Commit 0fc23d20 authored by Hans de Goede's avatar Hans de Goede Committed by Mauro Carvalho Chehab

V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.

-Make raw bayer header size change from 20 to 16 affect rev072a only, my 2
 rev012a cams both have a header size of 20
-While testing this I also tested the new exposure setting (good work on
 finding the register JF), and after quite a bit of testing have found out the
 exact meaning of the register, this patch modifies setexposure to control
 the exposure over a much wider range.
Signed-off-by: default avatarHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: default avatarJean-Francois Moine <moinejf@free.fr>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@redhat.com>
parent b77c0046
......@@ -38,9 +38,9 @@ struct sd {
#define CONTRAST_MAX 0x3fff
__u16 exposure; /* rev12a only */
#define EXPOSURE_MIN 0
#define EXPOSURE_MIN 1
#define EXPOSURE_DEF 200
#define EXPOSURE_MAX 762
#define EXPOSURE_MAX (4095 - 900) /* see set_exposure */
__u8 brightness; /* rev72a only */
#define BRIGHTNESS_MIN 0
......@@ -648,9 +648,31 @@ static void setexposure(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
int expo;
int clock_divider;
__u8 data[2];
expo = sd->exposure + 0x20a8; /* from test */
/* Register 0x8309 controls exposure for the spca561,
the basic exposure setting goes from 1-2047, where 1 is completely
dark and 2047 is very bright. It not only influences exposure but
also the framerate (to allow for longer exposure) from 1 - 300 it
only raises the exposure time then from 300 - 600 it halves the
framerate to be able to further raise the exposure time and for every
300 more it halves the framerate again. This allows for a maximum
exposure time of circa 0.2 - 0.25 seconds (30 / (2000/3000) fps).
Sometimes this is not enough, the 1-2047 uses bits 0-10, bits 11-12
configure a divider for the base framerate which us used at the
exposure setting of 1-300. These bits configure the base framerate
according to the following formula: fps = 60 / (value + 2) */
if (sd->exposure < 2048) {
expo = sd->exposure;
clock_divider = 0;
} else {
/* Add 900 to make the 0 setting of the second part of the
exposure equal to the 2047 setting of the first part. */
expo = (sd->exposure - 2048) + 900;
clock_divider = 3;
}
expo |= clock_divider << 11;
data[0] = expo;
data[1] = expo >> 8;
reg_w_buf(gspca_dev, 0x8309, data, 2);
......@@ -680,23 +702,11 @@ static void setautogain(struct gspca_dev *gspca_dev)
static void sd_start_12a(struct gspca_dev *gspca_dev)
{
struct usb_device *dev = gspca_dev->dev;
int Clck;
int Clck = 0x8a; /* lower 0x8X values lead to fps > 30 */
__u8 Reg8307[] = { 0xaa, 0x00 };
int mode;
mode = gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv;
switch (mode) {
case 0:
case 1:
Clck = 0x8a;
break;
case 2:
Clck = 0x85;
break;
default:
Clck = 0x83;
break;
}
if (mode <= 1) {
/* Use compression on 320x240 and above */
reg_w_val(dev, 0x8500, 0x10 | mode);
......@@ -714,6 +724,7 @@ static void sd_start_12a(struct gspca_dev *gspca_dev)
setcontrast(gspca_dev);
setwhite(gspca_dev);
setautogain(gspca_dev);
setexposure(gspca_dev);
}
static void sd_start_72a(struct gspca_dev *gspca_dev)
{
......@@ -849,6 +860,8 @@ static void sd_pkt_scan(struct gspca_dev *gspca_dev,
__u8 *data, /* isoc packet */
int len) /* iso packet length */
{
struct sd *sd = (struct sd *) gspca_dev;
switch (data[0]) {
case 0: /* start of frame */
frame = gspca_frame_add(gspca_dev, LAST_PACKET, frame,
......@@ -861,9 +874,13 @@ static void sd_pkt_scan(struct gspca_dev *gspca_dev,
frame, data, len);
} else {
/* raw bayer (with a header, which we skip) */
/*fixme: is this specific to the rev012a? */
data += 16;
len -= 16;
if (sd->chip_revision == Rev012A) {
data += 20;
len -= 20;
} else {
data += 16;
len -= 16;
}
gspca_frame_add(gspca_dev, FIRST_PACKET,
frame, data, len);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment