Commit 1af2f618 authored by Arec Kao's avatar Arec Kao Committed by Mauro Carvalho Chehab

media: ov13b10: Support device probe in non-zero ACPI D state

Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.

Also do identification on the first access of the device, whether in
probe or when starting streaming.
Signed-off-by: default avatarArec Kao <arec.kao@intel.com>
Signed-off-by: default avatarSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@kernel.org>
parent 859128ab
......@@ -589,6 +589,9 @@ struct ov13b10 {
/* Streaming on/off */
bool streaming;
/* True if the device has been identified */
bool identified;
};
#define to_ov13b10(_sd) container_of(_sd, struct ov13b10, sd)
......@@ -1023,12 +1026,42 @@ ov13b10_set_pad_format(struct v4l2_subdev *sd,
return 0;
}
/* Verify chip ID */
static int ov13b10_identify_module(struct ov13b10 *ov13b)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
int ret;
u32 val;
if (ov13b->identified)
return 0;
ret = ov13b10_read_reg(ov13b, OV13B10_REG_CHIP_ID,
OV13B10_REG_VALUE_24BIT, &val);
if (ret)
return ret;
if (val != OV13B10_CHIP_ID) {
dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
OV13B10_CHIP_ID, val);
return -EIO;
}
ov13b->identified = true;
return 0;
}
static int ov13b10_start_streaming(struct ov13b10 *ov13b)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
const struct ov13b10_reg_list *reg_list;
int ret, link_freq_index;
ret = ov13b10_identify_module(ov13b);
if (ret)
return ret;
/* Get out of from software reset */
ret = ov13b10_write_reg(ov13b, OV13B10_REG_SOFTWARE_RST,
OV13B10_REG_VALUE_08BIT, OV13B10_SOFTWARE_RST);
......@@ -1144,27 +1177,6 @@ static int __maybe_unused ov13b10_resume(struct device *dev)
return ret;
}
/* Verify chip ID */
static int ov13b10_identify_module(struct ov13b10 *ov13b)
{
struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
int ret;
u32 val;
ret = ov13b10_read_reg(ov13b, OV13B10_REG_CHIP_ID,
OV13B10_REG_VALUE_24BIT, &val);
if (ret)
return ret;
if (val != OV13B10_CHIP_ID) {
dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
OV13B10_CHIP_ID, val);
return -EIO;
}
return 0;
}
static const struct v4l2_subdev_video_ops ov13b10_video_ops = {
.s_stream = ov13b10_set_stream,
};
......@@ -1379,6 +1391,7 @@ static int ov13b10_check_hwcfg(struct device *dev)
static int ov13b10_probe(struct i2c_client *client)
{
struct ov13b10 *ov13b;
bool full_power;
int ret;
/* Check HW config */
......@@ -1395,11 +1408,14 @@ static int ov13b10_probe(struct i2c_client *client)
/* Initialize subdev */
v4l2_i2c_subdev_init(&ov13b->sd, client, &ov13b10_subdev_ops);
/* Check module identity */
ret = ov13b10_identify_module(ov13b);
if (ret) {
dev_err(&client->dev, "failed to find sensor: %d\n", ret);
return ret;
full_power = acpi_dev_state_d0(&client->dev);
if (full_power) {
/* Check module identity */
ret = ov13b10_identify_module(ov13b);
if (ret) {
dev_err(&client->dev, "failed to find sensor: %d\n", ret);
return ret;
}
}
/* Set default mode to max resolution */
......@@ -1431,7 +1447,10 @@ static int ov13b10_probe(struct i2c_client *client)
* Device is already turned on by i2c-core with ACPI domain PM.
* Enable runtime PM and turn off the device.
*/
pm_runtime_set_active(&client->dev);
/* Set the device's state to active if it's in D0 state. */
if (full_power)
pm_runtime_set_active(&client->dev);
pm_runtime_enable(&client->dev);
pm_runtime_idle(&client->dev);
......@@ -1480,6 +1499,7 @@ static struct i2c_driver ov13b10_i2c_driver = {
},
.probe_new = ov13b10_probe,
.remove = ov13b10_remove,
.flags = I2C_DRV_ACPI_WAIVE_D0_PROBE,
};
module_i2c_driver(ov13b10_i2c_driver);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment