arm64: dts: renesas: rzg2l-smarc: Add support for enabling MTU3

Add support for PMOD_MTU3 macro to enable MTU3 node on RZ/{G2,V2}L SMARC
EVK.

The MTU3a PWM pins are muxed with spi1 pins and counter external input
phase clock pins are muxed with scif2 pins. Disable these IPs when
PMOD_MTU3 macro is enabled.

Apart from this, the counter Z phase clock signal is muxed with the
SDHI1 cd signal. So disable SDHI1 IP, when the counter Z phase signal
is enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230706153047.368993-1-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts

@@ -6,6 +6,27 @@
  */
 
 /dts-v1/;
+
+/* Enable SCIF2 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0	1
+
+/*
+ * To enable MTU3a PWM on PMOD0,
+ * Disable PMOD1_SER0 by setting "#define PMOD1_SER0	0" above and
+ * enable PMOD_MTU3 by setting "#define PMOD_MTU3	1" below.
+ */
+#define PMOD_MTU3	0
+
+#if (PMOD_MTU3 && PMOD1_SER0)
+#error "Cannot set as PMOD_MTU3 and PMOD1_SER0 are mutually exclusive "
+#endif
+
+#define MTU3_COUNTER_Z_PHASE_SIGNAL	0
+
+#if (!PMOD_MTU3 && MTU3_COUNTER_Z_PHASE_SIGNAL)
+#error "Cannot set 1 to MTU3_COUNTER_Z_PHASE_SIGNAL as PMOD_MTU3=0"
+#endif
+
 #include "r9a07g044l2.dtsi"
 #include "rzg2l-smarc-som.dtsi"
 #include "rzg2l-smarc-pinfunction.dtsi"

arch/arm64/boot/dts/renesas/r9a07g054l2-smarc.dts

@@ -6,6 +6,26 @@
  */
 
 /dts-v1/;
+
+/* Enable SCIF2 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0	1
+
+/*
+ * To enable MTU3a PWM on PMOD0,
+ * Disable PMOD1_SER0 by setting "#define PMOD1_SER0	0" above and
+ * enable PMOD_MTU3 by setting "#define PMOD_MTU3	1" below.
+ */
+#define PMOD_MTU3	0
+
+#if (PMOD_MTU3 && PMOD1_SER0)
+#error "Cannot set as PMOD_MTU3 and PMOD1_SER0 are mutually exclusive "
+#endif
+
+#define MTU3_COUNTER_Z_PHASE_SIGNAL	0
+#if (!PMOD_MTU3 && MTU3_COUNTER_Z_PHASE_SIGNAL)
+#error "Cannot set 1 to MTU3_COUNTER_Z_PHASE_SIGNAL as PMOD_MTU3=0"
+#endif
+
 #include "r9a07g054l2.dtsi"
 #include "rzg2l-smarc-som.dtsi"
 #include "rzg2l-smarc-pinfunction.dtsi"

arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi

@@ -53,6 +53,26 @@ i2c3_pins: i2c3 {
 			 <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
 	};
 
+	mtu3_pins: mtu3 {
+		mtu3-ext-clk-input-pin {
+			pinmux = <RZG2L_PORT_PINMUX(48, 0, 4)>, /* MTCLKA */
+				 <RZG2L_PORT_PINMUX(48, 1, 4)>; /* MTCLKB */
+		};
+
+		mtu3-pwm {
+			pinmux = <RZG2L_PORT_PINMUX(44, 0, 4)>, /* MTIOC3A */
+				 <RZG2L_PORT_PINMUX(44, 1, 4)>, /* MTIOC3B */
+				 <RZG2L_PORT_PINMUX(44, 2, 4)>, /* MTIOC3C */
+				 <RZG2L_PORT_PINMUX(44, 3, 4)>; /* MTIOC3D */
+		};
+
+#if MTU3_COUNTER_Z_PHASE_SIGNAL
+		mtu3-zphase-clk {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 3)>; /* MTIOC1A */
+		};
+#endif /* MTU3_COUNTER_Z_PHASE_SIGNAL */
+	};
+
 	scif0_pins: scif0 {
 		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>,	/* TxD */
 			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */

arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi

@@ -8,9 +8,6 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
-/* comment the #define statement to disable SCIF2 (SER0) on PMOD1 (CN7) */
-#define PMOD1_SER0	1
-
 / {
 	aliases {
 		serial1 = &scif2;
@@ -115,6 +112,26 @@ wm8978: codec@1a {
 	};
 };
 
+#if PMOD_MTU3
+&mtu3 {
+	pinctrl-0 = <&mtu3_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+#if MTU3_COUNTER_Z_PHASE_SIGNAL
+/* SDHI cd pin is muxed with counter Z phase signal */
+&sdhi1 {
+	status = "disabled";
+};
+#endif /* MTU3_COUNTER_Z_PHASE_SIGNAL */
+
+&spi1 {
+	status = "disabled";
+};
+#endif /* PMOD_MTU3 */
+
 /*
  * To enable SCIF2 (SER0) on PMOD1 (CN7)
  * SW1 should be at position 2->3 so that SER0_CTS# line is activated