docs: misc-devices/bh1770glc.txt: convert to ReST

- Adjust document title markup;
- use list markups;
- Adjust identations to display properly at ReST output.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/58ba712524318d03b3196bba33cb409472b4807d.1592203650.git.mchehab+huawei@kernel.orgSigned-off-by: Jonathan Corbet <corbet@lwn.net>

Documentation/misc-devices/bh1770glc.txt → Documentation/misc-devices/bh1770glc.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+=======================
 Kernel driver bh1770glc
 =======================
 
 Supported chips:
-ROHM BH1770GLC
-OSRAM SFH7770
+
+- ROHM BH1770GLC
+- OSRAM SFH7770
 
 Data sheet:
 Not freely available
@@ -48,12 +52,16 @@ chip_id
 	RO - shows detected chip type and version
 
 power_state
-	RW - enable / disable chip. Uses counting logic
-	     1 enables the chip
-	     0 disables the chip
+	RW - enable / disable chip
+
+	Uses counting logic
+
+	     - 1 enables the chip
+	     - 0 disables the chip
 
 lux0_input
 	RO - measured lux value
+
 	     sysfs_notify called when threshold interrupt occurs
 
 lux0_sensor_range
@@ -66,16 +74,22 @@ lux0_rate_avail
 	RO - supported measurement rates
 
 lux0_thresh_above_value
-	RW - HI level threshold value. All results above the value
+	RW - HI level threshold value
+
+	     All results above the value
 	     trigs an interrupt. 65535 (i.e. sensor_range) disables the above
 	     interrupt.
 
 lux0_thresh_below_value
-	RW - LO level threshold value. All results below the value
+	RW - LO level threshold value
+
+	     All results below the value
 	     trigs an interrupt. 0 disables the below interrupt.
 
 lux0_calibscale
-	RW - calibration value. Set to neutral value by default.
+	RW - calibration value
+
+	     Set to neutral value by default.
 	     Output results are multiplied with calibscale / calibscale_default
 	     value.
 
@@ -84,32 +98,37 @@ lux0_calibscale_default
 
 prox0_raw
 	RO - measured proximity value
+
 	     sysfs_notify called when threshold interrupt occurs
 
 prox0_sensor_range
 	RO - prox0_raw max value
 
 prox0_raw_en
-	RW - enable / disable proximity - uses counting logic
-	     1 enables the proximity
-	     0 disables the proximity
+	RW - enable / disable proximity
+
+	     Uses counting logic
+
+	     - 1 enables the proximity
+	     - 0 disables the proximity
 
 prox0_thresh_above_count
 	RW - number of proximity interrupts needed before triggering the event
 
 prox0_rate_above
 	RW - Measurement rate (in Hz) when the level is above threshold
-	     i.e. when proximity on has been reported.
+	i.e. when proximity on has been reported.
 
 prox0_rate_below
 	RW - Measurement rate (in Hz) when the level is below threshold
-	     i.e. when proximity off has been reported.
+	i.e. when proximity off has been reported.
 
 prox0_rate_avail
 	RO - Supported proximity measurement rates in Hz
 
 prox0_thresh_above0_value
 	RW - threshold level which trigs proximity events.
+
 	     Filtered by persistence filter (prox0_thresh_above_count)
 
 prox0_thresh_above1_value

Documentation/misc-devices/index.rst

@@ -15,6 +15,7 @@ fit into other categories.
    :maxdepth: 2
 
    ad525x_dpot
+   bh1770glc
    eeprom
    c2port
    ibmvmc