dt-bindings: gpio: gpio-mvebu: convert txt binding to DT schema format

Convert the existing device tree binding to DT schema format.

The old binding listed the interrupt-controller and related properties
as required but there are sufficiently many existing usages without it
that the YAML binding does not make the interrupt properties required.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt

@@ -72,7 +72,7 @@ mpp19	19	gpio, uart0(rxd), sdio(pw_off)
 GPIO:
 -----
 For common binding part and usage, refer to
-Documentation/devicetree/bindings/gpio/gpio-mvebu.txt.
+Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml.
 
 Required properties:
 

Documentation/devicetree/bindings/arm/marvell/cp110-system-controller.txt

@@ -156,7 +156,7 @@ GPIO:
 -----
 
 For common binding part and usage, refer to
-Documentation/devicetree/bindings/gpio/gpio-mvebu.txt.
+Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml.
 
 Required properties:
 

Documentation/devicetree/bindings/gpio/gpio-mvebu.txt

-* Marvell EBU GPIO controller
-
-Required properties:
-
-- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
-  "marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".
-
-    "marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
-    Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
-    should be used for the Discovery MV78200.
-
-    "marvel,armadaxp-gpio" should be used for all Armada XP SoCs
-    (MV78230, MV78260, MV78460).
-
-    "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
-    SoCs (either from AP or CP), see
-    Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
-    for specific details about the offset property.
-
-- reg: Address and length of the register set for the device. Only one
-  entry is expected, except for the "marvell,armadaxp-gpio" variant
-  for which two entries are expected: one for the general registers,
-  one for the per-cpu registers. Not used for marvell,armada-8k-gpio.
-
-- interrupts: The list of interrupts that are used for all the pins
-  managed by this GPIO bank. There can be more than one interrupt
-  (example: 1 interrupt per 8 pins on Armada XP, which means 4
-  interrupts per bank of 32 GPIOs).
-
-- interrupt-controller: identifies the node as an interrupt controller
-
-- #interrupt-cells: specifies the number of cells needed to encode an
-  interrupt source. Should be two.
-  The first cell is the GPIO number.
-  The second cell is used to specify flags:
-    bits[3:0] trigger type and level flags:
-      1 = low-to-high edge triggered.
-      2 = high-to-low edge triggered.
-      4 = active high level-sensitive.
-      8 = active low level-sensitive.
-
-- gpio-controller: marks the device node as a gpio controller
-
-- ngpios: number of GPIOs this controller has
-
-- #gpio-cells: Should be two. The first cell is the pin number. The
-  second cell is reserved for flags, unused at the moment.
-
-Optional properties:
-
-In order to use the GPIO lines in PWM mode, some additional optional
-properties are required.
-
-- compatible: Must contain "marvell,armada-370-gpio"
-
-- reg: an additional register set is needed, for the GPIO Blink
-  Counter on/off registers.
-
-- reg-names: Must contain an entry "pwm" corresponding to the
-  additional register range needed for PWM operation.
-
-- #pwm-cells: Should be two. The first cell is the GPIO line number. The
-  second cell is the period in nanoseconds.
-
-- clocks: Must be a phandle to the clock for the GPIO controller.
-
-Example:
-
-		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
-		};
-
-		gpio1: gpio@18140 {
-			compatible = "marvell,armada-370-gpio";
-			reg = <0x18140 0x40>, <0x181c8 0x08>;
-			reg-names = "gpio", "pwm";
-			ngpios = <17>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			#pwm-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <87>, <88>, <89>;
-			clocks = <&coreclk 0>;
-		};

Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell EBU GPIO controller
+
+maintainers:
+  - Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+  - Andrew Lunn <andrew@lunn.ch>
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - marvell,armada-8k-gpio
+          - marvell,orion-gpio
+
+      - items:
+          - enum:
+              - marvell,mv78200-gpio
+              - marvell,armada-370-gpio
+              - marvell,armadaxp-gpio
+          - const: marvell,orion-gpio
+
+  reg:
+    description: |
+      Address and length of the register set for the device. Not used for
+      marvell,armada-8k-gpio.
+
+      For the "marvell,armadaxp-gpio" variant a second entry is expected for
+      the per-cpu registers. For other variants second entry can be provided,
+      for the PWM function using the GPIO Blink Counter on/off registers.
+    minItems: 1
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: gpio
+      - const: pwm
+    minItems: 1
+
+  interrupts:
+    description: |
+      The list of interrupts that are used for all the pins managed by this
+      GPIO bank. There can be more than one interrupt (example: 1 interrupt
+      per 8 pins on Armada XP, which means 4 interrupts per bank of 32
+      GPIOs).
+    minItems: 1
+    maxItems: 4
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  gpio-controller: true
+
+  ngpios:
+    minimum: 1
+    maximum: 32
+
+  "#gpio-cells":
+    const: 2
+
+  "#pwm-cells":
+    description:
+      The first cell is the GPIO line number. The second cell is the period
+      in nanoseconds.
+    const: 2
+
+  clocks:
+    description:
+      Clock(s) used for PWM function.
+    items:
+      - description: Core clock
+      - description: AXI bus clock
+    minItems: 1
+
+  clock-names:
+    items:
+      - const: core
+      - const: axi
+    minItems: 1
+
+required:
+  - compatible
+  - gpio-controller
+  - ngpios
+  - "#gpio-cells"
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: marvell,armada-8k-gpio
+    then:
+      required:
+        - offset
+    else:
+      required:
+        - reg
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: marvell,armadaxp-gpio
+    then:
+      properties:
+        reg:
+          minItems: 2
+        reg-names:
+          minItems: 2
+
+unevaluatedProperties: true
+
+examples:
+  - |
+    gpio@d0018100 {
+      compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio";
+      reg = <0xd0018100 0x40>, <0xd0018800 0x30>;
+      ngpios = <32>;
+      gpio-controller;
+      #gpio-cells = <2>;
+      interrupt-controller;
+      #interrupt-cells = <2>;
+      interrupts = <16>, <17>, <18>, <19>;
+    };
+
+  - |
+    gpio@18140 {
+      compatible = "marvell,armada-370-gpio", "marvell,orion-gpio";
+      reg = <0x18140 0x40>, <0x181c8 0x08>;
+      reg-names = "gpio", "pwm";
+      ngpios = <17>;
+      gpio-controller;
+      #gpio-cells = <2>;
+      #pwm-cells = <2>;
+      interrupt-controller;
+      #interrupt-cells = <2>;
+      interrupts = <87>, <88>, <89>;
+      clocks = <&coreclk 0>;
+    };

MAINTAINERS

@@ -16330,7 +16330,7 @@ L:	linux-pwm@vger.kernel.org
 S:	Maintained
 Q:	https://patchwork.ozlabs.org/project/linux-pwm/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm.git
-F:	Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
+F:	Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml
 F:	Documentation/devicetree/bindings/pwm/
 F:	Documentation/driver-api/pwm.rst
 F:	drivers/gpio/gpio-mvebu.c