arm64: dts: apple: t8103: Add root port interrupt routing

Add the interrupt-map properties that are required for INTx
signalling.
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Hector Martin <marcan@marcan.st>

arch/arm64/boot/dts/apple/t8103.dtsi

@@ -278,7 +278,7 @@ pcie0: pcie@690000000 {
 			pinctrl-0 = <&pcie_pins>;
 			pinctrl-names = "default";
 
-			pci@0,0 {
+			port00: pci@0,0 {
 				device_type = "pci";
 				reg = <0x0 0x0 0x0 0x0 0x0>;
 				reset-gpios = <&pinctrl_ap 152 0>;
@@ -287,9 +287,18 @@ pci@0,0 {
 				#address-cells = <3>;
 				#size-cells = <2>;
 				ranges;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &port00 0 0 0 0>,
+						<0 0 0 2 &port00 0 0 0 1>,
+						<0 0 0 3 &port00 0 0 0 2>,
+						<0 0 0 4 &port00 0 0 0 3>;
 			};
 
-			pci@1,0 {
+			port01: pci@1,0 {
 				device_type = "pci";
 				reg = <0x800 0x0 0x0 0x0 0x0>;
 				reset-gpios = <&pinctrl_ap 153 0>;
@@ -298,9 +307,18 @@ pci@1,0 {
 				#address-cells = <3>;
 				#size-cells = <2>;
 				ranges;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &port01 0 0 0 0>,
+						<0 0 0 2 &port01 0 0 0 1>,
+						<0 0 0 3 &port01 0 0 0 2>,
+						<0 0 0 4 &port01 0 0 0 3>;
 			};
 
-			pci@2,0 {
+			port02: pci@2,0 {
 				device_type = "pci";
 				reg = <0x1000 0x0 0x0 0x0 0x0>;
 				reset-gpios = <&pinctrl_ap 33 0>;
@@ -309,6 +327,15 @@ pci@2,0 {
 				#address-cells = <3>;
 				#size-cells = <2>;
 				ranges;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &port02 0 0 0 0>,
+						<0 0 0 2 &port02 0 0 0 1>,
+						<0 0 0 3 &port02 0 0 0 2>,
+						<0 0 0 4 &port02 0 0 0 3>;
 			};
 		};
 	};