Merge git://www.linux-watchdog.org/linux-watchdog

Pull watchdog updates from Wim Van Sebroeck:
 - new driver for bcm281xx watchdog device
 - new driver for gpio based watchdog devices
 - remove DEFINE_PCI_DEVICE_TABLE macro for watchdog device drivers
 - conversion of davinci_wdt and mpc8xxx_wdt to watchdog core
 - improvements on davinci_wdt, at91/dt, at91sam9_wdt and s3c2410_wdt
 - Auto-detect IO address and expand supported chips on w836* super-I/O
   chipsets
 - core: Make dt "timeout-sec" property work on drivers w/out min/max
 - fix Kconfig dependencies
 - sirf: Remove redundant of_match_ptr helper
 - mach-moxart: add restart handler
 - hpwdt patch to display better panic information
 - imx2_wdt: disable watchdog timer during low power mode

* git://www.linux-watchdog.org/linux-watchdog: (31 commits)
  watchdog: w83627hf_wdt: Reset watchdog trigger during initialization
  watchdog: w83627hf: Add support for W83697HF and W83697UG
  watchdog: w83627hf: Auto-detect IO address and supported chips
  watchdog: at91sam9_wdt: increase security margin on watchdog counter reset
  watchdog: at91sam9_wdt: avoid spurious watchdog reset during init
  watchdog: at91sam9_wdt: fix secs_to_ticks
  ARM: at91/dt: add watchdog properties to kizbox board
  ARM: at91/dt: add sam9 watchdog default options to SoCs
  watchdog: at91sam9_wdt: update device tree doc
  watchdog: at91sam9_wdt: better watchdog support
  watchdog: sp805_wdt depends also on ARM64
  watchdog: mach-moxart: add restart handler
  watchdog: mpc8xxx_wdt convert to watchdog core
  watchdog: sirf: Remove redundant of_match_ptr helper
  watchdog: hpwdt patch to display informative string
  watchdog: dw_wdt: remove build dependencies
  watchdog: imx2_wdt: disable watchdog timer during low power mode
  watchdog: s3c2410_wdt: Report when the watchdog reset the system
  watchdog: s3c2410_wdt: use syscon regmap interface to configure pmu register
  watchdog: s3c2410_wdt: Handle rounding a little better for timeout
  ...

Documentation/devicetree/bindings/watchdog/atmel-wdt.txt

@@ -9,11 +9,37 @@ Required properties:
 
 Optional properties:
 - timeout-sec: contains the watchdog timeout in seconds.
+- interrupts : Should contain WDT interrupt.
+- atmel,max-heartbeat-sec : Should contain the maximum heartbeat value in
+	seconds. This value should be less or equal to 16. It is used to
+	compute the WDV field.
+- atmel,min-heartbeat-sec : Should contain the minimum heartbeat value in
+	seconds. This value must be smaller than the max-heartbeat-sec value.
+	It is used to compute the WDD field.
+- atmel,watchdog-type : Should be "hardware" or "software". Hardware watchdog
+	use the at91 watchdog reset. Software watchdog use the watchdog
+	interrupt to trigger a software reset.
+- atmel,reset-type : Should be "proc" or "all".
+	"all" : assert peripherals and processor reset signals
+	"proc" : assert the processor reset signal
+	This is valid only when using "hardware" watchdog.
+- atmel,disable : Should be present if you want to disable the watchdog.
+- atmel,idle-halt : Should be present if you want to stop the watchdog when
+	entering idle state.
+- atmel,dbg-halt : Should be present if you want to stop the watchdog when
+	entering debug state.
 
 Example:
-
 	watchdog@fffffd40 {
 		compatible = "atmel,at91sam9260-wdt";
 		reg = <0xfffffd40 0x10>;
-		timeout-sec = <10>;
+		interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+		timeout-sec = <15>;
+		atmel,watchdog-type = "hardware";
+		atmel,reset-type = "all";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+		atmel,max-heartbeat-sec = <16>;
+		atmel,min-heartbeat-sec = <0>;
+		status = "okay";
 	};

Documentation/devicetree/bindings/watchdog/davinci-wdt.txt

-DaVinci Watchdog Timer (WDT) Controller
+Texas Instruments DaVinci/Keystone Watchdog Timer (WDT) Controller
 
 Required properties:
-- compatible : Should be "ti,davinci-wdt"
+- compatible : Should be "ti,davinci-wdt", "ti,keystone-wdt"
 - reg : Should contain WDT registers location and length
 
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+- clocks : the clock feeding the watchdog timer.
+	   Needed if platform uses clocks.
+	   See clock-bindings.txt
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/spruer5b/spruer5b.pdf
+Keystone - http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf
+
 Examples:
 
 wdt: wdt@2320000 {
 	compatible = "ti,davinci-wdt";
 	reg = <0x02320000 0x80>;
+	timeout-sec = <30>;
+	clocks = <&clkwdtimer0>;
 };

Documentation/devicetree/bindings/watchdog/gpio-wdt.txt

+* GPIO-controlled Watchdog
+
+Required Properties:
+- compatible: Should contain "linux,wdt-gpio".
+- gpios: From common gpio binding; gpio connection to WDT reset pin.
+- hw_algo: The algorithm used by the driver. Should be one of the
+  following values:
+  - toggle: Either a high-to-low or a low-to-high transition clears
+    the WDT counter. The watchdog timer is disabled when GPIO is
+    left floating or connected to a three-state buffer.
+  - level: Low or high level starts counting WDT timeout,
+    the opposite level disables the WDT. Active level is determined
+    by the GPIO flags.
+- hw_margin_ms: Maximum time to reset watchdog circuit (milliseconds).
+
+Example:
+	watchdog: watchdog {
+		/* ADM706 */
+		compatible = "linux,wdt-gpio";
+		gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+		hw_algo = "toggle";
+		hw_margin_ms = <1600>;
+	};

Documentation/devicetree/bindings/watchdog/samsung-wdt.txt

@@ -5,10 +5,29 @@ after a preset amount of time during which the WDT reset event has not
 occurred.
 
 Required properties:
-- compatible : should be "samsung,s3c2410-wdt"
+- compatible : should be one among the following
+	(a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs
+	(b) "samsung,exynos5250-wdt" for Exynos5250
+	(c) "samsung,exynos5420-wdt" for Exynos5420
+
 - reg : base physical address of the controller and length of memory mapped
 	region.
 - interrupts : interrupt number to the cpu.
+- samsung,syscon-phandle : reference to syscon node (This property required only
+	in case of compatible being "samsung,exynos5250-wdt" or "samsung,exynos5420-wdt".
+	In case of Exynos5250 and 5420 this property points to syscon node holding the PMU
+	base address)
 
 Optional properties:
 - timeout-sec : contains the watchdog timeout in seconds.
+
+Example:
+
+watchdog@101D0000 {
+	compatible = "samsung,exynos5250-wdt";
+	reg = <0x101D0000 0x100>;
+	interrupts = <0 42 0>;
+	clocks = <&clock 336>;
+	clock-names = "watchdog";
+	samsung,syscon-phandle = <&pmu_syscon>;
+};

arch/arm/boot/dts/at91sam9260.dtsi

@@ -648,6 +648,11 @@ trigger@3 {
 			watchdog@fffffd40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffd40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				atmel,idle-halt;
 				status = "disabled";
 			};
 		};

arch/arm/boot/dts/at91sam9263.dtsi

@@ -552,6 +552,11 @@ mmc1: mmc@fff84000 {
 			watchdog@fffffd40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffd40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -706,6 +706,11 @@ mmc1: mmc@fffd0000 {
 			watchdog@fffffd40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffd40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -541,6 +541,11 @@ spi1: spi@f0004000 {
 			watchdog@fffffe40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffe40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -754,6 +754,11 @@ ep6 {
 			watchdog@fffffe40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffe40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/kizbox.dts

@@ -53,6 +53,12 @@ macb0: ethernet@fffc4000 {
 				status = "okay";
 			};
 
+			watchdog@fffffd40 {
+				timeout-sec = <15>;
+				atmel,max-heartbeat-sec = <16>;
+				atmel,min-heartbeat-sec = <0>;
+				status = "okay";
+			};
 		};
 
 		nand0: nand@40000000 {

arch/arm/boot/dts/sama5d3.dtsi

@@ -1092,6 +1092,11 @@ pit: timer@fffffe30 {
 			watchdog@fffffe40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffe40 0x10>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH 7>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/configs/bcm_defconfig

@@ -126,3 +126,6 @@ CONFIG_CRC7=y
 CONFIG_XZ_DEC=y
 CONFIG_AVERAGE=y
 CONFIG_PINCTRL_CAPRI=y
+CONFIG_WATCHDOG=y
+CONFIG_BCM_KONA_WDT=y
+CONFIG_BCM_KONA_WDT_DEBUG=y

drivers/watchdog/Kconfig

@@ -87,6 +87,14 @@ config DA9055_WATCHDOG
 	  This driver can also be built as a module.  If so, the module
 	  will be called da9055_wdt.
 
+config GPIO_WATCHDOG
+	tristate "Watchdog device controlled through GPIO-line"
+	depends on OF_GPIO
+	select WATCHDOG_CORE
+	help
+	  If you say yes here you get support for watchdog device
+	  controlled through GPIO-line.
+
 config WM831X_WATCHDOG
 	tristate "WM831x watchdog"
 	depends on MFD_WM831X
@@ -109,7 +117,7 @@ config WM8350_WATCHDOG
 
 config ARM_SP805_WATCHDOG
 	tristate "ARM SP805 Watchdog"
-	depends on ARM && ARM_AMBA
+	depends on (ARM || ARM64) && ARM_AMBA
 	select WATCHDOG_CORE
 	help
 	  ARM Primecell SP805 Watchdog timer. This will reboot your system when
@@ -188,6 +196,7 @@ config S3C2410_WATCHDOG
 	tristate "S3C2410 Watchdog"
 	depends on HAVE_S3C2410_WATCHDOG
 	select WATCHDOG_CORE
+	select MFD_SYSCON if ARCH_EXYNOS5
 	help
 	  Watchdog timer block in the Samsung SoCs. This will reboot
 	  the system when the timer expires with the watchdog enabled.
@@ -214,10 +223,9 @@ config SA1100_WATCHDOG
 
 config DW_WATCHDOG
 	tristate "Synopsys DesignWare watchdog"
-	depends on ARM && HAVE_CLK
 	help
 	  Say Y here if to include support for the Synopsys DesignWare
-	  watchdog timer found in many ARM chips.
+	  watchdog timer found in many chips.
 	  To compile this driver as a module, choose M here: the
 	  module will be called dw_wdt.
 
@@ -270,10 +278,11 @@ config IOP_WATCHDOG
 
 config DAVINCI_WATCHDOG
 	tristate "DaVinci watchdog"
-	depends on ARCH_DAVINCI
+	depends on ARCH_DAVINCI || ARCH_KEYSTONE
+	select WATCHDOG_CORE
 	help
 	  Say Y here if to include support for the watchdog timer
-	  in the DaVinci DM644x/DM646x processors.
+	  in the DaVinci DM644x/DM646x or Keystone processors.
 	  To compile this driver as a module, choose M here: the
 	  module will be called davinci_wdt.
 
@@ -883,13 +892,22 @@ config VIA_WDT
 	Most people will say N.
 
 config W83627HF_WDT
-	tristate "W83627HF/W83627DHG Watchdog Timer"
+	tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
 	depends on X86
 	select WATCHDOG_CORE
 	---help---
-	  This is the driver for the hardware watchdog on the W83627HF chipset
-	  as used in Advantech PC-9578 and Tyan S2721-533 motherboards
-	  (and likely others). The driver also supports the W83627DHG chip.
+	  This is the driver for the hardware watchdog on the following
+	  Super I/O chips.
+		W83627DHG/DHG-P/EHF/EHG/F/G/HF/S/SF/THF/UHG/UG
+		W83637HF
+		W83667HG/HG-B
+		W83687THF
+		W83697HF
+		W83697UG
+		NCT6775
+		NCT6776
+		NCT6779
+
 	  This watchdog simply watches your kernel to make sure it doesn't
 	  freeze, and if it does, it reboots your computer after a certain
 	  amount of time.
@@ -1139,6 +1157,28 @@ config BCM2835_WDT
 	  To compile this driver as a loadable module, choose M here.
 	  The module will be called bcm2835_wdt.
 
+config BCM_KONA_WDT
+	tristate "BCM Kona Watchdog"
+	depends on ARCH_BCM
+	select WATCHDOG_CORE
+	help
+	  Support for the watchdog timer on the following Broadcom BCM281xx
+	  family, which includes BCM11130, BCM11140, BCM11351, BCM28145 and
+	  BCM28155 variants.
+
+	  Say 'Y' or 'M' here to enable the driver. The module will be called
+	  bcm_kona_wdt.
+
+config BCM_KONA_WDT_DEBUG
+	bool "DEBUGFS support for BCM Kona Watchdog"
+	depends on BCM_KONA_WDT
+	help
+	  If enabled, adds /sys/kernel/debug/bcm_kona_wdt/info which provides
+	  access to the driver's internal data structures as well as watchdog
+	  timer hardware registres.
+
+	  If in doubt, say 'N'.
+
 config LANTIQ_WDT
 	tristate "Lantiq SoC watchdog"
 	depends on LANTIQ
@@ -1171,6 +1211,7 @@ config MPC5200_WDT
 config 8xxx_WDT
 	tristate "MPC8xxx Platform Watchdog Timer"
 	depends on PPC_8xx || PPC_83xx || PPC_86xx
+	select WATCHDOG_CORE
 	help
 	  This driver is for a SoC level watchdog that exists on some
 	  Freescale PowerPC processors. So far this driver supports:

drivers/watchdog/Makefile

@@ -57,6 +57,7 @@ obj-$(CONFIG_RETU_WATCHDOG) += retu_wdt.o
 obj-$(CONFIG_BCM2835_WDT) += bcm2835_wdt.o
 obj-$(CONFIG_MOXART_WDT) += moxart_wdt.o
 obj-$(CONFIG_SIRFSOC_WATCHDOG) += sirfsoc_wdt.o
+obj-$(CONFIG_BCM_KONA_WDT) += bcm_kona_wdt.o
 
 # AVR32 Architecture
 obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
@@ -171,6 +172,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
 # Architecture Independent
 obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
 obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
+obj-$(CONFIG_GPIO_WATCHDOG)	+= gpio_wdt.o
 obj-$(CONFIG_WM831X_WATCHDOG) += wm831x_wdt.o
 obj-$(CONFIG_WM8350_WATCHDOG) += wm8350_wdt.o
 obj-$(CONFIG_MAX63XX_WATCHDOG) += max63xx_wdt.o

drivers/watchdog/alim1535_wdt.c

@@ -301,7 +301,7 @@ static int ali_notify_sys(struct notifier_block *this,
  *	want to register another driver on the same PCI id.
  */
 
-static DEFINE_PCI_DEVICE_TABLE(ali_pci_tbl) __used = {
+static const struct pci_device_id ali_pci_tbl[] __used = {
 	{ PCI_VENDOR_ID_AL, 0x1533, PCI_ANY_ID, PCI_ANY_ID,},
 	{ PCI_VENDOR_ID_AL, 0x1535, PCI_ANY_ID, PCI_ANY_ID,},
 	{ 0, },

drivers/watchdog/alim7101_wdt.c

@@ -414,7 +414,7 @@ static int __init alim7101_wdt_init(void)
 module_init(alim7101_wdt_init);
 module_exit(alim7101_wdt_unload);
 
-static DEFINE_PCI_DEVICE_TABLE(alim7101_pci_tbl) __used = {
+static const struct pci_device_id alim7101_pci_tbl[] __used = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101) },
 	{ }

drivers/watchdog/bcm_kona_wdt.c

+/*
+ * Copyright (C) 2013 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/watchdog.h>
+
+#define SECWDOG_CTRL_REG		0x00000000
+#define SECWDOG_COUNT_REG		0x00000004
+
+#define SECWDOG_RESERVED_MASK		0x1dffffff
+#define SECWDOG_WD_LOAD_FLAG		0x10000000
+#define SECWDOG_EN_MASK			0x08000000
+#define SECWDOG_SRSTEN_MASK		0x04000000
+#define SECWDOG_RES_MASK		0x00f00000
+#define SECWDOG_COUNT_MASK		0x000fffff
+
+#define SECWDOG_MAX_COUNT		SECWDOG_COUNT_MASK
+#define SECWDOG_CLKS_SHIFT		20
+#define SECWDOG_MAX_RES			15
+#define SECWDOG_DEFAULT_RESOLUTION	4
+#define SECWDOG_MAX_TRY			1000
+
+#define SECS_TO_TICKS(x, w)		((x) << (w)->resolution)
+#define TICKS_TO_SECS(x, w)		((x) >> (w)->resolution)
+
+#define BCM_KONA_WDT_NAME		"bcm_kona_wdt"
+
+struct bcm_kona_wdt {
+	void __iomem *base;
+	/*
+	 * One watchdog tick is 1/(2^resolution) seconds. Resolution can take
+	 * the values 0-15, meaning one tick can be 1s to 30.52us. Our default
+	 * resolution of 4 means one tick is 62.5ms.
+	 *
+	 * The watchdog counter is 20 bits. Depending on resolution, the maximum
+	 * counter value of 0xfffff expires after about 12 days (resolution 0)
+	 * down to only 32s (resolution 15). The default resolution of 4 gives
+	 * us a maximum of about 18 hours and 12 minutes before the watchdog
+	 * times out.
+	 */
+	int resolution;
+	spinlock_t lock;
+#ifdef CONFIG_BCM_KONA_WDT_DEBUG
+	unsigned long busy_count;
+	struct dentry *debugfs;
+#endif
+};
+
+static int secure_register_read(struct bcm_kona_wdt *wdt, uint32_t offset)
+{
+	uint32_t val;
+	unsigned count = 0;
+
+	/*
+	 * If the WD_LOAD_FLAG is set, the watchdog counter field is being
+	 * updated in hardware. Once the WD timer is updated in hardware, it
+	 * gets cleared.
+	 */
+	do {
+		if (unlikely(count > 1))
+			udelay(5);
+		val = readl_relaxed(wdt->base + offset);
+		count++;
+	} while ((val & SECWDOG_WD_LOAD_FLAG) && count < SECWDOG_MAX_TRY);
+
+#ifdef CONFIG_BCM_KONA_WDT_DEBUG
+	/* Remember the maximum number iterations due to WD_LOAD_FLAG */
+	if (count > wdt->busy_count)
+		wdt->busy_count = count;
+#endif
+
+	/* This is the only place we return a negative value. */
+	if (val & SECWDOG_WD_LOAD_FLAG)
+		return -ETIMEDOUT;
+
+	/* We always mask out reserved bits. */
+	val &= SECWDOG_RESERVED_MASK;
+
+	return val;
+}
+
+#ifdef CONFIG_BCM_KONA_WDT_DEBUG
+
+static int bcm_kona_wdt_dbg_show(struct seq_file *s, void *data)
+{
+	int ctl_val, cur_val, ret;
+	unsigned long flags;
+	struct bcm_kona_wdt *wdt = s->private;
+
+	if (!wdt)
+		return seq_puts(s, "No device pointer\n");
+
+	spin_lock_irqsave(&wdt->lock, flags);
+	ctl_val = secure_register_read(wdt, SECWDOG_CTRL_REG);
+	cur_val = secure_register_read(wdt, SECWDOG_COUNT_REG);
+	spin_unlock_irqrestore(&wdt->lock, flags);
+
+	if (ctl_val < 0 || cur_val < 0) {
+		ret = seq_puts(s, "Error accessing hardware\n");
+	} else {
+		int ctl, cur, ctl_sec, cur_sec, res;
+
+		ctl = ctl_val & SECWDOG_COUNT_MASK;
+		res = (ctl_val & SECWDOG_RES_MASK) >> SECWDOG_CLKS_SHIFT;
+		cur = cur_val & SECWDOG_COUNT_MASK;
+		ctl_sec = TICKS_TO_SECS(ctl, wdt);
+		cur_sec = TICKS_TO_SECS(cur, wdt);
+		ret = seq_printf(s, "Resolution: %d / %d\n"
+				"Control: %d s / %d (%#x) ticks\n"
+				"Current: %d s / %d (%#x) ticks\n"
+				"Busy count: %lu\n", res,
+				wdt->resolution, ctl_sec, ctl, ctl, cur_sec,
+				cur, cur, wdt->busy_count);
+	}
+
+	return ret;
+}
+
+static int bcm_kona_dbg_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, bcm_kona_wdt_dbg_show, inode->i_private);
+}
+
+static const struct file_operations bcm_kona_dbg_operations = {
+	.open		= bcm_kona_dbg_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static void bcm_kona_wdt_debug_init(struct platform_device *pdev)
+{
+	struct dentry *dir;
+	struct bcm_kona_wdt *wdt = platform_get_drvdata(pdev);
+
+	if (!wdt)
+		return;
+
+	wdt->debugfs = NULL;
+
+	dir = debugfs_create_dir(BCM_KONA_WDT_NAME, NULL);
+	if (IS_ERR_OR_NULL(dir))
+		return;
+
+	if (debugfs_create_file("info", S_IFREG | S_IRUGO, dir, wdt,
+				&bcm_kona_dbg_operations))
+		wdt->debugfs = dir;
+	else
+		debugfs_remove_recursive(dir);
+}
+
+static void bcm_kona_wdt_debug_exit(struct platform_device *pdev)
+{
+	struct bcm_kona_wdt *wdt = platform_get_drvdata(pdev);
+
+	if (wdt && wdt->debugfs) {
+		debugfs_remove_recursive(wdt->debugfs);
+		wdt->debugfs = NULL;
+	}
+}
+
+#else
+
+static void bcm_kona_wdt_debug_init(struct platform_device *pdev) {}
+static void bcm_kona_wdt_debug_exit(struct platform_device *pdev) {}
+
+#endif /* CONFIG_BCM_KONA_WDT_DEBUG */
+
+static int bcm_kona_wdt_ctrl_reg_modify(struct bcm_kona_wdt *wdt,
+					unsigned mask, unsigned newval)
+{
+	int val;
+	unsigned long flags;
+	int ret = 0;
+
+	spin_lock_irqsave(&wdt->lock, flags);
+
+	val = secure_register_read(wdt, SECWDOG_CTRL_REG);
+	if (val < 0) {
+		ret = val;
+	} else {
+		val &= ~mask;
+		val |= newval;
+		writel_relaxed(val, wdt->base + SECWDOG_CTRL_REG);
+	}
+
+	spin_unlock_irqrestore(&wdt->lock, flags);
+
+	return ret;
+}
+
+static int bcm_kona_wdt_set_resolution_reg(struct bcm_kona_wdt *wdt)
+{
+	if (wdt->resolution > SECWDOG_MAX_RES)
+		return -EINVAL;
+
+	return bcm_kona_wdt_ctrl_reg_modify(wdt, SECWDOG_RES_MASK,
+					wdt->resolution << SECWDOG_CLKS_SHIFT);
+}
+
+static int bcm_kona_wdt_set_timeout_reg(struct watchdog_device *wdog,
+					unsigned watchdog_flags)
+{
+	struct bcm_kona_wdt *wdt = watchdog_get_drvdata(wdog);
+
+	return bcm_kona_wdt_ctrl_reg_modify(wdt, SECWDOG_COUNT_MASK,
+					SECS_TO_TICKS(wdog->timeout, wdt) |
+					watchdog_flags);
+}
+
+static int bcm_kona_wdt_set_timeout(struct watchdog_device *wdog,
+	unsigned int t)
+{
+	wdog->timeout = t;
+	return 0;
+}
+
+static unsigned int bcm_kona_wdt_get_timeleft(struct watchdog_device *wdog)
+{
+	struct bcm_kona_wdt *wdt = watchdog_get_drvdata(wdog);
+	int val;
+	unsigned long flags;
+
+	spin_lock_irqsave(&wdt->lock, flags);
+	val = secure_register_read(wdt, SECWDOG_COUNT_REG);
+	spin_unlock_irqrestore(&wdt->lock, flags);
+
+	if (val < 0)
+		return val;
+
+	return TICKS_TO_SECS(val & SECWDOG_COUNT_MASK, wdt);
+}
+
+static int bcm_kona_wdt_start(struct watchdog_device *wdog)
+{
+	return bcm_kona_wdt_set_timeout_reg(wdog,
+					SECWDOG_EN_MASK | SECWDOG_SRSTEN_MASK);
+}
+
+static int bcm_kona_wdt_stop(struct watchdog_device *wdog)
+{
+	struct bcm_kona_wdt *wdt = watchdog_get_drvdata(wdog);
+
+	return bcm_kona_wdt_ctrl_reg_modify(wdt, SECWDOG_EN_MASK |
+					    SECWDOG_SRSTEN_MASK, 0);
+}
+
+static struct watchdog_ops bcm_kona_wdt_ops = {
+	.owner =	THIS_MODULE,
+	.start =	bcm_kona_wdt_start,
+	.stop =		bcm_kona_wdt_stop,
+	.set_timeout =	bcm_kona_wdt_set_timeout,
+	.get_timeleft =	bcm_kona_wdt_get_timeleft,
+};
+
+static struct watchdog_info bcm_kona_wdt_info = {
+	.options =	WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE |
+			WDIOF_KEEPALIVEPING,
+	.identity =	"Broadcom Kona Watchdog Timer",
+};
+
+static struct watchdog_device bcm_kona_wdt_wdd = {
+	.info =		&bcm_kona_wdt_info,
+	.ops =		&bcm_kona_wdt_ops,
+	.min_timeout =	1,
+	.max_timeout =	SECWDOG_MAX_COUNT >> SECWDOG_DEFAULT_RESOLUTION,
+	.timeout =	SECWDOG_MAX_COUNT >> SECWDOG_DEFAULT_RESOLUTION,
+};
+
+static void bcm_kona_wdt_shutdown(struct platform_device *pdev)
+{
+	bcm_kona_wdt_stop(&bcm_kona_wdt_wdd);
+}
+
+static int bcm_kona_wdt_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct bcm_kona_wdt *wdt;
+	struct resource *res;
+	int ret;
+
+	wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
+	if (!wdt)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	wdt->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(wdt->base))
+		return -ENODEV;
+
+	wdt->resolution = SECWDOG_DEFAULT_RESOLUTION;
+	ret = bcm_kona_wdt_set_resolution_reg(wdt);
+	if (ret) {
+		dev_err(dev, "Failed to set resolution (error: %d)", ret);
+		return ret;
+	}
+
+	spin_lock_init(&wdt->lock);
+	platform_set_drvdata(pdev, wdt);
+	watchdog_set_drvdata(&bcm_kona_wdt_wdd, wdt);
+
+	ret = bcm_kona_wdt_set_timeout_reg(&bcm_kona_wdt_wdd, 0);
+	if (ret) {
+		dev_err(dev, "Failed set watchdog timeout");
+		return ret;
+	}
+
+	ret = watchdog_register_device(&bcm_kona_wdt_wdd);
+	if (ret) {
+		dev_err(dev, "Failed to register watchdog device");
+		return ret;
+	}
+
+	bcm_kona_wdt_debug_init(pdev);
+	dev_dbg(dev, "Broadcom Kona Watchdog Timer");
+
+	return 0;
+}
+
+static int bcm_kona_wdt_remove(struct platform_device *pdev)
+{
+	bcm_kona_wdt_debug_exit(pdev);
+	bcm_kona_wdt_shutdown(pdev);
+	watchdog_unregister_device(&bcm_kona_wdt_wdd);
+	dev_dbg(&pdev->dev, "Watchdog driver disabled");
+
+	return 0;
+}
+
+static const struct of_device_id bcm_kona_wdt_of_match[] = {
+	{ .compatible = "brcm,kona-wdt", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, bcm_kona_wdt_of_match);
+
+static struct platform_driver bcm_kona_wdt_driver = {
+	.driver = {
+			.name = BCM_KONA_WDT_NAME,
+			.owner = THIS_MODULE,
+			.of_match_table = bcm_kona_wdt_of_match,
+		  },
+	.probe = bcm_kona_wdt_probe,
+	.remove = bcm_kona_wdt_remove,
+	.shutdown = bcm_kona_wdt_shutdown,
+};
+
+module_platform_driver(bcm_kona_wdt_driver);
+
+MODULE_ALIAS("platform:" BCM_KONA_WDT_NAME);
+MODULE_AUTHOR("Markus Mayer <mmayer@broadcom.com>");
+MODULE_DESCRIPTION("Broadcom Kona Watchdog Driver");
+MODULE_LICENSE("GPL v2");

drivers/watchdog/davinci_wdt.c

@@ -3,7 +3,7 @@
  *
  * Watchdog driver for DaVinci DM644x/DM646x processors
  *
- * Copyright (C) 2006 Texas Instruments.
+ * Copyright (C) 2006-2013 Texas Instruments.
  *
  * 2007 (c) MontaVista Software, Inc. This file is licensed under
  * the terms of the GNU General Public License version 2. This program
@@ -15,18 +15,12 @@
 #include <linux/moduleparam.h>
 #include <linux/types.h>
 #include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/miscdevice.h>
 #include <linux/watchdog.h>
 #include <linux/init.h>
-#include <linux/bitops.h>
 #include <linux/platform_device.h>
-#include <linux/spinlock.h>
-#include <linux/uaccess.h>
 #include <linux/io.h>
 #include <linux/device.h>
 #include <linux/clk.h>
-#include <linux/slab.h>
 #include <linux/err.h>
 
 #define MODULE_NAME "DAVINCI-WDT: "
@@ -61,142 +55,103 @@
 #define WDKEY_SEQ0		(0xa5c6 << 16)
 #define WDKEY_SEQ1		(0xda7e << 16)
 
-static int heartbeat = DEFAULT_HEARTBEAT;
+static int heartbeat;
 
-static DEFINE_SPINLOCK(io_lock);
-static unsigned long wdt_status;
-#define WDT_IN_USE        0
-#define WDT_OK_TO_CLOSE   1
-#define WDT_REGION_INITED 2
-#define WDT_DEVICE_INITED 3
-
-static void __iomem	*wdt_base;
-struct clk		*wdt_clk;
-
-static void wdt_service(void)
-{
-	spin_lock(&io_lock);
-
-	/* put watchdog in service state */
-	iowrite32(WDKEY_SEQ0, wdt_base + WDTCR);
-	/* put watchdog in active state */
-	iowrite32(WDKEY_SEQ1, wdt_base + WDTCR);
-
-	spin_unlock(&io_lock);
-}
+/*
+ * struct to hold data for each WDT device
+ * @base - base io address of WD device
+ * @clk - source clock of WDT
+ * @wdd - hold watchdog device as is in WDT core
+ */
+struct davinci_wdt_device {
+	void __iomem		*base;
+	struct clk		*clk;
+	struct watchdog_device	wdd;
+};
 
-static void wdt_enable(void)
+static int davinci_wdt_start(struct watchdog_device *wdd)
 {
 	u32 tgcr;
 	u32 timer_margin;
 	unsigned long wdt_freq;
+	struct davinci_wdt_device *davinci_wdt = watchdog_get_drvdata(wdd);
 
-	wdt_freq = clk_get_rate(wdt_clk);
-
-	spin_lock(&io_lock);
+	wdt_freq = clk_get_rate(davinci_wdt->clk);
 
 	/* disable, internal clock source */
-	iowrite32(0, wdt_base + TCR);
+	iowrite32(0, davinci_wdt->base + TCR);
 	/* reset timer, set mode to 64-bit watchdog, and unreset */
-	iowrite32(0, wdt_base + TGCR);
+	iowrite32(0, davinci_wdt->base + TGCR);
 	tgcr = TIMMODE_64BIT_WDOG | TIM12RS_UNRESET | TIM34RS_UNRESET;
-	iowrite32(tgcr, wdt_base + TGCR);
+	iowrite32(tgcr, davinci_wdt->base + TGCR);
 	/* clear counter regs */
-	iowrite32(0, wdt_base + TIM12);
-	iowrite32(0, wdt_base + TIM34);
+	iowrite32(0, davinci_wdt->base + TIM12);
+	iowrite32(0, davinci_wdt->base + TIM34);
 	/* set timeout period */
-	timer_margin = (((u64)heartbeat * wdt_freq) & 0xffffffff);
-	iowrite32(timer_margin, wdt_base + PRD12);
-	timer_margin = (((u64)heartbeat * wdt_freq) >> 32);
-	iowrite32(timer_margin, wdt_base + PRD34);
+	timer_margin = (((u64)wdd->timeout * wdt_freq) & 0xffffffff);
+	iowrite32(timer_margin, davinci_wdt->base + PRD12);
+	timer_margin = (((u64)wdd->timeout * wdt_freq) >> 32);
+	iowrite32(timer_margin, davinci_wdt->base + PRD34);
 	/* enable run continuously */
-	iowrite32(ENAMODE12_PERIODIC, wdt_base + TCR);
+	iowrite32(ENAMODE12_PERIODIC, davinci_wdt->base + TCR);
 	/* Once the WDT is in pre-active state write to
 	 * TIM12, TIM34, PRD12, PRD34, TCR, TGCR, WDTCR are
 	 * write protected (except for the WDKEY field)
 	 */
 	/* put watchdog in pre-active state */
-	iowrite32(WDKEY_SEQ0 | WDEN, wdt_base + WDTCR);
+	iowrite32(WDKEY_SEQ0 | WDEN, davinci_wdt->base + WDTCR);
 	/* put watchdog in active state */
-	iowrite32(WDKEY_SEQ1 | WDEN, wdt_base + WDTCR);
-
-	spin_unlock(&io_lock);
+	iowrite32(WDKEY_SEQ1 | WDEN, davinci_wdt->base + WDTCR);
+	return 0;
 }
 
-static int davinci_wdt_open(struct inode *inode, struct file *file)
+static int davinci_wdt_ping(struct watchdog_device *wdd)
 {
-	if (test_and_set_bit(WDT_IN_USE, &wdt_status))
-		return -EBUSY;
-
-	wdt_enable();
+	struct davinci_wdt_device *davinci_wdt = watchdog_get_drvdata(wdd);
 
-	return nonseekable_open(inode, file);
+	/* put watchdog in service state */
+	iowrite32(WDKEY_SEQ0, davinci_wdt->base + WDTCR);
+	/* put watchdog in active state */
+	iowrite32(WDKEY_SEQ1, davinci_wdt->base + WDTCR);
+	return 0;
 }
 
-static ssize_t
-davinci_wdt_write(struct file *file, const char *data, size_t len,
-		  loff_t *ppos)
+static unsigned int davinci_wdt_get_timeleft(struct watchdog_device *wdd)
 {
-	if (len)
-		wdt_service();
+	u64 timer_counter;
+	unsigned long freq;
+	u32 val;
+	struct davinci_wdt_device *davinci_wdt = watchdog_get_drvdata(wdd);
 
-	return len;
-}
+	/* if timeout has occured then return 0 */
+	val = ioread32(davinci_wdt->base + WDTCR);
+	if (val & WDFLAG)
+		return 0;
 
-static const struct watchdog_info ident = {
-	.options = WDIOF_KEEPALIVEPING,
-	.identity = "DaVinci Watchdog",
-};
+	freq = clk_get_rate(davinci_wdt->clk);
 
-static long davinci_wdt_ioctl(struct file *file,
-					unsigned int cmd, unsigned long arg)
-{
-	int ret = -ENOTTY;
-
-	switch (cmd) {
-	case WDIOC_GETSUPPORT:
-		ret = copy_to_user((struct watchdog_info *)arg, &ident,
-				   sizeof(ident)) ? -EFAULT : 0;
-		break;
-
-	case WDIOC_GETSTATUS:
-	case WDIOC_GETBOOTSTATUS:
-		ret = put_user(0, (int *)arg);
-		break;
-
-	case WDIOC_KEEPALIVE:
-		wdt_service();
-		ret = 0;
-		break;
-
-	case WDIOC_GETTIMEOUT:
-		ret = put_user(heartbeat, (int *)arg);
-		break;
-	}
-	return ret;
-}
+	if (!freq)
+		return 0;
 
-static int davinci_wdt_release(struct inode *inode, struct file *file)
-{
-	wdt_service();
-	clear_bit(WDT_IN_USE, &wdt_status);
+	timer_counter = ioread32(davinci_wdt->base + TIM12);
+	timer_counter |= ((u64)ioread32(davinci_wdt->base + TIM34) << 32);
 
-	return 0;
+	do_div(timer_counter, freq);
+
+	return wdd->timeout - timer_counter;
 }
 
-static const struct file_operations davinci_wdt_fops = {
-	.owner = THIS_MODULE,
-	.llseek = no_llseek,
-	.write = davinci_wdt_write,
-	.unlocked_ioctl = davinci_wdt_ioctl,
-	.open = davinci_wdt_open,
-	.release = davinci_wdt_release,
+static const struct watchdog_info davinci_wdt_info = {
+	.options = WDIOF_KEEPALIVEPING,
+	.identity = "DaVinci/Keystone Watchdog",
 };
 
-static struct miscdevice davinci_wdt_miscdev = {
-	.minor = WATCHDOG_MINOR,
-	.name = "watchdog",
-	.fops = &davinci_wdt_fops,
+static const struct watchdog_ops davinci_wdt_ops = {
+	.owner		= THIS_MODULE,
+	.start		= davinci_wdt_start,
+	.stop		= davinci_wdt_ping,
+	.ping		= davinci_wdt_ping,
+	.get_timeleft	= davinci_wdt_get_timeleft,
 };
 
 static int davinci_wdt_probe(struct platform_device *pdev)
@@ -204,37 +159,53 @@ static int davinci_wdt_probe(struct platform_device *pdev)
 	int ret = 0;
 	struct device *dev = &pdev->dev;
 	struct resource  *wdt_mem;
+	struct watchdog_device *wdd;
+	struct davinci_wdt_device *davinci_wdt;
+
+	davinci_wdt = devm_kzalloc(dev, sizeof(*davinci_wdt), GFP_KERNEL);
+	if (!davinci_wdt)
+		return -ENOMEM;
 
-	wdt_clk = devm_clk_get(dev, NULL);
-	if (WARN_ON(IS_ERR(wdt_clk)))
-		return PTR_ERR(wdt_clk);
+	davinci_wdt->clk = devm_clk_get(dev, NULL);
+	if (WARN_ON(IS_ERR(davinci_wdt->clk)))
+		return PTR_ERR(davinci_wdt->clk);
 
-	clk_prepare_enable(wdt_clk);
+	clk_prepare_enable(davinci_wdt->clk);
 
-	if (heartbeat < 1 || heartbeat > MAX_HEARTBEAT)
-		heartbeat = DEFAULT_HEARTBEAT;
+	platform_set_drvdata(pdev, davinci_wdt);
 
-	dev_info(dev, "heartbeat %d sec\n", heartbeat);
+	wdd			= &davinci_wdt->wdd;
+	wdd->info		= &davinci_wdt_info;
+	wdd->ops		= &davinci_wdt_ops;
+	wdd->min_timeout	= 1;
+	wdd->max_timeout	= MAX_HEARTBEAT;
+	wdd->timeout		= DEFAULT_HEARTBEAT;
+
+	watchdog_init_timeout(wdd, heartbeat, dev);
+
+	dev_info(dev, "heartbeat %d sec\n", wdd->timeout);
+
+	watchdog_set_drvdata(wdd, davinci_wdt);
+	watchdog_set_nowayout(wdd, 1);
 
 	wdt_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	wdt_base = devm_ioremap_resource(dev, wdt_mem);
-	if (IS_ERR(wdt_base))
-		return PTR_ERR(wdt_base);
+	davinci_wdt->base = devm_ioremap_resource(dev, wdt_mem);
+	if (IS_ERR(davinci_wdt->base))
+		return PTR_ERR(davinci_wdt->base);
 
-	ret = misc_register(&davinci_wdt_miscdev);
-	if (ret < 0) {
-		dev_err(dev, "cannot register misc device\n");
-	} else {
-		set_bit(WDT_DEVICE_INITED, &wdt_status);
-	}
+	ret = watchdog_register_device(wdd);
+	if (ret < 0)
+		dev_err(dev, "cannot register watchdog device\n");
 
 	return ret;
 }
 
 static int davinci_wdt_remove(struct platform_device *pdev)
 {
-	misc_deregister(&davinci_wdt_miscdev);
-	clk_disable_unprepare(wdt_clk);
+	struct davinci_wdt_device *davinci_wdt = platform_get_drvdata(pdev);
+
+	watchdog_unregister_device(&davinci_wdt->wdd);
+	clk_disable_unprepare(davinci_wdt->clk);
 
 	return 0;
 }

drivers/watchdog/dw_wdt.c

@@ -8,7 +8,7 @@
  * 2 of the License, or (at your option) any later version.
  *
  * This file implements a driver for the Synopsys DesignWare watchdog device
- * in the many ARM subsystems. The watchdog has 16 different timeout periods
+ * in the many subsystems. The watchdog has 16 different timeout periods
  * and these are a function of the input clock frequency.
  *
  * The DesignWare watchdog cannot be stopped once it has been started so we

drivers/watchdog/gpio_wdt.c

+/*
+ * Driver for watchdog device controlled through GPIO-line
+ *
+ * Author: 2013, Alexander Shiyan <shc_work@mail.ru>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/notifier.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <linux/watchdog.h>
+
+#define SOFT_TIMEOUT_MIN	1
+#define SOFT_TIMEOUT_DEF	60
+#define SOFT_TIMEOUT_MAX	0xffff
+
+enum {
+	HW_ALGO_TOGGLE,
+	HW_ALGO_LEVEL,
+};
+
+struct gpio_wdt_priv {
+	int			gpio;
+	bool			active_low;
+	bool			state;
+	unsigned int		hw_algo;
+	unsigned int		hw_margin;
+	unsigned long		last_jiffies;
+	struct notifier_block	notifier;
+	struct timer_list	timer;
+	struct watchdog_device	wdd;
+};
+
+static void gpio_wdt_disable(struct gpio_wdt_priv *priv)
+{
+	gpio_set_value_cansleep(priv->gpio, !priv->active_low);
+
+	/* Put GPIO back to tristate */
+	if (priv->hw_algo == HW_ALGO_TOGGLE)
+		gpio_direction_input(priv->gpio);
+}
+
+static int gpio_wdt_start(struct watchdog_device *wdd)
+{
+	struct gpio_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	priv->state = priv->active_low;
+	gpio_direction_output(priv->gpio, priv->state);
+	priv->last_jiffies = jiffies;
+	mod_timer(&priv->timer, priv->last_jiffies + priv->hw_margin);
+
+	return 0;
+}
+
+static int gpio_wdt_stop(struct watchdog_device *wdd)
+{
+	struct gpio_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	mod_timer(&priv->timer, 0);
+	gpio_wdt_disable(priv);
+
+	return 0;
+}
+
+static int gpio_wdt_ping(struct watchdog_device *wdd)
+{
+	struct gpio_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	priv->last_jiffies = jiffies;
+
+	return 0;
+}
+
+static int gpio_wdt_set_timeout(struct watchdog_device *wdd, unsigned int t)
+{
+	wdd->timeout = t;
+
+	return gpio_wdt_ping(wdd);
+}
+
+static void gpio_wdt_hwping(unsigned long data)
+{
+	struct watchdog_device *wdd = (struct watchdog_device *)data;
+	struct gpio_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	if (time_after(jiffies, priv->last_jiffies +
+		       msecs_to_jiffies(wdd->timeout * 1000))) {
+		dev_crit(wdd->dev, "Timer expired. System will reboot soon!\n");
+		return;
+	}
+
+	/* Restart timer */
+	mod_timer(&priv->timer, jiffies + priv->hw_margin);
+
+	switch (priv->hw_algo) {
+	case HW_ALGO_TOGGLE:
+		/* Toggle output pin */
+		priv->state = !priv->state;
+		gpio_set_value_cansleep(priv->gpio, priv->state);
+		break;
+	case HW_ALGO_LEVEL:
+		/* Pulse */
+		gpio_set_value_cansleep(priv->gpio, !priv->active_low);
+		udelay(1);
+		gpio_set_value_cansleep(priv->gpio, priv->active_low);
+		break;
+	}
+}
+
+static int gpio_wdt_notify_sys(struct notifier_block *nb, unsigned long code,
+			       void *unused)
+{
+	struct gpio_wdt_priv *priv = container_of(nb, struct gpio_wdt_priv,
+						  notifier);
+
+	mod_timer(&priv->timer, 0);
+
+	switch (code) {
+	case SYS_HALT:
+	case SYS_POWER_OFF:
+		gpio_wdt_disable(priv);
+		break;
+	default:
+		break;
+	}
+
+	return NOTIFY_DONE;
+}
+
+static const struct watchdog_info gpio_wdt_ident = {
+	.options	= WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
+			  WDIOF_SETTIMEOUT,
+	.identity	= "GPIO Watchdog",
+};
+
+static const struct watchdog_ops gpio_wdt_ops = {
+	.owner		= THIS_MODULE,
+	.start		= gpio_wdt_start,
+	.stop		= gpio_wdt_stop,
+	.ping		= gpio_wdt_ping,
+	.set_timeout	= gpio_wdt_set_timeout,
+};
+
+static int gpio_wdt_probe(struct platform_device *pdev)
+{
+	struct gpio_wdt_priv *priv;
+	enum of_gpio_flags flags;
+	unsigned int hw_margin;
+	unsigned long f = 0;
+	const char *algo;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->gpio = of_get_gpio_flags(pdev->dev.of_node, 0, &flags);
+	if (!gpio_is_valid(priv->gpio))
+		return priv->gpio;
+
+	priv->active_low = flags & OF_GPIO_ACTIVE_LOW;
+
+	ret = of_property_read_string(pdev->dev.of_node, "hw_algo", &algo);
+	if (ret)
+		return ret;
+	if (!strncmp(algo, "toggle", 6)) {
+		priv->hw_algo = HW_ALGO_TOGGLE;
+		f = GPIOF_IN;
+	} else if (!strncmp(algo, "level", 5)) {
+		priv->hw_algo = HW_ALGO_LEVEL;
+		f = priv->active_low ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+	} else {
+		return -EINVAL;
+	}
+
+	ret = devm_gpio_request_one(&pdev->dev, priv->gpio, f,
+				    dev_name(&pdev->dev));
+	if (ret)
+		return ret;
+
+	ret = of_property_read_u32(pdev->dev.of_node,
+				   "hw_margin_ms", &hw_margin);
+	if (ret)
+		return ret;
+	/* Disallow values lower than 2 and higher than 65535 ms */
+	if (hw_margin < 2 || hw_margin > 65535)
+		return -EINVAL;
+
+	/* Use safe value (1/2 of real timeout) */
+	priv->hw_margin = msecs_to_jiffies(hw_margin / 2);
+
+	watchdog_set_drvdata(&priv->wdd, priv);
+
+	priv->wdd.info		= &gpio_wdt_ident;
+	priv->wdd.ops		= &gpio_wdt_ops;
+	priv->wdd.min_timeout	= SOFT_TIMEOUT_MIN;
+	priv->wdd.max_timeout	= SOFT_TIMEOUT_MAX;
+
+	if (watchdog_init_timeout(&priv->wdd, 0, &pdev->dev) < 0)
+		priv->wdd.timeout = SOFT_TIMEOUT_DEF;
+
+	setup_timer(&priv->timer, gpio_wdt_hwping, (unsigned long)&priv->wdd);
+
+	ret = watchdog_register_device(&priv->wdd);
+	if (ret)
+		return ret;
+
+	priv->notifier.notifier_call = gpio_wdt_notify_sys;
+	ret = register_reboot_notifier(&priv->notifier);
+	if (ret)
+		watchdog_unregister_device(&priv->wdd);
+
+	return ret;
+}
+
+static int gpio_wdt_remove(struct platform_device *pdev)
+{
+	struct gpio_wdt_priv *priv = platform_get_drvdata(pdev);
+
+	del_timer_sync(&priv->timer);
+	unregister_reboot_notifier(&priv->notifier);
+	watchdog_unregister_device(&priv->wdd);
+
+	return 0;
+}
+
+static const struct of_device_id gpio_wdt_dt_ids[] = {
+	{ .compatible = "linux,wdt-gpio", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, gpio_wdt_dt_ids);
+
+static struct platform_driver gpio_wdt_driver = {
+	.driver	= {
+		.name		= "gpio-wdt",
+		.owner		= THIS_MODULE,
+		.of_match_table	= gpio_wdt_dt_ids,
+	},
+	.probe	= gpio_wdt_probe,
+	.remove	= gpio_wdt_remove,
+};
+module_platform_driver(gpio_wdt_driver);
+
+MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>");
+MODULE_DESCRIPTION("GPIO Watchdog");
+MODULE_LICENSE("GPL");

drivers/watchdog/hpwdt.c

@@ -39,7 +39,7 @@
 #endif /* CONFIG_HPWDT_NMI_DECODING */
 #include <asm/nmi.h>
 
-#define HPWDT_VERSION			"1.3.2"
+#define HPWDT_VERSION			"1.3.3"
 #define SECS_TO_TICKS(secs)		((secs) * 1000 / 128)
 #define TICKS_TO_SECS(ticks)		((ticks) * 128 / 1000)
 #define HPWDT_MAX_TIMER			TICKS_TO_SECS(65535)
@@ -55,7 +55,7 @@ static void __iomem *pci_mem_addr;		/* the PCI-memory address */
 static unsigned long __iomem *hpwdt_timer_reg;
 static unsigned long __iomem *hpwdt_timer_con;
 
-static DEFINE_PCI_DEVICE_TABLE(hpwdt_devices) = {
+static const struct pci_device_id hpwdt_devices[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_COMPAQ, 0xB203) },	/* iLO2 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_HP, 0x3306) },	/* iLO3 */
 	{0},			/* terminate list */
@@ -501,8 +501,13 @@ static int hpwdt_pretimeout(unsigned int ulReason, struct pt_regs *regs)
 				"but unable to determine source.\n");
 		}
 	}
-	panic("An NMI occurred, please see the Integrated "
-		"Management Log for details.\n");
+	panic("An NMI occurred. Depending on your system the reason "
+		"for the NMI is logged in any one of the following "
+		"resources:\n"
+		"1. Integrated Management Log (IML)\n"
+		"2. OA Syslog\n"
+		"3. OA Forward Progress Log\n"
+		"4. iLO Event Log");
 
 out:
 	return NMI_DONE;

drivers/watchdog/i6300esb.c

@@ -334,7 +334,7 @@ static struct miscdevice esb_miscdev = {
 /*
  * Data for PCI driver interface
  */
-static DEFINE_PCI_DEVICE_TABLE(esb_pci_tbl) = {
+static const struct pci_device_id esb_pci_tbl[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_9), },
 	{ 0, },                 /* End of list */
 };

drivers/watchdog/imx2_wdt.c

@@ -2,6 +2,7 @@
  * Watchdog driver for IMX2 and later processors
  *
  *  Copyright (C) 2010 Wolfram Sang, Pengutronix e.K. <w.sang@pengutronix.de>
+ *  Copyright (C) 2014 Freescale Semiconductor, Inc.
  *
  * some parts adapted by similar drivers from Darius Augulis and Vladimir
  * Zapolskiy, additional improvements by Wim Van Sebroeck.
@@ -40,6 +41,7 @@
 #define IMX2_WDT_WCR_WT		(0xFF << 8)	/* -> Watchdog Timeout Field */
 #define IMX2_WDT_WCR_WRE	(1 << 3)	/* -> WDOG Reset Enable */
 #define IMX2_WDT_WCR_WDE	(1 << 2)	/* -> Watchdog Enable */
+#define IMX2_WDT_WCR_WDZST	(1 << 0)	/* -> Watchdog timer Suspend */
 
 #define IMX2_WDT_WSR		0x02		/* Service Register */
 #define IMX2_WDT_SEQ1		0x5555		/* -> service sequence 1 */
@@ -87,6 +89,8 @@ static inline void imx2_wdt_setup(void)
 {
 	u16 val = __raw_readw(imx2_wdt.base + IMX2_WDT_WCR);
 
+	/* Suspend timer in low power mode, write once-only */
+	val |= IMX2_WDT_WCR_WDZST;
 	/* Strip the old watchdog Time-Out value */
 	val &= ~IMX2_WDT_WCR_WT;
 	/* Generate reset if WDOG times out */

drivers/watchdog/moxart_wdt.c

@@ -19,6 +19,8 @@
 #include <linux/watchdog.h>
 #include <linux/moduleparam.h>
 
+#include <asm/system_misc.h>
+
 #define REG_COUNT			0x4
 #define REG_MODE			0x8
 #define REG_ENABLE			0xC
@@ -29,8 +31,17 @@ struct moxart_wdt_dev {
 	unsigned int clock_frequency;
 };
 
+static struct moxart_wdt_dev *moxart_restart_ctx;
+
 static int heartbeat;
 
+static void moxart_wdt_restart(enum reboot_mode reboot_mode, const char *cmd)
+{
+	writel(1, moxart_restart_ctx->base + REG_COUNT);
+	writel(0x5ab9, moxart_restart_ctx->base + REG_MODE);
+	writel(0x03, moxart_restart_ctx->base + REG_ENABLE);
+}
+
 static int moxart_wdt_stop(struct watchdog_device *wdt_dev)
 {
 	struct moxart_wdt_dev *moxart_wdt = watchdog_get_drvdata(wdt_dev);
@@ -125,6 +136,9 @@ static int moxart_wdt_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
+	moxart_restart_ctx = moxart_wdt;
+	arm_pm_restart = moxart_wdt_restart;
+
 	dev_dbg(dev, "Watchdog enabled (heartbeat=%d sec, nowayout=%d)\n",
 		moxart_wdt->dev.timeout, nowayout);
 
@@ -135,6 +149,7 @@ static int moxart_wdt_remove(struct platform_device *pdev)
 {
 	struct moxart_wdt_dev *moxart_wdt = platform_get_drvdata(pdev);
 
+	arm_pm_restart = NULL;
 	moxart_wdt_stop(&moxart_wdt->dev);
 	watchdog_unregister_device(&moxart_wdt->dev);
 

drivers/watchdog/mpc8xxx_wdt.c

@@ -73,9 +73,7 @@ MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started "
  * to 0
  */
 static int prescale = 1;
-static unsigned int timeout_sec;
 
-static unsigned long wdt_is_open;
 static DEFINE_SPINLOCK(wdt_spinlock);
 
 static void mpc8xxx_wdt_keepalive(void)
@@ -87,39 +85,23 @@ static void mpc8xxx_wdt_keepalive(void)
 	spin_unlock(&wdt_spinlock);
 }
 
+static struct watchdog_device mpc8xxx_wdt_dev;
 static void mpc8xxx_wdt_timer_ping(unsigned long arg);
-static DEFINE_TIMER(wdt_timer, mpc8xxx_wdt_timer_ping, 0, 0);
+static DEFINE_TIMER(wdt_timer, mpc8xxx_wdt_timer_ping, 0,
+		(unsigned long)&mpc8xxx_wdt_dev);
 
 static void mpc8xxx_wdt_timer_ping(unsigned long arg)
 {
+	struct watchdog_device *w = (struct watchdog_device *)arg;
+
 	mpc8xxx_wdt_keepalive();
 	/* We're pinging it twice faster than needed, just to be sure. */
-	mod_timer(&wdt_timer, jiffies + HZ * timeout_sec / 2);
-}
-
-static void mpc8xxx_wdt_pr_warn(const char *msg)
-{
-	pr_crit("%s, expect the %s soon!\n", msg,
-		reset ? "reset" : "machine check exception");
+	mod_timer(&wdt_timer, jiffies + HZ * w->timeout / 2);
 }
 
-static ssize_t mpc8xxx_wdt_write(struct file *file, const char __user *buf,
-				 size_t count, loff_t *ppos)
-{
-	if (count)
-		mpc8xxx_wdt_keepalive();
-	return count;
-}
-
-static int mpc8xxx_wdt_open(struct inode *inode, struct file *file)
+static int mpc8xxx_wdt_start(struct watchdog_device *w)
 {
 	u32 tmp = SWCRR_SWEN;
-	if (test_and_set_bit(0, &wdt_is_open))
-		return -EBUSY;
-
-	/* Once we start the watchdog we can't stop it */
-	if (nowayout)
-		__module_get(THIS_MODULE);
 
 	/* Good, fire up the show */
 	if (prescale)
@@ -133,59 +115,37 @@ static int mpc8xxx_wdt_open(struct inode *inode, struct file *file)
 
 	del_timer_sync(&wdt_timer);
 
-	return nonseekable_open(inode, file);
+	return 0;
 }
 
-static int mpc8xxx_wdt_release(struct inode *inode, struct file *file)
+static int mpc8xxx_wdt_ping(struct watchdog_device *w)
 {
-	if (!nowayout)
-		mpc8xxx_wdt_timer_ping(0);
-	else
-		mpc8xxx_wdt_pr_warn("watchdog closed");
-	clear_bit(0, &wdt_is_open);
+	mpc8xxx_wdt_keepalive();
 	return 0;
 }
 
-static long mpc8xxx_wdt_ioctl(struct file *file, unsigned int cmd,
-							unsigned long arg)
+static int mpc8xxx_wdt_stop(struct watchdog_device *w)
 {
-	void __user *argp = (void __user *)arg;
-	int __user *p = argp;
-	static const struct watchdog_info ident = {
-		.options = WDIOF_KEEPALIVEPING,
-		.firmware_version = 1,
-		.identity = "MPC8xxx",
-	};
-
-	switch (cmd) {
-	case WDIOC_GETSUPPORT:
-		return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
-	case WDIOC_GETSTATUS:
-	case WDIOC_GETBOOTSTATUS:
-		return put_user(0, p);
-	case WDIOC_KEEPALIVE:
-		mpc8xxx_wdt_keepalive();
-		return 0;
-	case WDIOC_GETTIMEOUT:
-		return put_user(timeout_sec, p);
-	default:
-		return -ENOTTY;
-	}
+	mod_timer(&wdt_timer, jiffies);
+	return 0;
 }
 
-static const struct file_operations mpc8xxx_wdt_fops = {
-	.owner		= THIS_MODULE,
-	.llseek		= no_llseek,
-	.write		= mpc8xxx_wdt_write,
-	.unlocked_ioctl	= mpc8xxx_wdt_ioctl,
-	.open		= mpc8xxx_wdt_open,
-	.release	= mpc8xxx_wdt_release,
+static struct watchdog_info mpc8xxx_wdt_info = {
+	.options = WDIOF_KEEPALIVEPING,
+	.firmware_version = 1,
+	.identity = "MPC8xxx",
 };
 
-static struct miscdevice mpc8xxx_wdt_miscdev = {
-	.minor	= WATCHDOG_MINOR,
-	.name	= "watchdog",
-	.fops	= &mpc8xxx_wdt_fops,
+static struct watchdog_ops mpc8xxx_wdt_ops = {
+	.owner = THIS_MODULE,
+	.start = mpc8xxx_wdt_start,
+	.ping = mpc8xxx_wdt_ping,
+	.stop = mpc8xxx_wdt_stop,
+};
+
+static struct watchdog_device mpc8xxx_wdt_dev = {
+	.info = &mpc8xxx_wdt_info,
+	.ops = &mpc8xxx_wdt_ops,
 };
 
 static const struct of_device_id mpc8xxx_wdt_match[];
@@ -197,6 +157,7 @@ static int mpc8xxx_wdt_probe(struct platform_device *ofdev)
 	const struct mpc8xxx_wdt_type *wdt_type;
 	u32 freq = fsl_get_sys_freq();
 	bool enabled;
+	unsigned int timeout_sec;
 
 	match = of_match_device(mpc8xxx_wdt_match, &ofdev->dev);
 	if (!match)
@@ -223,6 +184,7 @@ static int mpc8xxx_wdt_probe(struct platform_device *ofdev)
 	else
 		timeout_sec = timeout / freq;
 
+	mpc8xxx_wdt_dev.timeout = timeout_sec;
 #ifdef MODULE
 	ret = mpc8xxx_wdt_init_late();
 	if (ret)
@@ -238,7 +200,7 @@ static int mpc8xxx_wdt_probe(struct platform_device *ofdev)
 	 * userspace handles it.
 	 */
 	if (enabled)
-		mpc8xxx_wdt_timer_ping(0);
+		mod_timer(&wdt_timer, jiffies);
 	return 0;
 err_unmap:
 	iounmap(wd_base);
@@ -248,9 +210,10 @@ static int mpc8xxx_wdt_probe(struct platform_device *ofdev)
 
 static int mpc8xxx_wdt_remove(struct platform_device *ofdev)
 {
-	mpc8xxx_wdt_pr_warn("watchdog removed");
+	pr_crit("Watchdog removed, expect the %s soon!\n",
+		reset ? "reset" : "machine check exception");
 	del_timer_sync(&wdt_timer);
-	misc_deregister(&mpc8xxx_wdt_miscdev);
+	watchdog_unregister_device(&mpc8xxx_wdt_dev);
 	iounmap(wd_base);
 
 	return 0;
@@ -302,10 +265,11 @@ static int mpc8xxx_wdt_init_late(void)
 	if (!wd_base)
 		return -ENODEV;
 
-	ret = misc_register(&mpc8xxx_wdt_miscdev);
+	watchdog_set_nowayout(&mpc8xxx_wdt_dev, nowayout);
+
+	ret = watchdog_register_device(&mpc8xxx_wdt_dev);
 	if (ret) {
-		pr_err("cannot register miscdev on minor=%d (err=%d)\n",
-		       WATCHDOG_MINOR, ret);
+		pr_err("cannot register watchdog device (err=%d)\n", ret);
 		return ret;
 	}
 	return 0;

drivers/watchdog/nv_tco.c

@@ -289,7 +289,7 @@ static struct miscdevice nv_tco_miscdev = {
  * register a pci_driver, because someone else might one day
  * want to register another driver on the same PCI id.
  */
-static DEFINE_PCI_DEVICE_TABLE(tco_pci_tbl) = {
+static const struct pci_device_id tco_pci_tbl[] = {
 	{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SMBUS,
 	  PCI_ANY_ID, PCI_ANY_ID, },
 	{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SMBUS,

drivers/watchdog/pcwd_pci.c

@@ -801,7 +801,7 @@ static void pcipcwd_card_exit(struct pci_dev *pdev)
 	cards_found--;
 }
 
-static DEFINE_PCI_DEVICE_TABLE(pcipcwd_pci_tbl) = {
+static const struct pci_device_id pcipcwd_pci_tbl[] = {
 	{ PCI_VENDOR_ID_QUICKLOGIC, PCI_DEVICE_ID_WATCHDOG_PCIPCWD,
 		PCI_ANY_ID, PCI_ANY_ID, },
 	{ 0 },			/* End of list */

drivers/watchdog/sirfsoc_wdt.c

@@ -212,7 +212,7 @@ static struct platform_driver sirfsoc_wdt_driver = {
 		.name = "sirfsoc-wdt",
 		.owner = THIS_MODULE,
 		.pm = &sirfsoc_wdt_pm_ops,
-		.of_match_table	= of_match_ptr(sirfsoc_wdt_of_match),
+		.of_match_table	= sirfsoc_wdt_of_match,
 	},
 	.probe = sirfsoc_wdt_probe,
 	.remove = sirfsoc_wdt_remove,

drivers/watchdog/sp5100_tco.c

@@ -303,7 +303,7 @@ static struct miscdevice sp5100_tco_miscdev = {
  * register a pci_driver, because someone else might
  * want to register another driver on the same PCI id.
  */
-static DEFINE_PCI_DEVICE_TABLE(sp5100_tco_pci_tbl) = {
+static const struct pci_device_id sp5100_tco_pci_tbl[] = {
 	{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, PCI_ANY_ID,
 	  PCI_ANY_ID, },
 	{ 0, },			/* End of list */

drivers/watchdog/via_wdt.c

@@ -239,7 +239,7 @@ static void wdt_remove(struct pci_dev *pdev)
 	pci_disable_device(pdev);
 }
 
-static DEFINE_PCI_DEVICE_TABLE(wdt_pci_table) = {
+static const struct pci_device_id wdt_pci_table[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_CX700) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VX800) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VX855) },

drivers/watchdog/w83627hf_wdt.c

@@ -44,10 +44,13 @@
 #define WATCHDOG_NAME "w83627hf/thf/hg/dhg WDT"
 #define WATCHDOG_TIMEOUT 60		/* 60 sec default timeout */
 
-/* You must set this - there is no sane way to probe for this board. */
-static int wdt_io = 0x2E;
-module_param(wdt_io, int, 0);
-MODULE_PARM_DESC(wdt_io, "w83627hf/thf WDT io port (default 0x2E)");
+static int wdt_io;
+static int cr_wdt_timeout;	/* WDT timeout register */
+static int cr_wdt_control;	/* WDT control register */
+
+enum chips { w83627hf, w83627s, w83697hf, w83697ug, w83637hf, w83627thf,
+	     w83687thf, w83627ehf, w83627dhg, w83627uhg, w83667hg, w83627dhg_p,
+	     w83667hg_b, nct6775, nct6776, nct6779 };
 
 static int timeout;			/* in seconds */
 module_param(timeout, int, 0);
@@ -72,6 +75,29 @@ MODULE_PARM_DESC(nowayout,
 
 #define W83627HF_LD_WDT		0x08
 
+#define W83627HF_ID		0x52
+#define W83627S_ID		0x59
+#define W83697HF_ID		0x60
+#define W83697UG_ID		0x68
+#define W83637HF_ID		0x70
+#define W83627THF_ID		0x82
+#define W83687THF_ID		0x85
+#define W83627EHF_ID		0x88
+#define W83627DHG_ID		0xa0
+#define W83627UHG_ID		0xa2
+#define W83667HG_ID		0xa5
+#define W83627DHG_P_ID		0xb0
+#define W83667HG_B_ID		0xb3
+#define NCT6775_ID		0xb4
+#define NCT6776_ID		0xc3
+#define NCT6779_ID		0xc5
+
+#define W83627HF_WDT_TIMEOUT	0xf6
+#define W83697HF_WDT_TIMEOUT	0xf4
+
+#define W83627HF_WDT_CONTROL	0xf5
+#define W83697HF_WDT_CONTROL	0xf3
+
 static void superio_outb(int reg, int val)
 {
 	outb(reg, WDT_EFER);
@@ -106,10 +132,7 @@ static void superio_exit(void)
 	release_region(wdt_io, 2);
 }
 
-/* tyan motherboards seem to set F5 to 0x4C ?
- * So explicitly init to appropriate value. */
-
-static int w83627hf_init(struct watchdog_device *wdog)
+static int w83627hf_init(struct watchdog_device *wdog, enum chips chip)
 {
 	int ret;
 	unsigned char t;
@@ -119,35 +142,83 @@ static int w83627hf_init(struct watchdog_device *wdog)
 		return ret;
 
 	superio_select(W83627HF_LD_WDT);
-	t = superio_inb(0x20);	/* check chip version	*/
-	if (t == 0x82) {	/* W83627THF		*/
-		t = (superio_inb(0x2b) & 0xf7);
-		superio_outb(0x2b, t | 0x04); /* set GPIO3 to WDT0 */
-	} else if (t == 0x88 || t == 0xa0) {	/* W83627EHF / W83627DHG */
-		t = superio_inb(0x2d);
-		superio_outb(0x2d, t & ~0x01);	/* set GPIO5 to WDT0 */
-	}
 
 	/* set CR30 bit 0 to activate GPIO2 */
 	t = superio_inb(0x30);
 	if (!(t & 0x01))
 		superio_outb(0x30, t | 0x01);
 
-	t = superio_inb(0xF6);
+	switch (chip) {
+	case w83627hf:
+	case w83627s:
+		t = superio_inb(0x2B) & ~0x10;
+		superio_outb(0x2B, t); /* set GPIO24 to WDT0 */
+		break;
+	case w83697hf:
+		/* Set pin 119 to WDTO# mode (= CR29, WDT0) */
+		t = superio_inb(0x29) & ~0x60;
+		t |= 0x20;
+		superio_outb(0x29, t);
+		break;
+	case w83697ug:
+		/* Set pin 118 to WDTO# mode */
+		t = superio_inb(0x2b) & ~0x04;
+		superio_outb(0x2b, t);
+		break;
+	case w83627thf:
+		t = (superio_inb(0x2B) & ~0x08) | 0x04;
+		superio_outb(0x2B, t); /* set GPIO3 to WDT0 */
+		break;
+	case w83627dhg:
+	case w83627dhg_p:
+		t = superio_inb(0x2D) & ~0x01; /* PIN77 -> WDT0# */
+		superio_outb(0x2D, t); /* set GPIO5 to WDT0 */
+		t = superio_inb(cr_wdt_control);
+		t |= 0x02;	/* enable the WDTO# output low pulse
+				 * to the KBRST# pin */
+		superio_outb(cr_wdt_control, t);
+		break;
+	case w83637hf:
+		break;
+	case w83687thf:
+		t = superio_inb(0x2C) & ~0x80; /* PIN47 -> WDT0# */
+		superio_outb(0x2C, t);
+		break;
+	case w83627ehf:
+	case w83627uhg:
+	case w83667hg:
+	case w83667hg_b:
+	case nct6775:
+	case nct6776:
+	case nct6779:
+		/*
+		 * These chips have a fixed WDTO# output pin (W83627UHG),
+		 * or support more than one WDTO# output pin.
+		 * Don't touch its configuration, and hope the BIOS
+		 * does the right thing.
+		 */
+		t = superio_inb(cr_wdt_control);
+		t |= 0x02;	/* enable the WDTO# output low pulse
+				 * to the KBRST# pin */
+		superio_outb(cr_wdt_control, t);
+		break;
+	default:
+		break;
+	}
+
+	t = superio_inb(cr_wdt_timeout);
 	if (t != 0) {
 		pr_info("Watchdog already running. Resetting timeout to %d sec\n",
 			wdog->timeout);
-		superio_outb(0xF6, wdog->timeout);
+		superio_outb(cr_wdt_timeout, wdog->timeout);
 	}
 
 	/* set second mode & disable keyboard turning off watchdog */
-	t = superio_inb(0xF5) & ~0x0C;
-	/* enable the WDTO# output low pulse to the KBRST# pin */
-	t |= 0x02;
-	superio_outb(0xF5, t);
+	t = superio_inb(cr_wdt_control) & ~0x0C;
+	superio_outb(cr_wdt_control, t);
 
-	/* disable keyboard & mouse turning off watchdog */
-	t = superio_inb(0xF7) & ~0xC0;
+	/* reset trigger, disable keyboard & mouse turning off watchdog */
+	t = superio_inb(0xF7) & ~0xD0;
 	superio_outb(0xF7, t);
 
 	superio_exit();
@@ -164,7 +235,7 @@ static int wdt_set_time(unsigned int timeout)
 		return ret;
 
 	superio_select(W83627HF_LD_WDT);
-	superio_outb(0xF6, timeout);
+	superio_outb(cr_wdt_timeout, timeout);
 	superio_exit();
 
 	return 0;
@@ -197,7 +268,7 @@ static unsigned int wdt_get_time(struct watchdog_device *wdog)
 		return 0;
 
 	superio_select(W83627HF_LD_WDT);
-	timeleft = superio_inb(0xF6);
+	timeleft = superio_inb(cr_wdt_timeout);
 	superio_exit();
 
 	return timeleft;
@@ -249,16 +320,123 @@ static struct notifier_block wdt_notifier = {
 	.notifier_call = wdt_notify_sys,
 };
 
+static int wdt_find(int addr)
+{
+	u8 val;
+	int ret;
+
+	cr_wdt_timeout = W83627HF_WDT_TIMEOUT;
+	cr_wdt_control = W83627HF_WDT_CONTROL;
+
+	ret = superio_enter();
+	if (ret)
+		return ret;
+	superio_select(W83627HF_LD_WDT);
+	val = superio_inb(0x20);
+	switch (val) {
+	case W83627HF_ID:
+		ret = w83627hf;
+		break;
+	case W83627S_ID:
+		ret = w83627s;
+		break;
+	case W83697HF_ID:
+		ret = w83697hf;
+		cr_wdt_timeout = W83697HF_WDT_TIMEOUT;
+		cr_wdt_control = W83697HF_WDT_CONTROL;
+		break;
+	case W83697UG_ID:
+		ret = w83697ug;
+		cr_wdt_timeout = W83697HF_WDT_TIMEOUT;
+		cr_wdt_control = W83697HF_WDT_CONTROL;
+		break;
+	case W83637HF_ID:
+		ret = w83637hf;
+		break;
+	case W83627THF_ID:
+		ret = w83627thf;
+		break;
+	case W83687THF_ID:
+		ret = w83687thf;
+		break;
+	case W83627EHF_ID:
+		ret = w83627ehf;
+		break;
+	case W83627DHG_ID:
+		ret = w83627dhg;
+		break;
+	case W83627DHG_P_ID:
+		ret = w83627dhg_p;
+		break;
+	case W83627UHG_ID:
+		ret = w83627uhg;
+		break;
+	case W83667HG_ID:
+		ret = w83667hg;
+		break;
+	case W83667HG_B_ID:
+		ret = w83667hg_b;
+		break;
+	case NCT6775_ID:
+		ret = nct6775;
+		break;
+	case NCT6776_ID:
+		ret = nct6776;
+		break;
+	case NCT6779_ID:
+		ret = nct6779;
+		break;
+	case 0xff:
+		ret = -ENODEV;
+		break;
+	default:
+		ret = -ENODEV;
+		pr_err("Unsupported chip ID: 0x%02x\n", val);
+		break;
+	}
+	superio_exit();
+	return ret;
+}
+
 static int __init wdt_init(void)
 {
 	int ret;
+	int chip;
+	const char * const chip_name[] = {
+		"W83627HF",
+		"W83627S",
+		"W83697HF",
+		"W83697UG",
+		"W83637HF",
+		"W83627THF",
+		"W83687THF",
+		"W83627EHF",
+		"W83627DHG",
+		"W83627UHG",
+		"W83667HG",
+		"W83667DHG-P",
+		"W83667HG-B",
+		"NCT6775",
+		"NCT6776",
+		"NCT6779",
+	};
+
+	wdt_io = 0x2e;
+	chip = wdt_find(0x2e);
+	if (chip < 0) {
+		wdt_io = 0x4e;
+		chip = wdt_find(0x4e);
+		if (chip < 0)
+			return chip;
+	}
 
-	pr_info("WDT driver for the Winbond(TM) W83627HF/THF/HG/DHG Super I/O chip initialising\n");
+	pr_info("WDT driver for %s Super I/O chip initialising\n",
+		chip_name[chip]);
 
 	watchdog_init_timeout(&wdt_dev, timeout, NULL);
 	watchdog_set_nowayout(&wdt_dev, nowayout);
 
-	ret = w83627hf_init(&wdt_dev);
+	ret = w83627hf_init(&wdt_dev, chip);
 	if (ret) {
 		pr_err("failed to initialize watchdog (err=%d)\n", ret);
 		return ret;

drivers/watchdog/watchdog_core.c

@@ -78,7 +78,7 @@ int watchdog_init_timeout(struct watchdog_device *wdd,
 	watchdog_check_min_max_timeout(wdd);
 
 	/* try to get the timeout module parameter first */
-	if (!watchdog_timeout_invalid(wdd, timeout_parm)) {
+	if (!watchdog_timeout_invalid(wdd, timeout_parm) && timeout_parm) {
 		wdd->timeout = timeout_parm;
 		return ret;
 	}
@@ -89,7 +89,7 @@ int watchdog_init_timeout(struct watchdog_device *wdd,
 	if (dev == NULL || dev->of_node == NULL)
 		return ret;
 	of_property_read_u32(dev->of_node, "timeout-sec", &t);
-	if (!watchdog_timeout_invalid(wdd, t))
+	if (!watchdog_timeout_invalid(wdd, t) && t)
 		wdd->timeout = t;
 	else
 		ret = -EINVAL;

drivers/watchdog/wdt_pci.c

@@ -720,7 +720,7 @@ static void wdtpci_remove_one(struct pci_dev *pdev)
 }
 
 
-static DEFINE_PCI_DEVICE_TABLE(wdtpci_pci_tbl) = {
+static const struct pci_device_id wdtpci_pci_tbl[] = {
 	{
 		.vendor	   = PCI_VENDOR_ID_ACCESSIO,
 		.device	   = PCI_DEVICE_ID_ACCESSIO_WDG_CSM,