Commit 23a7a51c authored by Luciano Coelho's avatar Luciano Coelho Committed by John W. Linville

wl1271: fix a bunch of sparse warnings

A couple of sparse warnings in some rate settings (missing cpu_to_le32) were
fixed.  Changed the conf_sg_settings struct from le to native endianess.  The
values are converted to le when copying them to the acx command instead.
Reported-by: default avatarJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: default avatarLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: default avatarJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent 82429d32
......@@ -589,7 +589,7 @@ int wl1271_acx_sg_cfg(struct wl1271 *wl)
/* BT-WLAN coext parameters */
for (i = 0; i < CONF_SG_PARAMS_MAX; i++)
param->params[i] = c->params[i];
param->params[i] = cpu_to_le32(c->params[i]);
param->param_idx = CONF_SG_PARAMS_ALL;
ret = wl1271_cmd_configure(wl, ACX_SG_CFG, param, sizeof(*param));
......
......@@ -350,7 +350,7 @@ static int wl1271_boot_soft_reset(struct wl1271 *wl)
static int wl1271_boot_run_firmware(struct wl1271 *wl)
{
int loop, ret;
u32 chip_id, interrupt;
u32 chip_id, intr;
wl1271_boot_set_ecpu_ctrl(wl, ECPU_CONTROL_HALT);
......@@ -367,15 +367,15 @@ static int wl1271_boot_run_firmware(struct wl1271 *wl)
loop = 0;
while (loop++ < INIT_LOOP) {
udelay(INIT_LOOP_DELAY);
interrupt = wl1271_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR);
intr = wl1271_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR);
if (interrupt == 0xffffffff) {
if (intr == 0xffffffff) {
wl1271_error("error reading hardware complete "
"init indication");
return -EIO;
}
/* check that ACX_INTR_INIT_COMPLETE is enabled */
else if (interrupt & WL1271_ACX_INTR_INIT_COMPLETE) {
else if (intr & WL1271_ACX_INTR_INIT_COMPLETE) {
wl1271_write32(wl, ACX_REG_INTERRUPT_ACK,
WL1271_ACX_INTR_INIT_COMPLETE);
break;
......
......@@ -317,7 +317,7 @@ int wl1271_cmd_join(struct wl1271 *wl, u8 bss_type)
join->rx_config_options = cpu_to_le32(wl->rx_config);
join->rx_filter_options = cpu_to_le32(wl->rx_filter);
join->bss_type = bss_type;
join->basic_rate_set = wl->basic_rate_set;
join->basic_rate_set = cpu_to_le32(wl->basic_rate_set);
if (wl->band == IEEE80211_BAND_5GHZ)
join->bss_type |= WL1271_JOIN_CMD_BSS_TYPE_5GHZ;
......@@ -614,7 +614,7 @@ int wl1271_cmd_scan(struct wl1271 *wl, const u8 *ssid, size_t ssid_len,
params->params.scan_options = cpu_to_le16(scan_options);
params->params.num_probe_requests = probe_requests;
params->params.tx_rate = rate;
params->params.tx_rate = cpu_to_le32(rate);
params->params.tid_trigger = 0;
params->params.scan_tag = WL1271_SCAN_DEFAULT_TAG;
......
......@@ -401,7 +401,7 @@ enum {
};
struct conf_sg_settings {
__le32 params[CONF_SG_PARAMS_MAX];
u32 params[CONF_SG_PARAMS_MAX];
u8 state;
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment