[SERIAL] Convert parport_serial to use new 8250_pci interfaces

Convert parport_serial to use the new 8250_pci interface, converting
the table to a pciserial_board table.  This also unuses the SPCI_*
definitions in serialP.h, which can now be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

drivers/serial/8250_pci.c

@@ -46,7 +46,7 @@ struct pci_serial_quirk {
 	u32	subdevice;
 	int	(*init)(struct pci_dev *dev);
 	int	(*setup)(struct serial_private *, struct pciserial_board *,
-			 struct uart_port *port, int idx);
+			 struct uart_port *, int);
 	void	(*exit)(struct pci_dev *dev);
 };
 
@@ -436,25 +436,6 @@ static int pci_siig_init(struct pci_dev *dev)
 	return -ENODEV;
 }
 
-int pci_siig10x_fn(struct pci_dev *dev, int enable)
-{
-	int ret = 0;
-	if (enable)
-		ret = pci_siig10x_init(dev);
-	return ret;
-}
-
-int pci_siig20x_fn(struct pci_dev *dev, int enable)
-{
-	int ret = 0;
-	if (enable)
-		ret = pci_siig20x_init(dev);
-	return ret;
-}
-
-EXPORT_SYMBOL(pci_siig10x_fn);
-EXPORT_SYMBOL(pci_siig20x_fn);
-
 /*
  * Timedia has an explosion of boards, and to avoid the PCI table from
  * growing *huge*, we use this function to collapse some 70 entries

include/linux/8250_pci.h

@@ -35,6 +35,3 @@ pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
 void pciserial_remove_ports(struct serial_private *priv);
 void pciserial_suspend_ports(struct serial_private *priv);
 void pciserial_resume_ports(struct serial_private *priv);
-
-int pci_siig10x_fn(struct pci_dev *dev, int enable);
-int pci_siig20x_fn(struct pci_dev *dev, int enable);

include/linux/serialP.h

@@ -140,44 +140,4 @@ struct rs_multiport_struct {
 #define ALPHA_KLUDGE_MCR 0
 #endif
 
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK	0x0007
-#define SPCI_FL_BASE0	0x0000
-#define SPCI_FL_BASE1	0x0001
-#define SPCI_FL_BASE2	0x0002
-#define SPCI_FL_BASE3	0x0003
-#define SPCI_FL_BASE4	0x0004
-#define SPCI_FL_GET_BASE(x)	(x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK       (0x0007 << 4)
-#define SPCI_FL_IRQBASE0       (0x0000 << 4)
-#define SPCI_FL_IRQBASE1       (0x0001 << 4)
-#define SPCI_FL_IRQBASE2       (0x0002 << 4)
-#define SPCI_FL_IRQBASE3       (0x0003 << 4)
-#define SPCI_FL_IRQBASE4       (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x)        ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers), 
-   else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE	0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE	0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE	0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP	0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ	0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP		0x2000
-
-#define SPCI_FL_PNPDEFAULT	(SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
 #endif /* _LINUX_SERIAL_H */