[media] Documentation/media: Remove docs for obsoleted and removed v4l1 drivers

When the v4l1 drivers were removed, there docs were forgotten.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Documentation/video4linux/m5602.txt

-This document describes the ALi m5602 bridge connected
-to the following supported sensors:
-OmniVision OV9650,
-Samsung s5k83a,
-Samsung s5k4aa,
-Micron mt9m111,
-Pixel plus PO1030
-
-This driver mimics the windows drivers, which have a braindead implementation sending bayer-encoded frames at VGA resolution.
-In a perfect world we should be able to reprogram the m5602 and the connected sensor in hardware instead, supporting a range of resolutions and pixelformats
-
-Anyway, have fun and please report any bugs to m560x-driver-devel@lists.sourceforge.net

Documentation/video4linux/se401.txt

-Linux driver for SE401 based USB cameras
-
-Copyright, 2001, Jeroen Vreeken
-
-
-INTRODUCTION:
-
-The SE401 chip is the used in low-cost usb webcams.
-It is produced by Endpoints Inc. (www.endpoints.com).
-It interfaces directly to a cmos image sensor and USB. The only other major
-part in a se401 based camera is a dram chip.
-
-The following cameras are known to work with this driver:
-
-Aox se401 (non-branded) cameras
-Philips PVCV665 USB VGA webcam 'Vesta Fun'
-Kensington VideoCAM PC Camera Model 67014
-Kensington VideoCAM PC Camera Model 67015
-Kensington VideoCAM PC Camera Model 67016
-Kensington VideoCAM PC Camera Model 67017
-
-
-WHAT YOU NEED:
-
--	USB support
--	VIDEO4LINUX support
-
-More information about USB support for linux can be found at:
-http://www.linux-usb.org
-
-
-MODULE OPTIONS:
-
-When the driver is compiled as a module you can also use the 'flickerless'
-option. With it exposure is limited to values that do not interfere with the
-net frequency. Valid options for this option are 0, 50 and 60. (0=disable,
-50=50hz, 60=60hz)
-
-
-KNOWN PROBLEMS:
-
-The driver works fine with the usb-ohci and uhci host controller drivers,
-the default settings also work with usb-uhci. But sending more than one bulk
-transfer at a time with usb-uhci doesn't work yet.
-Users of usb-ohci and uhci can safely enlarge SE401_NUMSBUF in se401.h in
-order to increase the throughput (and thus framerate).
-
-
-HELP:
-
-The latest info on this driver can be found at:
-http://members.chello.nl/~j.vreeken/se401/
-And questions to me can be send to:
-pe1rxq@amsat.org

Documentation/video4linux/stv680.txt

-Linux driver for STV0680 based USB cameras
-
-Copyright, 2001, Kevin Sisson
-
-
-INTRODUCTION:
-
-STMicroelectronics produces the STV0680B chip, which comes in two
-types, -001 and -003. The -003 version allows the recording and downloading
-of sound clips from the camera, and allows a flash attachment. Otherwise,
-it uses the same commands as the -001 version. Both versions support a
-variety of SDRAM sizes and sensors, allowing for a maximum of 26 VGA or 20
-CIF pictures. The STV0680 supports either a serial or a usb interface, and
-video is possible through the usb interface.
-
-The following cameras are known to work with this driver, although any
-camera with Vendor/Product codes of 0553/0202 should work:
-
-Aiptek Pencam (various models)
-Nisis QuickPix 2
-Radio Shack 'Kid's digital camera' (#60-1207)
-At least one Trust Spycam model
-Several other European brand models
-
-WHAT YOU NEED:
-
--	USB support
--	VIDEO4LINUX support
-
-More information about USB support for linux can be found at:
-http://www.linux-usb.org
-
-
-MODULE OPTIONS:
-
-When the driver is compiled as a module, you can set a "swapRGB=1"
-option, if necessary, for those applications that require it
-(such as xawtv). However, the driver should detect and set this
-automatically, so this option should not normally be used.
-
-
-KNOWN PROBLEMS:
-
-The driver seems to work better with the usb-ohci than the usb-uhci host
-controller driver.
-
-HELP:
-
-The latest info on this driver can be found at:
-http://personal.clt.bellsouth.net/~kjsisson or at
-http://stv0680-usb.sourceforge.net
-
-Any questions to me can be send to:  kjsisson@bellsouth.net

Documentation/video4linux/zc0301.txt

-
-	      ZC0301 and ZC0301P Image Processor and Control Chip
-				Driver for Linux
-	      ===================================================
-
-			       - Documentation -
-
-
-Index
-=====
-1.  Copyright
-2.  Disclaimer
-3.  License
-4.  Overview and features
-5.  Module dependencies
-6.  Module loading
-7.  Module parameters
-8.  Supported devices
-9.  Notes for V4L2 application developers
-10. Contact information
-11. Credits
-
-
-1. Copyright
-============
-Copyright (C) 2006-2007 by Luca Risolia <luca.risolia@studio.unibo.it>
-
-
-2. Disclaimer
-=============
-This software is not developed or sponsored by Z-Star Microelectronics Corp.
-Trademarks are property of their respective owner.
-
-
-3. License
-==========
-This program is free software; you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation; either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program; if not, write to the Free Software
-Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-
-
-4. Overview and features
-========================
-This driver supports the video interface of the devices mounting the ZC0301 or
-ZC0301P Image Processors and Control Chips.
-
-The driver relies on the Video4Linux2 and USB core modules. It has been
-designed to run properly on SMP systems as well.
-
-The latest version of the ZC0301[P] driver can be found at the following URL:
-http://www.linux-projects.org/
-
-Some of the features of the driver are:
-
-- full compliance with the Video4Linux2 API (see also "Notes for V4L2
-  application developers" paragraph);
-- available mmap or read/poll methods for video streaming through isochronous
-  data transfers;
-- automatic detection of image sensor;
-- video format is standard JPEG;
-- dynamic driver control thanks to various module parameters (see "Module
-  parameters" paragraph);
-- up to 64 cameras can be handled at the same time; they can be connected and
-  disconnected from the host many times without turning off the computer, if
-  the system supports hotplugging;
-
-
-5. Module dependencies
-======================
-For it to work properly, the driver needs kernel support for Video4Linux and
-USB.
-
-The following options of the kernel configuration file must be enabled and
-corresponding modules must be compiled:
-
-	# Multimedia devices
-	#
-	CONFIG_VIDEO_DEV=m
-
-	# USB support
-	#
-	CONFIG_USB=m
-
-In addition, depending on the hardware being used, the modules below are
-necessary:
-
-	# USB Host Controller Drivers
-	#
-	CONFIG_USB_EHCI_HCD=m
-	CONFIG_USB_UHCI_HCD=m
-	CONFIG_USB_OHCI_HCD=m
-
-The ZC0301 controller also provides a built-in microphone interface. It is
-supported by the USB Audio driver thanks to the ALSA API:
-
-	# Sound
-	#
-	CONFIG_SOUND=y
-
-	# Advanced Linux Sound Architecture
-	#
-	CONFIG_SND=m
-
-	# USB devices
-	#
-	CONFIG_SND_USB_AUDIO=m
-
-And finally:
-
-	# V4L USB devices
-	#
-	CONFIG_USB_ZC0301=m
-
-
-6. Module loading
-=================
-To use the driver, it is necessary to load the "zc0301" module into memory
-after every other module required: "videodev", "v4l2_common", "compat_ioctl32",
-"usbcore" and, depending on the USB host controller you have, "ehci-hcd",
-"uhci-hcd" or "ohci-hcd".
-
-Loading can be done as shown below:
-
-	[root@localhost home]# modprobe zc0301
-
-At this point the devices should be recognized. You can invoke "dmesg" to
-analyze kernel messages and verify that the loading process has gone well:
-
-	[user@localhost home]$ dmesg
-
-
-7. Module parameters
-====================
-Module parameters are listed below:
--------------------------------------------------------------------------------
-Name:           video_nr
-Type:           short array (min = 0, max = 64)
-Syntax:         <-1|n[,...]>
-Description:    Specify V4L2 minor mode number:
-		-1 = use next available
-		 n = use minor number n
-		You can specify up to 64 cameras this way.
-		For example:
-		video_nr=-1,2,-1 would assign minor number 2 to the second
-		registered camera and use auto for the first one and for every
-		other camera.
-Default:        -1
--------------------------------------------------------------------------------
-Name:           force_munmap
-Type:           bool array (min = 0, max = 64)
-Syntax:         <0|1[,...]>
-Description:    Force the application to unmap previously mapped buffer memory
-		before calling any VIDIOC_S_CROP or VIDIOC_S_FMT ioctl's. Not
-		all the applications support this feature. This parameter is
-		specific for each detected camera.
-		0 = do not force memory unmapping
-		1 = force memory unmapping (save memory)
-Default:        0
--------------------------------------------------------------------------------
-Name:           frame_timeout
-Type:           uint array (min = 0, max = 64)
-Syntax:         <n[,...]>
-Description:    Timeout for a video frame in seconds. This parameter is
-		specific for each detected camera. This parameter can be
-		changed at runtime thanks to the /sys filesystem interface.
-Default:        2
--------------------------------------------------------------------------------
-Name:           debug
-Type:           ushort
-Syntax:         <n>
-Description:    Debugging information level, from 0 to 3:
-		0 = none (use carefully)
-		1 = critical errors
-		2 = significant information
-		3 = more verbose messages
-		Level 3 is useful for testing only, when only one device
-		is used at the same time. It also shows some information
-		about the hardware being detected. This module parameter can be
-		changed at runtime thanks to the /sys filesystem interface.
-Default:        2
--------------------------------------------------------------------------------
-
-
-8. Supported devices
-====================
-None of the names of the companies as well as their products will be mentioned
-here. They have never collaborated with the author, so no advertising.
-
-From the point of view of a driver, what unambiguously identify a device are
-its vendor and product USB identifiers. Below is a list of known identifiers of
-devices mounting the ZC0301 Image Processor and Control Chips:
-
-Vendor ID  Product ID
----------  ----------
-0x041e     0x4017
-0x041e     0x401c
-0x041e     0x401e
-0x041e     0x401f
-0x041e     0x4022
-0x041e     0x4034
-0x041e     0x4035
-0x041e     0x4036
-0x041e     0x403a
-0x0458     0x7007
-0x0458     0x700c
-0x0458     0x700f
-0x046d     0x08ae
-0x055f     0xd003
-0x055f     0xd004
-0x0ac8     0x0301
-0x0ac8     0x301b
-0x0ac8     0x303b
-0x10fd     0x0128
-0x10fd     0x8050
-0x10fd     0x804e
-
-The list above does not imply that all those devices work with this driver: up
-until now only the ones that mount the following image sensors are supported;
-kernel messages will always tell you whether this is the case:
-
-Model       Manufacturer
------       ------------
-PAS202BCB   PixArt Imaging, Inc.
-PB-0330     Photobit Corporation
-
-
-9. Notes for V4L2 application developers
-========================================
-This driver follows the V4L2 API specifications. In particular, it enforces two
-rules:
-
-- exactly one I/O method, either "mmap" or "read", is associated with each
-file descriptor. Once it is selected, the application must close and reopen the
-device to switch to the other I/O method;
-
-- although it is not mandatory, previously mapped buffer memory should always
-be unmapped before calling any "VIDIOC_S_CROP" or "VIDIOC_S_FMT" ioctl's.
-The same number of buffers as before will be allocated again to match the size
-of the new video frames, so you have to map the buffers again before any I/O
-attempts on them.
-
-
-10. Contact information
-=======================
-The author may be contacted by e-mail at <luca.risolia@studio.unibo.it>.
-
-GPG/PGP encrypted e-mail's are accepted. The GPG key ID of the author is
-'FCE635A4'; the public 1024-bit key should be available at any keyserver;
-the fingerprint is: '88E8 F32F 7244 68BA 3958  5D40 99DA 5D2A FCE6 35A4'.
-
-
-11. Credits
-===========
-- Information about the chip internals needed to enable the I2C protocol have
-  been taken from the documentation of the ZC030x Video4Linux1 driver written
-  by Andrew Birkett <andy@nobugs.org>;
-- The initialization values of the ZC0301 controller connected to the PAS202BCB
-  and PB-0330 image sensors have been taken from the SPCA5XX driver maintained
-  by Michel Xhaard <mxhaard@magic.fr>;
-- Stanislav Lechev donated one camera.