mips: ralink: remove reset related code

A proper clock driver for ralink SoCs has been added. This driver is also
a reset provider for the SoC. Hence there is no need to have reset related
code in 'arch/mips/ralink' folder anymore. The only code that remains is
the one related with mips_reboot_setup where a PCI reset is performed.
We maintain this because I cannot test old ralink board with PCI to be
sure all works if we remove also this code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

arch/mips/ralink/common.h

@@ -23,8 +23,6 @@ extern struct ralink_soc_info soc_info;
 
 extern void ralink_of_remap(void);
 
-extern void ralink_rst_init(void);
-
 extern void __init prom_soc_init(struct ralink_soc_info *soc_info);
 
 __iomem void *plat_of_remap_node(const char *node);

arch/mips/ralink/of.c

@@ -81,10 +81,6 @@ static int __init plat_of_setup(void)
 {
 	__dt_register_buses(soc_info.compatible, "palmbus");
 
-	/* make sure that the reset controller is setup early */
-	if (ralink_soc != MT762X_SOC_MT7621AT)
-		ralink_rst_init();
-
 	return 0;
 }
 

arch/mips/ralink/reset.c

@@ -10,7 +10,6 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/delay.h>
-#include <linux/reset-controller.h>
 
 #include <asm/reboot.h>
 
@@ -22,66 +21,6 @@
 #define RSTCTL_RESET_PCI	BIT(26)
 #define RSTCTL_RESET_SYSTEM	BIT(0)
 
-static int ralink_assert_device(struct reset_controller_dev *rcdev,
-				unsigned long id)
-{
-	u32 val;
-
-	if (id == 0)
-		return -1;
-
-	val = rt_sysc_r32(SYSC_REG_RESET_CTRL);
-	val |= BIT(id);
-	rt_sysc_w32(val, SYSC_REG_RESET_CTRL);
-
-	return 0;
-}
-
-static int ralink_deassert_device(struct reset_controller_dev *rcdev,
-				  unsigned long id)
-{
-	u32 val;
-
-	if (id == 0)
-		return -1;
-
-	val = rt_sysc_r32(SYSC_REG_RESET_CTRL);
-	val &= ~BIT(id);
-	rt_sysc_w32(val, SYSC_REG_RESET_CTRL);
-
-	return 0;
-}
-
-static int ralink_reset_device(struct reset_controller_dev *rcdev,
-			       unsigned long id)
-{
-	ralink_assert_device(rcdev, id);
-	return ralink_deassert_device(rcdev, id);
-}
-
-static const struct reset_control_ops reset_ops = {
-	.reset = ralink_reset_device,
-	.assert = ralink_assert_device,
-	.deassert = ralink_deassert_device,
-};
-
-static struct reset_controller_dev reset_dev = {
-	.ops			= &reset_ops,
-	.owner			= THIS_MODULE,
-	.nr_resets		= 32,
-	.of_reset_n_cells	= 1,
-};
-
-void ralink_rst_init(void)
-{
-	reset_dev.of_node = of_find_compatible_node(NULL, NULL,
-						"ralink,rt2880-reset");
-	if (!reset_dev.of_node)
-		pr_err("Failed to find reset controller node");
-	else
-		reset_controller_register(&reset_dev);
-}
-
 static void ralink_restart(char *command)
 {
 	if (IS_ENABLED(CONFIG_PCI)) {