Merge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6

* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
  gpio/pch_gpio: Support new device ML7223
  gpio: make gpio_{request,free}_array gpio array parameter const
  GPIO: OMAP: move to drivers/gpio
  GPIO: OMAP: move register offset defines into <plat/gpio.h>
  gpio: Convert gpio_is_valid to return bool
  gpio: Move the s5pc100 GPIO to drivers/gpio
  gpio: Move the s5pv210 GPIO to drivers/gpio
  gpio: Move the exynos4 GPIO to drivers/gpio
  gpio: Move to Samsung common GPIO library to drivers/gpio
  gpio/nomadik: add function to read GPIO pull down status
  gpio/nomadik: show all pins in debug
  gpio: move Nomadik GPIO driver to drivers/gpio
  gpio: move U300 GPIO driver to drivers/gpio
  langwell_gpio: add runtime pm support
  gpio/pca953x: Add support for pca9574 and pca9575 devices
  gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535

arch/arm/mach-exynos4/Makefile

@@ -13,7 +13,7 @@ obj-				:=
 # Core support for EXYNOS4 system
 
 obj-$(CONFIG_CPU_EXYNOS4210)	+= cpu.o init.o clock.o irq-combiner.o
-obj-$(CONFIG_CPU_EXYNOS4210)	+= setup-i2c0.o gpiolib.o irq-eint.o dma.o
+obj-$(CONFIG_CPU_EXYNOS4210)	+= setup-i2c0.o irq-eint.o dma.o
 obj-$(CONFIG_PM)		+= pm.o sleep.o
 obj-$(CONFIG_CPU_FREQ)		+= cpufreq.o
 obj-$(CONFIG_CPU_IDLE)		+= cpuidle.o

arch/arm/mach-nomadik/Kconfig

@@ -6,7 +6,6 @@ config MACH_NOMADIK_8815NHK
 	bool "ST 8815 Nomadik Hardware Kit (evaluation board)"
 	select NOMADIK_8815
 	select HAS_MTU
-	select NOMADIK_GPIO
 
 endmenu
 

arch/arm/mach-s5pc100/Makefile

@@ -11,7 +11,7 @@ obj-				:=
 
 # Core support for S5PC100 system
 
-obj-$(CONFIG_CPU_S5PC100)	+= cpu.o init.o clock.o gpiolib.o
+obj-$(CONFIG_CPU_S5PC100)	+= cpu.o init.o clock.o
 obj-$(CONFIG_CPU_S5PC100)	+= setup-i2c0.o
 obj-$(CONFIG_CPU_S5PC100)	+= dma.o
 

arch/arm/mach-s5pv210/Makefile

@@ -12,7 +12,7 @@ obj-				:=
 
 # Core support for S5PV210 system
 
-obj-$(CONFIG_CPU_S5PV210)	+= cpu.o init.o clock.o dma.o gpiolib.o
+obj-$(CONFIG_CPU_S5PV210)	+= cpu.o init.o clock.o dma.o
 obj-$(CONFIG_CPU_S5PV210)	+= setup-i2c0.o
 obj-$(CONFIG_S5PV210_PM)	+= pm.o sleep.o
 obj-$(CONFIG_CPU_FREQ)		+= cpufreq.o

arch/arm/mach-u300/Makefile

@@ -2,7 +2,7 @@
 # Makefile for the linux kernel, U300 machine.
 #
 
-obj-y		:= core.o clock.o timer.o gpio.o padmux.o
+obj-y		:= core.o clock.o timer.o padmux.o
 obj-m		:=
 obj-n		:=
 obj-		:=

arch/arm/mach-ux500/Kconfig

@@ -5,7 +5,6 @@ config UX500_SOC_COMMON
 	default y
 	select ARM_GIC
 	select HAS_MTU
-	select NOMADIK_GPIO
 	select ARM_ERRATA_753970
 
 menu "Ux500 SoC"

arch/arm/plat-nomadik/Kconfig

@@ -21,9 +21,4 @@ config HAS_MTU
 	  to multiple interrupt generating programmable
 	  32-bit free running decrementing counters.
 
-config NOMADIK_GPIO
-	bool
-	help
-	  Support for the Nomadik GPIO controller.
-
 endif

arch/arm/plat-nomadik/Makefile

@@ -3,4 +3,3 @@
 # Licensed under GPLv2
 
 obj-$(CONFIG_HAS_MTU)	+= timer.o
-obj-$(CONFIG_NOMADIK_GPIO)	+= gpio.o

arch/arm/plat-nomadik/include/plat/gpio.h

@@ -78,6 +78,8 @@ extern int nmk_gpio_get_mode(int gpio);
 extern void nmk_gpio_wakeups_suspend(void);
 extern void nmk_gpio_wakeups_resume(void);
 
+extern void nmk_gpio_read_pull(int gpio_bank, u32 *pull_up);
+
 /*
  * Platform data to register a block: only the initial gpio/irq number.
  */

arch/arm/plat-omap/Makefile

@@ -3,7 +3,7 @@
 #
 
 # Common support
-obj-y := common.o sram.o clock.o devices.o dma.o mux.o gpio.o \
+obj-y := common.o sram.o clock.o devices.o dma.o mux.o \
 	 usb.o fb.o io.o counter_32k.o
 obj-m :=
 obj-n :=

arch/arm/plat-omap/include/plat/gpio.h

@@ -52,6 +52,109 @@
 
 #define OMAP34XX_NR_GPIOS		6
 
+/*
+ * OMAP1510 GPIO registers
+ */
+#define OMAP1510_GPIO_DATA_INPUT	0x00
+#define OMAP1510_GPIO_DATA_OUTPUT	0x04
+#define OMAP1510_GPIO_DIR_CONTROL	0x08
+#define OMAP1510_GPIO_INT_CONTROL	0x0c
+#define OMAP1510_GPIO_INT_MASK		0x10
+#define OMAP1510_GPIO_INT_STATUS	0x14
+#define OMAP1510_GPIO_PIN_CONTROL	0x18
+
+#define OMAP1510_IH_GPIO_BASE		64
+
+/*
+ * OMAP1610 specific GPIO registers
+ */
+#define OMAP1610_GPIO_REVISION		0x0000
+#define OMAP1610_GPIO_SYSCONFIG		0x0010
+#define OMAP1610_GPIO_SYSSTATUS		0x0014
+#define OMAP1610_GPIO_IRQSTATUS1	0x0018
+#define OMAP1610_GPIO_IRQENABLE1	0x001c
+#define OMAP1610_GPIO_WAKEUPENABLE	0x0028
+#define OMAP1610_GPIO_DATAIN		0x002c
+#define OMAP1610_GPIO_DATAOUT		0x0030
+#define OMAP1610_GPIO_DIRECTION		0x0034
+#define OMAP1610_GPIO_EDGE_CTRL1	0x0038
+#define OMAP1610_GPIO_EDGE_CTRL2	0x003c
+#define OMAP1610_GPIO_CLEAR_IRQENABLE1	0x009c
+#define OMAP1610_GPIO_CLEAR_WAKEUPENA	0x00a8
+#define OMAP1610_GPIO_CLEAR_DATAOUT	0x00b0
+#define OMAP1610_GPIO_SET_IRQENABLE1	0x00dc
+#define OMAP1610_GPIO_SET_WAKEUPENA	0x00e8
+#define OMAP1610_GPIO_SET_DATAOUT	0x00f0
+
+/*
+ * OMAP7XX specific GPIO registers
+ */
+#define OMAP7XX_GPIO_DATA_INPUT		0x00
+#define OMAP7XX_GPIO_DATA_OUTPUT	0x04
+#define OMAP7XX_GPIO_DIR_CONTROL	0x08
+#define OMAP7XX_GPIO_INT_CONTROL	0x0c
+#define OMAP7XX_GPIO_INT_MASK		0x10
+#define OMAP7XX_GPIO_INT_STATUS		0x14
+
+/*
+ * omap2+ specific GPIO registers
+ */
+#define OMAP24XX_GPIO_REVISION		0x0000
+#define OMAP24XX_GPIO_IRQSTATUS1	0x0018
+#define OMAP24XX_GPIO_IRQSTATUS2	0x0028
+#define OMAP24XX_GPIO_IRQENABLE2	0x002c
+#define OMAP24XX_GPIO_IRQENABLE1	0x001c
+#define OMAP24XX_GPIO_WAKE_EN		0x0020
+#define OMAP24XX_GPIO_CTRL		0x0030
+#define OMAP24XX_GPIO_OE		0x0034
+#define OMAP24XX_GPIO_DATAIN		0x0038
+#define OMAP24XX_GPIO_DATAOUT		0x003c
+#define OMAP24XX_GPIO_LEVELDETECT0	0x0040
+#define OMAP24XX_GPIO_LEVELDETECT1	0x0044
+#define OMAP24XX_GPIO_RISINGDETECT	0x0048
+#define OMAP24XX_GPIO_FALLINGDETECT	0x004c
+#define OMAP24XX_GPIO_DEBOUNCE_EN	0x0050
+#define OMAP24XX_GPIO_DEBOUNCE_VAL	0x0054
+#define OMAP24XX_GPIO_CLEARIRQENABLE1	0x0060
+#define OMAP24XX_GPIO_SETIRQENABLE1	0x0064
+#define OMAP24XX_GPIO_CLEARWKUENA	0x0080
+#define OMAP24XX_GPIO_SETWKUENA		0x0084
+#define OMAP24XX_GPIO_CLEARDATAOUT	0x0090
+#define OMAP24XX_GPIO_SETDATAOUT	0x0094
+
+#define OMAP4_GPIO_REVISION		0x0000
+#define OMAP4_GPIO_EOI			0x0020
+#define OMAP4_GPIO_IRQSTATUSRAW0	0x0024
+#define OMAP4_GPIO_IRQSTATUSRAW1	0x0028
+#define OMAP4_GPIO_IRQSTATUS0		0x002c
+#define OMAP4_GPIO_IRQSTATUS1		0x0030
+#define OMAP4_GPIO_IRQSTATUSSET0	0x0034
+#define OMAP4_GPIO_IRQSTATUSSET1	0x0038
+#define OMAP4_GPIO_IRQSTATUSCLR0	0x003c
+#define OMAP4_GPIO_IRQSTATUSCLR1	0x0040
+#define OMAP4_GPIO_IRQWAKEN0		0x0044
+#define OMAP4_GPIO_IRQWAKEN1		0x0048
+#define OMAP4_GPIO_IRQENABLE1		0x011c
+#define OMAP4_GPIO_WAKE_EN		0x0120
+#define OMAP4_GPIO_IRQSTATUS2		0x0128
+#define OMAP4_GPIO_IRQENABLE2		0x012c
+#define OMAP4_GPIO_CTRL			0x0130
+#define OMAP4_GPIO_OE			0x0134
+#define OMAP4_GPIO_DATAIN		0x0138
+#define OMAP4_GPIO_DATAOUT		0x013c
+#define OMAP4_GPIO_LEVELDETECT0		0x0140
+#define OMAP4_GPIO_LEVELDETECT1		0x0144
+#define OMAP4_GPIO_RISINGDETECT		0x0148
+#define OMAP4_GPIO_FALLINGDETECT	0x014c
+#define OMAP4_GPIO_DEBOUNCENABLE	0x0150
+#define OMAP4_GPIO_DEBOUNCINGTIME	0x0154
+#define OMAP4_GPIO_CLEARIRQENABLE1	0x0160
+#define OMAP4_GPIO_SETIRQENABLE1	0x0164
+#define OMAP4_GPIO_CLEARWKUENA		0x0180
+#define OMAP4_GPIO_SETWKUENA		0x0184
+#define OMAP4_GPIO_CLEARDATAOUT		0x0190
+#define OMAP4_GPIO_SETDATAOUT		0x0194
+
 #define OMAP_MPUIO(nr)		(OMAP_MAX_GPIO_LINES + (nr))
 #define OMAP_GPIO_IS_MPUIO(nr)	((nr) >= OMAP_MAX_GPIO_LINES)
 

arch/arm/plat-samsung/Makefile

@@ -19,7 +19,6 @@ obj-y				+= gpio.o
 obj-y				+= gpio-config.o
 obj-y				+= dev-asocdma.o
 
-obj-$(CONFIG_SAMSUNG_GPIOLIB_4BIT)	+= gpiolib.o
 obj-$(CONFIG_SAMSUNG_CLKSRC)	+= clock-clksrc.o
 
 obj-$(CONFIG_SAMSUNG_IRQ_UART)	+= irq-uart.o

drivers/gpio/Kconfig

@@ -86,6 +86,30 @@ config GPIO_IT8761E
 	help
 	  Say yes here to support GPIO functionality of IT8761E super I/O chip.
 
+config GPIO_EXYNOS4
+	bool "Samsung Exynos4 GPIO library support"
+	default y if CPU_EXYNOS4210
+	help
+	  Say yes here to support Samsung Exynos4 series SoCs GPIO library
+
+config GPIO_PLAT_SAMSUNG
+	bool "Samsung SoCs GPIO library support"
+	default y if SAMSUNG_GPIOLIB_4BIT
+	help
+	  Say yes here to support Samsung SoCs GPIO library
+
+config GPIO_S5PC100
+	bool "Samsung S5PC100 GPIO library support"
+	default y if CPU_S5PC100
+	help
+	  Say yes here to support Samsung S5PC100 SoCs GPIO library
+
+config GPIO_S5PV210
+	bool "Samsung S5PV210/S5PC110 GPIO library support"
+	default y if CPU_S5PV210
+	help
+	  Say yes here to support Samsung S5PV210/S5PC110 SoCs GPIO library
+
 config GPIO_PL061
 	bool "PrimeCell PL061 GPIO support"
 	depends on ARM_AMBA
@@ -303,7 +327,7 @@ comment "PCI GPIO expanders:"
 
 config GPIO_CS5535
 	tristate "AMD CS5535/CS5536 GPIO support"
-	depends on PCI && X86 && !CS5535_GPIO
+	depends on PCI && X86 && !CS5535_GPIO && MFD_CS5535
 	help
 	  The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
 	  can be used for quite a number of things.  The CS5535/6 is found on
@@ -334,13 +358,19 @@ config GPIO_LANGWELL
 	  Say Y here to support Intel Langwell/Penwell GPIO.
 
 config GPIO_PCH
-	tristate "PCH GPIO of Intel Topcliff"
+	tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GPIO"
 	depends on PCI && X86
 	help
 	  This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
 	  which is an IOH(Input/Output Hub) for x86 embedded processor.
 	  This driver can access PCH GPIO device.
 
+	  This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
+	  Output Hub), ML7223.
+	  ML7223 IOH is for MP(Media Phone) use.
+	  ML7223 is companion chip for Intel Atom E6xx series.
+	  ML7223 is completely compatible for Intel EG20T PCH.
+
 config GPIO_ML_IOH
 	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
 	depends on PCI

drivers/gpio/Makefile

@@ -8,6 +8,10 @@ obj-$(CONFIG_GPIO_ADP5520)	+= adp5520-gpio.o
 obj-$(CONFIG_GPIO_ADP5588)	+= adp5588-gpio.o
 obj-$(CONFIG_GPIO_BASIC_MMIO_CORE)	+= basic_mmio_gpio.o
 obj-$(CONFIG_GPIO_BASIC_MMIO)	+= basic_mmio_gpio.o
+obj-$(CONFIG_GPIO_EXYNOS4)	+= gpio-exynos4.o
+obj-$(CONFIG_GPIO_PLAT_SAMSUNG)	+= gpio-plat-samsung.o
+obj-$(CONFIG_GPIO_S5PC100)	+= gpio-s5pc100.o
+obj-$(CONFIG_GPIO_S5PV210)	+= gpio-s5pv210.o
 obj-$(CONFIG_GPIO_LANGWELL)	+= langwell_gpio.o
 obj-$(CONFIG_GPIO_MAX730X)	+= max730x.o
 obj-$(CONFIG_GPIO_MAX7300)	+= max7300.o
@@ -16,6 +20,7 @@ obj-$(CONFIG_GPIO_MAX732X)	+= max732x.o
 obj-$(CONFIG_GPIO_MC33880)	+= mc33880.o
 obj-$(CONFIG_GPIO_MCP23S08)	+= mcp23s08.o
 obj-$(CONFIG_GPIO_74X164)	+= 74x164.o
+obj-$(CONFIG_ARCH_OMAP)         += gpio-omap.o
 obj-$(CONFIG_GPIO_PCA953X)	+= pca953x.o
 obj-$(CONFIG_GPIO_PCF857X)	+= pcf857x.o
 obj-$(CONFIG_GPIO_PCH)		+= pch_gpio.o
@@ -34,6 +39,8 @@ obj-$(CONFIG_GPIO_WM831X)	+= wm831x-gpio.o
 obj-$(CONFIG_GPIO_WM8350)	+= wm8350-gpiolib.o
 obj-$(CONFIG_GPIO_WM8994)	+= wm8994-gpio.o
 obj-$(CONFIG_GPIO_SCH)		+= sch_gpio.o
+obj-$(CONFIG_MACH_U300)		+= gpio-u300.o
+obj-$(CONFIG_PLAT_NOMADIK)	+= gpio-nomadik.o
 obj-$(CONFIG_GPIO_RDC321X)	+= rdc321x-gpio.o
 obj-$(CONFIG_GPIO_JANZ_TTL)	+= janz-ttl.o
 obj-$(CONFIG_GPIO_SX150X)	+= sx150x.o

arch/arm/plat-nomadik/gpio.c → drivers/gpio/gpio-nomadik.c

@@ -57,6 +57,7 @@ struct nmk_gpio_chip {
 	u32 fwimsc;
 	u32 slpm;
 	u32 enabled;
+	u32 pull_up;
 };
 
 static struct nmk_gpio_chip *
@@ -103,16 +104,22 @@ static void __nmk_gpio_set_pull(struct nmk_gpio_chip *nmk_chip,
 	u32 pdis;
 
 	pdis = readl(nmk_chip->addr + NMK_GPIO_PDIS);
-	if (pull == NMK_GPIO_PULL_NONE)
+	if (pull == NMK_GPIO_PULL_NONE) {
 		pdis |= bit;
-	else
+		nmk_chip->pull_up &= ~bit;
+	} else {
 		pdis &= ~bit;
+	}
+
 	writel(pdis, nmk_chip->addr + NMK_GPIO_PDIS);
 
-	if (pull == NMK_GPIO_PULL_UP)
+	if (pull == NMK_GPIO_PULL_UP) {
+		nmk_chip->pull_up |= bit;
 		writel(bit, nmk_chip->addr + NMK_GPIO_DATS);
-	else if (pull == NMK_GPIO_PULL_DOWN)
+	} else if (pull == NMK_GPIO_PULL_DOWN) {
+		nmk_chip->pull_up &= ~bit;
 		writel(bit, nmk_chip->addr + NMK_GPIO_DATC);
+	}
 }
 
 static void __nmk_gpio_make_input(struct nmk_gpio_chip *nmk_chip,
@@ -811,20 +818,43 @@ static void nmk_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 		bool pull;
 		u32 bit = 1 << i;
 
-		if (!label)
-			continue;
-
 		is_out = readl(nmk_chip->addr + NMK_GPIO_DIR) & bit;
 		pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & bit);
 		mode = nmk_gpio_get_mode(gpio);
 		seq_printf(s, " gpio-%-3d (%-20.20s) %s %s %s %s",
-			gpio, label,
+			gpio, label ?: "(none)",
 			is_out ? "out" : "in ",
 			chip->get
 				? (chip->get(chip, i) ? "hi" : "lo")
 				: "?  ",
 			(mode < 0) ? "unknown" : modes[mode],
 			pull ? "pull" : "none");
+
+		if (label && !is_out) {
+			int		irq = gpio_to_irq(gpio);
+			struct irq_desc	*desc = irq_to_desc(irq);
+
+			/* This races with request_irq(), set_irq_type(),
+			 * and set_irq_wake() ... but those are "rare".
+			 */
+			if (irq >= 0 && desc->action) {
+				char *trigger;
+				u32 bitmask = nmk_gpio_get_bitmask(gpio);
+
+				if (nmk_chip->edge_rising & bitmask)
+					trigger = "edge-rising";
+				else if (nmk_chip->edge_falling & bitmask)
+					trigger = "edge-falling";
+				else
+					trigger = "edge-undefined";
+
+				seq_printf(s, " irq-%d %s%s",
+					irq, trigger,
+					irqd_is_wakeup_set(&desc->irq_data)
+						? " wakeup" : "");
+			}
+		}
+
 		seq_printf(s, "\n");
 	}
 }
@@ -898,6 +928,25 @@ void nmk_gpio_wakeups_resume(void)
 	}
 }
 
+/*
+ * Read the pull up/pull down status.
+ * A bit set in 'pull_up' means that pull up
+ * is selected if pull is enabled in PDIS register.
+ * Note: only pull up/down set via this driver can
+ * be detected due to HW limitations.
+ */
+void nmk_gpio_read_pull(int gpio_bank, u32 *pull_up)
+{
+	if (gpio_bank < NUM_BANKS) {
+		struct nmk_gpio_chip *chip = nmk_gpio_chips[gpio_bank];
+
+		if (!chip)
+			return;
+
+		*pull_up = chip->pull_up;
+	}
+}
+
 static int __devinit nmk_gpio_probe(struct platform_device *dev)
 {
 	struct nmk_gpio_platform_data *pdata = dev->dev.platform_data;

arch/arm/plat-omap/gpio.c → drivers/gpio/gpio-omap.c

 /*
- *  linux/arch/arm/plat-omap/gpio.c
- *
  * Support functions for OMAP GPIO
  *
  * Copyright (C) 2003-2005 Nokia Corporation
@@ -30,109 +28,6 @@
 #include <mach/gpio.h>
 #include <asm/mach/irq.h>
 
-/*
- * OMAP1510 GPIO registers
- */
-#define OMAP1510_GPIO_DATA_INPUT	0x00
-#define OMAP1510_GPIO_DATA_OUTPUT	0x04
-#define OMAP1510_GPIO_DIR_CONTROL	0x08
-#define OMAP1510_GPIO_INT_CONTROL	0x0c
-#define OMAP1510_GPIO_INT_MASK		0x10
-#define OMAP1510_GPIO_INT_STATUS	0x14
-#define OMAP1510_GPIO_PIN_CONTROL	0x18
-
-#define OMAP1510_IH_GPIO_BASE		64
-
-/*
- * OMAP1610 specific GPIO registers
- */
-#define OMAP1610_GPIO_REVISION		0x0000
-#define OMAP1610_GPIO_SYSCONFIG		0x0010
-#define OMAP1610_GPIO_SYSSTATUS		0x0014
-#define OMAP1610_GPIO_IRQSTATUS1	0x0018
-#define OMAP1610_GPIO_IRQENABLE1	0x001c
-#define OMAP1610_GPIO_WAKEUPENABLE	0x0028
-#define OMAP1610_GPIO_DATAIN		0x002c
-#define OMAP1610_GPIO_DATAOUT		0x0030
-#define OMAP1610_GPIO_DIRECTION		0x0034
-#define OMAP1610_GPIO_EDGE_CTRL1	0x0038
-#define OMAP1610_GPIO_EDGE_CTRL2	0x003c
-#define OMAP1610_GPIO_CLEAR_IRQENABLE1	0x009c
-#define OMAP1610_GPIO_CLEAR_WAKEUPENA	0x00a8
-#define OMAP1610_GPIO_CLEAR_DATAOUT	0x00b0
-#define OMAP1610_GPIO_SET_IRQENABLE1	0x00dc
-#define OMAP1610_GPIO_SET_WAKEUPENA	0x00e8
-#define OMAP1610_GPIO_SET_DATAOUT	0x00f0
-
-/*
- * OMAP7XX specific GPIO registers
- */
-#define OMAP7XX_GPIO_DATA_INPUT		0x00
-#define OMAP7XX_GPIO_DATA_OUTPUT	0x04
-#define OMAP7XX_GPIO_DIR_CONTROL	0x08
-#define OMAP7XX_GPIO_INT_CONTROL	0x0c
-#define OMAP7XX_GPIO_INT_MASK		0x10
-#define OMAP7XX_GPIO_INT_STATUS		0x14
-
-/*
- * omap2+ specific GPIO registers
- */
-#define OMAP24XX_GPIO_REVISION		0x0000
-#define OMAP24XX_GPIO_IRQSTATUS1	0x0018
-#define OMAP24XX_GPIO_IRQSTATUS2	0x0028
-#define OMAP24XX_GPIO_IRQENABLE2	0x002c
-#define OMAP24XX_GPIO_IRQENABLE1	0x001c
-#define OMAP24XX_GPIO_WAKE_EN		0x0020
-#define OMAP24XX_GPIO_CTRL		0x0030
-#define OMAP24XX_GPIO_OE		0x0034
-#define OMAP24XX_GPIO_DATAIN		0x0038
-#define OMAP24XX_GPIO_DATAOUT		0x003c
-#define OMAP24XX_GPIO_LEVELDETECT0	0x0040
-#define OMAP24XX_GPIO_LEVELDETECT1	0x0044
-#define OMAP24XX_GPIO_RISINGDETECT	0x0048
-#define OMAP24XX_GPIO_FALLINGDETECT	0x004c
-#define OMAP24XX_GPIO_DEBOUNCE_EN	0x0050
-#define OMAP24XX_GPIO_DEBOUNCE_VAL	0x0054
-#define OMAP24XX_GPIO_CLEARIRQENABLE1	0x0060
-#define OMAP24XX_GPIO_SETIRQENABLE1	0x0064
-#define OMAP24XX_GPIO_CLEARWKUENA	0x0080
-#define OMAP24XX_GPIO_SETWKUENA		0x0084
-#define OMAP24XX_GPIO_CLEARDATAOUT	0x0090
-#define OMAP24XX_GPIO_SETDATAOUT	0x0094
-
-#define OMAP4_GPIO_REVISION		0x0000
-#define OMAP4_GPIO_EOI			0x0020
-#define OMAP4_GPIO_IRQSTATUSRAW0	0x0024
-#define OMAP4_GPIO_IRQSTATUSRAW1	0x0028
-#define OMAP4_GPIO_IRQSTATUS0		0x002c
-#define OMAP4_GPIO_IRQSTATUS1		0x0030
-#define OMAP4_GPIO_IRQSTATUSSET0	0x0034
-#define OMAP4_GPIO_IRQSTATUSSET1	0x0038
-#define OMAP4_GPIO_IRQSTATUSCLR0	0x003c
-#define OMAP4_GPIO_IRQSTATUSCLR1	0x0040
-#define OMAP4_GPIO_IRQWAKEN0		0x0044
-#define OMAP4_GPIO_IRQWAKEN1		0x0048
-#define OMAP4_GPIO_IRQENABLE1		0x011c
-#define OMAP4_GPIO_WAKE_EN		0x0120
-#define OMAP4_GPIO_IRQSTATUS2		0x0128
-#define OMAP4_GPIO_IRQENABLE2		0x012c
-#define OMAP4_GPIO_CTRL			0x0130
-#define OMAP4_GPIO_OE			0x0134
-#define OMAP4_GPIO_DATAIN		0x0138
-#define OMAP4_GPIO_DATAOUT		0x013c
-#define OMAP4_GPIO_LEVELDETECT0		0x0140
-#define OMAP4_GPIO_LEVELDETECT1		0x0144
-#define OMAP4_GPIO_RISINGDETECT		0x0148
-#define OMAP4_GPIO_FALLINGDETECT	0x014c
-#define OMAP4_GPIO_DEBOUNCENABLE	0x0150
-#define OMAP4_GPIO_DEBOUNCINGTIME	0x0154
-#define OMAP4_GPIO_CLEARIRQENABLE1	0x0160
-#define OMAP4_GPIO_SETIRQENABLE1	0x0164
-#define OMAP4_GPIO_CLEARWKUENA		0x0180
-#define OMAP4_GPIO_SETWKUENA		0x0184
-#define OMAP4_GPIO_CLEARDATAOUT		0x0190
-#define OMAP4_GPIO_SETDATAOUT		0x0194
-
 struct gpio_bank {
 	unsigned long pbase;
 	void __iomem *base;

drivers/gpio/gpiolib.c

@@ -1296,7 +1296,7 @@ EXPORT_SYMBOL_GPL(gpio_request_one);
  * @array:	array of the 'struct gpio'
  * @num:	how many GPIOs in the array
  */
-int gpio_request_array(struct gpio *array, size_t num)
+int gpio_request_array(const struct gpio *array, size_t num)
 {
 	int i, err;
 
@@ -1319,7 +1319,7 @@ EXPORT_SYMBOL_GPL(gpio_request_array);
  * @array:	array of the 'struct gpio'
  * @num:	how many GPIOs in the array
  */
-void gpio_free_array(struct gpio *array, size_t num)
+void gpio_free_array(const struct gpio *array, size_t num)
 {
 	while (num--)
 		gpio_free((array++)->gpio);

drivers/gpio/langwell_gpio.c

@@ -33,6 +33,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>
+#include <linux/pm_runtime.h>
 
 /*
  * Langwell chip has 64 pins and thus there are 2 32bit registers to control
@@ -63,6 +64,7 @@ struct lnw_gpio {
 	void				*reg_base;
 	spinlock_t			lock;
 	unsigned			irq_base;
+	struct pci_dev			*pdev;
 };
 
 static void __iomem *gpio_reg(struct gpio_chip *chip, unsigned offset,
@@ -104,11 +106,18 @@ static int lnw_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 	u32 value;
 	unsigned long flags;
 
+	if (lnw->pdev)
+		pm_runtime_get(&lnw->pdev->dev);
+
 	spin_lock_irqsave(&lnw->lock, flags);
 	value = readl(gpdr);
 	value &= ~BIT(offset % 32);
 	writel(value, gpdr);
 	spin_unlock_irqrestore(&lnw->lock, flags);
+
+	if (lnw->pdev)
+		pm_runtime_put(&lnw->pdev->dev);
+
 	return 0;
 }
 
@@ -120,11 +129,19 @@ static int lnw_gpio_direction_output(struct gpio_chip *chip,
 	unsigned long flags;
 
 	lnw_gpio_set(chip, offset, value);
+
+	if (lnw->pdev)
+		pm_runtime_get(&lnw->pdev->dev);
+
 	spin_lock_irqsave(&lnw->lock, flags);
 	value = readl(gpdr);
 	value |= BIT(offset % 32);
 	writel(value, gpdr);
 	spin_unlock_irqrestore(&lnw->lock, flags);
+
+	if (lnw->pdev)
+		pm_runtime_put(&lnw->pdev->dev);
+
 	return 0;
 }
 
@@ -145,6 +162,10 @@ static int lnw_irq_type(struct irq_data *d, unsigned type)
 
 	if (gpio >= lnw->chip.ngpio)
 		return -EINVAL;
+
+	if (lnw->pdev)
+		pm_runtime_get(&lnw->pdev->dev);
+
 	spin_lock_irqsave(&lnw->lock, flags);
 	if (type & IRQ_TYPE_EDGE_RISING)
 		value = readl(grer) | BIT(gpio % 32);
@@ -159,6 +180,9 @@ static int lnw_irq_type(struct irq_data *d, unsigned type)
 	writel(value, gfer);
 	spin_unlock_irqrestore(&lnw->lock, flags);
 
+	if (lnw->pdev)
+		pm_runtime_put(&lnw->pdev->dev);
+
 	return 0;
 }
 
@@ -211,6 +235,39 @@ static void lnw_irq_handler(unsigned irq, struct irq_desc *desc)
 	chip->irq_eoi(data);
 }
 
+#ifdef CONFIG_PM
+static int lnw_gpio_runtime_resume(struct device *dev)
+{
+	return 0;
+}
+
+static int lnw_gpio_runtime_suspend(struct device *dev)
+{
+	return 0;
+}
+
+static int lnw_gpio_runtime_idle(struct device *dev)
+{
+	int err = pm_schedule_suspend(dev, 500);
+
+	if (!err)
+		return 0;
+
+	return -EBUSY;
+}
+
+#else
+#define lnw_gpio_runtime_suspend	NULL
+#define lnw_gpio_runtime_resume		NULL
+#define lnw_gpio_runtime_idle		NULL
+#endif
+
+static const struct dev_pm_ops lnw_gpio_pm_ops = {
+	.runtime_suspend = lnw_gpio_runtime_suspend,
+	.runtime_resume = lnw_gpio_runtime_resume,
+	.runtime_idle = lnw_gpio_runtime_idle,
+};
+
 static int __devinit lnw_gpio_probe(struct pci_dev *pdev,
 			const struct pci_device_id *id)
 {
@@ -270,6 +327,7 @@ static int __devinit lnw_gpio_probe(struct pci_dev *pdev,
 	lnw->chip.base = gpio_base;
 	lnw->chip.ngpio = id->driver_data;
 	lnw->chip.can_sleep = 0;
+	lnw->pdev = pdev;
 	pci_set_drvdata(pdev, lnw);
 	retval = gpiochip_add(&lnw->chip);
 	if (retval) {
@@ -285,6 +343,10 @@ static int __devinit lnw_gpio_probe(struct pci_dev *pdev,
 	}
 
 	spin_lock_init(&lnw->lock);
+
+	pm_runtime_put_noidle(&pdev->dev);
+	pm_runtime_allow(&pdev->dev);
+
 	goto done;
 err5:
 	kfree(lnw);
@@ -302,6 +364,9 @@ static struct pci_driver lnw_gpio_driver = {
 	.name		= "langwell_gpio",
 	.id_table	= lnw_gpio_ids,
 	.probe		= lnw_gpio_probe,
+	.driver		= {
+		.pm	= &lnw_gpio_pm_ops,
+	},
 };
 
 

drivers/gpio/pch_gpio.c

@@ -283,8 +283,10 @@ static int pch_gpio_resume(struct pci_dev *pdev)
 #define pch_gpio_resume NULL
 #endif
 
+#define PCI_VENDOR_ID_ROHM             0x10DB
 static DEFINE_PCI_DEVICE_TABLE(pch_gpio_pcidev_id) = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8803) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8014) },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, pch_gpio_pcidev_id);

include/asm-generic/gpio.h

@@ -35,9 +35,9 @@
  * platform data and other tables.
  */
 
-static inline int gpio_is_valid(int number)
+static inline bool gpio_is_valid(int number)
 {
-	return ((unsigned)number) < ARCH_NR_GPIOS;
+	return number >= 0 && number < ARCH_NR_GPIOS;
 }
 
 struct device;
@@ -193,8 +193,8 @@ struct gpio {
 };
 
 extern int gpio_request_one(unsigned gpio, unsigned long flags, const char *label);
-extern int gpio_request_array(struct gpio *array, size_t num);
-extern void gpio_free_array(struct gpio *array, size_t num);
+extern int gpio_request_array(const struct gpio *array, size_t num);
+extern void gpio_free_array(const struct gpio *array, size_t num);
 
 #ifdef CONFIG_GPIO_SYSFS
 
@@ -212,7 +212,7 @@ extern void gpio_unexport(unsigned gpio);
 
 #else	/* !CONFIG_GPIOLIB */
 
-static inline int gpio_is_valid(int number)
+static inline bool gpio_is_valid(int number)
 {
 	/* only non-negative numbers are valid */
 	return number >= 0;

include/linux/gpio.h

@@ -25,9 +25,9 @@ struct gpio_chip;
  * warning when something is wrongly called.
  */
 
-static inline int gpio_is_valid(int number)
+static inline bool gpio_is_valid(int number)
 {
-	return 0;
+	return false;
 }
 
 static inline int gpio_request(unsigned gpio, const char *label)
@@ -41,7 +41,7 @@ static inline int gpio_request_one(unsigned gpio,
 	return -ENOSYS;
 }
 
-static inline int gpio_request_array(struct gpio *array, size_t num)
+static inline int gpio_request_array(const struct gpio *array, size_t num)
 {
 	return -ENOSYS;
 }
@@ -54,7 +54,7 @@ static inline void gpio_free(unsigned gpio)
 	WARN_ON(1);
 }
 
-static inline void gpio_free_array(struct gpio *array, size_t num)
+static inline void gpio_free_array(const struct gpio *array, size_t num)
 {
 	might_sleep();