Commit 0beb5878 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
 "This branch contains device-tree updates for the SPEAr platform.  They
  had dependencies on earlier branches from this merge window, which is
  why they were broken out in a separate branch."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
  ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
  ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
  ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
  ARM: SPEAr1310: Fix AUXDATA for compact flash controller
  ARM: SPEAr13xx: Remove fields not required for ssp controller
  ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
  ARM: SPEAr: DT: Update device nodes
  ARM: SPEAr: DT: add uart state to fix warning
  ARM: SPEAr: DT: Modify DT bindings for STMMAC
  ARM: SPEAr: DT: Fix existing DT support
  ARM: SPEAr: DT: Update partition info for MTD devices
  ARM: SPEAr: DT: Update pinctrl list
  ARM: SPEAr13xx: DT: Add spics gpio controller nodes
parents 6a57d104 eabc5fa5
* SPEAr Shared IRQ layer (shirq)
SPEAr3xx architecture includes shared/multiplexed irqs for certain set
of devices. The multiplexor provides a single interrupt to parent
interrupt controller (VIC) on behalf of a group of devices.
There can be multiple groups available on SPEAr3xx variants but not
exceeding 4. The number of devices in a group can differ, further they
may share same set of status/mask registers spanning across different
bit masks. Also in some cases the group may not have enable or other
registers. This makes software little complex.
A single node in the device tree is used to describe the shared
interrupt multiplexor (one node for all groups). A group in the
interrupt controller shares config/control registers with other groups.
For example, a 32-bit interrupt enable/disable config register can
accommodate upto 4 interrupt groups.
Required properties:
- compatible: should be, either of
- "st,spear300-shirq"
- "st,spear310-shirq"
- "st,spear320-shirq"
- interrupt-controller: Identifies the node as an interrupt controller.
- #interrupt-cells: should be <1> which basically contains the offset
(starting from 0) of interrupts for all the groups.
- reg: Base address and size of shirq registers.
- interrupts: The list of interrupts generated by the groups which are
then connected to a parent interrupt controller. Each group is
associated with one of the interrupts, hence number of interrupts (to
parent) is equal to number of groups. The format of the interrupt
specifier depends in the interrupt parent controller.
Optional properties:
- interrupt-parent: pHandle of the parent interrupt controller, if not
inherited from the parent node.
Example:
The following is an example from the SPEAr320 SoC dtsi file.
shirq: interrupt-controller@0xb3000000 {
compatible = "st,spear320-shirq";
reg = <0xb3000000 0x1000>;
interrupts = <28 29 30 1>;
#interrupt-cells = <1>;
interrupt-controller;
};
...@@ -126,7 +126,8 @@ dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \ ...@@ -126,7 +126,8 @@ dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \
spear1340-evb.dtb spear1340-evb.dtb
dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \ dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \
spear310-evb.dtb \ spear310-evb.dtb \
spear320-evb.dtb spear320-evb.dtb \
spear320-hmi.dtb
dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun4i-cubieboard.dtb \ dtb-$(CONFIG_ARCH_SUNXI) += sun4i-cubieboard.dtb \
sun5i-olinuxino.dtb sun5i-olinuxino.dtb
......
...@@ -30,10 +30,14 @@ pinmux@e0700000 { ...@@ -30,10 +30,14 @@ pinmux@e0700000 {
pinctrl-0 = <&state_default>; pinctrl-0 = <&state_default>;
state_default: pinmux { state_default: pinmux {
i2c0-pmx { i2c0 {
st,pins = "i2c0_grp"; st,pins = "i2c0_grp";
st,function = "i2c0"; st,function = "i2c0";
}; };
i2s0 {
st,pins = "i2s0_grp";
st,function = "i2s0";
};
i2s1 { i2s1 {
st,pins = "i2s1_grp"; st,pins = "i2s1_grp";
st,function = "i2s1"; st,function = "i2s1";
...@@ -42,6 +46,10 @@ gpio { ...@@ -42,6 +46,10 @@ gpio {
st,pins = "arm_gpio_grp"; st,pins = "arm_gpio_grp";
st,function = "arm_gpio"; st,function = "arm_gpio";
}; };
clcd {
st,pins = "clcd_grp" , "clcd_high_res";
st,function = "clcd";
};
eth { eth {
st,pins = "gmii_grp"; st,pins = "gmii_grp";
st,function = "gmii"; st,function = "gmii";
...@@ -74,11 +82,6 @@ i2c1_2 { ...@@ -74,11 +82,6 @@ i2c1_2 {
st,pins = "i2c_1_2_grp"; st,pins = "i2c_1_2_grp";
st,function = "i2c_1_2"; st,function = "i2c_1_2";
}; };
pci {
st,pins = "pcie0_grp","pcie1_grp",
"pcie2_grp";
st,function = "pci";
};
smii { smii {
st,pins = "smii_0_1_2_grp"; st,pins = "smii_0_1_2_grp";
st,function = "smii_0_1_2"; st,function = "smii_0_1_2";
...@@ -88,6 +91,14 @@ nand { ...@@ -88,6 +91,14 @@ nand {
"nand_16bit_grp"; "nand_16bit_grp";
st,function = "nand"; st,function = "nand";
}; };
sata {
st,pins = "sata0_grp";
st,function = "sata";
};
pcie {
st,pins = "pcie1_grp", "pcie2_grp";
st,function = "pci_express";
};
}; };
}; };
...@@ -109,9 +120,49 @@ dma@eb000000 { ...@@ -109,9 +120,49 @@ dma@eb000000 {
fsmc: flash@b0000000 { fsmc: flash@b0000000 {
status = "okay"; status = "okay";
partition@0 {
label = "xloader";
reg = <0x0 0x80000>;
};
partition@80000 {
label = "u-boot";
reg = <0x80000 0x140000>;
};
partition@1C0000 {
label = "environment";
reg = <0x1C0000 0x40000>;
};
partition@200000 {
label = "dtb";
reg = <0x200000 0x40000>;
};
partition@240000 {
label = "linux";
reg = <0x240000 0xC00000>;
};
partition@E40000 {
label = "rootfs";
reg = <0xE40000 0x0>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "wakeup";
linux,code = <0x100>;
gpios = <&gpio0 7 0x4>;
debounce-interval = <20>;
gpio-key,wakeup = <1>;
};
}; };
gmac0: eth@e2000000 { gmac0: eth@e2000000 {
phy-mode = "gmii";
status = "okay"; status = "okay";
}; };
...@@ -135,23 +186,27 @@ partition@0 { ...@@ -135,23 +186,27 @@ partition@0 {
}; };
partition@10000 { partition@10000 {
label = "u-boot"; label = "u-boot";
reg = <0x10000 0x40000>; reg = <0x10000 0x50000>;
};
partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
}; };
partition@50000 { partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
};
partition@80000 {
label = "linux"; label = "linux";
reg = <0x50000 0x2c0000>; reg = <0x80000 0x310000>;
}; };
partition@310000 { partition@390000 {
label = "rootfs"; label = "rootfs";
reg = <0x310000 0x4f0000>; reg = <0x390000 0x0>;
}; };
}; };
}; };
spi0: spi@e0100000 {
status = "okay";
};
ehci@e4800000 { ehci@e4800000 {
status = "okay"; status = "okay";
}; };
...@@ -189,10 +244,6 @@ i2c0: i2c@e0280000 { ...@@ -189,10 +244,6 @@ i2c0: i2c@e0280000 {
status = "okay"; status = "okay";
}; };
i2c1: i2c@5cd00000 {
status = "okay";
};
kbd@e0300000 { kbd@e0300000 {
linux,keymap = < 0x00000001 linux,keymap = < 0x00000001
0x00010002 0x00010002
...@@ -277,6 +328,7 @@ kbd@e0300000 { ...@@ -277,6 +328,7 @@ kbd@e0300000 {
0x08080052 >; 0x08080052 >;
autorepeat; autorepeat;
st,mode = <0>; st,mode = <0>;
suspended_rate = <2000000>;
status = "okay"; status = "okay";
}; };
...@@ -286,6 +338,81 @@ rtc@e0580000 { ...@@ -286,6 +338,81 @@ rtc@e0580000 {
serial@e0000000 { serial@e0000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
};
spi0: spi@e0100000 {
status = "okay";
num-cs = <3>;
cs-gpios = <&gpio1 7 0>, <&spics 0>, <&spics 1>;
stmpe610@0 {
compatible = "st,stmpe610";
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
spi-max-frequency = <1000000>;
spi-cpha;
pl022,hierarchy = <0>;
pl022,interface = <0>;
pl022,slave-tx-disable;
pl022,com-mode = <0>;
pl022,rx-level-trig = <0>;
pl022,tx-level-trig = <0>;
pl022,ctrl-len = <0x7>;
pl022,wait-state = <0>;
pl022,duplex = <0>;
interrupts = <6 0x4>;
interrupt-parent = <&gpio1>;
irq-trigger = <0x2>;
stmpe_touchscreen {
compatible = "st,stmpe-ts";
ts,sample-time = <4>;
ts,mod-12b = <1>;
ts,ref-sel = <0>;
ts,adc-freq = <1>;
ts,ave-ctrl = <1>;
ts,touch-det-delay = <2>;
ts,settling = <2>;
ts,fraction-z = <7>;
ts,i-drive = <1>;
};
};
m25p80@1 {
compatible = "st,m25p80";
reg = <1>;
spi-max-frequency = <12000000>;
spi-cpol;
spi-cpha;
pl022,hierarchy = <0>;
pl022,interface = <0>;
pl022,slave-tx-disable;
pl022,com-mode = <0x2>;
pl022,rx-level-trig = <0>;
pl022,tx-level-trig = <0>;
pl022,ctrl-len = <0x11>;
pl022,wait-state = <0>;
pl022,duplex = <0>;
};
spidev@2 {
compatible = "spidev";
reg = <2>;
spi-max-frequency = <25000000>;
spi-cpha;
pl022,hierarchy = <0>;
pl022,interface = <0>;
pl022,slave-tx-disable;
pl022,com-mode = <0x2>;
pl022,rx-level-trig = <0>;
pl022,tx-level-trig = <0>;
pl022,ctrl-len = <0x11>;
pl022,wait-state = <0>;
pl022,duplex = <0>;
};
}; };
wdt@ec800620 { wdt@ec800620 {
......
...@@ -17,6 +17,18 @@ / { ...@@ -17,6 +17,18 @@ / {
compatible = "st,spear1310"; compatible = "st,spear1310";
ahb { ahb {
spics: spics@e0700000{
compatible = "st,spear-spics-gpio";
reg = <0xe0700000 0x1000>;
st-spics,peripcfg-reg = <0x3b0>;
st-spics,sw-enable-bit = <12>;
st-spics,cs-value-bit = <11>;
st-spics,cs-enable-mask = <3>;
st-spics,cs-enable-shift = <8>;
gpio-controller;
#gpio-cells = <2>;
};
ahci@b1000000 { ahci@b1000000 {
compatible = "snps,spear-ahci"; compatible = "snps,spear-ahci";
reg = <0xb1000000 0x10000>; reg = <0xb1000000 0x10000>;
...@@ -43,6 +55,7 @@ gmac1: eth@5c400000 { ...@@ -43,6 +55,7 @@ gmac1: eth@5c400000 {
reg = <0x5c400000 0x8000>; reg = <0x5c400000 0x8000>;
interrupts = <0 95 0x4>; interrupts = <0 95 0x4>;
interrupt-names = "macirq"; interrupt-names = "macirq";
phy-mode = "mii";
status = "disabled"; status = "disabled";
}; };
...@@ -51,6 +64,7 @@ gmac2: eth@5c500000 { ...@@ -51,6 +64,7 @@ gmac2: eth@5c500000 {
reg = <0x5c500000 0x8000>; reg = <0x5c500000 0x8000>;
interrupts = <0 96 0x4>; interrupts = <0 96 0x4>;
interrupt-names = "macirq"; interrupt-names = "macirq";
phy-mode = "mii";
status = "disabled"; status = "disabled";
}; };
...@@ -59,6 +73,7 @@ gmac3: eth@5c600000 { ...@@ -59,6 +73,7 @@ gmac3: eth@5c600000 {
reg = <0x5c600000 0x8000>; reg = <0x5c600000 0x8000>;
interrupts = <0 97 0x4>; interrupts = <0 97 0x4>;
interrupt-names = "macirq"; interrupt-names = "macirq";
phy-mode = "rmii";
status = "disabled"; status = "disabled";
}; };
...@@ -67,6 +82,7 @@ gmac4: eth@5c700000 { ...@@ -67,6 +82,7 @@ gmac4: eth@5c700000 {
reg = <0x5c700000 0x8000>; reg = <0x5c700000 0x8000>;
interrupts = <0 98 0x4>; interrupts = <0 98 0x4>;
interrupt-names = "macirq"; interrupt-names = "macirq";
phy-mode = "rgmii";
status = "disabled"; status = "disabled";
}; };
...@@ -76,13 +92,6 @@ pinmux: pinmux@e0700000 { ...@@ -76,13 +92,6 @@ pinmux: pinmux@e0700000 {
#gpio-range-cells = <2>; #gpio-range-cells = <2>;
}; };
spi1: spi@5d400000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x5d400000 0x1000>;
interrupts = <0 99 0x4>;
status = "disabled";
};
apb { apb {
i2c1: i2c@5cd00000 { i2c1: i2c@5cd00000 {
#address-cells = <1>; #address-cells = <1>;
...@@ -147,6 +156,15 @@ i2c7: i2c@5d300000 { ...@@ -147,6 +156,15 @@ i2c7: i2c@5d300000 {
status = "disabled"; status = "disabled";
}; };
spi1: spi@5d400000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x5d400000 0x1000>;
interrupts = <0 99 0x4>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
serial@5c800000 { serial@5c800000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0x5c800000 0x1000>; reg = <0x5c800000 0x1000>;
......
...@@ -38,20 +38,15 @@ fsmc { ...@@ -38,20 +38,15 @@ fsmc {
st,pins = "fsmc_8bit_grp"; st,pins = "fsmc_8bit_grp";
st,function = "fsmc"; st,function = "fsmc";
}; };
kbd {
st,pins = "keyboard_row_col_grp",
"keyboard_col5_grp";
st,function = "keyboard";
};
uart0 { uart0 {
st,pins = "uart0_grp", "uart0_enh_grp"; st,pins = "uart0_grp";
st,function = "uart0"; st,function = "uart0";
}; };
i2c0-pmx { i2c0 {
st,pins = "i2c0_grp"; st,pins = "i2c0_grp";
st,function = "i2c0"; st,function = "i2c0";
}; };
i2c1-pmx { i2c1 {
st,pins = "i2c1_grp"; st,pins = "i2c1_grp";
st,function = "i2c1"; st,function = "i2c1";
}; };
...@@ -64,14 +59,9 @@ spdif-out { ...@@ -64,14 +59,9 @@ spdif-out {
st,function = "spdif_out"; st,function = "spdif_out";
}; };
ssp0 { ssp0 {
st,pins = "ssp0_grp", "ssp0_cs1_grp", st,pins = "ssp0_grp", "ssp0_cs1_grp", "ssp0_cs2_grp", "ssp0_cs3_grp";
"ssp0_cs3_grp";
st,function = "ssp0"; st,function = "ssp0";
}; };
pwm {
st,pins = "pwm2_grp", "pwm3_grp";
st,function = "pwm";
};
smi-pmx { smi-pmx {
st,pins = "smi_grp"; st,pins = "smi_grp";
st,function = "smi"; st,function = "smi";
...@@ -84,6 +74,18 @@ gmac { ...@@ -84,6 +74,18 @@ gmac {
st,pins = "gmii_grp", "rgmii_grp"; st,pins = "gmii_grp", "rgmii_grp";
st,function = "gmac"; st,function = "gmac";
}; };
cam0 {
st,pins = "cam0_grp";
st,function = "cam0";
};
cam1 {
st,pins = "cam1_grp";
st,function = "cam1";
};
cam2 {
st,pins = "cam2_grp";
st,function = "cam2";
};
cam3 { cam3 {
st,pins = "cam3_grp"; st,pins = "cam3_grp";
st,function = "cam3"; st,function = "cam3";
...@@ -108,9 +110,18 @@ sata { ...@@ -108,9 +110,18 @@ sata {
st,pins = "sata_grp"; st,pins = "sata_grp";
st,function = "sata"; st,function = "sata";
}; };
pcie {
st,pins = "pcie_grp";
st,function = "pcie";
};
}; };
}; };
ahci@b1000000 {
status = "okay";
};
dma@ea800000 { dma@ea800000 {
status = "okay"; status = "okay";
}; };
...@@ -121,9 +132,35 @@ dma@eb000000 { ...@@ -121,9 +132,35 @@ dma@eb000000 {
fsmc: flash@b0000000 { fsmc: flash@b0000000 {
status = "okay"; status = "okay";
partition@0 {
label = "xloader";
reg = <0x0 0x200000>;
};
partition@200000 {
label = "u-boot";
reg = <0x200000 0x200000>;
};
partition@400000 {
label = "environment";
reg = <0x400000 0x100000>;
};
partition@500000 {
label = "dtb";
reg = <0x500000 0x100000>;
};
partition@600000 {
label = "linux";
reg = <0x600000 0xC00000>;
};
partition@1200000 {
label = "rootfs";
reg = <0x1200000 0x0>;
};
}; };
gmac0: eth@e2000000 { gmac0: eth@e2000000 {
phy-mode = "rgmii";
status = "okay"; status = "okay";
}; };
...@@ -147,31 +184,62 @@ partition@0 { ...@@ -147,31 +184,62 @@ partition@0 {
}; };
partition@10000 { partition@10000 {
label = "u-boot"; label = "u-boot";
reg = <0x10000 0x40000>; reg = <0x10000 0x50000>;
};
partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
}; };
partition@50000 { partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
};
partition@80000 {
label = "linux"; label = "linux";
reg = <0x50000 0x2c0000>; reg = <0x80000 0x310000>;
}; };
partition@310000 { partition@390000 {
label = "rootfs"; label = "rootfs";
reg = <0x310000 0x4f0000>; reg = <0x390000 0x0>;
}; };
}; };
}; };
spi0: spi@e0100000 { ehci@e4800000 {
status = "okay"; status = "okay";
}; };
ehci@e4800000 { gpio_keys {
status = "okay"; compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "wakeup";
linux,code = <0x100>;
gpios = <&gpio1 1 0x4>;
debounce-interval = <20>;
gpio-key,wakeup = <1>;
};
}; };
ehci@e5800000 { ehci@e5800000 {
status = "okay"; status = "okay";
}; };
i2s0: i2s-play@b2400000 {
status = "okay";
};
i2s1: i2s-rec@b2000000 {
status = "okay";
};
incodec: dir-hifi {
compatible = "dummy,dir-hifi";
status = "okay";
};
ohci@e4000000 { ohci@e4000000 {
status = "okay"; status = "okay";
}; };
...@@ -180,11 +248,43 @@ ohci@e5000000 { ...@@ -180,11 +248,43 @@ ohci@e5000000 {
status = "okay"; status = "okay";
}; };
outcodec: dit-hifi {
compatible = "dummy,dit-hifi";
status = "okay";
};
sound {
compatible = "spear,spear-evb";
audio-controllers = <&spdif0 &spdif1 &i2s0 &i2s1>;
audio-codecs = <&incodec &outcodec &sta529 &sta529>;
codec_dai_name = "dir-hifi", "dit-hifi", "sta529-audio", "sta529-audio";
stream_name = "spdif-cap", "spdif-play", "i2s-play", "i2s-cap";
dai_name = "spdifin-pcm", "spdifout-pcm", "i2s0-pcm", "i2s1-pcm";
nr_controllers = <4>;
status = "okay";
};
spdif0: spdif-in@d0100000 {
status = "okay";
};
spdif1: spdif-out@d0000000 {
status = "okay";
};
apb { apb {
adc@e0080000 { adc@e0080000 {
status = "okay"; status = "okay";
}; };
i2s-play@b2400000 {
status = "okay";
};
i2s-rec@b2000000 {
status = "okay";
};
gpio0: gpio@e0600000 { gpio0: gpio@e0600000 {
status = "okay"; status = "okay";
}; };
...@@ -199,10 +299,36 @@ gpio@e2800000 { ...@@ -199,10 +299,36 @@ gpio@e2800000 {
i2c0: i2c@e0280000 { i2c0: i2c@e0280000 {
status = "okay"; status = "okay";
sta529: sta529@1a {
compatible = "st,sta529";
reg = <0x1a>;
};
}; };
i2c1: i2c@b4000000 { i2c1: i2c@b4000000 {
status = "okay"; status = "okay";
eeprom0@56 {
compatible = "st,eeprom";
reg = <0x56>;
};
stmpe801@41 {
compatible = "st,stmpe801";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x41>;
interrupts = <4 0x4>;
interrupt-parent = <&gpio0>;
irq-trigger = <0x2>;
stmpegpio: stmpe_gpio {
compatible = "st,stmpe-gpio";
gpio-controller;
#gpio-cells = <2>;
};
};
}; };
kbd@e0300000 { kbd@e0300000 {
...@@ -289,6 +415,7 @@ kbd@e0300000 { ...@@ -289,6 +415,7 @@ kbd@e0300000 {
0x08080052 >; 0x08080052 >;
autorepeat; autorepeat;
st,mode = <0>; st,mode = <0>;
suspended_rate = <2000000>;
status = "okay"; status = "okay";
}; };
...@@ -298,10 +425,92 @@ rtc@e0580000 { ...@@ -298,10 +425,92 @@ rtc@e0580000 {
serial@e0000000 { serial@e0000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@b4100000 { serial@b4100000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
};
spi0: spi@e0100000 {
status = "okay";
num-cs = <3>;
cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>,
<&gpiopinctrl 85 0>;
m25p80@0 {
compatible = "m25p80";
reg = <0>;
spi-max-frequency = <12000000>;
spi-cpol;
spi-cpha;
pl022,hierarchy = <0>;
pl022,interface = <0>;
pl022,slave-tx-disable;
pl022,com-mode = <0x2>;
pl022,rx-level-trig = <0>;
pl022,tx-level-trig = <0>;
pl022,ctrl-len = <0x11>;
pl022,wait-state = <0>;
pl022,duplex = <0>;
};
stmpe610@1 {
compatible = "st,stmpe610";
spi-max-frequency = <1000000>;
spi-cpha;
reg = <1>;
pl022,hierarchy = <0>;
pl022,interface = <0>;
pl022,slave-tx-disable;
pl022,com-mode = <0>;
pl022,rx-level-trig = <0>;
pl022,tx-level-trig = <0>;
pl022,ctrl-len = <0x7>;
pl022,wait-state = <0>;
pl022,duplex = <0>;
interrupts = <100 0>;
interrupt-parent = <&gpiopinctrl>;
irq-trigger = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
stmpe_touchscreen {
compatible = "st,stmpe-ts";
ts,sample-time = <4>;
ts,mod-12b = <1>;
ts,ref-sel = <0>;
ts,adc-freq = <1>;
ts,ave-ctrl = <1>;
ts,touch-det-delay = <2>;
ts,settling = <2>;
ts,fraction-z = <7>;
ts,i-drive = <1>;
};
};
spidev@2 {
compatible = "spidev";
reg = <2>;
spi-max-frequency = <25000000>;
spi-cpha;
pl022,hierarchy = <0>;
pl022,interface = <0>;
pl022,slave-tx-disable;
pl022,com-mode = <0x2>;
pl022,rx-level-trig = <0>;
pl022,tx-level-trig = <0>;
pl022,ctrl-len = <0x11>;
pl022,wait-state = <0>;
pl022,duplex = <0>;
};
};
timer@ec800600 {
status = "okay";
}; };
wdt@ec800620 { wdt@ec800620 {
......
...@@ -17,6 +17,20 @@ / { ...@@ -17,6 +17,20 @@ / {
compatible = "st,spear1340"; compatible = "st,spear1340";
ahb { ahb {
spics: spics@e0700000{
compatible = "st,spear-spics-gpio";
reg = <0xe0700000 0x1000>;
st-spics,peripcfg-reg = <0x42c>;
st-spics,sw-enable-bit = <21>;
st-spics,cs-value-bit = <20>;
st-spics,cs-enable-mask = <3>;
st-spics,cs-enable-shift = <18>;
gpio-controller;
#gpio-cells = <2>;
status = "disabled";
};
ahci@b1000000 { ahci@b1000000 {
compatible = "snps,spear-ahci"; compatible = "snps,spear-ahci";
reg = <0xb1000000 0x10000>; reg = <0xb1000000 0x10000>;
...@@ -24,15 +38,61 @@ ahci@b1000000 { ...@@ -24,15 +38,61 @@ ahci@b1000000 {
status = "disabled"; status = "disabled";
}; };
i2s-play@b2400000 {
compatible = "snps,designware-i2s";
reg = <0xb2400000 0x10000>;
interrupt-names = "play_irq";
interrupts = <0 98 0x4
0 99 0x4>;
play;
channel = <8>;
status = "disabled";
};
i2s-rec@b2000000 {
compatible = "snps,designware-i2s";
reg = <0xb2000000 0x10000>;
interrupt-names = "record_irq";
interrupts = <0 100 0x4
0 101 0x4>;
record;
channel = <8>;
status = "disabled";
};
pinmux: pinmux@e0700000 { pinmux: pinmux@e0700000 {
compatible = "st,spear1340-pinmux"; compatible = "st,spear1340-pinmux";
reg = <0xe0700000 0x1000>; reg = <0xe0700000 0x1000>;
#gpio-range-cells = <2>; #gpio-range-cells = <2>;
}; };
pwm: pwm@e0180000 {
compatible ="st,spear13xx-pwm";
reg = <0xe0180000 0x1000>;
#pwm-cells = <2>;
status = "disabled";
};
spdif-in@d0100000 {
compatible = "st,spdif-in";
reg = < 0xd0100000 0x20000
0xd0110000 0x10000 >;
interrupts = <0 84 0x4>;
status = "disabled";
};
spdif-out@d0000000 {
compatible = "st,spdif-out";
reg = <0xd0000000 0x20000>;
interrupts = <0 85 0x4>;
status = "disabled";
};
spi1: spi@5d400000 { spi1: spi@5d400000 {
compatible = "arm,pl022", "arm,primecell"; compatible = "arm,pl022", "arm,primecell";
reg = <0x5d400000 0x1000>; reg = <0x5d400000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 99 0x4>; interrupts = <0 99 0x4>;
status = "disabled"; status = "disabled";
}; };
...@@ -44,6 +104,7 @@ i2c1: i2c@b4000000 { ...@@ -44,6 +104,7 @@ i2c1: i2c@b4000000 {
compatible = "snps,designware-i2c"; compatible = "snps,designware-i2c";
reg = <0xb4000000 0x1000>; reg = <0xb4000000 0x1000>;
interrupts = <0 104 0x4>; interrupts = <0 104 0x4>;
write-16bit;
status = "disabled"; status = "disabled";
}; };
......
...@@ -64,12 +64,26 @@ chosen { ...@@ -64,12 +64,26 @@ chosen {
bootargs = "console=ttyAMA0,115200"; bootargs = "console=ttyAMA0,115200";
}; };
cpufreq {
compatible = "st,cpufreq-spear";
cpufreq_tbl = < 166000
200000
250000
300000
400000
500000
600000 >;
status = "disable";
};
ahb { ahb {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
compatible = "simple-bus"; compatible = "simple-bus";
ranges = <0x50000000 0x50000000 0x10000000 ranges = <0x50000000 0x50000000 0x10000000
0xb0000000 0xb0000000 0x10000000 0xb0000000 0xb0000000 0x10000000
0xd0000000 0xd0000000 0x02000000
0xd8000000 0xd8000000 0x01000000
0xe0000000 0xe0000000 0x10000000>; 0xe0000000 0xe0000000 0x10000000>;
sdhci@b3000000 { sdhci@b3000000 {
...@@ -81,7 +95,7 @@ sdhci@b3000000 { ...@@ -81,7 +95,7 @@ sdhci@b3000000 {
cf@b2800000 { cf@b2800000 {
compatible = "arasan,cf-spear1340"; compatible = "arasan,cf-spear1340";
reg = <0xb2800000 0x100>; reg = <0xb2800000 0x1000>;
interrupts = <0 29 0x4>; interrupts = <0 29 0x4>;
status = "disabled"; status = "disabled";
}; };
...@@ -113,6 +127,7 @@ fsmc: flash@b0000000 { ...@@ -113,6 +127,7 @@ fsmc: flash@b0000000 {
0 23 0x4>; 0 23 0x4>;
st,ale-off = <0x20000>; st,ale-off = <0x20000>;
st,cle-off = <0x10000>; st,cle-off = <0x10000>;
st,mode = <2>;
status = "disabled"; status = "disabled";
}; };
...@@ -125,6 +140,13 @@ gmac0: eth@e2000000 { ...@@ -125,6 +140,13 @@ gmac0: eth@e2000000 {
status = "disabled"; status = "disabled";
}; };
pcm {
compatible = "st,pcm-audio";
#address-cells = <0>;
#size-cells = <0>;
status = "disable";
};
smi: flash@ea000000 { smi: flash@ea000000 {
compatible = "st,spear600-smi"; compatible = "st,spear600-smi";
#address-cells = <1>; #address-cells = <1>;
...@@ -134,17 +156,11 @@ smi: flash@ea000000 { ...@@ -134,17 +156,11 @@ smi: flash@ea000000 {
status = "disabled"; status = "disabled";
}; };
spi0: spi@e0100000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0xe0100000 0x1000>;
interrupts = <0 31 0x4>;
status = "disabled";
};
ehci@e4800000 { ehci@e4800000 {
compatible = "st,spear600-ehci", "usb-ehci"; compatible = "st,spear600-ehci", "usb-ehci";
reg = <0xe4800000 0x1000>; reg = <0xe4800000 0x1000>;
interrupts = <0 64 0x4>; interrupts = <0 64 0x4>;
usbh0_id = <0>;
status = "disabled"; status = "disabled";
}; };
...@@ -152,6 +168,7 @@ ehci@e5800000 { ...@@ -152,6 +168,7 @@ ehci@e5800000 {
compatible = "st,spear600-ehci", "usb-ehci"; compatible = "st,spear600-ehci", "usb-ehci";
reg = <0xe5800000 0x1000>; reg = <0xe5800000 0x1000>;
interrupts = <0 66 0x4>; interrupts = <0 66 0x4>;
usbh1_id = <1>;
status = "disabled"; status = "disabled";
}; };
...@@ -159,6 +176,7 @@ ohci@e4000000 { ...@@ -159,6 +176,7 @@ ohci@e4000000 {
compatible = "st,spear600-ohci", "usb-ohci"; compatible = "st,spear600-ohci", "usb-ohci";
reg = <0xe4000000 0x1000>; reg = <0xe4000000 0x1000>;
interrupts = <0 65 0x4>; interrupts = <0 65 0x4>;
usbh0_id = <0>;
status = "disabled"; status = "disabled";
}; };
...@@ -166,6 +184,7 @@ ohci@e5000000 { ...@@ -166,6 +184,7 @@ ohci@e5000000 {
compatible = "st,spear600-ohci", "usb-ohci"; compatible = "st,spear600-ohci", "usb-ohci";
reg = <0xe5000000 0x1000>; reg = <0xe5000000 0x1000>;
interrupts = <0 67 0x4>; interrupts = <0 67 0x4>;
usbh1_id = <1>;
status = "disabled"; status = "disabled";
}; };
...@@ -175,6 +194,8 @@ apb { ...@@ -175,6 +194,8 @@ apb {
compatible = "simple-bus"; compatible = "simple-bus";
ranges = <0x50000000 0x50000000 0x10000000 ranges = <0x50000000 0x50000000 0x10000000
0xb0000000 0xb0000000 0x10000000 0xb0000000 0xb0000000 0x10000000
0xd0000000 0xd0000000 0x02000000
0xd8000000 0xd8000000 0x01000000
0xe0000000 0xe0000000 0x10000000>; 0xe0000000 0xe0000000 0x10000000>;
gpio0: gpio@e0600000 { gpio0: gpio@e0600000 {
...@@ -215,8 +236,35 @@ i2c0: i2c@e0280000 { ...@@ -215,8 +236,35 @@ i2c0: i2c@e0280000 {
status = "disabled"; status = "disabled";
}; };
i2s@e0180000 {
compatible = "st,designware-i2s";
reg = <0xe0180000 0x1000>;
interrupt-names = "play_irq", "record_irq";
interrupts = <0 10 0x4
0 11 0x4 >;
status = "disabled";
};
i2s@e0200000 {
compatible = "st,designware-i2s";
reg = <0xe0200000 0x1000>;
interrupt-names = "play_irq", "record_irq";
interrupts = <0 26 0x4
0 53 0x4>;
status = "disabled";
};
spi0: spi@e0100000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0xe0100000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 31 0x4>;
status = "disabled";
};
rtc@e0580000 { rtc@e0580000 {
compatible = "st,spear-rtc"; compatible = "st,spear600-rtc";
reg = <0xe0580000 0x1000>; reg = <0xe0580000 0x1000>;
interrupts = <0 36 0x4>; interrupts = <0 36 0x4>;
status = "disabled"; status = "disabled";
...@@ -232,7 +280,7 @@ serial@e0000000 { ...@@ -232,7 +280,7 @@ serial@e0000000 {
adc@e0080000 { adc@e0080000 {
compatible = "st,spear600-adc"; compatible = "st,spear600-adc";
reg = <0xe0080000 0x1000>; reg = <0xe0080000 0x1000>;
interrupts = <0 44 0x4>; interrupts = <0 12 0x4>;
status = "disabled"; status = "disabled";
}; };
...@@ -245,7 +293,8 @@ timer@e0380000 { ...@@ -245,7 +293,8 @@ timer@e0380000 {
timer@ec800600 { timer@ec800600 {
compatible = "arm,cortex-a9-twd-timer"; compatible = "arm,cortex-a9-twd-timer";
reg = <0xec800600 0x20>; reg = <0xec800600 0x20>;
interrupts = <1 13 0x301>; interrupts = <1 13 0x4>;
status = "disabled";
}; };
wdt@ec800620 { wdt@ec800620 {
...@@ -257,6 +306,7 @@ wdt@ec800620 { ...@@ -257,6 +306,7 @@ wdt@ec800620 {
thermal@e07008c4 { thermal@e07008c4 {
compatible = "st,thermal-spear1340"; compatible = "st,thermal-spear1340";
reg = <0xe07008c4 0x4>; reg = <0xe07008c4 0x4>;
thermal_flags = <0x7000>;
}; };
}; };
}; };
......
...@@ -100,15 +100,23 @@ partition@0 { ...@@ -100,15 +100,23 @@ partition@0 {
}; };
partition@10000 { partition@10000 {
label = "u-boot"; label = "u-boot";
reg = <0x10000 0x40000>; reg = <0x10000 0x50000>;
}; };
partition@50000 { partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
};
partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
};
partition@80000 {
label = "linux"; label = "linux";
reg = <0x50000 0x2c0000>; reg = <0x80000 0x310000>;
}; };
partition@310000 { partition@390000 {
label = "rootfs"; label = "rootfs";
reg = <0x310000 0x4f0000>; reg = <0x390000 0x0>;
}; };
}; };
}; };
...@@ -235,6 +243,8 @@ rtc@fc900000 { ...@@ -235,6 +243,8 @@ rtc@fc900000 {
serial@d0000000 { serial@d0000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
wdt@fc880000 { wdt@fc880000 {
......
...@@ -27,7 +27,7 @@ pinmux@99000000 { ...@@ -27,7 +27,7 @@ pinmux@99000000 {
}; };
clcd@60000000 { clcd@60000000 {
compatible = "arm,clcd-pl110", "arm,primecell"; compatible = "arm,pl110", "arm,primecell";
reg = <0x60000000 0x1000>; reg = <0x60000000 0x1000>;
interrupts = <30>; interrupts = <30>;
status = "disabled"; status = "disabled";
...@@ -52,6 +52,14 @@ sdhci@70000000 { ...@@ -52,6 +52,14 @@ sdhci@70000000 {
status = "disabled"; status = "disabled";
}; };
shirq: interrupt-controller@0x50000000 {
compatible = "st,spear300-shirq";
reg = <0x50000000 0x1000>;
interrupts = <28>;
#interrupt-cells = <1>;
interrupt-controller;
};
apb { apb {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
...@@ -64,12 +72,16 @@ gpio1: gpio@a9000000 { ...@@ -64,12 +72,16 @@ gpio1: gpio@a9000000 {
compatible = "arm,pl061", "arm,primecell"; compatible = "arm,pl061", "arm,primecell";
gpio-controller; gpio-controller;
reg = <0xa9000000 0x1000>; reg = <0xa9000000 0x1000>;
interrupts = <8>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
kbd@a0000000 { kbd@a0000000 {
compatible = "st,spear300-kbd"; compatible = "st,spear300-kbd";
reg = <0xa0000000 0x1000>; reg = <0xa0000000 0x1000>;
interrupts = <7>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
}; };
......
...@@ -114,15 +114,23 @@ partition@0 { ...@@ -114,15 +114,23 @@ partition@0 {
}; };
partition@10000 { partition@10000 {
label = "u-boot"; label = "u-boot";
reg = <0x10000 0x40000>; reg = <0x10000 0x50000>;
}; };
partition@50000 { partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
};
partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
};
partition@80000 {
label = "linux"; label = "linux";
reg = <0x50000 0x2c0000>; reg = <0x80000 0x310000>;
}; };
partition@310000 { partition@390000 {
label = "rootfs"; label = "rootfs";
reg = <0x310000 0x4f0000>; reg = <0x390000 0x0>;
}; };
}; };
}; };
...@@ -158,26 +166,38 @@ rtc@fc900000 { ...@@ -158,26 +166,38 @@ rtc@fc900000 {
serial@d0000000 { serial@d0000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@b2000000 { serial@b2000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@b2080000 { serial@b2080000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@b2100000 { serial@b2100000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@b2180000 { serial@b2180000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@b2200000 { serial@b2200000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
wdt@fc880000 { wdt@fc880000 {
......
...@@ -40,6 +40,14 @@ fsmc: flash@44000000 { ...@@ -40,6 +40,14 @@ fsmc: flash@44000000 {
status = "disabled"; status = "disabled";
}; };
shirq: interrupt-controller@0xb4000000 {
compatible = "st,spear310-shirq";
reg = <0xb4000000 0x1000>;
interrupts = <28 29 30 1>;
#interrupt-cells = <1>;
interrupt-controller;
};
apb { apb {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
...@@ -50,30 +58,40 @@ apb { ...@@ -50,30 +58,40 @@ apb {
serial@b2000000 { serial@b2000000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xb2000000 0x1000>; reg = <0xb2000000 0x1000>;
interrupts = <8>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
serial@b2080000 { serial@b2080000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xb2080000 0x1000>; reg = <0xb2080000 0x1000>;
interrupts = <9>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
serial@b2100000 { serial@b2100000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xb2100000 0x1000>; reg = <0xb2100000 0x1000>;
interrupts = <10>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
serial@b2180000 { serial@b2180000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xb2180000 0x1000>; reg = <0xb2180000 0x1000>;
interrupts = <11>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
serial@b2200000 { serial@b2200000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xb2200000 0x1000>; reg = <0xb2200000 0x1000>;
interrupts = <12>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
......
...@@ -76,20 +76,12 @@ mii2 { ...@@ -76,20 +76,12 @@ mii2 {
st,function = "mii2"; st,function = "mii2";
}; };
pwm0_1 { pwm0_1 {
st,pins = "pwm0_1_pin_14_15_grp"; st,pins = "pwm0_1_pin_37_38_grp";
st,function = "pwm0_1"; st,function = "pwm0_1";
}; };
pwm2 {
st,pins = "pwm2_pin_13_grp";
st,function = "pwm2";
};
}; };
}; };
clcd@90000000 {
status = "okay";
};
dma@fc400000 { dma@fc400000 {
status = "okay"; status = "okay";
}; };
...@@ -103,6 +95,7 @@ gmac: eth@e0800000 { ...@@ -103,6 +95,7 @@ gmac: eth@e0800000 {
}; };
sdhci@70000000 { sdhci@70000000 {
power-gpio = <&gpiopinctrl 61 1>;
status = "okay"; status = "okay";
}; };
...@@ -122,15 +115,23 @@ partition@0 { ...@@ -122,15 +115,23 @@ partition@0 {
}; };
partition@10000 { partition@10000 {
label = "u-boot"; label = "u-boot";
reg = <0x10000 0x40000>; reg = <0x10000 0x50000>;
};
partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
};
partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
}; };
partition@50000 { partition@80000 {
label = "linux"; label = "linux";
reg = <0x50000 0x2c0000>; reg = <0x80000 0x310000>;
}; };
partition@310000 { partition@390000 {
label = "rootfs"; label = "rootfs";
reg = <0x310000 0x4f0000>; reg = <0x390000 0x0>;
}; };
}; };
}; };
...@@ -182,14 +183,20 @@ rtc@fc900000 { ...@@ -182,14 +183,20 @@ rtc@fc900000 {
serial@d0000000 { serial@d0000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@a3000000 { serial@a3000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@a4000000 { serial@a4000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
wdt@fc880000 { wdt@fc880000 {
......
/*
* DTS file for SPEAr320 Evaluation Baord
*
* Copyright 2012 Shiraz Hashim <shiraz.hashim@st.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
/include/ "spear320.dtsi"
/ {
model = "ST SPEAr320 HMI Board";
compatible = "st,spear320-hmi", "st,spear320";
#address-cells = <1>;
#size-cells = <1>;
memory {
reg = <0 0x40000000>;
};
ahb {
pinmux@b3000000 {
st,pinmux-mode = <4>;
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
i2c0 {
st,pins = "i2c0_grp";
st,function = "i2c0";
};
ssp0 {
st,pins = "ssp0_grp";
st,function = "ssp0";
};
uart0 {
st,pins = "uart0_grp";
st,function = "uart0";
};
clcd {
st,pins = "clcd_grp";
st,function = "clcd";
};
fsmc {
st,pins = "fsmc_8bit_grp";
st,function = "fsmc";
};
sdhci {
st,pins = "sdhci_cd_12_grp";
st,function = "sdhci";
};
i2s {
st,pins = "i2s_grp";
st,function = "i2s";
};
uart1 {
st,pins = "uart1_grp";
st,function = "uart1";
};
uart2 {
st,pins = "uart2_grp";
st,function = "uart2";
};
can0 {
st,pins = "can0_grp";
st,function = "can0";
};
can1 {
st,pins = "can1_grp";
st,function = "can1";
};
mii0_1 {
st,pins = "rmii0_1_grp";
st,function = "mii0_1";
};
pwm0_1 {
st,pins = "pwm0_1_pin_37_38_grp";
st,function = "pwm0_1";
};
pwm2 {
st,pins = "pwm2_pin_34_grp";
st,function = "pwm2";
};
};
};
clcd@90000000 {
status = "okay";
};
dma@fc400000 {
status = "okay";
};
ehci@e1800000 {
status = "okay";
};
fsmc: flash@4c000000 {
status = "okay";
partition@0 {
label = "xloader";
reg = <0x0 0x80000>;
};
partition@80000 {
label = "u-boot";
reg = <0x80000 0x140000>;
};
partition@1C0000 {
label = "environment";
reg = <0x1C0000 0x40000>;
};
partition@200000 {
label = "dtb";
reg = <0x200000 0x40000>;
};
partition@240000 {
label = "linux";
reg = <0x240000 0xC00000>;
};
partition@E40000 {
label = "rootfs";
reg = <0xE40000 0x0>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "user button 1";
linux,code = <0x100>;
gpios = <&stmpegpio 3 0x4>;
debounce-interval = <20>;
gpio-key,wakeup = <1>;
};
button@2 {
label = "user button 2";
linux,code = <0x200>;
gpios = <&stmpegpio 2 0x4>;
debounce-interval = <20>;
gpio-key,wakeup = <1>;
};
};
ohci@e1900000 {
status = "okay";
};
ohci@e2100000 {
status = "okay";
};
pwm: pwm@a8000000 {
status = "okay";
};
sdhci@70000000 {
power-gpio = <&gpiopinctrl 50 1>;
power_always_enb;
status = "okay";
};
smi: flash@fc000000 {
status = "okay";
clock-rate=<50000000>;
flash@f8000000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xf8000000 0x800000>;
st,smi-fast-mode;
partition@0 {
label = "xloader";
reg = <0x0 0x10000>;
};
partition@10000 {
label = "u-boot";
reg = <0x10000 0x50000>;
};
partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
};
partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
};
partition@80000 {
label = "linux";
reg = <0x80000 0x310000>;
};
partition@390000 {
label = "rootfs";
reg = <0x390000 0x0>;
};
};
};
spi0: spi@d0100000 {
status = "okay";
};
spi1: spi@a5000000 {
status = "okay";
};
spi2: spi@a6000000 {
status = "okay";
};
usbd@e1100000 {
status = "okay";
};
apb {
gpio0: gpio@fc980000 {
status = "okay";
};
gpio@b3000000 {
status = "okay";
};
i2c0: i2c@d0180000 {
status = "okay";
stmpe811@41 {
compatible = "st,stmpe811";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x41>;
irq-over-gpio;
irq-gpios = <&gpiopinctrl 29 0x4>;
id = <0>;
blocks = <0x5>;
irq-trigger = <0x1>;
stmpegpio: stmpe-gpio {
compatible = "stmpe,gpio";
reg = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio,norequest-mask = <0xF3>;
};
stmpe610-ts {
compatible = "stmpe,ts";
reg = <0>;
ts,sample-time = <4>;
ts,mod-12b = <1>;
ts,ref-sel = <0>;
ts,adc-freq = <1>;
ts,ave-ctrl = <1>;
ts,touch-det-delay = <3>;
ts,settling = <4>;
ts,fraction-z = <7>;
ts,i-drive = <1>;
};
};
};
i2c1: i2c@a7000000 {
status = "okay";
};
rtc@fc900000 {
status = "okay";
};
serial@d0000000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
};
serial@a3000000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
};
serial@a4000000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
};
wdt@fc880000 {
status = "okay";
};
};
};
};
...@@ -28,9 +28,10 @@ pinmux: pinmux@b3000000 { ...@@ -28,9 +28,10 @@ pinmux: pinmux@b3000000 {
}; };
clcd@90000000 { clcd@90000000 {
compatible = "arm,clcd-pl110", "arm,primecell"; compatible = "arm,pl110", "arm,primecell";
reg = <0x90000000 0x1000>; reg = <0x90000000 0x1000>;
interrupts = <33>; interrupts = <8>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
...@@ -49,27 +50,51 @@ fsmc: flash@4c000000 { ...@@ -49,27 +50,51 @@ fsmc: flash@4c000000 {
sdhci@70000000 { sdhci@70000000 {
compatible = "st,sdhci-spear"; compatible = "st,sdhci-spear";
reg = <0x70000000 0x100>; reg = <0x70000000 0x100>;
interrupts = <29>; interrupts = <10>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
shirq: interrupt-controller@0xb3000000 {
compatible = "st,spear320-shirq";
reg = <0xb3000000 0x1000>;
interrupts = <30 28 29 1>;
#interrupt-cells = <1>;
interrupt-controller;
};
spi1: spi@a5000000 { spi1: spi@a5000000 {
compatible = "arm,pl022", "arm,primecell"; compatible = "arm,pl022", "arm,primecell";
reg = <0xa5000000 0x1000>; reg = <0xa5000000 0x1000>;
interrupts = <15>;
interrupt-parent = <&shirq>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled"; status = "disabled";
}; };
spi2: spi@a6000000 { spi2: spi@a6000000 {
compatible = "arm,pl022", "arm,primecell"; compatible = "arm,pl022", "arm,primecell";
reg = <0xa6000000 0x1000>; reg = <0xa6000000 0x1000>;
interrupts = <16>;
interrupt-parent = <&shirq>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled"; status = "disabled";
}; };
pwm: pwm@a8000000 {
compatible ="st,spear-pwm";
reg = <0xa8000000 0x1000>;
#pwm-cells = <2>;
status = "disabled";
};
apb { apb {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
compatible = "simple-bus"; compatible = "simple-bus";
ranges = <0xa0000000 0xa0000000 0x10000000 ranges = <0xa0000000 0xa0000000 0x20000000
0xd0000000 0xd0000000 0x30000000>; 0xd0000000 0xd0000000 0x30000000>;
i2c1: i2c@a7000000 { i2c1: i2c@a7000000 {
...@@ -77,18 +102,24 @@ i2c1: i2c@a7000000 { ...@@ -77,18 +102,24 @@ i2c1: i2c@a7000000 {
#size-cells = <0>; #size-cells = <0>;
compatible = "snps,designware-i2c"; compatible = "snps,designware-i2c";
reg = <0xa7000000 0x1000>; reg = <0xa7000000 0x1000>;
interrupts = <21>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
serial@a3000000 { serial@a3000000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xa3000000 0x1000>; reg = <0xa3000000 0x1000>;
interrupts = <13>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
serial@a4000000 { serial@a4000000 {
compatible = "arm,pl011", "arm,primecell"; compatible = "arm,pl011", "arm,primecell";
reg = <0xa4000000 0x1000>; reg = <0xa4000000 0x1000>;
interrupts = <14>;
interrupt-parent = <&shirq>;
status = "disabled"; status = "disabled";
}; };
......
...@@ -53,6 +53,7 @@ gmac: eth@e0800000 { ...@@ -53,6 +53,7 @@ gmac: eth@e0800000 {
reg = <0xe0800000 0x8000>; reg = <0xe0800000 0x8000>;
interrupts = <23 22>; interrupts = <23 22>;
interrupt-names = "macirq", "eth_wake_irq"; interrupt-names = "macirq", "eth_wake_irq";
phy-mode = "mii";
status = "disabled"; status = "disabled";
}; };
...@@ -69,6 +70,8 @@ spi0: spi@d0100000 { ...@@ -69,6 +70,8 @@ spi0: spi@d0100000 {
compatible = "arm,pl022", "arm,primecell"; compatible = "arm,pl022", "arm,primecell";
reg = <0xd0100000 0x1000>; reg = <0xd0100000 0x1000>;
interrupts = <20>; interrupts = <20>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled"; status = "disabled";
}; };
...@@ -120,7 +123,7 @@ i2c0: i2c@d0180000 { ...@@ -120,7 +123,7 @@ i2c0: i2c@d0180000 {
}; };
rtc@fc900000 { rtc@fc900000 {
compatible = "st,spear-rtc"; compatible = "st,spear600-rtc";
reg = <0xfc900000 0x1000>; reg = <0xfc900000 0x1000>;
interrupts = <10>; interrupts = <10>;
status = "disabled"; status = "disabled";
......
...@@ -24,15 +24,35 @@ memory { ...@@ -24,15 +24,35 @@ memory {
}; };
ahb { ahb {
clcd@fc200000 {
status = "okay";
};
dma@fc400000 { dma@fc400000 {
status = "okay"; status = "okay";
}; };
ehci@e1800000 {
status = "okay";
};
ehci@e2000000 {
status = "okay";
};
gmac: ethernet@e0800000 { gmac: ethernet@e0800000 {
phy-mode = "gmii"; phy-mode = "gmii";
status = "okay"; status = "okay";
}; };
ohci@e1900000 {
status = "okay";
};
ohci@e2100000 {
status = "okay";
};
smi: flash@fc000000 { smi: flash@fc000000 {
status = "okay"; status = "okay";
clock-rate=<50000000>; clock-rate=<50000000>;
...@@ -49,15 +69,23 @@ partition@0 { ...@@ -49,15 +69,23 @@ partition@0 {
}; };
partition@10000 { partition@10000 {
label = "u-boot"; label = "u-boot";
reg = <0x10000 0x40000>; reg = <0x10000 0x50000>;
}; };
partition@50000 { partition@60000 {
label = "environment";
reg = <0x60000 0x10000>;
};
partition@70000 {
label = "dtb";
reg = <0x70000 0x10000>;
};
partition@80000 {
label = "linux"; label = "linux";
reg = <0x50000 0x2c0000>; reg = <0x80000 0x310000>;
}; };
partition@310000 { partition@390000 {
label = "rootfs"; label = "rootfs";
reg = <0x310000 0x4f0000>; reg = <0x390000 0x0>;
}; };
}; };
}; };
...@@ -65,10 +93,18 @@ partition@310000 { ...@@ -65,10 +93,18 @@ partition@310000 {
apb { apb {
serial@d0000000 { serial@d0000000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
}; };
serial@d0080000 { serial@d0080000 {
status = "okay"; status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
};
rtc@fc900000 {
status = "okay";
}; };
i2c@d0200000 { i2c@d0200000 {
......
...@@ -45,6 +45,14 @@ vic1: interrupt-controller@f1000000 { ...@@ -45,6 +45,14 @@ vic1: interrupt-controller@f1000000 {
#interrupt-cells = <1>; #interrupt-cells = <1>;
}; };
clcd@fc200000 {
compatible = "arm,pl110", "arm,primecell";
reg = <0xfc200000 0x1000>;
interrupt-parent = <&vic1>;
interrupts = <12>;
status = "disabled";
};
dma@fc400000 { dma@fc400000 {
compatible = "arm,pl080", "arm,primecell"; compatible = "arm,pl080", "arm,primecell";
reg = <0xfc400000 0x1000>; reg = <0xfc400000 0x1000>;
...@@ -59,6 +67,7 @@ gmac: ethernet@e0800000 { ...@@ -59,6 +67,7 @@ gmac: ethernet@e0800000 {
interrupt-parent = <&vic1>; interrupt-parent = <&vic1>;
interrupts = <24 23>; interrupts = <24 23>;
interrupt-names = "macirq", "eth_wake_irq"; interrupt-names = "macirq", "eth_wake_irq";
phy-mode = "gmii";
status = "disabled"; status = "disabled";
}; };
...@@ -178,6 +187,13 @@ i2c@d0200000 { ...@@ -178,6 +187,13 @@ i2c@d0200000 {
status = "disabled"; status = "disabled";
}; };
rtc@fc900000 {
compatible = "st,spear600-rtc";
reg = <0xfc900000 0x1000>;
interrupts = <10>;
status = "disabled";
};
timer@f0000000 { timer@f0000000 {
compatible = "st,spear-timer"; compatible = "st,spear-timer";
reg = <0xf0000000 0x400>; reg = <0xf0000000 0x400>;
......
...@@ -47,14 +47,6 @@ ...@@ -47,14 +47,6 @@
#define DMAC1_BASE UL(0xEB000000) #define DMAC1_BASE UL(0xEB000000)
#define MCIF_CF_BASE UL(0xB2800000) #define MCIF_CF_BASE UL(0xB2800000)
/* Devices present in SPEAr1310 */
#ifdef CONFIG_MACH_SPEAR1310
#define SPEAR1310_RAS_GRP1_BASE UL(0xD8000000)
#define VA_SPEAR1310_RAS_GRP1_BASE UL(0xFA000000)
#define SPEAR1310_RAS_BASE UL(0xD8400000)
#define VA_SPEAR1310_RAS_BASE IOMEM(UL(0xFA400000))
#endif /* CONFIG_MACH_SPEAR1310 */
/* Debug uart for linux, will be used for debug and uncompress messages */ /* Debug uart for linux, will be used for debug and uncompress messages */
#define SPEAR_DBG_UART_BASE UART_BASE #define SPEAR_DBG_UART_BASE UART_BASE
#define VA_SPEAR_DBG_UART_BASE VA_UART_BASE #define VA_SPEAR_DBG_UART_BASE VA_UART_BASE
......
...@@ -15,6 +15,7 @@ ...@@ -15,6 +15,7 @@
#include <linux/amba/pl022.h> #include <linux/amba/pl022.h>
#include <linux/of_platform.h> #include <linux/of_platform.h>
#include <linux/pata_arasan_cf_data.h>
#include <asm/hardware/gic.h> #include <asm/hardware/gic.h>
#include <asm/mach/arch.h> #include <asm/mach/arch.h>
#include <asm/mach/map.h> #include <asm/mach/map.h>
...@@ -27,16 +28,25 @@ ...@@ -27,16 +28,25 @@
#define SPEAR1310_SATA1_BASE UL(0xB1800000) #define SPEAR1310_SATA1_BASE UL(0xB1800000)
#define SPEAR1310_SATA2_BASE UL(0xB4000000) #define SPEAR1310_SATA2_BASE UL(0xB4000000)
#define SPEAR1310_RAS_GRP1_BASE UL(0xD8000000)
#define VA_SPEAR1310_RAS_GRP1_BASE UL(0xFA000000)
#define SPEAR1310_RAS_BASE UL(0xD8400000)
#define VA_SPEAR1310_RAS_BASE IOMEM(UL(0xFA400000))
static struct arasan_cf_pdata cf_pdata = {
.cf_if_clk = CF_IF_CLK_166M,
.quirk = CF_BROKEN_UDMA,
.dma_priv = &cf_dma_priv,
};
/* ssp device registration */ /* ssp device registration */
static struct pl022_ssp_controller ssp1_plat_data = { static struct pl022_ssp_controller ssp1_plat_data = {
.bus_id = 0,
.enable_dma = 0, .enable_dma = 0,
.num_chipselect = 3,
}; };
/* Add SPEAr1310 auxdata to pass platform data */ /* Add SPEAr1310 auxdata to pass platform data */
static struct of_dev_auxdata spear1310_auxdata_lookup[] __initdata = { static struct of_dev_auxdata spear1310_auxdata_lookup[] __initdata = {
OF_DEV_AUXDATA("arasan,cf-spear1340", MCIF_CF_BASE, NULL, &cf_dma_priv), OF_DEV_AUXDATA("arasan,cf-spear1340", MCIF_CF_BASE, NULL, &cf_pdata),
OF_DEV_AUXDATA("snps,dma-spear1340", DMAC0_BASE, NULL, &dmac_plat_data), OF_DEV_AUXDATA("snps,dma-spear1340", DMAC0_BASE, NULL, &dmac_plat_data),
OF_DEV_AUXDATA("snps,dma-spear1340", DMAC1_BASE, NULL, &dmac_plat_data), OF_DEV_AUXDATA("snps,dma-spear1340", DMAC1_BASE, NULL, &dmac_plat_data),
OF_DEV_AUXDATA("arm,pl022", SSP_BASE, NULL, &pl022_plat_data), OF_DEV_AUXDATA("arm,pl022", SSP_BASE, NULL, &pl022_plat_data),
......
...@@ -57,12 +57,10 @@ static struct dw_dma_slave ssp_dma_param[] = { ...@@ -57,12 +57,10 @@ static struct dw_dma_slave ssp_dma_param[] = {
}; };
struct pl022_ssp_controller pl022_plat_data = { struct pl022_ssp_controller pl022_plat_data = {
.bus_id = 0,
.enable_dma = 1, .enable_dma = 1,
.dma_filter = dw_dma_filter, .dma_filter = dw_dma_filter,
.dma_rx_param = &ssp_dma_param[1], .dma_rx_param = &ssp_dma_param[1],
.dma_tx_param = &ssp_dma_param[0], .dma_tx_param = &ssp_dma_param[0],
.num_chipselect = 3,
}; };
/* CF device registration */ /* CF device registration */
......
...@@ -14,14 +14,6 @@ ...@@ -14,14 +14,6 @@
#ifndef __MACH_IRQS_H #ifndef __MACH_IRQS_H
#define __MACH_IRQS_H #define __MACH_IRQS_H
/* FIXME: probe all these from DT */ #define NR_IRQS 256
#define SPEAR3XX_IRQ_INTRCOMM_RAS_ARM 1
#define SPEAR3XX_IRQ_GEN_RAS_1 28
#define SPEAR3XX_IRQ_GEN_RAS_2 29
#define SPEAR3XX_IRQ_GEN_RAS_3 30
#define SPEAR3XX_IRQ_VIC_END 32
#define SPEAR3XX_VIRQ_START SPEAR3XX_IRQ_VIC_END
#define NR_IRQS 160
#endif /* __MACH_IRQS_H */ #endif /* __MACH_IRQS_H */
...@@ -17,102 +17,9 @@ ...@@ -17,102 +17,9 @@
#include <linux/of_platform.h> #include <linux/of_platform.h>
#include <asm/hardware/vic.h> #include <asm/hardware/vic.h>
#include <asm/mach/arch.h> #include <asm/mach/arch.h>
#include <plat/shirq.h>
#include <mach/generic.h> #include <mach/generic.h>
#include <mach/spear.h> #include <mach/spear.h>
/* Base address of various IPs */
#define SPEAR300_TELECOM_BASE UL(0x50000000)
/* Interrupt registers offsets and masks */
#define SPEAR300_INT_ENB_MASK_REG 0x54
#define SPEAR300_INT_STS_MASK_REG 0x58
#define SPEAR300_IT_PERS_S_IRQ_MASK (1 << 0)
#define SPEAR300_IT_CHANGE_S_IRQ_MASK (1 << 1)
#define SPEAR300_I2S_IRQ_MASK (1 << 2)
#define SPEAR300_TDM_IRQ_MASK (1 << 3)
#define SPEAR300_CAMERA_L_IRQ_MASK (1 << 4)
#define SPEAR300_CAMERA_F_IRQ_MASK (1 << 5)
#define SPEAR300_CAMERA_V_IRQ_MASK (1 << 6)
#define SPEAR300_KEYBOARD_IRQ_MASK (1 << 7)
#define SPEAR300_GPIO1_IRQ_MASK (1 << 8)
#define SPEAR300_SHIRQ_RAS1_MASK 0x1FF
#define SPEAR300_SOC_CONFIG_BASE UL(0x99000000)
/* SPEAr300 Virtual irq definitions */
/* IRQs sharing IRQ_GEN_RAS_1 */
#define SPEAR300_VIRQ_IT_PERS_S (SPEAR3XX_VIRQ_START + 0)
#define SPEAR300_VIRQ_IT_CHANGE_S (SPEAR3XX_VIRQ_START + 1)
#define SPEAR300_VIRQ_I2S (SPEAR3XX_VIRQ_START + 2)
#define SPEAR300_VIRQ_TDM (SPEAR3XX_VIRQ_START + 3)
#define SPEAR300_VIRQ_CAMERA_L (SPEAR3XX_VIRQ_START + 4)
#define SPEAR300_VIRQ_CAMERA_F (SPEAR3XX_VIRQ_START + 5)
#define SPEAR300_VIRQ_CAMERA_V (SPEAR3XX_VIRQ_START + 6)
#define SPEAR300_VIRQ_KEYBOARD (SPEAR3XX_VIRQ_START + 7)
#define SPEAR300_VIRQ_GPIO1 (SPEAR3XX_VIRQ_START + 8)
/* IRQs sharing IRQ_GEN_RAS_3 */
#define SPEAR300_IRQ_CLCD SPEAR3XX_IRQ_GEN_RAS_3
/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
#define SPEAR300_IRQ_SDHCI SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
/* spear3xx shared irq */
static struct shirq_dev_config shirq_ras1_config[] = {
{
.virq = SPEAR300_VIRQ_IT_PERS_S,
.enb_mask = SPEAR300_IT_PERS_S_IRQ_MASK,
.status_mask = SPEAR300_IT_PERS_S_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_IT_CHANGE_S,
.enb_mask = SPEAR300_IT_CHANGE_S_IRQ_MASK,
.status_mask = SPEAR300_IT_CHANGE_S_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_I2S,
.enb_mask = SPEAR300_I2S_IRQ_MASK,
.status_mask = SPEAR300_I2S_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_TDM,
.enb_mask = SPEAR300_TDM_IRQ_MASK,
.status_mask = SPEAR300_TDM_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_CAMERA_L,
.enb_mask = SPEAR300_CAMERA_L_IRQ_MASK,
.status_mask = SPEAR300_CAMERA_L_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_CAMERA_F,
.enb_mask = SPEAR300_CAMERA_F_IRQ_MASK,
.status_mask = SPEAR300_CAMERA_F_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_CAMERA_V,
.enb_mask = SPEAR300_CAMERA_V_IRQ_MASK,
.status_mask = SPEAR300_CAMERA_V_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_KEYBOARD,
.enb_mask = SPEAR300_KEYBOARD_IRQ_MASK,
.status_mask = SPEAR300_KEYBOARD_IRQ_MASK,
}, {
.virq = SPEAR300_VIRQ_GPIO1,
.enb_mask = SPEAR300_GPIO1_IRQ_MASK,
.status_mask = SPEAR300_GPIO1_IRQ_MASK,
},
};
static struct spear_shirq shirq_ras1 = {
.irq = SPEAR3XX_IRQ_GEN_RAS_1,
.dev_config = shirq_ras1_config,
.dev_count = ARRAY_SIZE(shirq_ras1_config),
.regs = {
.enb_reg = SPEAR300_INT_ENB_MASK_REG,
.status_reg = SPEAR300_INT_STS_MASK_REG,
.status_reg_mask = SPEAR300_SHIRQ_RAS1_MASK,
.clear_reg = -1,
},
};
/* DMAC platform data's slave info */ /* DMAC platform data's slave info */
struct pl08x_channel_data spear300_dma_info[] = { struct pl08x_channel_data spear300_dma_info[] = {
{ {
...@@ -285,21 +192,11 @@ static struct of_dev_auxdata spear300_auxdata_lookup[] __initdata = { ...@@ -285,21 +192,11 @@ static struct of_dev_auxdata spear300_auxdata_lookup[] __initdata = {
static void __init spear300_dt_init(void) static void __init spear300_dt_init(void)
{ {
int ret;
pl080_plat_data.slave_channels = spear300_dma_info; pl080_plat_data.slave_channels = spear300_dma_info;
pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear300_dma_info); pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear300_dma_info);
of_platform_populate(NULL, of_default_bus_match_table, of_platform_populate(NULL, of_default_bus_match_table,
spear300_auxdata_lookup, NULL); spear300_auxdata_lookup, NULL);
/* shared irq registration */
shirq_ras1.regs.base = ioremap(SPEAR300_TELECOM_BASE, SZ_4K);
if (shirq_ras1.regs.base) {
ret = spear_shirq_register(&shirq_ras1);
if (ret)
pr_err("Error registering Shared IRQ\n");
}
} }
static const char * const spear300_dt_board_compat[] = { static const char * const spear300_dt_board_compat[] = {
......
...@@ -18,7 +18,6 @@ ...@@ -18,7 +18,6 @@
#include <linux/of_platform.h> #include <linux/of_platform.h>
#include <asm/hardware/vic.h> #include <asm/hardware/vic.h>
#include <asm/mach/arch.h> #include <asm/mach/arch.h>
#include <plat/shirq.h>
#include <mach/generic.h> #include <mach/generic.h>
#include <mach/spear.h> #include <mach/spear.h>
...@@ -27,176 +26,6 @@ ...@@ -27,176 +26,6 @@
#define SPEAR310_UART3_BASE UL(0xB2100000) #define SPEAR310_UART3_BASE UL(0xB2100000)
#define SPEAR310_UART4_BASE UL(0xB2180000) #define SPEAR310_UART4_BASE UL(0xB2180000)
#define SPEAR310_UART5_BASE UL(0xB2200000) #define SPEAR310_UART5_BASE UL(0xB2200000)
#define SPEAR310_SOC_CONFIG_BASE UL(0xB4000000)
/* Interrupt registers offsets and masks */
#define SPEAR310_INT_STS_MASK_REG 0x04
#define SPEAR310_SMII0_IRQ_MASK (1 << 0)
#define SPEAR310_SMII1_IRQ_MASK (1 << 1)
#define SPEAR310_SMII2_IRQ_MASK (1 << 2)
#define SPEAR310_SMII3_IRQ_MASK (1 << 3)
#define SPEAR310_WAKEUP_SMII0_IRQ_MASK (1 << 4)
#define SPEAR310_WAKEUP_SMII1_IRQ_MASK (1 << 5)
#define SPEAR310_WAKEUP_SMII2_IRQ_MASK (1 << 6)
#define SPEAR310_WAKEUP_SMII3_IRQ_MASK (1 << 7)
#define SPEAR310_UART1_IRQ_MASK (1 << 8)
#define SPEAR310_UART2_IRQ_MASK (1 << 9)
#define SPEAR310_UART3_IRQ_MASK (1 << 10)
#define SPEAR310_UART4_IRQ_MASK (1 << 11)
#define SPEAR310_UART5_IRQ_MASK (1 << 12)
#define SPEAR310_EMI_IRQ_MASK (1 << 13)
#define SPEAR310_TDM_HDLC_IRQ_MASK (1 << 14)
#define SPEAR310_RS485_0_IRQ_MASK (1 << 15)
#define SPEAR310_RS485_1_IRQ_MASK (1 << 16)
#define SPEAR310_SHIRQ_RAS1_MASK 0x000FF
#define SPEAR310_SHIRQ_RAS2_MASK 0x01F00
#define SPEAR310_SHIRQ_RAS3_MASK 0x02000
#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK 0x1C000
/* SPEAr310 Virtual irq definitions */
/* IRQs sharing IRQ_GEN_RAS_1 */
#define SPEAR310_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 0)
#define SPEAR310_VIRQ_SMII1 (SPEAR3XX_VIRQ_START + 1)
#define SPEAR310_VIRQ_SMII2 (SPEAR3XX_VIRQ_START + 2)
#define SPEAR310_VIRQ_SMII3 (SPEAR3XX_VIRQ_START + 3)
#define SPEAR310_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 4)
#define SPEAR310_VIRQ_WAKEUP_SMII1 (SPEAR3XX_VIRQ_START + 5)
#define SPEAR310_VIRQ_WAKEUP_SMII2 (SPEAR3XX_VIRQ_START + 6)
#define SPEAR310_VIRQ_WAKEUP_SMII3 (SPEAR3XX_VIRQ_START + 7)
/* IRQs sharing IRQ_GEN_RAS_2 */
#define SPEAR310_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8)
#define SPEAR310_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9)
#define SPEAR310_VIRQ_UART3 (SPEAR3XX_VIRQ_START + 10)
#define SPEAR310_VIRQ_UART4 (SPEAR3XX_VIRQ_START + 11)
#define SPEAR310_VIRQ_UART5 (SPEAR3XX_VIRQ_START + 12)
/* IRQs sharing IRQ_GEN_RAS_3 */
#define SPEAR310_VIRQ_EMI (SPEAR3XX_VIRQ_START + 13)
#define SPEAR310_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 14)
/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
#define SPEAR310_VIRQ_TDM_HDLC (SPEAR3XX_VIRQ_START + 15)
#define SPEAR310_VIRQ_RS485_0 (SPEAR3XX_VIRQ_START + 16)
#define SPEAR310_VIRQ_RS485_1 (SPEAR3XX_VIRQ_START + 17)
/* spear3xx shared irq */
static struct shirq_dev_config shirq_ras1_config[] = {
{
.virq = SPEAR310_VIRQ_SMII0,
.status_mask = SPEAR310_SMII0_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_SMII1,
.status_mask = SPEAR310_SMII1_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_SMII2,
.status_mask = SPEAR310_SMII2_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_SMII3,
.status_mask = SPEAR310_SMII3_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_WAKEUP_SMII0,
.status_mask = SPEAR310_WAKEUP_SMII0_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_WAKEUP_SMII1,
.status_mask = SPEAR310_WAKEUP_SMII1_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_WAKEUP_SMII2,
.status_mask = SPEAR310_WAKEUP_SMII2_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_WAKEUP_SMII3,
.status_mask = SPEAR310_WAKEUP_SMII3_IRQ_MASK,
},
};
static struct spear_shirq shirq_ras1 = {
.irq = SPEAR3XX_IRQ_GEN_RAS_1,
.dev_config = shirq_ras1_config,
.dev_count = ARRAY_SIZE(shirq_ras1_config),
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.status_reg_mask = SPEAR310_SHIRQ_RAS1_MASK,
.clear_reg = -1,
},
};
static struct shirq_dev_config shirq_ras2_config[] = {
{
.virq = SPEAR310_VIRQ_UART1,
.status_mask = SPEAR310_UART1_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_UART2,
.status_mask = SPEAR310_UART2_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_UART3,
.status_mask = SPEAR310_UART3_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_UART4,
.status_mask = SPEAR310_UART4_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_UART5,
.status_mask = SPEAR310_UART5_IRQ_MASK,
},
};
static struct spear_shirq shirq_ras2 = {
.irq = SPEAR3XX_IRQ_GEN_RAS_2,
.dev_config = shirq_ras2_config,
.dev_count = ARRAY_SIZE(shirq_ras2_config),
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.status_reg_mask = SPEAR310_SHIRQ_RAS2_MASK,
.clear_reg = -1,
},
};
static struct shirq_dev_config shirq_ras3_config[] = {
{
.virq = SPEAR310_VIRQ_EMI,
.status_mask = SPEAR310_EMI_IRQ_MASK,
},
};
static struct spear_shirq shirq_ras3 = {
.irq = SPEAR3XX_IRQ_GEN_RAS_3,
.dev_config = shirq_ras3_config,
.dev_count = ARRAY_SIZE(shirq_ras3_config),
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.status_reg_mask = SPEAR310_SHIRQ_RAS3_MASK,
.clear_reg = -1,
},
};
static struct shirq_dev_config shirq_intrcomm_ras_config[] = {
{
.virq = SPEAR310_VIRQ_TDM_HDLC,
.status_mask = SPEAR310_TDM_HDLC_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_RS485_0,
.status_mask = SPEAR310_RS485_0_IRQ_MASK,
}, {
.virq = SPEAR310_VIRQ_RS485_1,
.status_mask = SPEAR310_RS485_1_IRQ_MASK,
},
};
static struct spear_shirq shirq_intrcomm_ras = {
.irq = SPEAR3XX_IRQ_INTRCOMM_RAS_ARM,
.dev_config = shirq_intrcomm_ras_config,
.dev_count = ARRAY_SIZE(shirq_intrcomm_ras_config),
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.status_reg_mask = SPEAR310_SHIRQ_INTRCOMM_RAS_MASK,
.clear_reg = -1,
},
};
/* DMAC platform data's slave info */ /* DMAC platform data's slave info */
struct pl08x_channel_data spear310_dma_info[] = { struct pl08x_channel_data spear310_dma_info[] = {
...@@ -405,42 +234,11 @@ static struct of_dev_auxdata spear310_auxdata_lookup[] __initdata = { ...@@ -405,42 +234,11 @@ static struct of_dev_auxdata spear310_auxdata_lookup[] __initdata = {
static void __init spear310_dt_init(void) static void __init spear310_dt_init(void)
{ {
void __iomem *base;
int ret;
pl080_plat_data.slave_channels = spear310_dma_info; pl080_plat_data.slave_channels = spear310_dma_info;
pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear310_dma_info); pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear310_dma_info);
of_platform_populate(NULL, of_default_bus_match_table, of_platform_populate(NULL, of_default_bus_match_table,
spear310_auxdata_lookup, NULL); spear310_auxdata_lookup, NULL);
/* shared irq registration */
base = ioremap(SPEAR310_SOC_CONFIG_BASE, SZ_4K);
if (base) {
/* shirq 1 */
shirq_ras1.regs.base = base;
ret = spear_shirq_register(&shirq_ras1);
if (ret)
pr_err("Error registering Shared IRQ 1\n");
/* shirq 2 */
shirq_ras2.regs.base = base;
ret = spear_shirq_register(&shirq_ras2);
if (ret)
pr_err("Error registering Shared IRQ 2\n");
/* shirq 3 */
shirq_ras3.regs.base = base;
ret = spear_shirq_register(&shirq_ras3);
if (ret)
pr_err("Error registering Shared IRQ 3\n");
/* shirq 4 */
shirq_intrcomm_ras.regs.base = base;
ret = spear_shirq_register(&shirq_intrcomm_ras);
if (ret)
pr_err("Error registering Shared IRQ 4\n");
}
} }
static const char * const spear310_dt_board_compat[] = { static const char * const spear310_dt_board_compat[] = {
......
...@@ -19,7 +19,6 @@ ...@@ -19,7 +19,6 @@
#include <linux/of_platform.h> #include <linux/of_platform.h>
#include <asm/hardware/vic.h> #include <asm/hardware/vic.h>
#include <asm/mach/arch.h> #include <asm/mach/arch.h>
#include <plat/shirq.h>
#include <mach/generic.h> #include <mach/generic.h>
#include <mach/spear.h> #include <mach/spear.h>
...@@ -28,184 +27,6 @@ ...@@ -28,184 +27,6 @@
#define SPEAR320_SSP0_BASE UL(0xA5000000) #define SPEAR320_SSP0_BASE UL(0xA5000000)
#define SPEAR320_SSP1_BASE UL(0xA6000000) #define SPEAR320_SSP1_BASE UL(0xA6000000)
/* Interrupt registers offsets and masks */
#define SPEAR320_INT_STS_MASK_REG 0x04
#define SPEAR320_INT_CLR_MASK_REG 0x04
#define SPEAR320_INT_ENB_MASK_REG 0x08
#define SPEAR320_GPIO_IRQ_MASK (1 << 0)
#define SPEAR320_I2S_PLAY_IRQ_MASK (1 << 1)
#define SPEAR320_I2S_REC_IRQ_MASK (1 << 2)
#define SPEAR320_EMI_IRQ_MASK (1 << 7)
#define SPEAR320_CLCD_IRQ_MASK (1 << 8)
#define SPEAR320_SPP_IRQ_MASK (1 << 9)
#define SPEAR320_SDHCI_IRQ_MASK (1 << 10)
#define SPEAR320_CAN_U_IRQ_MASK (1 << 11)
#define SPEAR320_CAN_L_IRQ_MASK (1 << 12)
#define SPEAR320_UART1_IRQ_MASK (1 << 13)
#define SPEAR320_UART2_IRQ_MASK (1 << 14)
#define SPEAR320_SSP1_IRQ_MASK (1 << 15)
#define SPEAR320_SSP2_IRQ_MASK (1 << 16)
#define SPEAR320_SMII0_IRQ_MASK (1 << 17)
#define SPEAR320_MII1_SMII1_IRQ_MASK (1 << 18)
#define SPEAR320_WAKEUP_SMII0_IRQ_MASK (1 << 19)
#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK (1 << 20)
#define SPEAR320_I2C1_IRQ_MASK (1 << 21)
#define SPEAR320_SHIRQ_RAS1_MASK 0x000380
#define SPEAR320_SHIRQ_RAS3_MASK 0x000007
#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK 0x3FF800
/* SPEAr320 Virtual irq definitions */
/* IRQs sharing IRQ_GEN_RAS_1 */
#define SPEAR320_VIRQ_EMI (SPEAR3XX_VIRQ_START + 0)
#define SPEAR320_VIRQ_CLCD (SPEAR3XX_VIRQ_START + 1)
#define SPEAR320_VIRQ_SPP (SPEAR3XX_VIRQ_START + 2)
/* IRQs sharing IRQ_GEN_RAS_2 */
#define SPEAR320_IRQ_SDHCI SPEAR3XX_IRQ_GEN_RAS_2
/* IRQs sharing IRQ_GEN_RAS_3 */
#define SPEAR320_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 3)
#define SPEAR320_VIRQ_I2S_PLAY (SPEAR3XX_VIRQ_START + 4)
#define SPEAR320_VIRQ_I2S_REC (SPEAR3XX_VIRQ_START + 5)
/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
#define SPEAR320_VIRQ_CANU (SPEAR3XX_VIRQ_START + 6)
#define SPEAR320_VIRQ_CANL (SPEAR3XX_VIRQ_START + 7)
#define SPEAR320_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8)
#define SPEAR320_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9)
#define SPEAR320_VIRQ_SSP1 (SPEAR3XX_VIRQ_START + 10)
#define SPEAR320_VIRQ_SSP2 (SPEAR3XX_VIRQ_START + 11)
#define SPEAR320_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 12)
#define SPEAR320_VIRQ_MII1_SMII1 (SPEAR3XX_VIRQ_START + 13)
#define SPEAR320_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 14)
#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1 (SPEAR3XX_VIRQ_START + 15)
#define SPEAR320_VIRQ_I2C1 (SPEAR3XX_VIRQ_START + 16)
/* spear3xx shared irq */
static struct shirq_dev_config shirq_ras1_config[] = {
{
.virq = SPEAR320_VIRQ_EMI,
.status_mask = SPEAR320_EMI_IRQ_MASK,
.clear_mask = SPEAR320_EMI_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_CLCD,
.status_mask = SPEAR320_CLCD_IRQ_MASK,
.clear_mask = SPEAR320_CLCD_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_SPP,
.status_mask = SPEAR320_SPP_IRQ_MASK,
.clear_mask = SPEAR320_SPP_IRQ_MASK,
},
};
static struct spear_shirq shirq_ras1 = {
.irq = SPEAR3XX_IRQ_GEN_RAS_1,
.dev_config = shirq_ras1_config,
.dev_count = ARRAY_SIZE(shirq_ras1_config),
.regs = {
.enb_reg = -1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.status_reg_mask = SPEAR320_SHIRQ_RAS1_MASK,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
static struct shirq_dev_config shirq_ras3_config[] = {
{
.virq = SPEAR320_VIRQ_PLGPIO,
.enb_mask = SPEAR320_GPIO_IRQ_MASK,
.status_mask = SPEAR320_GPIO_IRQ_MASK,
.clear_mask = SPEAR320_GPIO_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_I2S_PLAY,
.enb_mask = SPEAR320_I2S_PLAY_IRQ_MASK,
.status_mask = SPEAR320_I2S_PLAY_IRQ_MASK,
.clear_mask = SPEAR320_I2S_PLAY_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_I2S_REC,
.enb_mask = SPEAR320_I2S_REC_IRQ_MASK,
.status_mask = SPEAR320_I2S_REC_IRQ_MASK,
.clear_mask = SPEAR320_I2S_REC_IRQ_MASK,
},
};
static struct spear_shirq shirq_ras3 = {
.irq = SPEAR3XX_IRQ_GEN_RAS_3,
.dev_config = shirq_ras3_config,
.dev_count = ARRAY_SIZE(shirq_ras3_config),
.regs = {
.enb_reg = SPEAR320_INT_ENB_MASK_REG,
.reset_to_enb = 1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.status_reg_mask = SPEAR320_SHIRQ_RAS3_MASK,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
static struct shirq_dev_config shirq_intrcomm_ras_config[] = {
{
.virq = SPEAR320_VIRQ_CANU,
.status_mask = SPEAR320_CAN_U_IRQ_MASK,
.clear_mask = SPEAR320_CAN_U_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_CANL,
.status_mask = SPEAR320_CAN_L_IRQ_MASK,
.clear_mask = SPEAR320_CAN_L_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_UART1,
.status_mask = SPEAR320_UART1_IRQ_MASK,
.clear_mask = SPEAR320_UART1_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_UART2,
.status_mask = SPEAR320_UART2_IRQ_MASK,
.clear_mask = SPEAR320_UART2_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_SSP1,
.status_mask = SPEAR320_SSP1_IRQ_MASK,
.clear_mask = SPEAR320_SSP1_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_SSP2,
.status_mask = SPEAR320_SSP2_IRQ_MASK,
.clear_mask = SPEAR320_SSP2_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_SMII0,
.status_mask = SPEAR320_SMII0_IRQ_MASK,
.clear_mask = SPEAR320_SMII0_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_MII1_SMII1,
.status_mask = SPEAR320_MII1_SMII1_IRQ_MASK,
.clear_mask = SPEAR320_MII1_SMII1_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_WAKEUP_SMII0,
.status_mask = SPEAR320_WAKEUP_SMII0_IRQ_MASK,
.clear_mask = SPEAR320_WAKEUP_SMII0_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_WAKEUP_MII1_SMII1,
.status_mask = SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK,
.clear_mask = SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK,
}, {
.virq = SPEAR320_VIRQ_I2C1,
.status_mask = SPEAR320_I2C1_IRQ_MASK,
.clear_mask = SPEAR320_I2C1_IRQ_MASK,
},
};
static struct spear_shirq shirq_intrcomm_ras = {
.irq = SPEAR3XX_IRQ_INTRCOMM_RAS_ARM,
.dev_config = shirq_intrcomm_ras_config,
.dev_count = ARRAY_SIZE(shirq_intrcomm_ras_config),
.regs = {
.enb_reg = -1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.status_reg_mask = SPEAR320_SHIRQ_INTRCOMM_RAS_MASK,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
/* DMAC platform data's slave info */ /* DMAC platform data's slave info */
struct pl08x_channel_data spear320_dma_info[] = { struct pl08x_channel_data spear320_dma_info[] = {
{ {
...@@ -416,41 +237,17 @@ static struct of_dev_auxdata spear320_auxdata_lookup[] __initdata = { ...@@ -416,41 +237,17 @@ static struct of_dev_auxdata spear320_auxdata_lookup[] __initdata = {
static void __init spear320_dt_init(void) static void __init spear320_dt_init(void)
{ {
void __iomem *base;
int ret;
pl080_plat_data.slave_channels = spear320_dma_info; pl080_plat_data.slave_channels = spear320_dma_info;
pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear320_dma_info); pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear320_dma_info);
of_platform_populate(NULL, of_default_bus_match_table, of_platform_populate(NULL, of_default_bus_match_table,
spear320_auxdata_lookup, NULL); spear320_auxdata_lookup, NULL);
/* shared irq registration */
base = ioremap(SPEAR320_SOC_CONFIG_BASE, SZ_4K);
if (base) {
/* shirq 1 */
shirq_ras1.regs.base = base;
ret = spear_shirq_register(&shirq_ras1);
if (ret)
pr_err("Error registering Shared IRQ 1\n");
/* shirq 3 */
shirq_ras3.regs.base = base;
ret = spear_shirq_register(&shirq_ras3);
if (ret)
pr_err("Error registering Shared IRQ 3\n");
/* shirq 4 */
shirq_intrcomm_ras.regs.base = base;
ret = spear_shirq_register(&shirq_intrcomm_ras);
if (ret)
pr_err("Error registering Shared IRQ 4\n");
}
} }
static const char * const spear320_dt_board_compat[] = { static const char * const spear320_dt_board_compat[] = {
"st,spear320", "st,spear320",
"st,spear320-evb", "st,spear320-evb",
"st,spear320-hmi",
NULL, NULL,
}; };
......
...@@ -15,6 +15,7 @@ ...@@ -15,6 +15,7 @@
#include <linux/amba/pl022.h> #include <linux/amba/pl022.h>
#include <linux/amba/pl08x.h> #include <linux/amba/pl08x.h>
#include <linux/irqchip/spear-shirq.h>
#include <linux/of_irq.h> #include <linux/of_irq.h>
#include <linux/io.h> #include <linux/io.h>
#include <asm/hardware/pl080.h> #include <asm/hardware/pl080.h>
...@@ -121,6 +122,9 @@ struct sys_timer spear3xx_timer = { ...@@ -121,6 +122,9 @@ struct sys_timer spear3xx_timer = {
static const struct of_device_id vic_of_match[] __initconst = { static const struct of_device_id vic_of_match[] __initconst = {
{ .compatible = "arm,pl190-vic", .data = vic_of_init, }, { .compatible = "arm,pl190-vic", .data = vic_of_init, },
{ .compatible = "st,spear300-shirq", .data = spear300_shirq_of_init, },
{ .compatible = "st,spear310-shirq", .data = spear310_shirq_of_init, },
{ .compatible = "st,spear320-shirq", .data = spear320_shirq_of_init, },
{ /* Sentinel */ } { /* Sentinel */ }
}; };
......
...@@ -5,5 +5,5 @@ ...@@ -5,5 +5,5 @@
# Common support # Common support
obj-y := restart.o time.o obj-y := restart.o time.o
obj-$(CONFIG_ARCH_SPEAR3XX) += pl080.o shirq.o obj-$(CONFIG_ARCH_SPEAR3XX) += pl080.o
obj-$(CONFIG_ARCH_SPEAR6XX) += pl080.o obj-$(CONFIG_ARCH_SPEAR6XX) += pl080.o
/*
* arch/arm/plat-spear/shirq.c
*
* SPEAr platform shared irq layer source file
*
* Copyright (C) 2009 ST Microelectronics
* Viresh Kumar <viresh.linux@gmail.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/err.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/spinlock.h>
#include <plat/shirq.h>
struct spear_shirq *shirq;
static DEFINE_SPINLOCK(lock);
static void shirq_irq_mask(struct irq_data *d)
{
struct spear_shirq *shirq = irq_data_get_irq_chip_data(d);
u32 val, id = d->irq - shirq->dev_config[0].virq;
unsigned long flags;
if ((shirq->regs.enb_reg == -1) || shirq->dev_config[id].enb_mask == -1)
return;
spin_lock_irqsave(&lock, flags);
val = readl(shirq->regs.base + shirq->regs.enb_reg);
if (shirq->regs.reset_to_enb)
val |= shirq->dev_config[id].enb_mask;
else
val &= ~(shirq->dev_config[id].enb_mask);
writel(val, shirq->regs.base + shirq->regs.enb_reg);
spin_unlock_irqrestore(&lock, flags);
}
static void shirq_irq_unmask(struct irq_data *d)
{
struct spear_shirq *shirq = irq_data_get_irq_chip_data(d);
u32 val, id = d->irq - shirq->dev_config[0].virq;
unsigned long flags;
if ((shirq->regs.enb_reg == -1) || shirq->dev_config[id].enb_mask == -1)
return;
spin_lock_irqsave(&lock, flags);
val = readl(shirq->regs.base + shirq->regs.enb_reg);
if (shirq->regs.reset_to_enb)
val &= ~(shirq->dev_config[id].enb_mask);
else
val |= shirq->dev_config[id].enb_mask;
writel(val, shirq->regs.base + shirq->regs.enb_reg);
spin_unlock_irqrestore(&lock, flags);
}
static struct irq_chip shirq_chip = {
.name = "spear_shirq",
.irq_ack = shirq_irq_mask,
.irq_mask = shirq_irq_mask,
.irq_unmask = shirq_irq_unmask,
};
static void shirq_handler(unsigned irq, struct irq_desc *desc)
{
u32 i, val, mask;
struct spear_shirq *shirq = irq_get_handler_data(irq);
desc->irq_data.chip->irq_ack(&desc->irq_data);
while ((val = readl(shirq->regs.base + shirq->regs.status_reg) &
shirq->regs.status_reg_mask)) {
for (i = 0; (i < shirq->dev_count) && val; i++) {
if (!(shirq->dev_config[i].status_mask & val))
continue;
generic_handle_irq(shirq->dev_config[i].virq);
/* clear interrupt */
val &= ~shirq->dev_config[i].status_mask;
if ((shirq->regs.clear_reg == -1) ||
shirq->dev_config[i].clear_mask == -1)
continue;
mask = readl(shirq->regs.base + shirq->regs.clear_reg);
if (shirq->regs.reset_to_clear)
mask &= ~shirq->dev_config[i].clear_mask;
else
mask |= shirq->dev_config[i].clear_mask;
writel(mask, shirq->regs.base + shirq->regs.clear_reg);
}
}
desc->irq_data.chip->irq_unmask(&desc->irq_data);
}
int spear_shirq_register(struct spear_shirq *shirq)
{
int i;
if (!shirq || !shirq->dev_config || !shirq->regs.base)
return -EFAULT;
if (!shirq->dev_count)
return -EINVAL;
irq_set_chained_handler(shirq->irq, shirq_handler);
for (i = 0; i < shirq->dev_count; i++) {
irq_set_chip_and_handler(shirq->dev_config[i].virq,
&shirq_chip, handle_simple_irq);
set_irq_flags(shirq->dev_config[i].virq, IRQF_VALID);
irq_set_chip_data(shirq->dev_config[i].virq, shirq);
}
irq_set_handler_data(shirq->irq, shirq);
return 0;
}
...@@ -20,6 +20,7 @@ ...@@ -20,6 +20,7 @@
#include <mach/spear.h> #include <mach/spear.h>
#include "clk.h" #include "clk.h"
#define VA_SPEAR1310_RAS_BASE IOMEM(UL(0xFA400000))
/* PLL related registers and bit values */ /* PLL related registers and bit values */
#define SPEAR1310_PLL_CFG (VA_MISC_BASE + 0x210) #define SPEAR1310_PLL_CFG (VA_MISC_BASE + 0x210)
/* PLL_CFG bit values */ /* PLL_CFG bit values */
......
obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o
obj-$(CONFIG_ARCH_SUNXI) += irq-sunxi.o obj-$(CONFIG_ARCH_SUNXI) += irq-sunxi.o
obj-$(CONFIG_VERSATILE_FPGA_IRQ) += irq-versatile-fpga.o obj-$(CONFIG_VERSATILE_FPGA_IRQ) += irq-versatile-fpga.o
obj-$(CONFIG_ARCH_SPEAR3XX) += spear-shirq.o
/*
* SPEAr platform shared irq layer source file
*
* Copyright (C) 2009-2012 ST Microelectronics
* Viresh Kumar <viresh.linux@gmail.com>
*
* Copyright (C) 2012 ST Microelectronics
* Shiraz Hashim <shiraz.hashim@st.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/err.h>
#include <linux/export.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/irqchip/spear-shirq.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/spinlock.h>
static DEFINE_SPINLOCK(lock);
/* spear300 shared irq registers offsets and masks */
#define SPEAR300_INT_ENB_MASK_REG 0x54
#define SPEAR300_INT_STS_MASK_REG 0x58
static struct spear_shirq spear300_shirq_ras1 = {
.irq_nr = 9,
.irq_bit_off = 0,
.regs = {
.enb_reg = SPEAR300_INT_ENB_MASK_REG,
.status_reg = SPEAR300_INT_STS_MASK_REG,
.clear_reg = -1,
},
};
static struct spear_shirq *spear300_shirq_blocks[] = {
&spear300_shirq_ras1,
};
/* spear310 shared irq registers offsets and masks */
#define SPEAR310_INT_STS_MASK_REG 0x04
static struct spear_shirq spear310_shirq_ras1 = {
.irq_nr = 8,
.irq_bit_off = 0,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.clear_reg = -1,
},
};
static struct spear_shirq spear310_shirq_ras2 = {
.irq_nr = 5,
.irq_bit_off = 8,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.clear_reg = -1,
},
};
static struct spear_shirq spear310_shirq_ras3 = {
.irq_nr = 1,
.irq_bit_off = 13,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.clear_reg = -1,
},
};
static struct spear_shirq spear310_shirq_intrcomm_ras = {
.irq_nr = 3,
.irq_bit_off = 14,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR310_INT_STS_MASK_REG,
.clear_reg = -1,
},
};
static struct spear_shirq *spear310_shirq_blocks[] = {
&spear310_shirq_ras1,
&spear310_shirq_ras2,
&spear310_shirq_ras3,
&spear310_shirq_intrcomm_ras,
};
/* spear320 shared irq registers offsets and masks */
#define SPEAR320_INT_STS_MASK_REG 0x04
#define SPEAR320_INT_CLR_MASK_REG 0x04
#define SPEAR320_INT_ENB_MASK_REG 0x08
static struct spear_shirq spear320_shirq_ras1 = {
.irq_nr = 3,
.irq_bit_off = 7,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
static struct spear_shirq spear320_shirq_ras2 = {
.irq_nr = 1,
.irq_bit_off = 10,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
static struct spear_shirq spear320_shirq_ras3 = {
.irq_nr = 3,
.irq_bit_off = 0,
.invalid_irq = 1,
.regs = {
.enb_reg = SPEAR320_INT_ENB_MASK_REG,
.reset_to_enb = 1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
static struct spear_shirq spear320_shirq_intrcomm_ras = {
.irq_nr = 11,
.irq_bit_off = 11,
.regs = {
.enb_reg = -1,
.status_reg = SPEAR320_INT_STS_MASK_REG,
.clear_reg = SPEAR320_INT_CLR_MASK_REG,
.reset_to_clear = 1,
},
};
static struct spear_shirq *spear320_shirq_blocks[] = {
&spear320_shirq_ras3,
&spear320_shirq_ras1,
&spear320_shirq_ras2,
&spear320_shirq_intrcomm_ras,
};
static void shirq_irq_mask_unmask(struct irq_data *d, bool mask)
{
struct spear_shirq *shirq = irq_data_get_irq_chip_data(d);
u32 val, offset = d->irq - shirq->irq_base;
unsigned long flags;
if (shirq->regs.enb_reg == -1)
return;
spin_lock_irqsave(&lock, flags);
val = readl(shirq->base + shirq->regs.enb_reg);
if (mask ^ shirq->regs.reset_to_enb)
val &= ~(0x1 << shirq->irq_bit_off << offset);
else
val |= 0x1 << shirq->irq_bit_off << offset;
writel(val, shirq->base + shirq->regs.enb_reg);
spin_unlock_irqrestore(&lock, flags);
}
static void shirq_irq_mask(struct irq_data *d)
{
shirq_irq_mask_unmask(d, 1);
}
static void shirq_irq_unmask(struct irq_data *d)
{
shirq_irq_mask_unmask(d, 0);
}
static struct irq_chip shirq_chip = {
.name = "spear-shirq",
.irq_ack = shirq_irq_mask,
.irq_mask = shirq_irq_mask,
.irq_unmask = shirq_irq_unmask,
};
static void shirq_handler(unsigned irq, struct irq_desc *desc)
{
u32 i, j, val, mask, tmp;
struct irq_chip *chip;
struct spear_shirq *shirq = irq_get_handler_data(irq);
chip = irq_get_chip(irq);
chip->irq_ack(&desc->irq_data);
mask = ((0x1 << shirq->irq_nr) - 1) << shirq->irq_bit_off;
while ((val = readl(shirq->base + shirq->regs.status_reg) &
mask)) {
val >>= shirq->irq_bit_off;
for (i = 0, j = 1; i < shirq->irq_nr; i++, j <<= 1) {
if (!(j & val))
continue;
generic_handle_irq(shirq->irq_base + i);
/* clear interrupt */
if (shirq->regs.clear_reg == -1)
continue;
tmp = readl(shirq->base + shirq->regs.clear_reg);
if (shirq->regs.reset_to_clear)
tmp &= ~(j << shirq->irq_bit_off);
else
tmp |= (j << shirq->irq_bit_off);
writel(tmp, shirq->base + shirq->regs.clear_reg);
}
}
chip->irq_unmask(&desc->irq_data);
}
static void __init spear_shirq_register(struct spear_shirq *shirq)
{
int i;
if (shirq->invalid_irq)
return;
irq_set_chained_handler(shirq->irq, shirq_handler);
for (i = 0; i < shirq->irq_nr; i++) {
irq_set_chip_and_handler(shirq->irq_base + i,
&shirq_chip, handle_simple_irq);
set_irq_flags(shirq->irq_base + i, IRQF_VALID);
irq_set_chip_data(shirq->irq_base + i, shirq);
}
irq_set_handler_data(shirq->irq, shirq);
}
static int __init shirq_init(struct spear_shirq **shirq_blocks, int block_nr,
struct device_node *np)
{
int i, irq_base, hwirq = 0, irq_nr = 0;
static struct irq_domain *shirq_domain;
void __iomem *base;
base = of_iomap(np, 0);
if (!base) {
pr_err("%s: failed to map shirq registers\n", __func__);
return -ENXIO;
}
for (i = 0; i < block_nr; i++)
irq_nr += shirq_blocks[i]->irq_nr;
irq_base = irq_alloc_descs(-1, 0, irq_nr, 0);
if (IS_ERR_VALUE(irq_base)) {
pr_err("%s: irq desc alloc failed\n", __func__);
goto err_unmap;
}
shirq_domain = irq_domain_add_legacy(np, irq_nr, irq_base, 0,
&irq_domain_simple_ops, NULL);
if (WARN_ON(!shirq_domain)) {
pr_warn("%s: irq domain init failed\n", __func__);
goto err_free_desc;
}
for (i = 0; i < block_nr; i++) {
shirq_blocks[i]->base = base;
shirq_blocks[i]->irq_base = irq_find_mapping(shirq_domain,
hwirq);
shirq_blocks[i]->irq = irq_of_parse_and_map(np, i);
spear_shirq_register(shirq_blocks[i]);
hwirq += shirq_blocks[i]->irq_nr;
}
return 0;
err_free_desc:
irq_free_descs(irq_base, irq_nr);
err_unmap:
iounmap(base);
return -ENXIO;
}
int __init spear300_shirq_of_init(struct device_node *np,
struct device_node *parent)
{
return shirq_init(spear300_shirq_blocks,
ARRAY_SIZE(spear300_shirq_blocks), np);
}
int __init spear310_shirq_of_init(struct device_node *np,
struct device_node *parent)
{
return shirq_init(spear310_shirq_blocks,
ARRAY_SIZE(spear310_shirq_blocks), np);
}
int __init spear320_shirq_of_init(struct device_node *np,
struct device_node *parent)
{
return shirq_init(spear320_shirq_blocks,
ARRAY_SIZE(spear320_shirq_blocks), np);
}
/* /*
* arch/arm/plat-spear/include/plat/shirq.h
*
* SPEAr platform shared irq layer header file * SPEAr platform shared irq layer header file
* *
* Copyright (C) 2009 ST Microelectronics * Copyright (C) 2009-2012 ST Microelectronics
* Viresh Kumar <viresh.linux@gmail.com> * Viresh Kumar <viresh.linux@gmail.com>
* *
* This file is licensed under the terms of the GNU General Public * This file is licensed under the terms of the GNU General Public
...@@ -11,31 +9,15 @@ ...@@ -11,31 +9,15 @@
* warranty of any kind, whether express or implied. * warranty of any kind, whether express or implied.
*/ */
#ifndef __PLAT_SHIRQ_H #ifndef __SPEAR_SHIRQ_H
#define __PLAT_SHIRQ_H #define __SPEAR_SHIRQ_H
#include <linux/irq.h> #include <linux/irq.h>
#include <linux/types.h> #include <linux/types.h>
/*
* struct shirq_dev_config: shared irq device configuration
*
* virq: virtual irq number of device
* enb_mask: enable mask of device
* status_mask: status mask of device
* clear_mask: clear mask of device
*/
struct shirq_dev_config {
u32 virq;
u32 enb_mask;
u32 status_mask;
u32 clear_mask;
};
/* /*
* struct shirq_regs: shared irq register configuration * struct shirq_regs: shared irq register configuration
* *
* base: base address of shared irq register
* enb_reg: enable register offset * enb_reg: enable register offset
* reset_to_enb: val 1 indicates, we need to clear bit for enabling interrupt * reset_to_enb: val 1 indicates, we need to clear bit for enabling interrupt
* status_reg: status register offset * status_reg: status register offset
...@@ -44,11 +26,9 @@ struct shirq_dev_config { ...@@ -44,11 +26,9 @@ struct shirq_dev_config {
* reset_to_clear: val 1 indicates, we need to clear bit for clearing interrupt * reset_to_clear: val 1 indicates, we need to clear bit for clearing interrupt
*/ */
struct shirq_regs { struct shirq_regs {
void __iomem *base;
u32 enb_reg; u32 enb_reg;
u32 reset_to_enb; u32 reset_to_enb;
u32 status_reg; u32 status_reg;
u32 status_reg_mask;
u32 clear_reg; u32 clear_reg;
u32 reset_to_clear; u32 reset_to_clear;
}; };
...@@ -57,17 +37,28 @@ struct shirq_regs { ...@@ -57,17 +37,28 @@ struct shirq_regs {
* struct spear_shirq: shared irq structure * struct spear_shirq: shared irq structure
* *
* irq: hardware irq number * irq: hardware irq number
* dev_config: array of device config structures which are using "irq" line * irq_base: base irq in linux domain
* dev_count: size of dev_config array * irq_nr: no. of shared interrupts in a particular block
* irq_bit_off: starting bit offset in the status register
* invalid_irq: irq group is currently disabled
* base: base address of shared irq register
* regs: register configuration for shared irq block * regs: register configuration for shared irq block
*/ */
struct spear_shirq { struct spear_shirq {
u32 irq; u32 irq;
struct shirq_dev_config *dev_config; u32 irq_base;
u32 dev_count; u32 irq_nr;
u32 irq_bit_off;
int invalid_irq;
void __iomem *base;
struct shirq_regs regs; struct shirq_regs regs;
}; };
int spear_shirq_register(struct spear_shirq *shirq); int __init spear300_shirq_of_init(struct device_node *np,
struct device_node *parent);
int __init spear310_shirq_of_init(struct device_node *np,
struct device_node *parent);
int __init spear320_shirq_of_init(struct device_node *np,
struct device_node *parent);
#endif /* __PLAT_SHIRQ_H */ #endif /* __SPEAR_SHIRQ_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment