clocksource: sunxi: Cleanup the timer code

The timer code was not exact to some aspects, since most of this code
was written wihout any datasheet. Make the needed corrections to match
the datasheet.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

drivers/clocksource/sunxi_timer.c

@@ -25,15 +25,15 @@
 #include <linux/sunxi_timer.h>
 #include <linux/clk/sunxi.h>
 
-#define TIMER_CTL_REG		0x00
-#define TIMER_CTL_ENABLE		(1 << 0)
+#define TIMER_IRQ_EN_REG	0x00
+#define TIMER_IRQ_EN(val)		(1 << val)
 #define TIMER_IRQ_ST_REG	0x04
-#define TIMER0_CTL_REG		0x10
-#define TIMER0_CTL_ENABLE		(1 << 0)
-#define TIMER0_CTL_AUTORELOAD		(1 << 1)
-#define TIMER0_CTL_ONESHOT		(1 << 7)
-#define TIMER0_INTVAL_REG	0x14
-#define TIMER0_CNTVAL_REG	0x18
+#define TIMER_CTL_REG(val)	(0x10 * val + 0x10)
+#define TIMER_CTL_ENABLE		(1 << 0)
+#define TIMER_CTL_AUTORELOAD		(1 << 1)
+#define TIMER_CTL_ONESHOT		(1 << 7)
+#define TIMER_INTVAL_REG(val)	(0x10 * val + 0x14)
+#define TIMER_CNTVAL_REG(val)	(0x10 * val + 0x18)
 
 #define TIMER_SCAL		16
 
@@ -42,21 +42,21 @@ static void __iomem *timer_base;
 static void sunxi_clkevt_mode(enum clock_event_mode mode,
 			      struct clock_event_device *clk)
 {
-	u32 u = readl(timer_base + TIMER0_CTL_REG);
+	u32 u = readl(timer_base + TIMER_CTL_REG(0));
 
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
-		u &= ~(TIMER0_CTL_ONESHOT);
-		writel(u | TIMER0_CTL_ENABLE, timer_base + TIMER0_CTL_REG);
+		u &= ~(TIMER_CTL_ONESHOT);
+		writel(u | TIMER_CTL_ENABLE, timer_base + TIMER_CTL_REG(0));
 		break;
 
 	case CLOCK_EVT_MODE_ONESHOT:
-		writel(u | TIMER0_CTL_ONESHOT, timer_base + TIMER0_CTL_REG);
+		writel(u | TIMER_CTL_ONESHOT, timer_base + TIMER_CTL_REG(0));
 		break;
 	case CLOCK_EVT_MODE_UNUSED:
 	case CLOCK_EVT_MODE_SHUTDOWN:
 	default:
-		writel(u & ~(TIMER0_CTL_ENABLE), timer_base + TIMER0_CTL_REG);
+		writel(u & ~(TIMER_CTL_ENABLE), timer_base + TIMER_CTL_REG(0));
 		break;
 	}
 }
@@ -64,10 +64,10 @@ static void sunxi_clkevt_mode(enum clock_event_mode mode,
 static int sunxi_clkevt_next_event(unsigned long evt,
 				   struct clock_event_device *unused)
 {
-	u32 u = readl(timer_base + TIMER0_CTL_REG);
-	writel(evt, timer_base + TIMER0_CNTVAL_REG);
-	writel(u | TIMER0_CTL_ENABLE | TIMER0_CTL_AUTORELOAD,
-	       timer_base + TIMER0_CTL_REG);
+	u32 u = readl(timer_base + TIMER_CTL_REG(0));
+	writel(evt, timer_base + TIMER_CNTVAL_REG(0));
+	writel(u | TIMER_CTL_ENABLE | TIMER_CTL_AUTORELOAD,
+	       timer_base + TIMER_CTL_REG(0));
 
 	return 0;
 }
@@ -132,26 +132,26 @@ void __init sunxi_timer_init(void)
 	rate = clk_get_rate(clk);
 
 	writel(rate / (TIMER_SCAL * HZ),
-	       timer_base + TIMER0_INTVAL_REG);
+	       timer_base + TIMER_INTVAL_REG(0));
 
 	/* set clock source to HOSC, 16 pre-division */
-	val = readl(timer_base + TIMER0_CTL_REG);
+	val = readl(timer_base + TIMER_CTL_REG(0));
 	val &= ~(0x07 << 4);
 	val &= ~(0x03 << 2);
 	val |= (4 << 4) | (1 << 2);
-	writel(val, timer_base + TIMER0_CTL_REG);
+	writel(val, timer_base + TIMER_CTL_REG(0));
 
 	/* set mode to auto reload */
-	val = readl(timer_base + TIMER0_CTL_REG);
-	writel(val | TIMER0_CTL_AUTORELOAD, timer_base + TIMER0_CTL_REG);
+	val = readl(timer_base + TIMER_CTL_REG(0));
+	writel(val | TIMER_CTL_AUTORELOAD, timer_base + TIMER_CTL_REG(0));
 
 	ret = setup_irq(irq, &sunxi_timer_irq);
 	if (ret)
 		pr_warn("failed to setup irq %d\n", irq);
 
 	/* Enable timer0 interrupt */
-	val = readl(timer_base + TIMER_CTL_REG);
-	writel(val | TIMER_CTL_ENABLE, timer_base + TIMER_CTL_REG);
+	val = readl(timer_base + TIMER_IRQ_EN_REG);
+	writel(val | TIMER_IRQ_EN(0), timer_base + TIMER_IRQ_EN_REG);
 
 	sunxi_clockevent.cpumask = cpumask_of(0);