Merge tag 'v4.9-rockchip-dts32-1' of...

Merge tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "Rockchip dts32 changes for 4.9" from Heiko Stübner:

32bit Rockchip devicetree changes containing two new rk3288 boards (Fennec
and Firefly-reload), display support for the rk3288-evb, support for the
recently added firmware reboot-flag support and some housekeeping cleanups.

* tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: Add sensor-supplies on PopMetal-RK3288 board
  ARM: dts: rockchip: fix L3G4200D i2c address on PopMetal-RK3288 board
  ARM: dts: rockchip: enable usbotg for Popemtal-rk3288 board
  ARM: dts: rockchip: add missing regulators for firefly reload board
  ARM: dts: rockchip: remove excess sd properties from firefly reload
  ARM: dts: rockchip: add syscon-reboot-mode DT node
  soc: rockchip: add reboot-mode header
  ARM: dts: rockchip: move rk3288 usbphy under the GRF node
  ARM: dts: rockchip: add rk3288-firefly-reload
  ARM: dts: rockchip: add dts for RK3288-Fennec boards
  ARM: dts: rockchip: add the panel power supply for rk3288-evb board with rk808 pmu
  ARM: dts: rockchip: add the panel power supply for rk3288-evb board with act8846 pmu
  ARM: dts: rockchip: add eDP/panel display device nodes for rk3288-evb

Documentation/devicetree/bindings/arm/rockchip.txt

@@ -31,6 +31,10 @@ Rockchip platforms device tree bindings
     or
       - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
 
+- Firefly Firefly-RK3288 Reload board:
+    Required root node properties:
+      - compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
@@ -110,6 +114,10 @@ Rockchip platforms device tree bindings
 - Rockchip RK3229 Evaluation board:
      - compatible = "rockchip,rk3229-evb", "rockchip,rk3229";
 
+- Rockchip RK3288 Fennec board:
+    Required root node properties:
+     - compatible = "rockchip,rk3288-fennec", "rockchip,rk3288";
+
 - Rockchip RK3399 evb:
     Required root node properties:
       - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";

arch/arm/boot/dts/Makefile

@@ -625,8 +625,10 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3229-evb.dtb \
 	rk3288-evb-act8846.dtb \
 	rk3288-evb-rk808.dtb \
+	rk3288-fennec.dtb \
 	rk3288-firefly-beta.dtb \
 	rk3288-firefly.dtb \
+	rk3288-firefly-reload.dtb \
 	rk3288-miqi.dtb \
 	rk3288-popmetal.dtb \
 	rk3288-r89.dtb \

arch/arm/boot/dts/rk3036.dtsi

@@ -43,6 +43,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/pinctrl/rockchip.h>
 #include <dt-bindings/clock/rk3036-cru.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
 #include "skeleton.dtsi"
 
 / {
@@ -313,8 +314,17 @@ cru: clock-controller@20000000 {
 	};
 
 	grf: syscon@20008000 {
-		compatible = "rockchip,rk3036-grf", "syscon";
+		compatible = "rockchip,rk3036-grf", "syscon", "simple-mfd";
 		reg = <0x20008000 0x1000>;
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x1d8>;
+			mode-normal = <BOOT_NORMAL>;
+			mode-recovery = <BOOT_RECOVERY>;
+			mode-bootloader = <BOOT_FASTBOOT>;
+			mode-loader = <BOOT_BL_DOWNLOAD>;
+		};
 	};
 
 	acodec: acodec-ana@20030000 {

arch/arm/boot/dts/rk3288-evb-act8846.dts

@@ -206,6 +206,10 @@ vcc18_lcd: REG12 {
 	};
 };
 
+&panel {
+	power-supply = <&vcc_lcd>;
+};
+
 &pinctrl {
 	lcd {
 		lcd_en: lcd-en  {

arch/arm/boot/dts/rk3288-evb-rk808.dts

@@ -233,3 +233,7 @@ regulator-state-mem {
 		};
 	};
 };
+
+&panel {
+	power-supply = <&vcc_lcd>;
+};

arch/arm/boot/dts/rk3288-evb.dtsi

@@ -48,7 +48,7 @@ memory {
 		reg = <0x0 0x80000000>;
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		brightness-levels = <
 			  0   1   2   3   4   5   6   7
@@ -97,6 +97,21 @@ ext_gmac: external-gmac-clock {
 		#clock-cells = <0>;
 	};
 
+	panel: panel {
+		compatible ="lg,lp079qx1-sp0v", "simple-panel";
+		backlight = <&backlight>;
+		enable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&lcd_cs>;
+
+		ports {
+			panel_in: port {
+				panel_in_edp: endpoint {
+					remote-endpoint = <&edp_out_panel>;
+				};
+			};
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -170,6 +185,28 @@ &cpu0 {
 	cpu0-supply = <&vdd_cpu>;
 };
 
+&edp {
+	force-hpd;
+	status = "okay";
+
+	ports {
+		edp_out: port@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			edp_out_panel: endpoint {
+				reg = <0>;
+				remote-endpoint = <&panel_in_edp>;
+			};
+		};
+	};
+};
+
+&edp_phy {
+	status = "okay";
+};
+
 &emmc {
 	bus-width = <8>;
 	cap-mmc-highspeed;
@@ -280,6 +317,12 @@ pwrbtn: pwrbtn {
 		};
 	};
 
+	lcd {
+		lcd_cs: lcd-cs {
+			rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		pmic_int: pmic-int {
 			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;

arch/arm/boot/dts/rk3288-fennec.dts

+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+	model = "Rockchip RK3288 Fennec Board";
+	compatible = "rockchip,rk3288-fennec", "rockchip,rk3288";
+
+	memory {
+		reg = <0x0 0x80000000>;
+		device_type = "memory";
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_io>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_io>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_33: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_33";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_wl: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_sd: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lan: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	gmac {
+		phy_int: phy-int {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_pmeb: phy-pmeb {
+			rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_rst: phy-rst {
+			rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usbphy {
+		host_drv: host-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&host_drv>;
+	vbus_drv-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&usb_hsic {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};

arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi

+/*
+ * Device tree file for Firefly Rockchip RK3288 Core board
+ * Copyright (c) 2016 Randy Li <ayaka@soulik.info>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+
+	vcc_flash: flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_flash>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	vdd_cpu: syr827@40 {
+		compatible = "silergy,syr827";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x40>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-enable-ramp-delay = <300>;
+		regulator-ramp-delay = <8000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: syr828@41 {
+		compatible = "silergy,syr828";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x41>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	act8846: act8846@5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_vsel>, <&pwr_hold>;
+		system-power-controller;
+
+		vp1-supply = <&vcc_sys>;
+		vp2-supply = <&vcc_sys>;
+		vp3-supply = <&vcc_sys>;
+		vp4-supply = <&vcc_sys>;
+		inl1-supply = <&vcc_sys>;
+		inl2-supply = <&vcc_sys>;
+		inl3-supply = <&vcc_20>;
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "vcc_ddr";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "vdd_log";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "vcc_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			vcca_18: REG7  {
+				regulator-name = "vcca_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcca_33: REG8 {
+				regulator-name = "vcca_33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vcc_lan: REG9 {
+				regulator-name = "vcca_lan";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vccio_wl: vcc_18: REG11 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "vcc18_lcd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+&io_domains {
+	status = "okay";
+
+	audio-supply = <&vccio_wl>;
+	bb-supply = <&vcc_io>;
+	dvp-supply = <&dovdd_1v8>;
+	flash0-supply = <&vcc_flash>;
+	flash1-supply = <&vcc_lan>;
+	gpio30-supply = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
+	lcdc-supply = <&vcc_io>;
+	sdcard-supply = <&vccio_sd>;
+	wifi-supply = <&vccio_wl>;
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+		bias-pull-up;
+		drive-strength = <12>;
+	};
+
+	act8846 {
+		pwr_hold: pwr-hold {
+			rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+
+		pmic_vsel: pmic-vsel {
+			rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+	};
+
+	gmac {
+		phy_int: phy-int {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_pmeb: phy-pmeb {
+			rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_rst: phy-rst {
+			rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

arch/arm/boot/dts/rk3288-firefly-reload.dts

+/*
+ * Device tree file for Firefly Rockchip RK3288 Core board
+ * Copyright (c) 2016 Randy Li <ayaka@soulik.info>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3288-firefly-reload-core.dtsi"
+
+/ {
+	model = "Firefly-RK3288-reload";
+	compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			wakeup-source;
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Power";
+			linux,code = <KEY_POWER>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwr_key>;
+		};
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			gpios = <&gpio8 2 GPIO_ACTIVE_LOW>;
+			label = "firefly:blue:power";
+			pinctrl-names = "default";
+			pinctrl-0 = <&power_led>;
+			panic-indicator;
+		};
+
+		work {
+			gpios = <&gpio8 1 GPIO_ACTIVE_LOW>;
+			label = "firefly:blue:user";
+			linux,default-trigger = "rc-feedback";
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&hym8563>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable>;
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+		simple-audio-card,dai-link@1 {  /* S/PDIF - S/PDIF */
+			cpu { sound-dai = <&spdif>; };
+			codec { sound-dai = <&spdif_out>; };
+		};
+	};
+
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	vcc_host_5v: usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	vcc_5v: vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_otg_5v: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	dovdd_1v8: dovdd-1v8-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dvp_pwr>;
+		regulator-name = "dovdd_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc28_dvp: vcc28-dvp-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dvp_pwr>;
+		regulator-name = "vcc28_dvp";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	af_28: af_28-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dvp_pwr>;
+		regulator-name = "af_28";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	dvdd_1v2: af_28-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cif_pwr>;
+		regulator-name = "dvdd_1v2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vbat_wl: wifi-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat_wl";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&i2c0 {
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio7>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	codec: es8328@10 {
+		compatible = "everest,es8328";
+		DVDD-supply = <&vcca_33>;
+		AVDD-supply = <&vcca_33>;
+		PVDD-supply = <&vcca_33>;
+		HPVDD-supply = <&vcca_33>;
+		clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
+		clock-names = "i2s_hclk", "i2s_clk";
+		reg = <0x10>;
+	};
+};
+
+&i2s {
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdio0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	disable-wp;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>, <&sdio0_int>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	vmmc-supply = <&vbat_wl>;
+	vqmmc-supply = <&vccio_wl>;
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbhub_rst>;
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&pinctrl {
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	dvp {
+		dvp_pwr: dvp-pwr {
+			rockchip,pins = <0 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		cif_pwr: cif-pwr {
+			rockchip,pins = <7 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		rtc_int: rtc-int {
+			rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	keys {
+		pwr_key: pwr-key {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		power_led: power-led {
+			rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		work_led: work-led {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		/*
+		 * Default drive strength isn't enough to achieve even
+		 * high-speed mode on firefly board so bump up to 12ma.
+		 */
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio {
+		wifi_enable: wifi-enable {
+			rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_host {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usbhub_rst: usbhub-rst {
+			rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};

arch/arm/boot/dts/rk3288-popmetal.dts

@@ -387,12 +387,16 @@ ak8963: ak8963@0d {
 		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&comp_int>;
+		vdd-supply = <&vcc_io>;
+		vid-supply = <&vcc_io>;
 	};
 
-	l3g4200d: l3g4200d@68 {
+	l3g4200d: l3g4200d@69 {
 		compatible = "st,l3g4200d-gyro";
 		st,drdy-int-pin = <2>;
-		reg = <0x6b>;
+		reg = <0x69>;
+		vdd-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
 	};
 
 	mma8452: mma8452@1d {
@@ -525,3 +529,7 @@ &uart4 {
 &usbphy {
 	status = "okay";
 };
+
+&usb_otg {
+	status = "okay";
+};

arch/arm/boot/dts/rk3288.dtsi

@@ -45,6 +45,7 @@
 #include <dt-bindings/clock/rk3288-cru.h>
 #include <dt-bindings/thermal/thermal.h>
 #include <dt-bindings/power/rk3288-power.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
 #include "skeleton.dtsi"
 
 / {
@@ -791,6 +792,15 @@ pd_gpu@RK3288_PD_GPU {
 				clocks = <&cru ACLK_GPU>;
 			};
 		};
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x94>;
+			mode-normal = <BOOT_NORMAL>;
+			mode-recovery = <BOOT_RECOVERY>;
+			mode-bootloader = <BOOT_FASTBOOT>;
+			mode-loader = <BOOT_BL_DOWNLOAD>;
+		};
 	};
 
 	sgrf: syscon@ff740000 {
@@ -832,6 +842,37 @@ io_domains: io-domains {
 			compatible = "rockchip,rk3288-io-voltage-domain";
 			status = "disabled";
 		};
+
+		usbphy: usbphy {
+			compatible = "rockchip,rk3288-usb-phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			usbphy0: usb-phy@320 {
+				#phy-cells = <0>;
+				reg = <0x320>;
+				clocks = <&cru SCLK_OTGPHY0>;
+				clock-names = "phyclk";
+				#clock-cells = <0>;
+			};
+
+			usbphy1: usb-phy@334 {
+				#phy-cells = <0>;
+				reg = <0x334>;
+				clocks = <&cru SCLK_OTGPHY1>;
+				clock-names = "phyclk";
+				#clock-cells = <0>;
+			};
+
+			usbphy2: usb-phy@348 {
+				#phy-cells = <0>;
+				reg = <0x348>;
+				clocks = <&cru SCLK_OTGPHY2>;
+				clock-names = "phyclk";
+				#clock-cells = <0>;
+			};
+		};
 	};
 
 	wdt: watchdog@ff800000 {
@@ -1085,38 +1126,6 @@ cpu_leakage: cpu_leakage@17 {
 		};
 	};
 
-	usbphy: phy {
-		compatible = "rockchip,rk3288-usb-phy";
-		rockchip,grf = <&grf>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-
-		usbphy0: usb-phy@320 {
-			#phy-cells = <0>;
-			reg = <0x320>;
-			clocks = <&cru SCLK_OTGPHY0>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-
-		usbphy1: usb-phy@334 {
-			#phy-cells = <0>;
-			reg = <0x334>;
-			clocks = <&cru SCLK_OTGPHY1>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-
-		usbphy2: usb-phy@348 {
-			#phy-cells = <0>;
-			reg = <0x348>;
-			clocks = <&cru SCLK_OTGPHY2>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-	};
-
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3288-pinctrl";
 		rockchip,grf = <&grf>;

arch/arm/boot/dts/rk3xxx.dtsi

@@ -43,6 +43,7 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
 #include "skeleton.dtsi"
 
 / {
@@ -246,8 +247,17 @@ emmc: dwmmc@1021c000 {
 	};
 
 	pmu: pmu@20004000 {
-		compatible = "rockchip,rk3066-pmu", "syscon";
+		compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd";
 		reg = <0x20004000 0x100>;
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x40>;
+			mode-normal = <BOOT_NORMAL>;
+			mode-recovery = <BOOT_RECOVERY>;
+			mode-bootloader = <BOOT_FASTBOOT>;
+			mode-loader = <BOOT_BL_DOWNLOAD>;
+		};
 	};
 
 	grf: grf@20008000 {

include/dt-bindings/soc/rockchip,boot-mode.h

+#ifndef __ROCKCHIP_BOOT_MODE_H
+#define __ROCKCHIP_BOOT_MODE_H
+
+/*high 24 bits is tag, low 8 bits is type*/
+#define REBOOT_FLAG		0x5242C300
+/* normal boot */
+#define BOOT_NORMAL		(REBOOT_FLAG + 0)
+/* enter bootloader rockusb mode */
+#define BOOT_BL_DOWNLOAD	(REBOOT_FLAG + 1)
+/* enter recovery */
+#define BOOT_RECOVERY		(REBOOT_FLAG + 3)
+ /* enter fastboot mode */
+#define BOOT_FASTBOOT		(REBOOT_FLAG + 9)
+
+#endif