arm64: dts: ls1028a: add missing LPUART nodes

The LS1028A has six LPUART controllers. Add the nodes.

This was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200307091302.14881-2-michael@walle.ccSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

@@ -333,6 +333,79 @@ duart1: serial@21c0600 {
 			status = "disabled";
 		};
 
+
+		lpuart0: serial@2260000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2260000 0x0 0x1000>;
+			interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 32>,
+			       <&edma0 1 33>;
+			status = "disabled";
+		};
+
+		lpuart1: serial@2270000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2270000 0x0 0x1000>;
+			interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 30>,
+			       <&edma0 1 31>;
+			status = "disabled";
+		};
+
+		lpuart2: serial@2280000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2280000 0x0 0x1000>;
+			interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 28>,
+			       <&edma0 1 29>;
+			status = "disabled";
+		};
+
+		lpuart3: serial@2290000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2290000 0x0 0x1000>;
+			interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 26>,
+			       <&edma0 1 27>;
+			status = "disabled";
+		};
+
+		lpuart4: serial@22a0000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x22a0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 24>,
+			       <&edma0 1 25>;
+			status = "disabled";
+		};
+
+		lpuart5: serial@22b0000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x22b0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 22>,
+			       <&edma0 1 23>;
+			status = "disabled";
+		};
+
 		edma0: dma-controller@22c0000 {
 			#dma-cells = <2>;
 			compatible = "fsl,ls1028a-edma";