ARM: dts: qcom: apq8064: split PMICs to separate dtsi files

The PMICs are not a part of the SoC, so move PMICs to separate files and
include them from the board files.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-18-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm/boot/dts/qcom/pm8821.dtsi

+// SPDX-License-Identifier: GPL-2.0
+
+/* This PMIC is used on a secondary SSBI bus */
+&ssbi2 {
+	pm8821: pmic {
+		compatible = "qcom,pm8821";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8821_mpps: mpps@50 {
+			compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8821_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};

arch/arm/boot/dts/qcom/pm8921.dtsi

@@ -8,6 +8,30 @@ pm8921: pmic {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8921_gpio: gpio@150 {
+
+			compatible = "qcom,pm8921-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8921_gpio 0 0 44>;
+			#gpio-cells = <2>;
+
+		};
+
+		pm8921_mpps: mpps@50 {
+			compatible = "qcom,pm8921-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8921_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
 		pwrkey@1c {
 			compatible = "qcom,pm8921-pwrkey";
 			reg = <0x1c>;
@@ -36,5 +60,80 @@ rtc@11d {
 			reg = <0x11d>;
 			allow-set-time;
 		};
+
+		pm8921_xoadc: xoadc@197 {
+			compatible = "qcom,pm8921-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			batt_therm: adc-channel@8 {
+				reg = <0x00 0x08>;
+			};
+
+			batt_id: adc-channel@9 {
+				reg = <0x00 0x09>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			chg_temp: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
 	};
 };

arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts

 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "Asus Nexus7(flo)";
 	compatible = "asus,nexus7-flo", "qcom,apq8064";

arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts

 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "CompuLab CM-QS600";
 	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";

arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts

 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "Qualcomm APQ8064/IFC6410";
 	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";

arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts

 // SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/mfd/qcom-rpm.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
 / {
 	model = "Sony Xperia Z";
 	compatible = "sony,xperia-yuga", "qcom,apq8064";

arch/arm/boot/dts/qcom/qcom-apq8064.dtsi

@@ -284,23 +284,6 @@ scm {
 		};
 	};
 
-
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
-			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
-			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
-			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
-			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -655,129 +638,16 @@ rng@1a500000 {
 			clock-names = "core";
 		};
 
-		ssbi@c00000 {
+		ssbi2: ssbi@c00000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00c00000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8821: pmic {
-				compatible = "qcom,pm8821";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8821_mpps: mpps@50 {
-					compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
-					reg = <0x50>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8821_mpps 0 0 4>;
-				};
-			};
 		};
 
-		ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8921: pmic {
-				compatible = "qcom,pm8921";
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8921_gpio: gpio@150 {
-
-					compatible = "qcom,pm8921-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8921_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8921_mpps: mpps@50 {
-					compatible = "qcom,pm8921-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8921_mpps 0 0 12>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pm8921>;
-					interrupts = <39 1>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8921>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pm8921_xoadc: xoadc@197 {
-					compatible = "qcom,pm8921-adc";
-					reg = <0x197>;
-					interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@0 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@1 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@2 {
-						reg = <0x00 0x02>;
-					};
-					vph_pwr: adc-channel@4 {
-						reg = <0x00 0x04>;
-					};
-					batt_therm: adc-channel@8 {
-						reg = <0x00 0x08>;
-					};
-					batt_id: adc-channel@9 {
-						reg = <0x00 0x09>;
-					};
-					usb_vbus: adc-channel@a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@d {
-						reg = <0x00 0x0d>;
-					};
-					chg_temp: adc-channel@e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@f {
-						reg = <0x00 0x0f>;
-					};
-				};
-			};
 		};
 
 		qfprom: qfprom@700000 {