Skip to content

L
linux
Commit 1af929c4 authored by Aristeu Sergio Rozanski Filho's avatar Aristeu Sergio Rozanski Filho Committed by James Bottomley
Browse files
Options

[PATCH] qlogicfas: move common definitions to qlogicfas.h

parent a5d98e0c
Hide whitespace changes
Inline Side-by-side
Showing with 114 additions and 105 deletions
drivers/scsi/qlogicfas.c
View file @ 1af929c4
......@@ -38,87 +38,6 @@
are deemed to be part of the source code.
*/
/*----------------------------------------------------------------*/
/* Configuration */
/* Set the following to 2 to use normal interrupt (active high/totempole-
tristate), otherwise use 0 (REQUIRED FOR PCMCIA) for active low, open
drain */
#define QL_INT_ACTIVE_HIGH 2
/* Set the following to max out the speed of the PIO PseudoDMA transfers,
again, 0 tends to be slower, but more stable. */
#define QL_TURBO_PDMA 1
/* This should be 1 to enable parity detection */
#define QL_ENABLE_PARITY 1
/* This will reset all devices when the driver is initialized (during bootup).
The other linux drivers don't do this, but the DOS drivers do, and after
using DOS or some kind of crash or lockup this will bring things back
without requiring a cold boot. It does take some time to recover from a
reset, so it is slower, and I have seen timeouts so that devices weren't
recognized when this was set. */
#define QL_RESET_AT_START 0
/* crystal frequency in megahertz (for offset 5 and 9)
Please set this for your card. Most Qlogic cards are 40 Mhz. The
Control Concepts ISA (not VLB) is 24 Mhz */
#define XTALFREQ 40
/**********/
/* DANGER! modify these at your own risk */
/* SLOWCABLE can usually be reset to zero if you have a clean setup and
proper termination. The rest are for synchronous transfers and other
advanced features if your device can transfer faster than 5Mb/sec.
If you are really curious, email me for a quick howto until I have
something official */
/**********/
/*****/
/* config register 1 (offset 8) options */
/* This needs to be set to 1 if your cabling is long or noisy */
#define SLOWCABLE 1
/*****/
/* offset 0xc */
/* This will set fast (10Mhz) synchronous timing when set to 1
For this to have an effect, FASTCLK must also be 1 */
#define FASTSCSI 0
/* This when set to 1 will set a faster sync transfer rate */
#define FASTCLK 0 /*(XTALFREQ>25?1:0)*/
/*****/
/* offset 6 */
/* This is the sync transfer divisor, XTALFREQ/X will be the maximum
achievable data rate (assuming the rest of the system is capable
and set properly) */
#define SYNCXFRPD 5 /*(XTALFREQ/5)*/
/*****/
/* offset 7 */
/* This is the count of how many synchronous transfers can take place
i.e. how many reqs can occur before an ack is given.
The maximum value for this is 15, the upper bits can modify
REQ/ACK assertion and deassertion during synchronous transfers
If this is 0, the bus will only transfer asynchronously */
#define SYNCOFFST 0
/* for the curious, bits 7&6 control the deassertion delay in 1/2 cycles
of the 40Mhz clock. If FASTCLK is 1, specifying 01 (1/2) will
cause the deassertion to be early by 1/2 clock. Bits 5&4 control
the assertion delay, also in 1/2 clocks (FASTCLK is ignored here). */
/*----------------------------------------------------------------*/
#ifdef PCMCIA
#undef QL_INT_ACTIVE_HIGH
#define QL_INT_ACTIVE_HIGH 0
#endif
#include <linux/module.h>
#include <linux/blkdev.h> /* to get disk capacity */
......@@ -141,35 +60,18 @@
#include "qlogicfas.h"
/*----------------------------------------------------------------*/
/* driver state info, local to driver */
static int qlcfg5 = (XTALFREQ << 5); /* 15625/512 */
static int qlcfg6 = SYNCXFRPD;
static int qlcfg7 = SYNCOFFST;
static int qlcfg8 = (SLOWCABLE << 7) | (QL_ENABLE_PARITY << 4);
static int qlcfg9 = ((XTALFREQ + 4) / 5);
static int qlcfgc = (FASTCLK << 3) | (FASTSCSI << 4);
int qlcfg5 = (XTALFREQ << 5); /* 15625/512 */
int qlcfg6 = SYNCXFRPD;
int qlcfg7 = SYNCOFFST;
int qlcfg8 = (SLOWCABLE << 7) | (QL_ENABLE_PARITY << 4);
int qlcfg9 = ((XTALFREQ + 4) / 5);
int qlcfgc = (FASTCLK << 3) | (FASTSCSI << 4);
static char qlogicfas_name[] = "qlogicfas";
int qlogicfas_queuecommand(Scsi_Cmnd * cmd, void (*done) (Scsi_Cmnd *));
/*----------------------------------------------------------------*/
/* The qlogic card uses two register maps - These macros select which one */
#define REG0 ( outb( inb( qbase + 0xd ) & 0x7f , qbase + 0xd ), outb( 4 , qbase + 0xd ))
#define REG1 ( outb( inb( qbase + 0xd ) | 0x80 , qbase + 0xd ), outb( 0xb4 | QL_INT_ACTIVE_HIGH , qbase + 0xd ))
/* following is watchdog timeout in microseconds */
#define WATCHDOG 5000000
/*----------------------------------------------------------------*/
/* the following will set the monitor border color (useful to find
where something crashed or gets stuck at and as a simple profiler) */
#if 0
#define rtrc(i) {inb(0x3da);outb(0x31,0x3c0);outb((i),0x3c0);}
#else
#define rtrc(i) {}
#endif
/*----------------------------------------------------------------*/
/* local functions */
......@@ -531,7 +433,7 @@ static void ql_ihandl(int irq, void *dev_id, struct pt_regs *regs)
(icmd->scsi_done) (icmd);
}
static irqreturn_t do_ql_ihandl(int irq, void *dev_id, struct pt_regs *regs)
irqreturn_t do_ql_ihandl(int irq, void *dev_id, struct pt_regs *regs)
{
unsigned long flags;
struct Scsi_Host *host = dev_id;
......
drivers/scsi/qlogicfas.h
View file @ 1af929c4
/* to be used by qlogicfas and qlogic_cs */
#ifndef __QLOGICFAS_H
#define __QLOGICFAS_H
/*----------------------------------------------------------------*/
/* Configuration */
/* Set the following to 2 to use normal interrupt (active high/totempole-
tristate), otherwise use 0 (REQUIRED FOR PCMCIA) for active low, open
drain */
#define QL_INT_ACTIVE_HIGH 2
/* Set the following to max out the speed of the PIO PseudoDMA transfers,
again, 0 tends to be slower, but more stable. */
#define QL_TURBO_PDMA 1
/* This should be 1 to enable parity detection */
#define QL_ENABLE_PARITY 1
/* This will reset all devices when the driver is initialized (during bootup).
The other linux drivers don't do this, but the DOS drivers do, and after
using DOS or some kind of crash or lockup this will bring things back
without requiring a cold boot. It does take some time to recover from a
reset, so it is slower, and I have seen timeouts so that devices weren't
recognized when this was set. */
#define QL_RESET_AT_START 0
/* crystal frequency in megahertz (for offset 5 and 9)
Please set this for your card. Most Qlogic cards are 40 Mhz. The
Control Concepts ISA (not VLB) is 24 Mhz */
#define XTALFREQ 40
/**********/
/* DANGER! modify these at your own risk */
/* SLOWCABLE can usually be reset to zero if you have a clean setup and
proper termination. The rest are for synchronous transfers and other
advanced features if your device can transfer faster than 5Mb/sec.
If you are really curious, email me for a quick howto until I have
something official */
/**********/
/*****/
/* config register 1 (offset 8) options */
/* This needs to be set to 1 if your cabling is long or noisy */
#define SLOWCABLE 1
/*****/
/* offset 0xc */
/* This will set fast (10Mhz) synchronous timing when set to 1
For this to have an effect, FASTCLK must also be 1 */
#define FASTSCSI 0
/* This when set to 1 will set a faster sync transfer rate */
#define FASTCLK 0 /*(XTALFREQ>25?1:0)*/
/*****/
/* offset 6 */
/* This is the sync transfer divisor, XTALFREQ/X will be the maximum
achievable data rate (assuming the rest of the system is capable
and set properly) */
#define SYNCXFRPD 5 /*(XTALFREQ/5)*/
/*****/
/* offset 7 */
/* This is the count of how many synchronous transfers can take place
i.e. how many reqs can occur before an ack is given.
The maximum value for this is 15, the upper bits can modify
REQ/ACK assertion and deassertion during synchronous transfers
If this is 0, the bus will only transfer asynchronously */
#define SYNCOFFST 0
/* for the curious, bits 7&6 control the deassertion delay in 1/2 cycles
of the 40Mhz clock. If FASTCLK is 1, specifying 01 (1/2) will
cause the deassertion to be early by 1/2 clock. Bits 5&4 control
the assertion delay, also in 1/2 clocks (FASTCLK is ignored here). */
/*----------------------------------------------------------------*/
#ifdef PCMCIA
#undef QL_INT_ACTIVE_HIGH
#define QL_INT_ACTIVE_HIGH 0
#endif
struct qlogicfas_priv {
int qbase; /* Port */
int qinitid; /* initiator ID */
......@@ -10,5 +93,29 @@ struct qlogicfas_priv {
Scsi_Cmnd *qlcmd; /* current command being processed */
};
typedef struct qlogicfas_priv *qlogicfas_priv_t;
extern int qlcfg5;
extern int qlcfg6;
extern int qlcfg7;
extern int qlcfg8;
extern int qlcfg9;
extern int qlcfgc;
/* The qlogic card uses two register maps - These macros select which one */
#define REG0 ( outb( inb( qbase + 0xd ) & 0x7f , qbase + 0xd ), outb( 4 , qbase + 0xd ))
#define REG1 ( outb( inb( qbase + 0xd ) | 0x80 , qbase + 0xd ), outb( 0xb4 | QL_INT_ACTIVE_HIGH , qbase + 0xd ))
/* following is watchdog timeout in microseconds */
#define WATCHDOG 5000000
/*----------------------------------------------------------------*/
/* the following will set the monitor border color (useful to find
where something crashed or gets stuck at and as a simple profiler) */
#if 0
#define rtrc(i) {inb(0x3da);outb(0x31,0x3c0);outb((i),0x3c0);}
#else
#define rtrc(i) {}
#endif
#endif /* __QLOGICFAS_H */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7