gpio: pcie-idio-24: Enable PEX8311 interrupts

This enables the PEX8311 internal PCI wire interrupt and the PEX8311
local interrupt input so the local interrupts are forwarded to the PCI.

Fixes: 58556204 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

drivers/gpio/gpio-pcie-idio-24.c

@@ -28,6 +28,47 @@
 #include <linux/spinlock.h>
 #include <linux/types.h>
 
+/*
+ * PLX PEX8311 PCI LCS_INTCSR Interrupt Control/Status
+ *
+ * Bit: Description
+ *   0: Enable Interrupt Sources (Bit 0)
+ *   1: Enable Interrupt Sources (Bit 1)
+ *   2: Generate Internal PCI Bus Internal SERR# Interrupt
+ *   3: Mailbox Interrupt Enable
+ *   4: Power Management Interrupt Enable
+ *   5: Power Management Interrupt
+ *   6: Slave Read Local Data Parity Check Error Enable
+ *   7: Slave Read Local Data Parity Check Error Status
+ *   8: Internal PCI Wire Interrupt Enable
+ *   9: PCI Express Doorbell Interrupt Enable
+ *  10: PCI Abort Interrupt Enable
+ *  11: Local Interrupt Input Enable
+ *  12: Retry Abort Enable
+ *  13: PCI Express Doorbell Interrupt Active
+ *  14: PCI Abort Interrupt Active
+ *  15: Local Interrupt Input Active
+ *  16: Local Interrupt Output Enable
+ *  17: Local Doorbell Interrupt Enable
+ *  18: DMA Channel 0 Interrupt Enable
+ *  19: DMA Channel 1 Interrupt Enable
+ *  20: Local Doorbell Interrupt Active
+ *  21: DMA Channel 0 Interrupt Active
+ *  22: DMA Channel 1 Interrupt Active
+ *  23: Built-In Self-Test (BIST) Interrupt Active
+ *  24: Direct Master was the Bus Master during a Master or Target Abort
+ *  25: DMA Channel 0 was the Bus Master during a Master or Target Abort
+ *  26: DMA Channel 1 was the Bus Master during a Master or Target Abort
+ *  27: Target Abort after internal 256 consecutive Master Retrys
+ *  28: PCI Bus wrote data to LCS_MBOX0
+ *  29: PCI Bus wrote data to LCS_MBOX1
+ *  30: PCI Bus wrote data to LCS_MBOX2
+ *  31: PCI Bus wrote data to LCS_MBOX3
+ */
+#define PLX_PEX8311_PCI_LCS_INTCSR  0x68
+#define INTCSR_INTERNAL_PCI_WIRE    BIT(8)
+#define INTCSR_LOCAL_INPUT          BIT(11)
+
 /**
  * struct idio_24_gpio_reg - GPIO device registers structure
  * @out0_7:	Read: FET Outputs 0-7
@@ -92,6 +133,7 @@ struct idio_24_gpio_reg {
 struct idio_24_gpio {
 	struct gpio_chip chip;
 	raw_spinlock_t lock;
+	__u8 __iomem *plx;
 	struct idio_24_gpio_reg __iomem *reg;
 	unsigned long irq_mask;
 };
@@ -455,6 +497,7 @@ static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	struct device *const dev = &pdev->dev;
 	struct idio_24_gpio *idio24gpio;
 	int err;
+	const size_t pci_plx_bar_index = 1;
 	const size_t pci_bar_index = 2;
 	const char *const name = pci_name(pdev);
 	struct gpio_irq_chip *girq;
@@ -469,12 +512,13 @@ static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		return err;
 	}
 
-	err = pcim_iomap_regions(pdev, BIT(pci_bar_index), name);
+	err = pcim_iomap_regions(pdev, BIT(pci_plx_bar_index) | BIT(pci_bar_index), name);
 	if (err) {
 		dev_err(dev, "Unable to map PCI I/O addresses (%d)\n", err);
 		return err;
 	}
 
+	idio24gpio->plx = pcim_iomap_table(pdev)[pci_plx_bar_index];
 	idio24gpio->reg = pcim_iomap_table(pdev)[pci_bar_index];
 
 	idio24gpio->chip.label = name;
@@ -504,6 +548,12 @@ static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	/* Software board reset */
 	iowrite8(0, &idio24gpio->reg->soft_reset);
+	/*
+	 * enable PLX PEX8311 internal PCI wire interrupt and local interrupt
+	 * input
+	 */
+	iowrite8((INTCSR_INTERNAL_PCI_WIRE | INTCSR_LOCAL_INPUT) >> 8,
+		 idio24gpio->plx + PLX_PEX8311_PCI_LCS_INTCSR + 1);
 
 	err = devm_gpiochip_add_data(dev, &idio24gpio->chip, idio24gpio);
 	if (err) {