Commit 16541c87 authored by Kyle McMartin's avatar Kyle McMartin Committed by Kyle McMartin

[PARISC] Clean up printk in superio.c

Clean up some of the messages printed by the superio driver
by defining a prefix instead of duplicating it in every message.
Also some small coding style cleanups.
Signed-off-by: default avatarKyle McMartin <kyle@parisc-linux.org>
parent 81a3de3e
......@@ -89,6 +89,9 @@ static struct superio_device sio_dev;
#define DBG_INIT(x...)
#endif
#define SUPERIO "SuperIO"
#define PFX SUPERIO ": "
static irqreturn_t
superio_interrupt(int parent_irq, void *devp, struct pt_regs *regs)
{
......@@ -117,7 +120,7 @@ superio_interrupt(int parent_irq, void *devp, struct pt_regs *regs)
local_irq = results & 0x0f;
if (local_irq == 2 || local_irq > 7) {
printk(KERN_ERR "SuperIO: slave interrupted!\n");
printk(KERN_ERR PFX "slave interrupted!\n");
return IRQ_HANDLED;
}
......@@ -128,7 +131,7 @@ superio_interrupt(int parent_irq, void *devp, struct pt_regs *regs)
outb(OCW3_ISR,IC_PIC1+0);
results = inb(IC_PIC1+0);
if ((results & 0x80) == 0) { /* if ISR7 not set: spurious */
printk(KERN_WARNING "SuperIO: spurious interrupt!\n");
printk(KERN_WARNING PFX "spurious interrupt!\n");
return IRQ_HANDLED;
}
}
......@@ -163,27 +166,27 @@ superio_init(struct pci_dev *pcidev)
/* ...then properly fixup the USB to point at suckyio PIC */
sio->usb_pdev->irq = superio_fixup_irq(sio->usb_pdev);
printk(KERN_INFO "SuperIO: Found NS87560 Legacy I/O device at %s (IRQ %i) \n",
printk(KERN_INFO PFX "Found NS87560 Legacy I/O device at %s (IRQ %i) \n",
pci_name(pdev), pdev->irq);
pci_read_config_dword (pdev, SIO_SP1BAR, &sio->sp1_base);
sio->sp1_base &= ~1;
printk (KERN_INFO "SuperIO: Serial port 1 at 0x%x\n", sio->sp1_base);
printk(KERN_INFO PFX "Serial port 1 at 0x%x\n", sio->sp1_base);
pci_read_config_dword (pdev, SIO_SP2BAR, &sio->sp2_base);
sio->sp2_base &= ~1;
printk (KERN_INFO "SuperIO: Serial port 2 at 0x%x\n", sio->sp2_base);
printk(KERN_INFO PFX "Serial port 2 at 0x%x\n", sio->sp2_base);
pci_read_config_dword (pdev, SIO_PPBAR, &sio->pp_base);
sio->pp_base &= ~1;
printk (KERN_INFO "SuperIO: Parallel port at 0x%x\n", sio->pp_base);
printk(KERN_INFO PFX "Parallel port at 0x%x\n", sio->pp_base);
pci_read_config_dword (pdev, SIO_FDCBAR, &sio->fdc_base);
sio->fdc_base &= ~1;
printk (KERN_INFO "SuperIO: Floppy controller at 0x%x\n", sio->fdc_base);
printk(KERN_INFO PFX "Floppy controller at 0x%x\n", sio->fdc_base);
pci_read_config_dword (pdev, SIO_ACPIBAR, &sio->acpi_base);
sio->acpi_base &= ~1;
printk (KERN_INFO "SuperIO: ACPI at 0x%x\n", sio->acpi_base);
printk(KERN_INFO PFX "ACPI at 0x%x\n", sio->acpi_base);
request_region (IC_PIC1, 0x1f, "pic1");
request_region (IC_PIC2, 0x1f, "pic2");
......@@ -263,14 +266,14 @@ superio_init(struct pci_dev *pcidev)
/* Setup USB power regulation */
outb(1, sio->acpi_base + USB_REG_CR);
if (inb(sio->acpi_base + USB_REG_CR) & 1)
printk(KERN_INFO "SuperIO: USB regulator enabled\n");
printk(KERN_INFO PFX "USB regulator enabled\n");
else
printk(KERN_ERR "USB regulator not initialized!\n");
printk(KERN_ERR PFX "USB regulator not initialized!\n");
if (request_irq(pdev->irq, superio_interrupt, SA_INTERRUPT,
"SuperIO", (void *)sio)) {
SUPERIO, (void *)sio)) {
printk(KERN_ERR "SuperIO: could not get irq\n");
printk(KERN_ERR PFX "could not get irq\n");
BUG();
return;
}
......@@ -284,7 +287,7 @@ static void superio_disable_irq(unsigned int irq)
u8 r8;
if ((irq < 1) || (irq == 2) || (irq > 7)) {
printk(KERN_ERR "SuperIO: Illegal irq number.\n");
printk(KERN_ERR PFX "Illegal irq number.\n");
BUG();
return;
}
......@@ -301,7 +304,7 @@ static void superio_enable_irq(unsigned int irq)
u8 r8;
if ((irq < 1) || (irq == 2) || (irq > 7)) {
printk(KERN_ERR "SuperIO: Illegal irq number (%d).\n", irq);
printk(KERN_ERR PFX "Illegal irq number (%d).\n", irq);
BUG();
return;
}
......@@ -319,7 +322,7 @@ static unsigned int superio_startup_irq(unsigned int irq)
}
static struct hw_interrupt_type superio_interrupt_type = {
.typename = "SuperIO",
.typename = SUPERIO,
.startup = superio_startup_irq,
.shutdown = superio_disable_irq,
.enable = superio_enable_irq,
......@@ -413,7 +416,7 @@ static void __devinit superio_serial_init(void)
retval = early_serial_setup(&serial[0]);
if (retval < 0) {
printk(KERN_WARNING "SuperIO: Register Serial #0 failed.\n");
printk(KERN_WARNING PFX "Register Serial #0 failed.\n");
return;
}
......@@ -423,7 +426,7 @@ static void __devinit superio_serial_init(void)
retval = early_serial_setup(&serial[1]);
if (retval < 0)
printk(KERN_WARNING "SuperIO: Register Serial #1 failed.\n");
printk(KERN_WARNING PFX "Register Serial #1 failed.\n");
#endif /* CONFIG_SERIAL_8250 */
}
......@@ -437,7 +440,7 @@ static void __devinit superio_parport_init(void)
PARPORT_DMA_NONE /* dma */,
NULL /*struct pci_dev* */) )
printk(KERN_WARNING "SuperIO: Probing parallel port failed.\n");
printk(KERN_WARNING PFX "Probing parallel port failed.\n");
#endif /* CONFIG_PARPORT_PC */
}
......@@ -499,7 +502,7 @@ static struct pci_device_id superio_tbl[] = {
};
static struct pci_driver superio_driver = {
.name = "SuperIO",
.name = SUPERIO,
.id_table = superio_tbl,
.probe = superio_probe,
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment