_mode = "otg";
};
&usb1_phy {
status = "okay";
};
&usb1 {
status = "okay";
dr_mode = "host";
};
&cppi41dma {
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment