Commit 1e393c6e authored by Bob Liu's avatar Bob Liu Committed by Felipe Balbi

USB: musb: blackfin: pm: make it work

Split the USB MMR init steps out into a helper func that both the platform
init and the resume code may call.

Then while suspending, the gpio_vrsel will change from high to low which
will generate a wakeup event and resume the system immediately, so we need
to manually drive it low before we sleep.
Signed-off-by: default avatarBob Liu <lliubbo@gmail.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
parent 32d5dc95
......@@ -323,30 +323,8 @@ int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
return -EIO;
}
int __init musb_platform_init(struct musb *musb, void *board_data)
static void musb_platform_reg_init(struct musb *musb)
{
/*
* Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
* and OTG HOST modes, while rev 1.1 and greater require PE7 to
* be low for DEVICE mode and high for HOST mode. We set it high
* here because we are in host mode
*/
if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
musb->config->gpio_vrsel);
return -ENODEV;
}
gpio_direction_output(musb->config->gpio_vrsel, 0);
usb_nop_xceiv_register();
musb->xceiv = otg_get_transceiver();
if (!musb->xceiv) {
gpio_free(musb->config->gpio_vrsel);
return -ENODEV;
}
if (ANOMALY_05000346) {
bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
SSYNC();
......@@ -380,6 +358,33 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
SSYNC();
}
int __init musb_platform_init(struct musb *musb, void *board_data)
{
/*
* Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
* and OTG HOST modes, while rev 1.1 and greater require PE7 to
* be low for DEVICE mode and high for HOST mode. We set it high
* here because we are in host mode
*/
if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
musb->config->gpio_vrsel);
return -ENODEV;
}
gpio_direction_output(musb->config->gpio_vrsel, 0);
usb_nop_xceiv_register();
musb->xceiv = otg_get_transceiver();
if (!musb->xceiv) {
gpio_free(musb->config->gpio_vrsel);
return -ENODEV;
}
musb_platform_reg_init(musb);
if (is_host_enabled(musb)) {
musb->board_set_vbus = bfin_set_vbus;
......@@ -394,6 +399,27 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
return 0;
}
#ifdef CONFIG_PM
void musb_platform_save_context(struct musb *musb,
struct musb_context_registers *musb_context)
{
if (is_host_active(musb))
/*
* During hibernate gpio_vrsel will change from high to low
* low which will generate wakeup event resume the system
* immediately. Set it to 0 before hibernate to avoid this
* wakeup event.
*/
gpio_set_value(musb->config->gpio_vrsel, 0);
}
void musb_platform_restore_context(struct musb *musb,
struct musb_context_registers *musb_context)
{
musb_platform_reg_init(musb);
}
#endif
int musb_platform_exit(struct musb *musb)
{
gpio_free(musb->config->gpio_vrsel);
......
......@@ -487,7 +487,7 @@ struct musb_context_registers {
};
#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \
defined(CONFIG_ARCH_OMAP4)
defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_BLACKFIN)
extern void musb_platform_save_context(struct musb *musb,
struct musb_context_registers *musb_context);
extern void musb_platform_restore_context(struct musb *musb,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment