tty: serial: Add linflexuart driver for S32V234

Introduce support for LINFlex driver, based on:
- the version of Freescale LPUART driver after commit b3e3bf2e ("Merge
  4.0-rc7 into tty-next");
- commit abf1e0a9 ("tty: serial: fsl_lpuart: lock port on console
  write").
In this basic version, the driver can be tested using initramfs and relies
on the clocks and pin muxing set up by U-Boot.

Remarks concerning the earlycon support:

- LinFlexD does not allow character transmissions in the INIT mode (see
  section 47.4.2.1 in the reference manual[1]). Therefore, a mutual
  exclusion between the first linflex_setup_watermark/linflex_set_termios
  executions and linflex_earlycon_putchar was employed and the characters
  normally sent to earlycon during initialization are kept in a buffer and
  sent afterwards.

- Empirically, character transmission is also forbidden within the last 1-2
  ms before entering the INIT mode, so we use an explicit timeout
  (PREINIT_DELAY) between linflex_earlycon_putchar and the first call to
  linflex_setup_watermark.

- U-Boot currently uses the UART FIFO mode, while this driver makes the
  transition to the buffer mode. Therefore, the earlycon putchar function
  matches the U-Boot behavior before initializations and the Linux behavior
  after.

[1] https://www.nxp.com/webapp/Download?colCode=S32V234RMSigned-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Adrian.Nitu <adrian.nitu@freescale.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Ana Nedelcu <B56683@freescale.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Matthew Nunez <matthew.nunez@nxp.com>
[stefan-gabriel.mirea@nxp.com: Reduced for upstreaming and implemented
                               earlycon support]
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Link: https://lore.kernel.org/r/20190809112853.15846-6-stefan-gabriel.mirea@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/admin-guide/kernel-parameters.txt

@@ -1090,6 +1090,12 @@
 			the framebuffer, pass the 'ram' option so that it is
 			mapped with the correct attributes.
 
+		linflex,<addr>
+			Use early console provided by Freescale LinFlex UART
+			serial driver for NXP S32V234 SoCs. A valid base
+			address must be provided, and the serial port must
+			already be setup and configured.
+
 	earlyprintk=	[X86,SH,ARM,M68k,S390]
 			earlyprintk=vga
 			earlyprintk=sclp

drivers/tty/serial/Kconfig

@@ -1416,6 +1416,21 @@ config SERIAL_FSL_LPUART_CONSOLE
 	  If you have enabled the lpuart serial port on the Freescale SoCs,
 	  you can make it the console by answering Y to this option.
 
+config SERIAL_FSL_LINFLEXUART
+	tristate "Freescale linflexuart serial port support"
+	select SERIAL_CORE
+	help
+	  Support for the on-chip linflexuart on some Freescale SOCs.
+
+config SERIAL_FSL_LINFLEXUART_CONSOLE
+	bool "Console on Freescale linflexuart serial port"
+	depends on SERIAL_FSL_LINFLEXUART=y
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
+	help
+	  If you have enabled the linflexuart serial port on the Freescale
+	  SoCs, you can make it the console by answering Y to this option.
+
 config SERIAL_CONEXANT_DIGICOLOR
 	tristate "Conexant Digicolor CX92xxx USART serial port support"
 	depends on OF

drivers/tty/serial/Makefile

@@ -80,6 +80,7 @@ obj-$(CONFIG_SERIAL_EFM32_UART) += efm32-uart.o
 obj-$(CONFIG_SERIAL_ARC)	+= arc_uart.o
 obj-$(CONFIG_SERIAL_RP2)	+= rp2.o
 obj-$(CONFIG_SERIAL_FSL_LPUART)	+= fsl_lpuart.o
+obj-$(CONFIG_SERIAL_FSL_LINFLEXUART)	+= fsl_linflexuart.o
 obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR)	+= digicolor-usart.o
 obj-$(CONFIG_SERIAL_MEN_Z135)	+= men_z135_uart.o
 obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o

include/uapi/linux/serial_core.h

@@ -290,4 +290,7 @@
 /* Sunix UART */
 #define PORT_SUNIX	121
 
+/* Freescale Linflex UART */
+#define PORT_LINFLEXUART	121
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */