sched/deadline: Use the revised wakeup rule for suspending constrained dl tasks
[ Upstream commit 3effcb42 ] We have been facing some problems with self-suspending constrained deadline tasks. The main reason is that the original CBS was not designed for such sort of tasks. One problem reported by Xunlei Pang takes place when a task suspends, and then is awakened before the deadline, but so close to the deadline that its remaining runtime can cause the task to have an absolute density higher than allowed. In such situation, the original CBS assumes that the task is facing an early activation, and so it replenishes the task and set another deadline, one deadline in the future. This rule works fine for implicit deadline tasks. Moreover, it allows the system to adapt the period of a task in which the external event source suffered from a clock drift. However, this opens the window for bandwidth leakage for constrained deadline tasks. For instance, a task with the following parameters: runtime = 5 ms deadline = 7 ms [density] = 5 / 7 = 0.71 period = 1000 ms If the task runs for 1 ms, and then suspends for another 1ms, it will be awakened with the following parameters: remaining runtime = 4 laxity = 5 presenting a absolute density of 4 / 5 = 0.80. In this case, the original CBS would assume the task had an early wakeup. Then, CBS will reset the runtime, and the absolute deadline will be postponed by one relative deadline, allowing the task to run. The problem is that, if the task runs this pattern forever, it will keep receiving bandwidth, being able to run 1ms every 2ms. Following this behavior, the task would be able to run 500 ms in 1 sec. Thus running more than the 5 ms / 1 sec the admission control allowed it to run. Trying to address the self-suspending case, Luca Abeni, Giuseppe Lipari, and Juri Lelli [1] revisited the CBS in order to deal with self-suspending tasks. In the new approach, rather than replenishing/postponing the absolute deadline, the revised wakeup rule adjusts the remaining runtime, reducing it to fit into the allowed density. A revised version of the idea is: At a given time t, the maximum absolute density of a task cannot be higher than its relative density, that is: runtime / (deadline - t) <= dl_runtime / dl_deadline Knowing the laxity of a task (deadline - t), it is possible to move it to the other side of the equality, thus enabling to define max remaining runtime a task can use within the absolute deadline, without over-running the allowed density: runtime = (dl_runtime / dl_deadline) * (deadline - t) For instance, in our previous example, the task could still run: runtime = ( 5 / 7 ) * 5 runtime = 3.57 ms Without causing damage for other deadline tasks. It is note worthy that the laxity cannot be negative because that would cause a negative runtime. Thus, this patch depends on the patch: df8eac8c ("sched/deadline: Throttle a constrained deadline task activated after the deadline") Which throttles a constrained deadline task activated after the deadline. Finally, it is also possible to use the revised wakeup rule for all other tasks, but that would require some more discussions about pros and cons. Reported-by: Xunlei Pang <xpang@redhat.com> Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com> [peterz: replaced dl_is_constrained with dl_is_implicit] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Juri Lelli <juri.lelli@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luca Abeni <luca.abeni@santannapisa.it> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Romulo Silva de Oliveira <romulo.deoliveira@ufsc.br> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tommaso Cucinotta <tommaso.cucinotta@sssup.it> Link: http://lkml.kernel.org/r/5c800ab3a74a168a84ee5f3f84d12a02e11383be.1495803804.git.bristot@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Showing
Please register or sign in to comment