Commit 077175f0 authored by Darren Hart's avatar Darren Hart Committed by Greg Kroah-Hartman

pch_uart: Add Fish River Island II uart clock quirks

Add support for the Fish River Island II (FRI2) UART clock following the CM-iTC
quirk handling mechanism. Depending on the firmware installed on the device, the
FRI2 uses a 48MHz or a 64MHz UART clock. This is detected with DMI strings.

Add similar UART clock quirk handling to the pch_console_setup() function to
enable kernel messages on boards with non-standard UART clocks.

Per Alan's suggestion, abstract out UART clock selection into
pch_uart_get_uartclk() to avoid code duplication.
Signed-off-by: default avatarDarren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent a8a3ec9d
......@@ -206,7 +206,10 @@ enum {
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
#define DEFAULT_UARTCLK 1843200 /* 1.8432MHz */
#define DEFAULT_UARTCLK 1843200 /* 1.8432 MHz */
#define CMITC_UARTCLK 192000000 /* 192.0000 MHz */
#define FRI2_64_UARTCLK 64000000 /* 64.0000 MHz */
#define FRI2_48_UARTCLK 48000000 /* 48.0000 MHz */
struct pch_uart_buffer {
unsigned char *buf;
......@@ -364,6 +367,26 @@ static const struct file_operations port_regs_ops = {
};
#endif /* CONFIG_DEBUG_FS */
/* Return UART clock, checking for board specific clocks. */
static int pch_uart_get_uartclk(void)
{
const char *cmp;
cmp = dmi_get_system_info(DMI_BOARD_NAME);
if (cmp && strstr(cmp, "CM-iTC"))
return CMITC_UARTCLK;
cmp = dmi_get_system_info(DMI_BIOS_VERSION);
if (cmp && strnstr(cmp, "FRI2", 4))
return FRI2_64_UARTCLK;
cmp = dmi_get_system_info(DMI_PRODUCT_NAME);
if (cmp && strstr(cmp, "Fish River Island II"))
return FRI2_48_UARTCLK;
return DEFAULT_UARTCLK;
}
static void pch_uart_hal_enable_interrupt(struct eg20t_port *priv,
unsigned int flag)
{
......@@ -1556,8 +1579,7 @@ static int __init pch_console_setup(struct console *co, char *options)
if (!port || (!port->iobase && !port->membase))
return -ENODEV;
/* setup uartclock */
port->uartclk = DEFAULT_UARTCLK;
port->uartclk = pch_uart_get_uartclk();
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
......@@ -1600,10 +1622,9 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
unsigned int iobase;
unsigned int mapbase;
unsigned char *rxbuf;
int fifosize, uartclk;
int fifosize;
int port_type;
struct pch_uart_driver_data *board;
const char *board_name;
char name[32]; /* for debugfs file name */
board = &drv_dat[id->driver_data];
......@@ -1617,13 +1638,6 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
if (!rxbuf)
goto init_port_free_txbuf;
uartclk = DEFAULT_UARTCLK;
/* quirk for CM-iTC board */
board_name = dmi_get_system_info(DMI_BOARD_NAME);
if (board_name && strstr(board_name, "CM-iTC"))
uartclk = 192000000; /* 192.0MHz */
switch (port_type) {
case PORT_UNKNOWN:
fifosize = 256; /* EG20T/ML7213: UART0 */
......@@ -1648,7 +1662,7 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
priv->rxbuf.size = PAGE_SIZE;
priv->fifo_size = fifosize;
priv->uartclk = uartclk;
priv->uartclk = pch_uart_get_uartclk();
priv->port_type = PORT_MAX_8250 + port_type + 1;
priv->port.dev = &pdev->dev;
priv->port.iobase = iobase;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment