Skip to content

L
linux
Commit 0b80d1ab authored by Stefan Wahren's avatar Stefan Wahren Committed by Shawn Guo
Browse files
Options

ARM: dts: imx28-cfa10036: Convert to use label references 

These Crystal fontz board files still use node name and unit
address to reference parts from the imx28.dtsi . This causes
a lot of redundancy. So use label references in order to make
it easier to maintain.
Signed-off-by: default avatarStefan Wahren <stefan.wahren@i2se.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent d9355d58
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 703 additions and 752 deletions
arch/arm/boot/dts/imx28-cfa10036.dts
View file @ 0b80d1ab
......@@ -16,107 +16,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
ssd1306_cfa10036: ssd1306-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_cfa10036: leds-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
usb0_otg_cfa10036: otg-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_RDY0__USB0_ID
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
reg = <0>;
fsl,pinmux-ids = <
0x31c3 /*
MX28_PAD_PWM3__GPIO_3_28 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
};
ssp0: spi@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
vmmc-supply = <&reg_vddio_sd0>;
bus-width = <4>;
status = "okay";
};
};
apbx@80040000 {
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_b>;
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_b>;
clock-frequency = <400000>;
status = "okay";
ssd1306: oled@3c {
compatible = "solomon,ssd1306fb-i2c";
pinctrl-names = "default";
pinctrl-0 = <&ssd1306_cfa10036>;
reg = <0x3c>;
reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
solomon,height = <32>;
solomon,width = <128>;
solomon,page-offset = <0>;
solomon,com-lrremap;
solomon,com-invdir;
solomon,com-offset = <32>;
};
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
pinctrl-names = "default";
pinctrl-0 = <&usb0_otg_cfa10036>;
dr_mode = "peripheral";
phy_type = "utmi";
status = "okay";
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
......@@ -138,3 +37,95 @@ reg_vddio_sd0: vddio-sd0 {
gpio = <&gpio3 28 0>;
};
};
&duart {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_b>;
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_b>;
clock-frequency = <400000>;
status = "okay";
ssd1306: oled@3c {
compatible = "solomon,ssd1306fb-i2c";
pinctrl-names = "default";
pinctrl-0 = <&ssd1306_cfa10036>;
reg = <0x3c>;
reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
solomon,height = <32>;
solomon,width = <128>;
solomon,page-offset = <0>;
solomon,com-lrremap;
solomon,com-invdir;
solomon,com-offset = <32>;
};
};
&pinctrl {
ssd1306_cfa10036: ssd1306-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_cfa10036: leds-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
usb0_otg_cfa10036: otg-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_RDY0__USB0_ID
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
reg = <0>;
fsl,pinmux-ids = <
0x31c3 /*
MX28_PAD_PWM3__GPIO_3_28 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
};
&ssp0 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
vmmc-supply = <&reg_vddio_sd0>;
bus-width = <4>;
status = "okay";
};
&usb0 {
pinctrl-names = "default";
pinctrl-0 = <&usb0_otg_cfa10036>;
dr_mode = "peripheral";
phy_type = "utmi";
status = "okay";
};
&usbphy0 {
status = "okay";
};
arch/arm/boot/dts/imx28-cfa10049.dts
View file @ 0b80d1ab
This diff is collapsed.
arch/arm/boot/dts/imx28-cfa10055.dts
View file @ 0b80d1ab
......@@ -14,121 +14,6 @@ / {
model = "Crystalfontz CFA-10055 Board";
compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
spi2_pins_cfa10055: spi2-cfa10055@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__GPIO_2_16
MX28_PAD_SSP2_MOSI__GPIO_2_17
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D00__LCD_D0
MX28_PAD_LCD_D01__LCD_D1
MX28_PAD_LCD_D02__LCD_D2
MX28_PAD_LCD_D03__LCD_D3
MX28_PAD_LCD_D04__LCD_D4
MX28_PAD_LCD_D05__LCD_D5
MX28_PAD_LCD_D06__LCD_D6
MX28_PAD_LCD_D07__LCD_D7
MX28_PAD_LCD_D08__LCD_D8
MX28_PAD_LCD_D09__LCD_D9
MX28_PAD_LCD_D10__LCD_D10
MX28_PAD_LCD_D11__LCD_D11
MX28_PAD_LCD_D12__LCD_D12
MX28_PAD_LCD_D13__LCD_D13
MX28_PAD_LCD_D14__LCD_D14
MX28_PAD_LCD_D15__LCD_D15
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_18bit_pins_cfa10055
&lcdif_pins_cfa10055
&lcdif_pins_cfa10055_pullup>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <18>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <9216000>;
hactive = <320>;
vactive = <480>;
hback-porch = <2>;
hfront-porch = <2>;
vback-porch = <2>;
vfront-porch = <2>;
hsync-len = <15>;
vsync-len = <15>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
};
apbx@80040000 {
lradc@80050000 {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pins_b>;
status = "okay";
};
};
};
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
......@@ -159,3 +44,112 @@ backlight {
default-brightness-level = <6>;
};
};
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_18bit_pins_cfa10055
&lcdif_pins_cfa10055
&lcdif_pins_cfa10055_pullup>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <18>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <9216000>;
hactive = <320>;
vactive = <480>;
hback-porch = <2>;
hfront-porch = <2>;
vback-porch = <2>;
vfront-porch = <2>;
hsync-len = <15>;
vsync-len = <15>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
&lradc {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
&pinctrl {
spi2_pins_cfa10055: spi2-cfa10055@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__GPIO_2_16
MX28_PAD_SSP2_MOSI__GPIO_2_17
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D00__LCD_D0
MX28_PAD_LCD_D01__LCD_D1
MX28_PAD_LCD_D02__LCD_D2
MX28_PAD_LCD_D03__LCD_D3
MX28_PAD_LCD_D04__LCD_D4
MX28_PAD_LCD_D05__LCD_D5
MX28_PAD_LCD_D06__LCD_D6
MX28_PAD_LCD_D07__LCD_D7
MX28_PAD_LCD_D08__LCD_D8
MX28_PAD_LCD_D09__LCD_D9
MX28_PAD_LCD_D10__LCD_D10
MX28_PAD_LCD_D11__LCD_D11
MX28_PAD_LCD_D12__LCD_D12
MX28_PAD_LCD_D13__LCD_D13
MX28_PAD_LCD_D14__LCD_D14
MX28_PAD_LCD_D15__LCD_D15
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pins_b>;
status = "okay";
};
arch/arm/boot/dts/imx28-cfa10056.dts
View file @ 0b80d1ab
......@@ -13,81 +13,6 @@ / {
model = "Crystalfontz CFA-10056 Board";
compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
spi2_pins_cfa10056: spi2-cfa10056@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__GPIO_2_16
MX28_PAD_SSP2_MOSI__GPIO_2_17
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_pins_cfa10056: lcdif-10056@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_cfa10056
&lcdif_pins_cfa10056_pullup >;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <32000000>;
hactive = <480>;
vactive = <800>;
hback-porch = <2>;
hfront-porch = <2>;
vback-porch = <2>;
vfront-porch = <2>;
hsync-len = <5>;
vsync-len = <5>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
};
};
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
......@@ -111,3 +36,74 @@ hx8369: hx8369@0 {
};
};
};
&pinctrl {
spi2_pins_cfa10056: spi2-cfa10056@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__GPIO_2_16
MX28_PAD_SSP2_MOSI__GPIO_2_17
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_pins_cfa10056: lcdif-10056@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_cfa10056
&lcdif_pins_cfa10056_pullup >;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <32000000>;
hactive = <480>;
vactive = <800>;
hback-porch = <2>;
hfront-porch = <2>;
vback-porch = <2>;
vfront-porch = <2>;
hsync-len = <5>;
vsync-len = <5>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
arch/arm/boot/dts/imx28-cfa10057.dts
View file @ 0b80d1ab
......@@ -14,126 +14,6 @@ / {
model = "Crystalfontz CFA-10057 Board";
compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
usb_pins_cfa10057: usb-10057@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D00__LCD_D0
MX28_PAD_LCD_D01__LCD_D1
MX28_PAD_LCD_D02__LCD_D2
MX28_PAD_LCD_D03__LCD_D3
MX28_PAD_LCD_D04__LCD_D4
MX28_PAD_LCD_D05__LCD_D5
MX28_PAD_LCD_D06__LCD_D6
MX28_PAD_LCD_D07__LCD_D7
MX28_PAD_LCD_D08__LCD_D8
MX28_PAD_LCD_D09__LCD_D9
MX28_PAD_LCD_D10__LCD_D10
MX28_PAD_LCD_D11__LCD_D11
MX28_PAD_LCD_D12__LCD_D12
MX28_PAD_LCD_D13__LCD_D13
MX28_PAD_LCD_D14__LCD_D14
MX28_PAD_LCD_D15__LCD_D15
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10057: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_18bit_pins_cfa10057
&lcdif_pins_cfa10057>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <18>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <30000000>;
hactive = <480>;
vactive = <800>;
hfront-porch = <12>;
hback-porch = <2>;
vfront-porch = <5>;
vback-porch = <3>;
hsync-len = <2>;
vsync-len = <2>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
};
apbx@80040000 {
lradc@80050000 {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm4_pins_a>;
status = "okay";
};
i2c1: i2c@8005a000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
usbphy1: usbphy@8007e000 {
status = "okay";
};
};
};
ahb@80080000 {
usb1: usb@80090000 {
vbus-supply = <&reg_usb1_vbus>;
pinctrl-0 = <&usb1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
......@@ -151,17 +31,6 @@ reg_usb1_vbus: regulator@0 {
};
};
ahb@80080000 {
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
status = "okay";
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 4 5000000>;
......@@ -169,3 +38,124 @@ backlight {
default-brightness-level = <7>;
};
};
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_18bit_pins_cfa10057
&lcdif_pins_cfa10057>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <18>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <30000000>;
hactive = <480>;
vactive = <800>;
hfront-porch = <12>;
hback-porch = <2>;
vfront-porch = <5>;
vback-porch = <3>;
hsync-len = <2>;
vsync-len = <2>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
&lradc {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&mac0 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
status = "okay";
};
&pinctrl {
usb_pins_cfa10057: usb-10057@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D00__LCD_D0
MX28_PAD_LCD_D01__LCD_D1
MX28_PAD_LCD_D02__LCD_D2
MX28_PAD_LCD_D03__LCD_D3
MX28_PAD_LCD_D04__LCD_D4
MX28_PAD_LCD_D05__LCD_D5
MX28_PAD_LCD_D06__LCD_D6
MX28_PAD_LCD_D07__LCD_D7
MX28_PAD_LCD_D08__LCD_D8
MX28_PAD_LCD_D09__LCD_D9
MX28_PAD_LCD_D10__LCD_D10
MX28_PAD_LCD_D11__LCD_D11
MX28_PAD_LCD_D12__LCD_D12
MX28_PAD_LCD_D13__LCD_D13
MX28_PAD_LCD_D14__LCD_D14
MX28_PAD_LCD_D15__LCD_D15
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10057: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm4_pins_a>;
status = "okay";
};
&usb1 {
vbus-supply = <&reg_usb1_vbus>;
pinctrl-0 = <&usb1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
&usbphy1 {
status = "okay";
};
arch/arm/boot/dts/imx28-cfa10058.dts
View file @ 0b80d1ab
......@@ -14,93 +14,6 @@ / {
model = "Crystalfontz CFA-10058 Board";
compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
usb_pins_cfa10058: usb-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10058: lcdif-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_cfa10058>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <30000000>;
hactive = <800>;
vactive = <480>;
hback-porch = <40>;
hfront-porch = <40>;
vback-porch = <13>;
vfront-porch = <29>;
hsync-len = <8>;
vsync-len = <8>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
};
apbx@80040000 {
lradc@80050000 {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pins_b>;
status = "okay";
};
usbphy1: usbphy@8007e000 {
status = "okay";
};
};
};
ahb@80080000 {
usb1: usb@80090000 {
vbus-supply = <&reg_usb1_vbus>;
pinctrl-0 = <&usb1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
......@@ -118,17 +31,6 @@ reg_usb1_vbus: regulator@0 {
};
};
ahb@80080000 {
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
status = "okay";
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
......@@ -136,3 +38,91 @@ backlight {
default-brightness-level = <6>;
};
};
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_cfa10058>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <30000000>;
hactive = <800>;
vactive = <480>;
hback-porch = <40>;
hfront-porch = <40>;
vback-porch = <13>;
vfront-porch = <29>;
hsync-len = <8>;
vsync-len = <8>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
&lradc {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
&mac0 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
status = "okay";
};
&pinctrl {
usb_pins_cfa10058: usb-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10058: lcdif-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pins_b>;
status = "okay";
};
&usb1 {
vbus-supply = <&reg_usb1_vbus>;
pinctrl-0 = <&usb1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
&usbphy1 {
status = "okay";
};
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7