Merge branch 'for_2_6_33' of git://git.pwsan.com/linux-2.6 into omap-for-linus

arch/arm/mach-omap1/Makefile

@@ -3,7 +3,8 @@
 #
 
 # Common support
-obj-y := io.o id.o sram.o clock.o irq.o mux.o serial.o devices.o
+obj-y := io.o id.o sram.o irq.o mux.o serial.o devices.o
+obj-y += clock.o clock_data.o opp_data.o
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 

arch/arm/mach-omap1/io.c

@@ -18,7 +18,8 @@
 #include <plat/mux.h>
 #include <plat/tc.h>
 
-extern int omap1_clk_init(void);
+#include "clock.h"
+
 extern void omap_check_revision(void);
 extern void omap_sram_init(void);
 extern void omapfb_reserve_sdram(void);

arch/arm/mach-omap1/opp.h

+/*
+ *  linux/arch/arm/mach-omap1/opp.h
+ *
+ *  Copyright (C) 2004 - 2005 Nokia corporation
+ *  Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
+ *  Based on clocks.h by Tony Lindgren, Gordon McNutt and RidgeRun, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP1_OPP_H
+#define __ARCH_ARM_MACH_OMAP1_OPP_H
+
+#include <linux/types.h>
+
+struct mpu_rate {
+	unsigned long		rate;
+	unsigned long		xtal;
+	unsigned long		pll_rate;
+	__u16			ckctl_val;
+	__u16			dpllctl_val;
+};
+
+extern struct mpu_rate omap1_rate_table[];
+
+#endif

arch/arm/mach-omap1/opp_data.c

+/*
+ *  linux/arch/arm/mach-omap1/opp_data.c
+ *
+ *  Copyright (C) 2004 - 2005 Nokia corporation
+ *  Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
+ *  Based on clocks.h by Tony Lindgren, Gordon McNutt and RidgeRun, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "opp.h"
+
+/*-------------------------------------------------------------------------
+ * Omap1 MPU rate table
+ *-------------------------------------------------------------------------*/
+struct mpu_rate omap1_rate_table[] = {
+	/* MPU MHz, xtal MHz, dpll1 MHz, CKCTL, DPLL_CTL
+	 * NOTE: Comment order here is different from bits in CKCTL value:
+	 * armdiv, dspdiv, dspmmu, tcdiv, perdiv, lcddiv
+	 */
+#if defined(CONFIG_OMAP_ARM_216MHZ)
+	{ 216000000, 12000000, 216000000, 0x050d, 0x2910 }, /* 1/1/2/2/2/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_195MHZ)
+	{ 195000000, 13000000, 195000000, 0x050e, 0x2790 }, /* 1/1/2/2/4/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_192MHZ)
+	{ 192000000, 19200000, 192000000, 0x050f, 0x2510 }, /* 1/1/2/2/8/8 */
+	{ 192000000, 12000000, 192000000, 0x050f, 0x2810 }, /* 1/1/2/2/8/8 */
+	{  96000000, 12000000, 192000000, 0x055f, 0x2810 }, /* 2/2/2/2/8/8 */
+	{  48000000, 12000000, 192000000, 0x0baf, 0x2810 }, /* 4/4/4/8/8/8 */
+	{  24000000, 12000000, 192000000, 0x0fff, 0x2810 }, /* 8/8/8/8/8/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_182MHZ)
+	{ 182000000, 13000000, 182000000, 0x050e, 0x2710 }, /* 1/1/2/2/4/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_168MHZ)
+	{ 168000000, 12000000, 168000000, 0x010f, 0x2710 }, /* 1/1/1/2/8/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_150MHZ)
+	{ 150000000, 12000000, 150000000, 0x010a, 0x2cb0 }, /* 1/1/1/2/4/4 */
+#endif
+#if defined(CONFIG_OMAP_ARM_120MHZ)
+	{ 120000000, 12000000, 120000000, 0x010a, 0x2510 }, /* 1/1/1/2/4/4 */
+#endif
+#if defined(CONFIG_OMAP_ARM_96MHZ)
+	{  96000000, 12000000,  96000000, 0x0005, 0x2410 }, /* 1/1/1/1/2/2 */
+#endif
+#if defined(CONFIG_OMAP_ARM_60MHZ)
+	{  60000000, 12000000,  60000000, 0x0005, 0x2290 }, /* 1/1/1/1/2/2 */
+#endif
+#if defined(CONFIG_OMAP_ARM_30MHZ)
+	{  30000000, 12000000,  60000000, 0x0555, 0x2290 }, /* 2/2/2/2/2/2 */
+#endif
+	{ 0, 0, 0, 0, 0 },
+};
+

arch/arm/mach-omap2/Kconfig

@@ -128,3 +128,15 @@ config OMAP3_EMU
 	help
 	  Say Y here to enable debugging hardware of omap3
 
+config OMAP3_SDRC_AC_TIMING
+	bool "Enable SDRC AC timing register changes"
+	depends on ARCH_OMAP3 && ARCH_OMAP34XX
+	default n
+	help
+	  If you know that none of your system initiators will attempt to
+	  access SDRAM during CORE DVFS, select Y here.  This should boost
+	  SDRAM performance at lower CORE OPPs.  There are relatively few
+	  users who will wish to say yes at this point - almost everyone will
+	  wish to say no.  Selecting yes without understanding what is
+	  going on could result in system crashes;
+

arch/arm/mach-omap2/Makefile

@@ -6,11 +6,14 @@
 obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer-gp.o
 
 omap-2-3-common				= irq.o sdrc.o omap_hwmod.o
+omap-3-4-common				= dpll.o
 prcm-common				= prcm.o powerdomain.o
-clock-common				= clock.o clockdomain.o
+clock-common				= clock.o clock_common_data.o clockdomain.o
 
 obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(prcm-common) $(clock-common)
-obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(prcm-common) $(clock-common)
+obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(prcm-common) $(clock-common) \
+			    $(omap-3-4-common)
+obj-$(CONFIG_ARCH_OMAP4) += $(omap-3-4-common) prcm.o clock.o
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
@@ -41,8 +44,11 @@ obj-$(CONFIG_ARCH_OMAP3)		+= cm.o
 obj-$(CONFIG_ARCH_OMAP4)		+= cm4xxx.o
 
 # Clock framework
-obj-$(CONFIG_ARCH_OMAP2)		+= clock24xx.o
-obj-$(CONFIG_ARCH_OMAP3)		+= clock34xx.o
+obj-$(CONFIG_ARCH_OMAP2)		+= clock2xxx.o clock2xxx_data.o
+obj-$(CONFIG_ARCH_OMAP2420)		+= opp2420_data.o
+obj-$(CONFIG_ARCH_OMAP3)		+= clock34xx.o clock34xx_data.o
+obj-$(CONFIG_ARCH_OMAP2430)		+= opp2430_data.o
+obj-$(CONFIG_ARCH_OMAP4)		+= clock44xx.o clock44xx_data.o
 
 # EMU peripherals
 obj-$(CONFIG_OMAP3_EMU)		+= emu.o

arch/arm/mach-omap2/clock.c

@@ -70,9 +70,41 @@
 u8 cpu_mask;
 
 /*-------------------------------------------------------------------------
- * OMAP2/3 specific clock functions
+ * OMAP2/3/4 specific clock functions
  *-------------------------------------------------------------------------*/
 
+void omap2_init_dpll_parent(struct clk *clk)
+{
+	u32 v;
+	struct dpll_data *dd;
+
+	dd = clk->dpll_data;
+	if (!dd)
+		return;
+
+	/* Return bypass rate if DPLL is bypassed */
+	v = __raw_readl(dd->control_reg);
+	v &= dd->enable_mask;
+	v >>= __ffs(dd->enable_mask);
+
+	/* Reparent in case the dpll is in bypass */
+	if (cpu_is_omap24xx()) {
+		if (v == OMAP2XXX_EN_DPLL_LPBYPASS ||
+		    v == OMAP2XXX_EN_DPLL_FRBYPASS)
+			clk_reparent(clk, dd->clk_bypass);
+	} else if (cpu_is_omap34xx()) {
+		if (v == OMAP3XXX_EN_DPLL_LPBYPASS ||
+		    v == OMAP3XXX_EN_DPLL_FRBYPASS)
+			clk_reparent(clk, dd->clk_bypass);
+	} else if (cpu_is_omap44xx()) {
+		if (v == OMAP4XXX_EN_DPLL_LPBYPASS ||
+		    v == OMAP4XXX_EN_DPLL_FRBYPASS ||
+		    v == OMAP4XXX_EN_DPLL_MNBYPASS)
+			clk_reparent(clk, dd->clk_bypass);
+	}
+	return;
+}
+
 /**
  * _omap2xxx_clk_commit - commit clock parent/rate changes in hardware
  * @clk: struct clk *
@@ -149,6 +181,7 @@ static int _dpll_test_fint(struct clk *clk, u8 n)
  * clockdomain pointer, and save it into the struct clk.  Intended to be
  * called during clk_register().  No return value.
  */
+#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once clkdm f/w is in place */
 void omap2_init_clk_clkdm(struct clk *clk)
 {
 	struct clockdomain *clkdm;
@@ -166,6 +199,7 @@ void omap2_init_clk_clkdm(struct clk *clk)
 			 "clkdm %s\n", clk->name, clk->clkdm_name);
 	}
 }
+#endif
 
 /**
  * omap2_init_clksel_parent - set a clksel clk's parent field from the hardware
@@ -247,6 +281,11 @@ u32 omap2_get_dpll_rate(struct clk *clk)
 		if (v == OMAP3XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP3XXX_EN_DPLL_FRBYPASS)
 			return dd->clk_bypass->rate;
+	} else if (cpu_is_omap44xx()) {
+		if (v == OMAP4XXX_EN_DPLL_LPBYPASS ||
+		    v == OMAP4XXX_EN_DPLL_FRBYPASS ||
+		    v == OMAP4XXX_EN_DPLL_MNBYPASS)
+			return dd->clk_bypass->rate;
 	}
 
 	v = __raw_readl(dd->mult_div1_reg);
@@ -437,8 +476,10 @@ void omap2_clk_disable(struct clk *clk)
 		_omap2_clk_disable(clk);
 		if (clk->parent)
 			omap2_clk_disable(clk->parent);
+#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once clkdm f/w is in place */
 		if (clk->clkdm)
 			omap2_clkdm_clk_disable(clk->clkdm, clk);
+#endif
 
 	}
 }
@@ -448,8 +489,10 @@ int omap2_clk_enable(struct clk *clk)
 	int ret = 0;
 
 	if (clk->usecount++ == 0) {
+#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once clkdm f/w is in place */
 		if (clk->clkdm)
 			omap2_clkdm_clk_enable(clk->clkdm, clk);
+#endif
 
 		if (clk->parent) {
 			ret = omap2_clk_enable(clk->parent);
@@ -468,8 +511,10 @@ int omap2_clk_enable(struct clk *clk)
 	return ret;
 
 err:
+#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once clkdm f/w is in place */
 	if (clk->clkdm)
 		omap2_clkdm_clk_disable(clk->clkdm, clk);
+#endif
 	clk->usecount--;
 	return ret;
 }

arch/arm/mach-omap2/clock.h

 /*
  *  linux/arch/arm/mach-omap2/clock.h
  *
- *  Copyright (C) 2005-2008 Texas Instruments, Inc.
- *  Copyright (C) 2004-2008 Nokia Corporation
+ *  Copyright (C) 2005-2009 Texas Instruments, Inc.
+ *  Copyright (C) 2004-2009 Nokia Corporation
  *
  *  Contacts:
  *  Richard Woodruff <r-woodruff2@ti.com>
@@ -36,6 +36,17 @@
 #define OMAP3XXX_EN_DPLL_FRBYPASS		0x6
 #define OMAP3XXX_EN_DPLL_LOCKED			0x7
 
+/* OMAP4xxx CM_CLKMODE_DPLL*.EN_*_DPLL bits - for omap2_get_dpll_rate() */
+#define OMAP4XXX_EN_DPLL_MNBYPASS		0x4
+#define OMAP4XXX_EN_DPLL_LPBYPASS		0x5
+#define OMAP4XXX_EN_DPLL_FRBYPASS		0x6
+#define OMAP4XXX_EN_DPLL_LOCKED			0x7
+
+/* CM_CLKEN_PLL*.EN* bit values - not all are available for every DPLL */
+#define DPLL_LOW_POWER_STOP	0x1
+#define DPLL_LOW_POWER_BYPASS	0x5
+#define DPLL_LOCKED		0x7
+
 int omap2_clk_init(void);
 int omap2_clk_enable(struct clk *clk);
 void omap2_clk_disable(struct clk *clk);
@@ -44,6 +55,14 @@ int omap2_clk_set_rate(struct clk *clk, unsigned long rate);
 int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent);
 int omap2_dpll_set_rate_tolerance(struct clk *clk, unsigned int tolerance);
 long omap2_dpll_round_rate(struct clk *clk, unsigned long target_rate);
+unsigned long omap3_dpll_recalc(struct clk *clk);
+unsigned long omap3_clkoutx2_recalc(struct clk *clk);
+void omap3_dpll_allow_idle(struct clk *clk);
+void omap3_dpll_deny_idle(struct clk *clk);
+u32 omap3_dpll_autoidle_read(struct clk *clk);
+int omap3_noncore_dpll_set_rate(struct clk *clk, unsigned long rate);
+int omap3_noncore_dpll_enable(struct clk *clk);
+void omap3_noncore_dpll_disable(struct clk *clk);
 
 #ifdef CONFIG_OMAP_RESET_CLOCKS
 void omap2_clk_disable_unused(struct clk *clk);
@@ -63,6 +82,7 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk);
 long omap2_clksel_round_rate(struct clk *clk, unsigned long target_rate);
 int omap2_clksel_set_rate(struct clk *clk, unsigned long rate);
 u32 omap2_get_dpll_rate(struct clk *clk);
+void omap2_init_dpll_parent(struct clk *clk);
 int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name);
 void omap2_clk_prepare_for_reboot(void);
 int omap2_dflt_clk_enable(struct clk *clk);
@@ -72,29 +92,17 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
 void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
 				u8 *idlest_bit);
 
+extern u8 cpu_mask;
+
 extern const struct clkops clkops_omap2_dflt_wait;
 extern const struct clkops clkops_omap2_dflt;
 
-extern u8 cpu_mask;
+extern struct clk_functions omap2_clk_functions;
+extern struct clk *vclk, *sclk;
 
-/* clksel_rate data common to 24xx/343x */
-static const struct clksel_rate gpt_32k_rates[] = {
-	 { .div = 1, .val = 0, .flags = RATE_IN_24XX | RATE_IN_343X | DEFAULT_RATE },
-	 { .div = 0 }
-};
-
-static const struct clksel_rate gpt_sys_rates[] = {
-	 { .div = 1, .val = 1, .flags = RATE_IN_24XX | RATE_IN_343X | DEFAULT_RATE },
-	 { .div = 0 }
-};
-
-static const struct clksel_rate gfx_l3_rates[] = {
-	{ .div = 1, .val = 1, .flags = RATE_IN_24XX | RATE_IN_343X },
-	{ .div = 2, .val = 2, .flags = RATE_IN_24XX | RATE_IN_343X | DEFAULT_RATE },
-	{ .div = 3, .val = 3, .flags = RATE_IN_243X | RATE_IN_343X },
-	{ .div = 4, .val = 4, .flags = RATE_IN_243X | RATE_IN_343X },
-	{ .div = 0 }
-};
+extern const struct clksel_rate gpt_32k_rates[];
+extern const struct clksel_rate gpt_sys_rates[];
+extern const struct clksel_rate gfx_l3_rates[];
 
 
 #endif

arch/arm/mach-omap2/clock2xxx.h

+/*
+ * OMAP2 clock function prototypes and macros
+ *
+ * Copyright (C) 2005-2009 Texas Instruments, Inc.
+ * Copyright (C) 2004-2009 Nokia Corporation
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK_24XX_H
+#define __ARCH_ARM_MACH_OMAP2_CLOCK_24XX_H
+
+unsigned long omap2_table_mpu_recalc(struct clk *clk);
+int omap2_select_table_rate(struct clk *clk, unsigned long rate);
+long omap2_round_to_table_rate(struct clk *clk, unsigned long rate);
+unsigned long omap2_sys_clk_recalc(struct clk *clk);
+unsigned long omap2_osc_clk_recalc(struct clk *clk);
+unsigned long omap2_sys_clk_recalc(struct clk *clk);
+unsigned long omap2_dpllcore_recalc(struct clk *clk);
+int omap2_reprogram_dpllcore(struct clk *clk, unsigned long rate);
+unsigned long omap2xxx_clk_get_core_rate(struct clk *clk);
+
+/* REVISIT: These should be set dynamically for CONFIG_MULTI_OMAP2 */
+#ifdef CONFIG_ARCH_OMAP2420
+#define OMAP_CM_REGADDR			OMAP2420_CM_REGADDR
+#define OMAP24XX_PRCM_CLKOUT_CTRL	OMAP2420_PRCM_CLKOUT_CTRL
+#define OMAP24XX_PRCM_CLKEMUL_CTRL	OMAP2420_PRCM_CLKEMUL_CTRL
+#else
+#define OMAP_CM_REGADDR			OMAP2430_CM_REGADDR
+#define OMAP24XX_PRCM_CLKOUT_CTRL	OMAP2430_PRCM_CLKOUT_CTRL
+#define OMAP24XX_PRCM_CLKEMUL_CTRL	OMAP2430_PRCM_CLKEMUL_CTRL
+#endif
+
+extern void __iomem *prcm_clksrc_ctrl;
+
+extern struct clk *dclk;
+
+extern const struct clkops clkops_omap2430_i2chs_wait;
+extern const struct clkops clkops_oscck;
+extern const struct clkops clkops_apll96;
+extern const struct clkops clkops_apll54;
+
+#endif

arch/arm/mach-omap2/clock44xx.c

+/*
+ * OMAP4-specific clock framework functions
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Rajendra Nayak (rnayak@ti.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/errno.h>
+#include "clock.h"
+
+struct clk_functions omap2_clk_functions = {
+	.clk_enable		= omap2_clk_enable,
+	.clk_disable		= omap2_clk_disable,
+	.clk_round_rate		= omap2_clk_round_rate,
+	.clk_set_rate		= omap2_clk_set_rate,
+	.clk_set_parent		= omap2_clk_set_parent,
+	.clk_disable_unused	= omap2_clk_disable_unused,
+};
+
+const struct clkops clkops_noncore_dpll_ops = {
+	.enable		= &omap3_noncore_dpll_enable,
+	.disable	= &omap3_noncore_dpll_disable,
+};
+
+void omap2_clk_prepare_for_reboot(void)
+{
+	return;
+}

arch/arm/mach-omap2/clock44xx.h

+/*
+ * OMAP4 clock function prototypes and macros
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK_44XX_H
+#define __ARCH_ARM_MACH_OMAP2_CLOCK_44XX_H
+
+#define OMAP4430_MAX_DPLL_MULT	2048
+#define OMAP4430_MAX_DPLL_DIV	128
+
+extern const struct clkops clkops_noncore_dpll_ops;
+
+#endif

arch/arm/mach-omap2/clock_common_data.c

+/*
+ *  linux/arch/arm/mach-omap2/clock_common_data.c
+ *
+ *  Copyright (C) 2005-2009 Texas Instruments, Inc.
+ *  Copyright (C) 2004-2009 Nokia Corporation
+ *
+ *  Contacts:
+ *  Richard Woodruff <r-woodruff2@ti.com>
+ *  Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This file contains clock data that is common to both the OMAP2xxx and
+ * OMAP3xxx clock definition files.
+ */
+
+#include "clock.h"
+
+/* clksel_rate data common to 24xx/343x */
+const struct clksel_rate gpt_32k_rates[] = {
+	 { .div = 1, .val = 0, .flags = RATE_IN_24XX | RATE_IN_343X | DEFAULT_RATE },
+	 { .div = 0 }
+};
+
+const struct clksel_rate gpt_sys_rates[] = {
+	 { .div = 1, .val = 1, .flags = RATE_IN_24XX | RATE_IN_343X | DEFAULT_RATE },
+	 { .div = 0 }
+};
+
+const struct clksel_rate gfx_l3_rates[] = {
+	{ .div = 1, .val = 1, .flags = RATE_IN_24XX | RATE_IN_343X },
+	{ .div = 2, .val = 2, .flags = RATE_IN_24XX | RATE_IN_343X | DEFAULT_RATE },
+	{ .div = 3, .val = 3, .flags = RATE_IN_243X | RATE_IN_343X },
+	{ .div = 4, .val = 4, .flags = RATE_IN_243X | RATE_IN_343X },
+	{ .div = 0 }
+};
+

arch/arm/mach-omap2/clockdomain.c

@@ -2,7 +2,7 @@
  * OMAP2/3 clockdomain framework functions
  *
  * Copyright (C) 2008 Texas Instruments, Inc.
- * Copyright (C) 2008 Nokia Corporation
+ * Copyright (C) 2008-2009 Nokia Corporation
  *
  * Written by Paul Walmsley and Jouni Högander
  *
@@ -10,9 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-#ifdef CONFIG_OMAP_DEBUG_CLOCKDOMAIN
-#  define DEBUG
-#endif
+#undef DEBUG
 
 #include <linux/module.h>
 #include <linux/kernel.h>

arch/arm/mach-omap2/cm.c

@@ -21,6 +21,8 @@
 
 #include <asm/atomic.h>
 
+#include <plat/common.h>
+
 #include "cm.h"
 #include "cm-regbits-24xx.h"
 #include "cm-regbits-34xx.h"
@@ -61,9 +63,8 @@ int omap2_cm_wait_module_ready(s16 prcm_mod, u8 idlest_id, u8 idlest_shift)
 	mask = 1 << idlest_shift;
 
 	/* XXX should be OMAP2 CM */
-	while (((cm_read_mod_reg(prcm_mod, cm_idlest_reg) & mask) != ena) &&
-	       (i++ < MAX_MODULE_READY_TIME))
-		udelay(1);
+	omap_test_timeout(((cm_read_mod_reg(prcm_mod, cm_idlest_reg) & mask) == ena),
+			  MAX_MODULE_READY_TIME, i);
 
 	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
 }

arch/arm/mach-omap2/cm.h

@@ -4,8 +4,8 @@
 /*
  * OMAP2/3 Clock Management (CM) register definitions
  *
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
+ * Copyright (C) 2007-2009 Texas Instruments, Inc.
+ * Copyright (C) 2007-2009 Nokia Corporation
  *
  * Written by Paul Walmsley
  *
@@ -22,6 +22,12 @@
 			OMAP2_L4_IO_ADDRESS(OMAP2430_CM_BASE + (module) + (reg))
 #define OMAP34XX_CM_REGADDR(module, reg)				\
 			OMAP2_L4_IO_ADDRESS(OMAP3430_CM_BASE + (module) + (reg))
+#define OMAP44XX_CM1_REGADDR(module, reg)				\
+			OMAP2_L4_IO_ADDRESS(OMAP4430_CM1_BASE + (module) + (reg))
+#define OMAP44XX_CM2_REGADDR(module, reg)				\
+			OMAP2_L4_IO_ADDRESS(OMAP4430_CM2_BASE + (module) + (reg))
+
+#include "cm44xx.h"
 
 /*
  * Architecture-specific global CM registers
@@ -89,6 +95,11 @@
 #define OMAP3430_CM_CLKSEL2_EMU				0x0050
 #define OMAP3430_CM_CLKSEL3_EMU				0x0054
 
+/* CM2.CEFUSE_CM2 register offsets */
+
+/* OMAP4 modulemode control */
+#define OMAP4430_MODULEMODE_HWCTRL			0
+#define OMAP4430_MODULEMODE_SWCTRL			1
 
 /* Clock management domain register get/set */
 

arch/arm/mach-omap2/gpmc.c

@@ -517,7 +517,7 @@ void __init gpmc_init(void)
 		ck = "gpmc_fck";
 		l = OMAP34XX_GPMC_BASE;
 	} else if (cpu_is_omap44xx()) {
-		ck = "gpmc_fck";
+		ck = "gpmc_ck";
 		l = OMAP44XX_GPMC_BASE;
 	}
 

arch/arm/mach-omap2/io.c

@@ -35,7 +35,6 @@
 #include <plat/serial.h>
 #include <plat/vram.h>
 
-#ifndef CONFIG_ARCH_OMAP4	/* FIXME: Remove this once clkdev is ready */
 #include "clock.h"
 
 #include <plat/omap-pm.h>
@@ -44,7 +43,6 @@
 
 #include <plat/clockdomain.h>
 #include "clockdomains.h"
-#endif
 #include <plat/omap_hwmod.h>
 #include "omap_hwmod_2420.h"
 #include "omap_hwmod_2430.h"
@@ -321,8 +319,8 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
 	pwrdm_init(powerdomains_omap);
 	clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
-	omap2_clk_init();
 #endif
+	omap2_clk_init();
 	omap_serial_early_init();
 #ifndef CONFIG_ARCH_OMAP4
 	omap_hwmod_late_init();

arch/arm/mach-omap2/omap_hwmod.c

@@ -45,6 +45,7 @@
 #include <linux/mutex.h>
 #include <linux/bootmem.h>
 
+#include <plat/common.h>
 #include <plat/cpu.h>
 #include <plat/clockdomain.h>
 #include <plat/powerdomain.h>
@@ -209,6 +210,32 @@ static int _set_softreset(struct omap_hwmod *oh, u32 *v)
 	return 0;
 }
 
+/**
+ * _set_module_autoidle: set the OCP_SYSCONFIG AUTOIDLE field in @v
+ * @oh: struct omap_hwmod *
+ * @autoidle: desired AUTOIDLE bitfield value (0 or 1)
+ * @v: pointer to register contents to modify
+ *
+ * Update the module autoidle bit in @v to be @autoidle for the @oh
+ * hwmod.  The autoidle bit controls whether the module can gate
+ * internal clocks automatically when it isn't doing anything; the
+ * exact function of this bit varies on a per-module basis.  This
+ * function does not write to the hardware.  Returns -EINVAL upon
+ * error or 0 upon success.
+ */
+static int _set_module_autoidle(struct omap_hwmod *oh, u8 autoidle,
+				u32 *v)
+{
+	if (!oh->sysconfig ||
+	    !(oh->sysconfig->sysc_flags & SYSC_HAS_AUTOIDLE))
+		return -EINVAL;
+
+	*v &= ~SYSC_AUTOIDLE_MASK;
+	*v |= autoidle << SYSC_AUTOIDLE_SHIFT;
+
+	return 0;
+}
+
 /**
  * _enable_wakeup: set OCP_SYSCONFIG.ENAWAKEUP bit in the hardware
  * @oh: struct omap_hwmod *
@@ -326,6 +353,9 @@ static int _init_main_clk(struct omap_hwmod *oh)
 		ret = -EINVAL;
 	oh->_clk = c;
 
+	WARN(!c->clkdm, "omap_hwmod: %s: missing clockdomain for %s.\n",
+	     oh->clkdev_con_id, c->name);
+
 	return ret;
 }
 
@@ -557,8 +587,19 @@ static void _sysc_enable(struct omap_hwmod *oh)
 		_set_master_standbymode(oh, idlemode, &v);
 	}
 
-	/* XXX OCP AUTOIDLE bit? */
+	if (oh->sysconfig->sysc_flags & SYSC_HAS_AUTOIDLE) {
+		idlemode = (oh->flags & HWMOD_NO_OCP_AUTOIDLE) ?
+			0 : 1;
+		_set_module_autoidle(oh, idlemode, &v);
+	}
+
+	/* XXX OCP ENAWAKEUP bit? */
 
+	/*
+	 * XXX The clock framework should handle this, by
+	 * calling into this code.  But this must wait until the
+	 * clock structures are tagged with omap_hwmod entries
+	 */
 	if (oh->flags & HWMOD_SET_DEFAULT_CLOCKACT &&
 	    oh->sysconfig->sysc_flags & SYSC_HAS_CLOCKACTIVITY)
 		_set_clockactivity(oh, oh->sysconfig->clockact, &v);
@@ -622,7 +663,8 @@ static void _sysc_shutdown(struct omap_hwmod *oh)
 	if (oh->sysconfig->sysc_flags & SYSC_HAS_MIDLEMODE)
 		_set_master_standbymode(oh, HWMOD_IDLEMODE_FORCE, &v);
 
-	/* XXX clear OCP AUTOIDLE bit? */
+	if (oh->sysconfig->sysc_flags & SYSC_HAS_AUTOIDLE)
+		_set_module_autoidle(oh, 1, &v);
 
 	_write_sysconfig(v, oh);
 }
@@ -736,7 +778,7 @@ static int _wait_target_ready(struct omap_hwmod *oh)
 static int _reset(struct omap_hwmod *oh)
 {
 	u32 r, v;
-	int c;
+	int c = 0;
 
 	if (!oh->sysconfig ||
 	    !(oh->sysconfig->sysc_flags & SYSC_HAS_SOFTRESET) ||
@@ -758,13 +800,9 @@ static int _reset(struct omap_hwmod *oh)
 		return r;
 	_write_sysconfig(v, oh);
 
-	c = 0;
-	while (c < MAX_MODULE_RESET_WAIT &&
-	       !(omap_hwmod_readl(oh, oh->sysconfig->syss_offs) &
-		 SYSS_RESETDONE_MASK)) {
-		udelay(1);
-		c++;
-	}
+	omap_test_timeout((omap_hwmod_readl(oh, oh->sysconfig->syss_offs) &
+			   SYSS_RESETDONE_MASK),
+			  MAX_MODULE_RESET_WAIT, c);
 
 	if (c == MAX_MODULE_RESET_WAIT)
 		WARN(1, "omap_hwmod: %s: failed to reset in %d usec\n",
@@ -883,33 +921,6 @@ static int _shutdown(struct omap_hwmod *oh)
 	return 0;
 }
 
-/**
- * _write_clockact_lock - set the module's clockactivity bits
- * @oh: struct omap_hwmod *
- * @clockact: CLOCKACTIVITY field bits
- *
- * Writes the CLOCKACTIVITY bits @clockact to the hwmod @oh
- * OCP_SYSCONFIG register.  Returns -EINVAL if the hwmod is in the
- * wrong state or returns 0.
- */
-static int _write_clockact_lock(struct omap_hwmod *oh, u8 clockact)
-{
-	u32 v;
-
-	if (!oh->sysconfig ||
-	    !(oh->sysconfig->sysc_flags & SYSC_HAS_CLOCKACTIVITY))
-		return -EINVAL;
-
-	mutex_lock(&omap_hwmod_mutex);
-	v = oh->_sysc_cache;
-	_set_clockactivity(oh, clockact, &v);
-	_write_sysconfig(v, oh);
-	mutex_unlock(&omap_hwmod_mutex);
-
-	return 0;
-}
-
-
 /**
  * _setup - do initial configuration of omap_hwmod
  * @oh: struct omap_hwmod *
@@ -948,11 +959,19 @@ static int _setup(struct omap_hwmod *oh)
 
 	_enable(oh);
 
-	if (!(oh->flags & HWMOD_INIT_NO_RESET))
-		_reset(oh);
-
-	/* XXX OCP AUTOIDLE bit? */
-	/* XXX OCP ENAWAKEUP bit? */
+	if (!(oh->flags & HWMOD_INIT_NO_RESET)) {
+		/*
+		 * XXX Do the OCP_SYSCONFIG bits need to be
+		 * reprogrammed after a reset?  If not, then this can
+		 * be removed.  If they do, then probably the
+		 * _enable() function should be split to avoid the
+		 * rewrite of the OCP_SYSCONFIG register.
+		 */
+		if (oh->sysconfig) {
+			_update_sysc_cache(oh);
+			_sysc_enable(oh);
+		}
+	}
 
 	if (!(oh->flags & HWMOD_INIT_NO_IDLE))
 		_idle(oh);
@@ -1348,8 +1367,9 @@ int omap_hwmod_fill_resources(struct omap_hwmod *oh, struct resource *res)
 	/* For each IRQ, DMA, memory area, fill in array.*/
 
 	for (i = 0; i < oh->mpu_irqs_cnt; i++) {
-		(res + r)->start = *(oh->mpu_irqs + i);
-		(res + r)->end = *(oh->mpu_irqs + i);
+		(res + r)->name = (oh->mpu_irqs + i)->name;
+		(res + r)->start = (oh->mpu_irqs + i)->irq;
+		(res + r)->end = (oh->mpu_irqs + i)->irq;
 		(res + r)->flags = IORESOURCE_IRQ;
 		r++;
 	}
@@ -1453,62 +1473,6 @@ int omap_hwmod_del_initiator_dep(struct omap_hwmod *oh,
 	return _del_initiator_dep(oh, init_oh);
 }
 
-/**
- * omap_hwmod_set_clockact_none - set clockactivity test to BOTH
- * @oh: struct omap_hwmod *
- *
- * On some modules, this function can affect the wakeup latency vs.
- * power consumption balance.  Intended to be called by the
- * omap_device layer.  Passes along the return value from
- * _write_clockact_lock().
- */
-int omap_hwmod_set_clockact_both(struct omap_hwmod *oh)
-{
-	return _write_clockact_lock(oh, CLOCKACT_TEST_BOTH);
-}
-
-/**
- * omap_hwmod_set_clockact_none - set clockactivity test to MAIN
- * @oh: struct omap_hwmod *
- *
- * On some modules, this function can affect the wakeup latency vs.
- * power consumption balance.  Intended to be called by the
- * omap_device layer.  Passes along the return value from
- * _write_clockact_lock().
- */
-int omap_hwmod_set_clockact_main(struct omap_hwmod *oh)
-{
-	return _write_clockact_lock(oh, CLOCKACT_TEST_MAIN);
-}
-
-/**
- * omap_hwmod_set_clockact_none - set clockactivity test to ICLK
- * @oh: struct omap_hwmod *
- *
- * On some modules, this function can affect the wakeup latency vs.
- * power consumption balance.  Intended to be called by the
- * omap_device layer.  Passes along the return value from
- * _write_clockact_lock().
- */
-int omap_hwmod_set_clockact_iclk(struct omap_hwmod *oh)
-{
-	return _write_clockact_lock(oh, CLOCKACT_TEST_ICLK);
-}
-
-/**
- * omap_hwmod_set_clockact_none - set clockactivity test to NONE
- * @oh: struct omap_hwmod *
- *
- * On some modules, this function can affect the wakeup latency vs.
- * power consumption balance.  Intended to be called by the
- * omap_device layer.  Passes along the return value from
- * _write_clockact_lock().
- */
-int omap_hwmod_set_clockact_none(struct omap_hwmod *oh)
-{
-	return _write_clockact_lock(oh, CLOCKACT_TEST_NONE);
-}
-
 /**
  * omap_hwmod_enable_wakeup - allow device to wake up the system
  * @oh: struct omap_hwmod *

arch/arm/mach-omap2/opp2420_data.c

+/*
+ * opp2420_data.c - old-style "OPP" table for OMAP2420
+ *
+ * Copyright (C) 2005-2009 Texas Instruments, Inc.
+ * Copyright (C) 2004-2009 Nokia Corporation
+ *
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * The OMAP2 processor can be run at several discrete 'PRCM configurations'.
+ * These configurations are characterized by voltage and speed for clocks.
+ * The device is only validated for certain combinations. One way to express
+ * these combinations is via the 'ratio's' which the clocks operate with
+ * respect to each other. These ratio sets are for a given voltage/DPLL
+ * setting. All configurations can be described by a DPLL setting and a ratio
+ * There are 3 ratio sets for the 2430 and X ratio sets for 2420.
+ *
+ * 2430 differs from 2420 in that there are no more phase synchronizers used.
+ * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs
+ * 2430 (iva2.1, NOdsp, mdm)
+ *
+ * XXX Missing voltage data.
+ *
+ * THe format described in this file is deprecated.  Once a reasonable
+ * OPP API exists, the data in this file should be converted to use it.
+ *
+ * This is technically part of the OMAP2xxx clock code.
+ */
+
+#include "opp2xxx.h"
+#include "sdrc.h"
+#include "clock.h"
+
+/*-------------------------------------------------------------------------
+ * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated.
+ * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,
+ * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL,
+ * CM_CLKSEL2_PLL, CM_CLKSEL_MDM
+ *
+ * Filling in table based on H4 boards and 2430-SDPs variants available.
+ * There are quite a few more rates combinations which could be defined.
+ *
+ * When multiple values are defined the start up will try and choose the
+ * fastest one. If a 'fast' value is defined, then automatically, the /2
+ * one should be included as it can be used.	Generally having more that
+ * one fast set does not make sense, as static timings need to be changed
+ * to change the set.	 The exception is the bypass setting which is
+ * availble for low power bypass.
+ *
+ * Note: This table needs to be sorted, fastest to slowest.
+ *-------------------------------------------------------------------------*/
+const struct prcm_config omap2420_rate_table[] = {
+	/* PRCM I - FAST */
+	{S12M, S660M, S330M, RI_CM_CLKSEL_MPU_VAL,		/* 330MHz ARM */
+		RI_CM_CLKSEL_DSP_VAL, RI_CM_CLKSEL_GFX_VAL,
+		RI_CM_CLKSEL1_CORE_VAL, MI_CM_CLKSEL1_PLL_12_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_165MHz,
+		RATE_IN_242X},
+
+	/* PRCM II - FAST */
+	{S12M, S600M, S300M, RII_CM_CLKSEL_MPU_VAL,		/* 300MHz ARM */
+		RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL,
+		RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_12_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz,
+		RATE_IN_242X},
+
+	{S13M, S600M, S300M, RII_CM_CLKSEL_MPU_VAL,		/* 300MHz ARM */
+		RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL,
+		RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_13_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz,
+		RATE_IN_242X},
+
+	/* PRCM III - FAST */
+	{S12M, S532M, S266M, RIII_CM_CLKSEL_MPU_VAL,		/* 266MHz ARM */
+		RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL,
+		RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_12_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz,
+		RATE_IN_242X},
+
+	{S13M, S532M, S266M, RIII_CM_CLKSEL_MPU_VAL,		/* 266MHz ARM */
+		RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL,
+		RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_13_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz,
+		RATE_IN_242X},
+
+	/* PRCM II - SLOW */
+	{S12M, S300M, S150M, RII_CM_CLKSEL_MPU_VAL,		/* 150MHz ARM */
+		RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL,
+		RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_12_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz,
+		RATE_IN_242X},
+
+	{S13M, S300M, S150M, RII_CM_CLKSEL_MPU_VAL,		/* 150MHz ARM */
+		RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL,
+		RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_13_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz,
+		RATE_IN_242X},
+
+	/* PRCM III - SLOW */
+	{S12M, S266M, S133M, RIII_CM_CLKSEL_MPU_VAL,		/* 133MHz ARM */
+		RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL,
+		RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_12_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz,
+		RATE_IN_242X},
+
+	{S13M, S266M, S133M, RIII_CM_CLKSEL_MPU_VAL,		/* 133MHz ARM */
+		RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL,
+		RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_13_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz,
+		RATE_IN_242X},
+
+	/* PRCM-VII (boot-bypass) */
+	{S12M, S12M, S12M, RVII_CM_CLKSEL_MPU_VAL,		/* 12MHz ARM*/
+		RVII_CM_CLKSEL_DSP_VAL, RVII_CM_CLKSEL_GFX_VAL,
+		RVII_CM_CLKSEL1_CORE_VAL, MVII_CM_CLKSEL1_PLL_12_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_BYPASS,
+		RATE_IN_242X},
+
+	/* PRCM-VII (boot-bypass) */
+	{S13M, S13M, S13M, RVII_CM_CLKSEL_MPU_VAL,		/* 13MHz ARM */
+		RVII_CM_CLKSEL_DSP_VAL, RVII_CM_CLKSEL_GFX_VAL,
+		RVII_CM_CLKSEL1_CORE_VAL, MVII_CM_CLKSEL1_PLL_13_VAL,
+		MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_BYPASS,
+		RATE_IN_242X},
+
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},
+};

arch/arm/mach-omap2/pm-debug.c

@@ -326,7 +326,7 @@ int pm_dbg_regset_save(int reg_set)
 	return 0;
 }
 
-static const char pwrdm_state_names[][4] = {
+static const char pwrdm_state_names[][PWRDM_MAX_PWRSTS] = {
 	"OFF",
 	"RET",
 	"INA",
@@ -381,7 +381,7 @@ static int pwrdm_dbg_show_counter(struct powerdomain *pwrdm, void *user)
 
 	seq_printf(s, "%s (%s)", pwrdm->name,
 			pwrdm_state_names[pwrdm->state]);
-	for (i = 0; i < 4; i++)
+	for (i = 0; i < PWRDM_MAX_PWRSTS; i++)
 		seq_printf(s, ",%s:%d", pwrdm_state_names[i],
 			pwrdm->state_counter[i]);
 

arch/arm/mach-omap2/powerdomains34xx.h

@@ -190,6 +190,7 @@ static struct powerdomain mpu_34xx_pwrdm = {
 	.wkdep_srcs	  = mpu_34xx_wkdeps,
 	.pwrsts		  = PWRSTS_OFF_RET_ON,
 	.pwrsts_logic_ret = PWRSTS_OFF_RET,
+	.flags		  = PWRDM_HAS_MPU_QUIRK,
 	.banks		  = 1,
 	.pwrsts_mem_ret	  = {
 		[0] = PWRSTS_OFF_RET,

arch/arm/mach-omap2/prcm-common.h

@@ -4,10 +4,12 @@
 /*
  * OMAP2/3 PRCM base and module definitions
  *
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
+ * Copyright (C) 2007-2009 Texas Instruments, Inc.
+ * Copyright (C) 2007-2009 Nokia Corporation
  *
  * Written by Paul Walmsley
+ * OMAP4 defines in this file are automatically generated from the OMAP hardware
+ * databases.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -49,6 +51,73 @@
 #define OMAP3430_NEON_MOD				0xb00
 #define OMAP3430ES2_USBHOST_MOD				0xc00
 
+#define BITS(n_bit)	\
+	(((1 << n_bit) - 1) | (1 << n_bit))
+
+#define BITFIELD(l_bit, u_bit)	\
+	(BITS(u_bit) & ~((BITS(l_bit)) >> 1))
+
+/* OMAP44XX specific module offsets */
+
+/* CM1 instances */
+
+#define OMAP4430_CM1_OCP_SOCKET_MOD	0x0000
+#define OMAP4430_CM1_CKGEN_MOD		0x0100
+#define OMAP4430_CM1_MPU_MOD		0x0300
+#define OMAP4430_CM1_TESLA_MOD		0x0400
+#define OMAP4430_CM1_ABE_MOD		0x0500
+#define OMAP4430_CM1_RESTORE_MOD	0x0e00
+#define OMAP4430_CM1_INSTR_MOD		0x0f00
+
+/* CM2 instances */
+
+#define OMAP4430_CM2_OCP_SOCKET_MOD	0x0000
+#define OMAP4430_CM2_CKGEN_MOD		0x0100
+#define OMAP4430_CM2_ALWAYS_ON_MOD	0x0600
+#define OMAP4430_CM2_CORE_MOD		0x0700
+#define OMAP4430_CM2_IVAHD_MOD		0x0f00
+#define OMAP4430_CM2_CAM_MOD		0x1000
+#define OMAP4430_CM2_DSS_MOD		0x1100
+#define OMAP4430_CM2_GFX_MOD		0x1200
+#define OMAP4430_CM2_L3INIT_MOD		0x1300
+#define OMAP4430_CM2_L4PER_MOD		0x1400
+#define OMAP4430_CM2_CEFUSE_MOD		0x1600
+#define OMAP4430_CM2_RESTORE_MOD	0x1e00
+#define OMAP4430_CM2_INSTR_MOD		0x1f00
+
+/* PRM instances */
+
+#define OMAP4430_PRM_OCP_SOCKET_MOD	0x0000
+#define OMAP4430_PRM_CKGEN_MOD		0x0100
+#define OMAP4430_PRM_MPU_MOD		0x0300
+#define OMAP4430_PRM_TESLA_MOD		0x0400
+#define OMAP4430_PRM_ABE_MOD		0x0500
+#define OMAP4430_PRM_ALWAYS_ON_MOD	0x0600
+#define OMAP4430_PRM_CORE_MOD		0x0700
+#define OMAP4430_PRM_IVAHD_MOD		0x0f00
+#define OMAP4430_PRM_CAM_MOD		0x1000
+#define OMAP4430_PRM_DSS_MOD		0x1100
+#define OMAP4430_PRM_GFX_MOD		0x1200
+#define OMAP4430_PRM_L3INIT_MOD		0x1300
+#define OMAP4430_PRM_L4PER_MOD		0x1400
+#define OMAP4430_PRM_CEFUSE_MOD		0x1600
+#define OMAP4430_PRM_WKUP_MOD		0x1700
+#define OMAP4430_PRM_WKUP_CM_MOD	0x1800
+#define OMAP4430_PRM_EMU_MOD		0x1900
+#define OMAP4430_PRM_EMU_CM_MOD		0x1a00
+#define OMAP4430_PRM_DEVICE_MOD		0x1b00
+#define OMAP4430_PRM_INSTR_MOD		0x1f00
+
+/* SCRM instances */
+
+#define OMAP4430_SCRM_SCRM_MOD	0x0000
+
+/* CHIRONSS instances */
+
+#define OMAP4430_CHIRONSS_CHIRONSS_OCP_SOCKET_PRCM_MOD	0x0000
+#define OMAP4430_CHIRONSS_CHIRONSS_DEVICE_PRM_MOD	0x0200
+#define OMAP4430_CHIRONSS_CHIRONSS_CPU0_MOD		0x0400
+#define OMAP4430_CHIRONSS_CHIRONSS_CPU1_MOD		0x0800
 
 /* 24XX register bits shared between CM & PRM registers */
 

arch/arm/mach-omap2/prm.h

@@ -4,8 +4,8 @@
 /*
  * OMAP2/3 Power/Reset Management (PRM) register definitions
  *
- * Copyright (C) 2007 Texas Instruments, Inc.
- * Copyright (C) 2007 Nokia Corporation
+ * Copyright (C) 2007-2009 Texas Instruments, Inc.
+ * Copyright (C) 2009 Nokia Corporation
  *
  * Written by Paul Walmsley
  *
@@ -22,6 +22,10 @@
 		OMAP2_L4_IO_ADDRESS(OMAP2430_PRM_BASE + (module) + (reg))
 #define OMAP34XX_PRM_REGADDR(module, reg)				\
 		OMAP2_L4_IO_ADDRESS(OMAP3430_PRM_BASE + (module) + (reg))
+#define OMAP44XX_PRM_REGADDR(module, reg)				\
+		OMAP2_L4_IO_ADDRESS(OMAP4430_PRM_BASE + (module) + (reg))
+
+#include "prm44xx.h"
 
 /*
  * Architecture-specific global PRM registers