Merge branch 'sh/for-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Provide a FLAT_PLAT_INIT() definition.
  binfmt_flat: Stub in a FLAT_PLAT_INIT().
  video: export sh_mobile_lcdc panel size
  sh: select memchunk size using kernel cmdline
  sh: export sh7723 VEU as VEU2H
  input: migor_ts compile and detection fix
  sh: remove MSTPCR defines from Migo-R header file
  sh: Update sh7763rdp defconfig
  sh: Add support sh7760fb to sh7763rdp board
  sh: Add support sh_eth to sh7763rdp board
  sh: Disable 64kB hugetlbpage size when using 64kB PAGE_SIZE.
  sh: Don't export __{s,u}divsi3_i4i from SH-2 libgcc.
  fix SH7705_CACHE_32KB compilation
  sh: mach-x3proto: Fix up smc91x platform data.

arch/sh/boards/board-ap325rxa.c

@@ -140,6 +140,10 @@ static struct sh_mobile_lcdc_info lcdc_info = {
 			.vsync_len = 1,
 			.sync = 0, /* hsync and vsync are active low */
 		},
+		.lcd_size_cfg = { /* 7.0 inch */
+			.width = 152,
+			.height = 91,
+		},
 		.board_cfg = {
 			.display_on = ap320_wvga_power_on,
 		},

arch/sh/boards/mach-migor/setup.c

@@ -224,6 +224,10 @@ static struct sh_mobile_lcdc_info sh_mobile_lcdc_info = {
 			.vsync_len = 2,
 			.sync = 0,
 		},
+		.lcd_size_cfg = { /* 7.0 inch */
+			.width = 152,
+			.height = 91,
+		},
 	}
 #endif
 #ifdef CONFIG_SH_MIGOR_QVGA
@@ -245,6 +249,10 @@ static struct sh_mobile_lcdc_info sh_mobile_lcdc_info = {
 			.vsync_len = 2,
 			.sync = FB_SYNC_HOR_HIGH_ACT,
 		},
+		.lcd_size_cfg = { /* 2.4 inch */
+			.width = 49,
+			.height = 37,
+		},
 		.board_cfg = {
 			.setup_sys = migor_lcd_qvga_setup,
 		},

arch/sh/boards/mach-sh7763rdp/setup.c

@@ -15,8 +15,11 @@
 #include <linux/interrupt.h>
 #include <linux/input.h>
 #include <linux/mtd/physmap.h>
-#include <asm/io.h>
+#include <linux/fb.h>
+#include <linux/io.h>
 #include <asm/sh7763rdp.h>
+#include <asm/sh_eth.h>
+#include <asm/sh7760fb.h>
 
 /* NOR Flash */
 static struct mtd_partition sh7763rdp_nor_flash_partitions[] = {
@@ -60,8 +63,85 @@ static struct platform_device sh7763rdp_nor_flash_device = {
 	},
 };
 
+/* SH-Ether */
+static struct resource sh_eth_resources[] = {
+	{
+		.start  = 0xFEE00800,   /* use eth1 */
+		.end    = 0xFEE00F7C - 1,
+		.flags  = IORESOURCE_MEM,
+	}, {
+		.start  = 58,   /* irq number */
+		.end    = 58,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct sh_eth_plat_data sh7763_eth_pdata = {
+	.phy = 1,
+	.edmac_endian = EDMAC_LITTLE_ENDIAN,
+};
+
+static struct platform_device sh7763rdp_eth_device = {
+	.name       = "sh-eth",
+	.resource   = sh_eth_resources,
+	.num_resources  = ARRAY_SIZE(sh_eth_resources),
+	.dev        = {
+		.platform_data = &sh7763_eth_pdata,
+	},
+};
+
+/* SH7763 LCDC */
+static struct resource sh7763rdp_fb_resources[] = {
+	{
+		.start  = 0xFFE80000,
+		.end    = 0xFFE80442 - 1,
+		.flags  = IORESOURCE_MEM,
+	},
+};
+
+static struct fb_videomode sh7763fb_videomode = {
+	.refresh = 60,
+	.name = "VGA Monitor",
+	.xres = 640,
+	.yres = 480,
+	.pixclock = 10000,
+	.left_margin = 80,
+	.right_margin = 24,
+	.upper_margin = 30,
+	.lower_margin = 1,
+	.hsync_len = 96,
+	.vsync_len = 1,
+	.sync = 0,
+	.vmode = FB_VMODE_NONINTERLACED,
+	.flag = FBINFO_FLAG_DEFAULT,
+};
+
+static struct sh7760fb_platdata sh7763fb_def_pdata = {
+	.def_mode = &sh7763fb_videomode,
+	.ldmtr = (LDMTR_TFT_COLOR_16|LDMTR_MCNT),
+	.lddfr = LDDFR_16BPP_RGB565,
+	.ldpmmr = 0x0000,
+	.ldpspr = 0xFFFF,
+	.ldaclnr = 0x0001,
+	.ldickr = 0x1102,
+	.rotate = 0,
+	.novsync = 0,
+	.blank = NULL,
+};
+
+static struct platform_device sh7763rdp_fb_device = {
+	.name		= "sh7760-lcdc",
+	.resource	= sh7763rdp_fb_resources,
+	.num_resources = ARRAY_SIZE(sh7763rdp_fb_resources),
+	.dev = {
+		.platform_data = &sh7763fb_def_pdata,
+	},
+};
+
 static struct platform_device *sh7763rdp_devices[] __initdata = {
 	&sh7763rdp_nor_flash_device,
+	&sh7763rdp_eth_device,
+	&sh7763rdp_fb_device,
 };
 
 static int __init sh7763rdp_devices_setup(void)
@@ -69,7 +149,7 @@ static int __init sh7763rdp_devices_setup(void)
 	return platform_add_devices(sh7763rdp_devices,
 				    ARRAY_SIZE(sh7763rdp_devices));
 }
-__initcall(sh7763rdp_devices_setup);
+device_initcall(sh7763rdp_devices_setup);
 
 static void __init sh7763rdp_setup(char **cmdline_p)
 {

arch/sh/boards/mach-x3proto/setup.c

@@ -3,7 +3,7 @@
  *
  * Renesas SH-X3 Prototype Board Support.
  *
- * Copyright (C) 2007 Paul Mundt
+ * Copyright (C) 2007 - 2008 Paul Mundt
  *
  * This file is subject to the terms and conditions of the GNU General Public
  * License.  See the file "COPYING" in the main directory of this archive
@@ -13,6 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/kernel.h>
 #include <linux/io.h>
+#include <linux/smc91x.h>
 #include <asm/ilsel.h>
 
 static struct resource heartbeat_resources[] = {
@@ -30,6 +31,10 @@ static struct platform_device heartbeat_device = {
 	.resource	= heartbeat_resources,
 };
 
+static struct smc91x_platdata smc91x_info = {
+	.flags	= SMC91X_USE_16BIT | SMC91X_NOWAIT,
+};
+
 static struct resource smc91x_resources[] = {
 	[0] = {
 		.start		= 0x18000300,
@@ -47,6 +52,9 @@ static struct platform_device smc91x_device = {
 	.id		= -1,
 	.resource	= smc91x_resources,
 	.num_resources	= ARRAY_SIZE(smc91x_resources),
+	.dev	= {
+		.platform_data = &smc91x_info,
+	},
 };
 
 static struct resource r8a66597_usb_host_resources[] = {

arch/sh/configs/sh7763rdp_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Fri Jun  6 12:20:17 2008
+# Linux kernel version: 2.6.27-rc2
+# Fri Aug  8 13:44:20 2008
 #
 CONFIG_SUPERH=y
 CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
 CONFIG_GENERIC_BUG=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_TIME=y
@@ -19,7 +21,6 @@ CONFIG_LOCKDEP_SUPPORT=y
 # CONFIG_ARCH_HAS_ILOG2_U32 is not set
 # CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_ARCH_NO_VIRT_TO_BUS=y
-CONFIG_ARCH_SUPPORTS_AOUT=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
 
 #
@@ -83,10 +84,16 @@ CONFIG_PROFILING=y
 # CONFIG_MARKERS is not set
 CONFIG_OPROFILE=y
 CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
 # CONFIG_HAVE_KPROBES is not set
 # CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
 # CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
 CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
 CONFIG_SLABINFO=y
 CONFIG_RT_MUTEXES=y
 # CONFIG_TINY_SHMEM is not set
@@ -96,12 +103,13 @@ CONFIG_MODULES=y
 # CONFIG_MODULE_UNLOAD is not set
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
 CONFIG_BLOCK=y
 # CONFIG_LBD is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_LSF is not set
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
 # IO Schedulers
@@ -177,6 +185,7 @@ CONFIG_PAGE_SIZE_4KB=y
 # CONFIG_PAGE_SIZE_8KB is not set
 # CONFIG_PAGE_SIZE_16KB is not set
 # CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
 CONFIG_SELECT_MEMORY_MODEL=y
 # CONFIG_FLATMEM_MANUAL is not set
 # CONFIG_DISCONTIGMEM_MANUAL is not set
@@ -258,6 +267,7 @@ CONFIG_HZ=250
 # CONFIG_SCHED_HRTICK is not set
 # CONFIG_KEXEC is not set
 # CONFIG_CRASH_DUMP is not set
+CONFIG_SECCOMP=y
 CONFIG_PREEMPT_NONE=y
 # CONFIG_PREEMPT_VOLUNTARY is not set
 # CONFIG_PREEMPT is not set
@@ -282,10 +292,6 @@ CONFIG_CMDLINE="console=ttySC2,115200 root=/dev/sda1 rootdelay=10"
 #
 CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
-
-#
-# Networking
-#
 CONFIG_NET=y
 
 #
@@ -361,6 +367,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 #
 # CONFIG_CFG80211 is not set
 CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
 # CONFIG_MAC80211 is not set
 # CONFIG_IEEE80211 is not set
 # CONFIG_RFKILL is not set
@@ -377,6 +384,8 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
 # CONFIG_SYS_HYPERVISOR is not set
 # CONFIG_CONNECTOR is not set
 CONFIG_MTD=y
@@ -471,6 +480,7 @@ CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_RAM is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
 # CONFIG_MISC_DEVICES is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
@@ -515,10 +525,10 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -546,7 +556,9 @@ CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
 # CONFIG_AX88796 is not set
 # CONFIG_STNIC is not set
+CONFIG_SH_ETH=y
 # CONFIG_SMC91X is not set
+# CONFIG_SMC911X is not set
 # CONFIG_IBM_NEW_EMAC_ZMII is not set
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -613,7 +625,11 @@ CONFIG_INPUT=y
 #
 # Character devices
 #
-# CONFIG_VT is not set
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
 CONFIG_DEVKMEM=y
 # CONFIG_SERIAL_NONSTANDARD is not set
 
@@ -644,6 +660,7 @@ CONFIG_HW_RANDOM=y
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
 # CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
 # CONFIG_WATCHDOG is not set
 
 #
@@ -655,6 +672,7 @@ CONFIG_SSB_POSSIBLE=y
 #
 # Multifunction device drivers
 #
+# CONFIG_MFD_CORE is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
 
@@ -679,7 +697,34 @@ CONFIG_SSB_POSSIBLE=y
 #
 # CONFIG_VGASTATE is not set
 # CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+CONFIG_FB_FOREIGN_ENDIAN=y
+CONFIG_FB_BOTH_ENDIAN=y
+# CONFIG_FB_BIG_ENDIAN is not set
+# CONFIG_FB_LITTLE_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_SH_MOBILE_LCDC is not set
+CONFIG_FB_SH7760=y
+# CONFIG_FB_VIRTUAL is not set
 # CONFIG_BACKLIGHT_LCD_SUPPORT is not set
 
 #
@@ -688,8 +733,22 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_DISPLAY_SUPPORT is not set
 
 #
-# Sound
-#
+# Console display driver support
+#
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_LOGO_SUPERH_MONO=y
+CONFIG_LOGO_SUPERH_VGA16=y
+CONFIG_LOGO_SUPERH_CLUT224=y
 # CONFIG_SOUND is not set
 # CONFIG_HID_SUPPORT is not set
 CONFIG_USB_SUPPORT=y
@@ -788,11 +847,27 @@ CONFIG_USB_MON=y
 # CONFIG_USB_IOWARRIOR is not set
 # CONFIG_USB_ISIGHTFW is not set
 # CONFIG_USB_GADGET is not set
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
 # CONFIG_MEMSTICK is not set
 # CONFIG_NEW_LEDS is not set
 # CONFIG_ACCESSIBILITY is not set
 # CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
 # CONFIG_UIO is not set
 
 #
@@ -865,6 +940,7 @@ CONFIG_TMPFS_POSIX_ACL=y
 # CONFIG_CRAMFS is not set
 # CONFIG_VXFS_FS is not set
 # CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
 # CONFIG_HPFS_FS is not set
 # CONFIG_QNX4FS_FS is not set
 # CONFIG_ROMFS_FS is not set
@@ -874,12 +950,11 @@ CONFIG_NETWORK_FILESYSTEMS=y
 CONFIG_NFS_FS=y
 # CONFIG_NFS_V3 is not set
 # CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
 CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
 CONFIG_LOCKD=y
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
 # CONFIG_RPCSEC_GSS_KRB5 is not set
 # CONFIG_RPCSEC_GSS_SPKM3 is not set
 # CONFIG_SMB_FS is not set
@@ -949,6 +1024,7 @@ CONFIG_FRAME_WARN=1024
 # CONFIG_HEADERS_CHECK is not set
 # CONFIG_DEBUG_KERNEL is not set
 # CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
 # CONFIG_SAMPLES is not set
 # CONFIG_SH_STANDARD_BIOS is not set
 # CONFIG_EARLY_SCIF_CONSOLE is not set
@@ -1003,6 +1079,10 @@ CONFIG_CRYPTO=y
 # CONFIG_CRYPTO_MD4 is not set
 # CONFIG_CRYPTO_MD5 is not set
 # CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
 # CONFIG_CRYPTO_SHA1 is not set
 # CONFIG_CRYPTO_SHA256 is not set
 # CONFIG_CRYPTO_SHA512 is not set
@@ -1042,6 +1122,7 @@ CONFIG_BITREVERSE=y
 # CONFIG_GENERIC_FIND_FIRST_BIT is not set
 # CONFIG_CRC_CCITT is not set
 # CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
 # CONFIG_CRC7 is not set

arch/sh/include/asm/flat.h

@@ -21,4 +21,11 @@
 #define	flat_get_relocate_addr(rel)		(rel)
 #define	flat_set_persistent(relval, p)		({ (void)p; 0; })
 
+#define FLAT_PLAT_INIT(_r) \
+  do { _r->regs[0]=0; _r->regs[1]=0; _r->regs[2]=0; _r->regs[3]=0; \
+       _r->regs[4]=0; _r->regs[5]=0; _r->regs[6]=0; _r->regs[7]=0; \
+       _r->regs[8]=0; _r->regs[9]=0; _r->regs[10]=0; _r->regs[11]=0; \
+       _r->regs[12]=0; _r->regs[13]=0; _r->regs[14]=0; \
+       _r->sr = SR_FD; } while (0)
+
 #endif /* __ASM_SH_FLAT_H */

arch/sh/include/asm/migor.h

@@ -42,9 +42,6 @@
 
 #define PORT_MSELCRB 0xa4050182
 
-#define MSTPCR1 0xa4150034
-#define MSTPCR2 0xa4150038
-
 #define PORT_PSELA 0xa405014e
 #define PORT_PSELB 0xa4050150
 #define PORT_PSELC 0xa4050152

arch/sh/include/asm/sh_mobile_lcdc.h

@@ -47,12 +47,18 @@ struct sh_mobile_lcdc_board_cfg {
 	void (*display_off)(void *board_data);
 };
 
+struct sh_mobile_lcdc_lcd_size_cfg { /* width and height of panel in mm */
+	unsigned long width;
+	unsigned long height;
+};
+
 struct sh_mobile_lcdc_chan_cfg {
 	int chan;
 	int bpp;
 	int interface_type; /* selects RGBn or SYSn I/F, see above */
 	int clock_divider;
 	struct fb_videomode lcd_cfg;
+	struct sh_mobile_lcdc_lcd_size_cfg lcd_size_cfg;
 	struct sh_mobile_lcdc_board_cfg board_cfg;
 	struct sh_mobile_lcdc_sys_bus_cfg sys_bus_cfg; /* only for SYSn I/F */
 };

arch/sh/include/cpu-sh3/cpu/cacheflush.h

@@ -29,6 +29,16 @@ void flush_cache_page(struct vm_area_struct *vma, unsigned long addr, unsigned l
 void flush_dcache_page(struct page *pg);
 void flush_icache_range(unsigned long start, unsigned long end);
 void flush_icache_page(struct vm_area_struct *vma, struct page *page);
+
+#define flush_dcache_mmap_lock(mapping)		do { } while (0)
+#define flush_dcache_mmap_unlock(mapping)	do { } while (0)
+
+/* SH3 has unified cache so no special action needed here */
+#define flush_cache_sigtramp(vaddr)		do { } while (0)
+#define flush_icache_user_range(vma,pg,adr,len)	do { } while (0)
+
+#define p3_cache_init()				do { } while (0)
+
 #else
 #include <cpu-common/cpu/cacheflush.h>
 #endif

arch/sh/kernel/cpu/sh4a/setup-sh7723.c

@@ -45,7 +45,7 @@ static struct platform_device vpu_device = {
 };
 
 static struct uio_info veu0_platform_data = {
-	.name = "VEU",
+	.name = "VEU2H",
 	.version = "0",
 	.irq = 54,
 };
@@ -73,7 +73,7 @@ static struct platform_device veu0_device = {
 };
 
 static struct uio_info veu1_platform_data = {
-	.name = "VEU",
+	.name = "VEU2H",
 	.version = "0",
 	.irq = 27,
 };

arch/sh/kernel/sh_ksyms_32.c

@@ -107,10 +107,12 @@ DECLARE_EXPORT(__movmemSI12_i4);
  * GCC >= 4.2 emits these for division, as do GCC 4.1.x versions of the ST
  * compiler which include backported patches.
  */
-DECLARE_EXPORT(__sdivsi3_i4i);
 DECLARE_EXPORT(__udiv_qrnnd_16);
+#if !defined(CONFIG_CPU_SH2)
+DECLARE_EXPORT(__sdivsi3_i4i);
 DECLARE_EXPORT(__udivsi3_i4i);
 #endif
+#endif
 #else /* GCC 3.x */
 DECLARE_EXPORT(__movstr_i4_even);
 DECLARE_EXPORT(__movstr_i4_odd);

arch/sh/mm/Kconfig

@@ -181,10 +181,12 @@ config ENTRY_OFFSET
 choice
 	prompt "HugeTLB page size"
 	depends on HUGETLB_PAGE && (CPU_SH4 || CPU_SH5) && MMU
+	default HUGETLB_PAGE_SIZE_1MB if PAGE_SIZE_64KB
 	default HUGETLB_PAGE_SIZE_64K
 
 config HUGETLB_PAGE_SIZE_64K
 	bool "64kB"
+	depends on !PAGE_SIZE_64KB
 
 config HUGETLB_PAGE_SIZE_256K
 	bool "256kB"

arch/sh/mm/consistent.c

@@ -95,6 +95,29 @@ void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
 }
 EXPORT_SYMBOL(dma_cache_sync);
 
+static int __init memchunk_setup(char *str)
+{
+	return 1; /* accept anything that begins with "memchunk." */
+}
+__setup("memchunk.", memchunk_setup);
+
+static void memchunk_cmdline_override(char *name, unsigned long *sizep)
+{
+	char *p = boot_command_line;
+	int k = strlen(name);
+
+	while ((p = strstr(p, "memchunk."))) {
+		p += 9; /* strlen("memchunk.") */
+		if (!strncmp(name, p, k) && p[k] == '=') {
+			p += k + 1;
+			*sizep = memparse(p, NULL);
+			pr_info("%s: forcing memory chunk size to 0x%08lx\n",
+				name, *sizep);
+			break;
+		}
+	}
+}
+
 int platform_resource_setup_memory(struct platform_device *pdev,
 				   char *name, unsigned long memsize)
 {
@@ -109,6 +132,10 @@ int platform_resource_setup_memory(struct platform_device *pdev,
 		return -EINVAL;
 	}
 
+	memchunk_cmdline_override(name, &memsize);
+	if (!memsize)
+		return 0;
+
 	buf = dma_alloc_coherent(NULL, memsize, &dma_handle, GFP_KERNEL);
 	if (!buf) {
 		pr_warning("%s: unable to allocate memory\n", name);

drivers/input/touchscreen/migor_ts.c

@@ -173,7 +173,7 @@ static int migor_ts_probe(struct i2c_client *client,
 	input_set_abs_params(input, ABS_X, 95, 955, 0, 0);
 	input_set_abs_params(input, ABS_Y, 85, 935, 0, 0);
 
-	input->name = client->driver_name;
+	input->name = client->name;
 	input->id.bustype = BUS_I2C;
 	input->dev.parent = &client->dev;
 
@@ -192,7 +192,7 @@ static int migor_ts_probe(struct i2c_client *client,
 		goto err1;
 
 	error = request_irq(priv->irq, migor_ts_isr, IRQF_TRIGGER_LOW,
-			    client->driver_name, priv);
+			    client->name, priv);
 	if (error) {
 		dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
 		goto err2;
@@ -224,12 +224,19 @@ static int migor_ts_remove(struct i2c_client *client)
 	return 0;
 }
 
+static const struct i2c_device_id migor_ts_id[] = {
+	{ "migor_ts", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, migor_ts);
+
 static struct i2c_driver migor_ts_driver = {
 	.driver = {
 		.name = "migor_ts",
 	},
 	.probe = migor_ts_probe,
 	.remove = migor_ts_remove,
+	.id_table = migor_ts_id,
 };
 
 static int __init migor_ts_init(void)

drivers/video/sh_mobile_lcdcfb.c

@@ -595,6 +595,8 @@ static int __init sh_mobile_lcdc_probe(struct platform_device *pdev)
 		info->fbops = &sh_mobile_lcdc_ops;
 		info->var.xres = info->var.xres_virtual = cfg->lcd_cfg.xres;
 		info->var.yres = info->var.yres_virtual = cfg->lcd_cfg.yres;
+		info->var.width = cfg->lcd_size_cfg.width;
+		info->var.height = cfg->lcd_size_cfg.height;
 		info->var.activate = FB_ACTIVATE_NOW;
 		error = sh_mobile_lcdc_set_bpp(&info->var, cfg->bpp);
 		if (error)

fs/binfmt_flat.c

@@ -914,7 +914,9 @@ static int load_flat_binary(struct linux_binprm * bprm, struct pt_regs * regs)
 	/* Stash our initial stack pointer into the mm structure */
 	current->mm->start_stack = (unsigned long )sp;
 
-	
+#ifdef FLAT_PLAT_INIT
+	FLAT_PLAT_INIT(regs);
+#endif
 	DBG_FLT("start_thread(regs=0x%x, entry=0x%x, start_stack=0x%x)\n",
 		(int)regs, (int)start_addr, (int)current->mm->start_stack);