Commit 1841f613 authored by Martin Langer's avatar Martin Langer Committed by Jaroslav Kysela

[ALSA] Add snd-miro driver

Added snd-miro driver for miroSOUND PCM by Martin Langer.
Signed-off-by: default avatarTakashi Iwai <tiwai@suse.de>
parent cbac4b0c
...@@ -1014,6 +1014,23 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. ...@@ -1014,6 +1014,23 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
The power-management is supported. The power-management is supported.
Module snd-miro
---------------
Module for Miro soundcards: miroSOUND PCM 1 pro,
miroSOUND PCM 12,
miroSOUND PCM 20 Radio.
port - Port # (0x530,0x604,0xe80,0xf40)
irq - IRQ # (5,7,9,10,11)
dma1 - 1st dma # (0,1,3)
dma2 - 2nd dma # (0,1)
mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330)
mpu_irq - MPU-401 irq # (5,7,9,10)
fm_port - FM Port # (0x388)
wss - enable WSS mode
ide - enable onboard ide support
Module snd-mixart Module snd-mixart
----------------- -----------------
......
...@@ -292,6 +292,20 @@ config SND_OPTI93X ...@@ -292,6 +292,20 @@ config SND_OPTI93X
To compile this driver as a module, choose M here: the module To compile this driver as a module, choose M here: the module
will be called snd-opti93x. will be called snd-opti93x.
config SND_MIRO
tristate "Miro miroSOUND PCM1pro/PCM12/PCM20radio driver"
depends on SND
select SND_OPL4_LIB
select SND_CS4231_LIB
select SND_MPU401_UART
select SND_PCM
help
Say 'Y' or 'M' to include support for Miro miroSOUND PCM1 pro,
miroSOUND PCM12 and miroSOUND PCM20 Radio soundcards.
To compile this driver as a module, choose M here: the module
will be called snd-miro.
config SND_SB8 config SND_SB8
tristate "Sound Blaster 1.0/2.0/Pro (8-bit)" tristate "Sound Blaster 1.0/2.0/Pro (8-bit)"
depends on SND depends on SND
......
...@@ -6,8 +6,10 @@ ...@@ -6,8 +6,10 @@
snd-opti92x-ad1848-objs := opti92x-ad1848.o snd-opti92x-ad1848-objs := opti92x-ad1848.o
snd-opti92x-cs4231-objs := opti92x-cs4231.o snd-opti92x-cs4231-objs := opti92x-cs4231.o
snd-opti93x-objs := opti93x.o snd-opti93x-objs := opti93x.o
snd-miro-objs := miro.o
# Toplevel Module Dependency # Toplevel Module Dependency
obj-$(CONFIG_SND_OPTI92X_AD1848) += snd-opti92x-ad1848.o obj-$(CONFIG_SND_OPTI92X_AD1848) += snd-opti92x-ad1848.o
obj-$(CONFIG_SND_OPTI92X_CS4231) += snd-opti92x-cs4231.o obj-$(CONFIG_SND_OPTI92X_CS4231) += snd-opti92x-cs4231.o
obj-$(CONFIG_SND_OPTI93X) += snd-opti93x.o obj-$(CONFIG_SND_OPTI93X) += snd-opti93x.o
obj-$(CONFIG_SND_MIRO) += snd-miro.o
This diff is collapsed.
#ifndef _MIRO_H_
#define _MIRO_H_
#define ACI_REG_COMMAND 0 /* write register offset */
#define ACI_REG_STATUS 1 /* read register offset */
#define ACI_REG_BUSY 2 /* busy register offset */
#define ACI_REG_RDS 2 /* PCM20: RDS register offset */
#define ACI_MINTIME 500 /* ACI time out limit */
#define ACI_SET_MUTE 0x0d
#define ACI_SET_POWERAMP 0x0f
#define ACI_SET_TUNERMUTE 0xa3
#define ACI_SET_TUNERMONO 0xa4
#define ACI_SET_IDE 0xd0
#define ACI_SET_WSS 0xd1
#define ACI_SET_SOLOMODE 0xd2
#define ACI_SET_PREAMP 0x03
#define ACI_GET_PREAMP 0x21
#define ACI_WRITE_TUNE 0xa7
#define ACI_READ_TUNERSTEREO 0xa8
#define ACI_READ_TUNERSTATION 0xa9
#define ACI_READ_VERSION 0xf1
#define ACI_READ_IDCODE 0xf2
#define ACI_INIT 0xff
#define ACI_STATUS 0xf0
#define ACI_S_GENERAL 0x00
#define ACI_ERROR_OP 0xdf
/* ACI Mixer */
/* These are the values for the right channel GET registers.
Add an offset of 0x01 for the left channel register.
(left=right+0x01) */
#define ACI_GET_MASTER 0x03
#define ACI_GET_MIC 0x05
#define ACI_GET_LINE 0x07
#define ACI_GET_CD 0x09
#define ACI_GET_SYNTH 0x0b
#define ACI_GET_PCM 0x0d
#define ACI_GET_LINE1 0x10 /* Radio on PCM20 */
#define ACI_GET_LINE2 0x12
#define ACI_GET_EQ1 0x22 /* from Bass ... */
#define ACI_GET_EQ2 0x24
#define ACI_GET_EQ3 0x26
#define ACI_GET_EQ4 0x28
#define ACI_GET_EQ5 0x2a
#define ACI_GET_EQ6 0x2c
#define ACI_GET_EQ7 0x2e /* ... to Treble */
/* And these are the values for the right channel SET registers.
For left channel access you have to add an offset of 0x08.
MASTER is an exception, which needs an offset of 0x01 */
#define ACI_SET_MASTER 0x00
#define ACI_SET_MIC 0x30
#define ACI_SET_LINE 0x31
#define ACI_SET_CD 0x34
#define ACI_SET_SYNTH 0x33
#define ACI_SET_PCM 0x32
#define ACI_SET_LINE1 0x35 /* Radio on PCM20 */
#define ACI_SET_LINE2 0x36
#define ACI_SET_EQ1 0x40 /* from Bass ... */
#define ACI_SET_EQ2 0x41
#define ACI_SET_EQ3 0x42
#define ACI_SET_EQ4 0x43
#define ACI_SET_EQ5 0x44
#define ACI_SET_EQ6 0x45
#define ACI_SET_EQ7 0x46 /* ... to Treble */
#endif /* _MIRO_H_ */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment