pinctrl: msm: Add msm8960 definitions

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt

+Qualcomm MSM8960 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8960 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,msm8960-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio151,
+		    sdc1_clk,
+		    sdc1_cmd,
+		    sdc1_data
+		    sdc3_clk,
+		    sdc3_cmd,
+		    sdc3_data
+
+- function:
+	Usage: optional
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+		    audio_pcm, bt, cam_mclk0, cam_mclk1, cam_mclk2,
+		    codec_mic_i2s, codec_spkr_i2s, ext_gps, fm, gps_blanking,
+		    gps_pps_in, gps_pps_out, gp_clk_0a, gp_clk_0b, gp_clk_1a,
+		    gp_clk_1b, gp_clk_2a, gp_clk_2b, gp_mn, gp_pdm_0a,
+		    gp_pdm_0b, gp_pdm_1a, gp_pdm_1b, gp_pdm_2a, gp_pdm_2b,
+		    gsbi1, gsbi1_spi_cs1_n, gsbi1_spi_cs2a_n, gsbi1_spi_cs2b_n,
+		    gsbi1_spi_cs3_n, gsbi2, gsbi2_spi_cs1_n, gsbi2_spi_cs2_n,
+		    gsbi2_spi_cs3_n, gsbi3, gsbi4, gsbi4_3d_cam_i2c_l,
+		    gsbi4_3d_cam_i2c_r, gsbi5, gsbi5_3d_cam_i2c_l,
+		    gsbi5_3d_cam_i2c_r, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10,
+		    gsbi11, gsbi11_spi_cs1a_n, gsbi11_spi_cs1b_n,
+		    gsbi11_spi_cs2a_n, gsbi11_spi_cs2b_n, gsbi11_spi_cs3_n,
+		    gsbi12, hdmi_cec, hdmi_ddc_clock, hdmi_ddc_data,
+		    hdmi_hot_plug_detect, hsic, mdp_vsync, mi2s, mic_i2s,
+		    pmb_clk, pmb_ext_ctrl, ps_hold, rpm_wdog, sdc2, sdc4, sdc5,
+		    slimbus1, slimbus2, spkr_i2s, ssbi1, ssbi2, ssbi_ext_gps,
+		    ssbi_pmic2, ssbi_qpa1, ssbi_ts, tsif1, tsif2, ts_eoc,
+		    usb_fs1, usb_fs1_oe, usb_fs1_oe_n, usb_fs2, usb_fs2_oe,
+		    usb_fs2_oe_n, vfe_camif_timer1_a, vfe_camif_timer1_b,
+		    vfe_camif_timer2, vfe_camif_timer3_a, vfe_camif_timer3_b,
+		    vfe_camif_timer4_a, vfe_camif_timer4_b, vfe_camif_timer4_c,
+		    vfe_camif_timer5_a, vfe_camif_timer5_b, vfe_camif_timer6_a,
+		    vfe_camif_timer6_b, vfe_camif_timer6_c, vfe_camif_timer7_a,
+		    vfe_camif_timer7_b, vfe_camif_timer7_c, wlan
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	msmgpio: pinctrl@800000 {
+		compatible = "qcom,msm8960-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 16 0x4>;
+
+		gsbi8_uart: gsbi8-uart {
+			mux {
+				pins = "gpio34", "gpio35";
+				function = "gsbi8";
+			};
+
+			tx {
+				pins = "gpio34";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio35";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};

drivers/pinctrl/Kconfig

@@ -256,6 +256,14 @@ config PINCTRL_IPQ8064
 	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
 	  Qualcomm TLMM block found in the Qualcomm IPQ8064 platform.
 
+config PINCTRL_MSM8960
+	tristate "Qualcomm 8960 pin controller driver"
+	depends on GPIOLIB && OF
+	select PINCTRL_MSM
+	help
+	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+	  Qualcomm TLMM block found in the Qualcomm 8960 platform.
+
 config PINCTRL_MSM8X74
 	tristate "Qualcomm 8x74 pin controller driver"
 	depends on GPIOLIB && OF && (ARCH_QCOM || COMPILE_TEST)

drivers/pinctrl/Makefile

@@ -42,6 +42,7 @@ obj-$(CONFIG_PINCTRL_IMX28)	+= pinctrl-imx28.o
 obj-$(CONFIG_PINCTRL_MSM)	+= pinctrl-msm.o
 obj-$(CONFIG_PINCTRL_APQ8064)	+= pinctrl-apq8064.o
 obj-$(CONFIG_PINCTRL_IPQ8064)	+= pinctrl-ipq8064.o
+obj-$(CONFIG_PINCTRL_MSM8960)	+= pinctrl-msm8960.o
 obj-$(CONFIG_PINCTRL_MSM8X74)	+= pinctrl-msm8x74.o
 obj-$(CONFIG_PINCTRL_NOMADIK)	+= pinctrl-nomadik.o
 obj-$(CONFIG_PINCTRL_STN8815)	+= pinctrl-nomadik-stn8815.o