ARM: dts: omap3-gta04: Add USB host support

Define USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap3-gta04.dts

@@ -74,9 +74,30 @@ lcd_in: endpoint {
 			};
 		};
 	};
+
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_pins
+	>;
+
+	hsusb2_pins: pinmux_hsusb2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+
 	uart1_pins: pinmux_uart1_pins {
 		pinctrl-single,pins = <
 			0x152 (PIN_INPUT | MUX_MODE0)		/* uart1_rx.uart1_rx */
@@ -144,6 +165,22 @@ dss_dpi_pins: pinmux_dss_dpi_pins {
 };
 
 &omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_2_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
+
 	spi_gpio_pins: spi_gpio_pinmux {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE4) /* clk */
@@ -259,6 +296,14 @@ &usb_otg_hs {
 	power = <50>;
 };
 
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};
+
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;