Commit 28baebae authored by David Howells's avatar David Howells Committed by Linus Torvalds

[PATCH] FRV: Use virtual interrupt disablement

Make the FRV arch use virtual interrupt disablement because accesses to the
processor status register (PSR) are relatively slow and because we will
soon have the need to deal with multiple interrupt controls at the same
time (separate h/w and inter-core interrupts).

The way this is done is to dedicate one of the four integer condition code
registers (ICC2) to maintaining a virtual interrupt disablement state
whilst inside the kernel.  This uses the ICC2.Z flag (Zero) to indicate
whether the interrupts are virtually disabled and the ICC2.C flag (Carry)
to indicate whether the interrupts are physically disabled.

ICC2.Z is set to indicate interrupts are virtually disabled.  ICC2.C is set
to indicate interrupts are physically enabled.  Under normal running
conditions Z==0 and C==1.

Disabling interrupts with local_irq_disable() doesn't then actually
physically disable interrupts - it merely sets ICC2.Z to 1.  Should an
interrupt then happen, the exception prologue will note ICC2.Z is set and
branch out of line using one instruction (an unlikely BEQ).  Here it will
physically disable interrupts and clear ICC2.C.

When it comes time to enable interrupts (local_irq_enable()), this simply
clears the ICC2.Z flag and invokes a trap #2 if both Z and C flags are
clear (the HI integer condition).  This can be done with the TIHI
conditional trap instruction.

The trap then physically reenables interrupts and sets ICC2.C again.  Upon
returning the interrupt will be taken as interrupts will then be enabled.
Note that whilst processing the trap, the whole exceptions system is
disabled, and so an interrupt can't happen till it returns.

If no pending interrupt had happened, ICC2.C would still be set, the HI
condition would not be fulfilled, and no trap will happen.

Saving interrupts (local_irq_save) is simply a matter of pulling the ICC2.Z
flag out of the CCR register, shifting it down and masking it off.  This
gives a result of 0 if interrupts were enabled and 1 if they weren't.

Restoring interrupts (local_irq_restore) is then a matter of taking the
saved value mentioned previously and XOR'ing it against 1.  If it was one,
the result will be zero, and if it was zero the result will be non-zero.
This result is then used to affect the ICC2.Z flag directly (it is a
condition code flag after all).  An XOR instruction does not affect the
Carry flag, and so that bit of state is unchanged.  The two flags can then
be sampled to see if they're both zero using the trap (TIHI) as for the
unconditional reenablement (local_irq_enable).

This patch also:

 (1) Modifies the debugging stub (break.S) to handle single-stepping crossing
     into the trap #2 handler and into virtually disabled interrupts.

 (2) Removes superseded fixup pointers from the second instructions in the trap
     tables (there's no a separate fixup table for this).

 (3) Declares the trap #3 vector for use in .org directives in the trap table.

 (4) Moves irq_enter() and irq_exit() in do_IRQ() to avoid problems with
     virtual interrupt handling, and removes the duplicate code that has now
     been folded into irq_exit() (softirq and preemption handling).

 (5) Tells the compiler in the arch Makefile that ICC2 is now reserved.

 (6) Documents the in-kernel ABI, including the virtual interrupts.

 (7) Renames the old irq management functions to different names.
Signed-off-by: default avatarDavid Howells <dhowells@redhat.com>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent 68f624fc
=================================
INTERNAL KERNEL ABI FOR FR-V ARCH
=================================
The internal FRV kernel ABI is not quite the same as the userspace ABI. A number of the registers
are used for special purposed, and the ABI is not consistent between modules vs core, and MMU vs
no-MMU.
This partly stems from the fact that FRV CPUs do not have a separate supervisor stack pointer, and
most of them do not have any scratch registers, thus requiring at least one general purpose
register to be clobbered in such an event. Also, within the kernel core, it is possible to simply
jump or call directly between functions using a relative offset. This cannot be extended to modules
for the displacement is likely to be too far. Thus in modules the address of a function to call
must be calculated in a register and then used, requiring two extra instructions.
This document has the following sections:
(*) System call register ABI
(*) CPU operating modes
(*) Internal kernel-mode register ABI
(*) Internal debug-mode register ABI
(*) Virtual interrupt handling
========================
SYSTEM CALL REGISTER ABI
========================
When a system call is made, the following registers are effective:
REGISTERS CALL RETURN
=============== ======================= =======================
GR7 System call number Preserved
GR8 Syscall arg #1 Return value
GR9-GR13 Syscall arg #2-6 Preserved
===================
CPU OPERATING MODES
===================
The FR-V CPU has three basic operating modes. In order of increasing capability:
(1) User mode.
Basic userspace running mode.
(2) Kernel mode.
Normal kernel mode. There are many additional control registers available that may be
accessed in this mode, in addition to all the stuff available to user mode. This has two
submodes:
(a) Exceptions enabled (PSR.T == 1).
Exceptions will invoke the appropriate normal kernel mode handler. On entry to the
handler, the PSR.T bit will be cleared.
(b) Exceptions disabled (PSR.T == 0).
No exceptions or interrupts may happen. Any mandatory exceptions will cause the CPU to
halt unless the CPU is told to jump into debug mode instead.
(3) Debug mode.
No exceptions may happen in this mode. Memory protection and management exceptions will be
flagged for later consideration, but the exception handler won't be invoked. Debugging traps
such as hardware breakpoints and watchpoints will be ignored. This mode is entered only by
debugging events obtained from the other two modes.
All kernel mode registers may be accessed, plus a few extra debugging specific registers.
=================================
INTERNAL KERNEL-MODE REGISTER ABI
=================================
There are a number of permanent register assignments that are set up by entry.S in the exception
prologue. Note that there is a complete set of exception prologues for each of user->kernel
transition and kernel->kernel transition. There are also user->debug and kernel->debug mode
transition prologues.
REGISTER FLAVOUR USE
=============== ======= ====================================================
GR1 Supervisor stack pointer
GR15 Current thread info pointer
GR16 GP-Rel base register for small data
GR28 Current exception frame pointer (__frame)
GR29 Current task pointer (current)
GR30 Destroyed by kernel mode entry
GR31 NOMMU Destroyed by debug mode entry
GR31 MMU Destroyed by TLB miss kernel mode entry
CCR.ICC2 Virtual interrupt disablement tracking
CCCR.CC3 Cleared by exception prologue (atomic op emulation)
SCR0 MMU See mmu-layout.txt.
SCR1 MMU See mmu-layout.txt.
SCR2 MMU Save for EAR0 (destroyed by icache insns in debug mode)
SCR3 MMU Save for GR31 during debug exceptions
DAMR/IAMR NOMMU Fixed memory protection layout.
DAMR/IAMR MMU See mmu-layout.txt.
Certain registers are also used or modified across function calls:
REGISTER CALL RETURN
=============== =============================== ===============================
GR0 Fixed Zero -
GR2 Function call frame pointer
GR3 Special Preserved
GR3-GR7 - Clobbered
GR8 Function call arg #1 Return value (or clobbered)
GR9 Function call arg #2 Return value MSW (or clobbered)
GR10-GR13 Function call arg #3-#6 Clobbered
GR14 - Clobbered
GR15-GR16 Special Preserved
GR17-GR27 - Preserved
GR28-GR31 Special Only accessed explicitly
LR Return address after CALL Clobbered
CCR/CCCR - Mostly Clobbered
================================
INTERNAL DEBUG-MODE REGISTER ABI
================================
This is the same as the kernel-mode register ABI for functions calls. The difference is that in
debug-mode there's a different stack and a different exception frame. Almost all the global
registers from kernel-mode (including the stack pointer) may be changed.
REGISTER FLAVOUR USE
=============== ======= ====================================================
GR1 Debug stack pointer
GR16 GP-Rel base register for small data
GR31 Current debug exception frame pointer (__debug_frame)
SCR3 MMU Saved value of GR31
Note that debug mode is able to interfere with the kernel's emulated atomic ops, so it must be
exceedingly careful not to do any that would interact with the main kernel in this regard. Hence
the debug mode code (gdbstub) is almost completely self-contained. The only external code used is
the sprintf family of functions.
Futhermore, break.S is so complicated because single-step mode does not switch off on entry to an
exception. That means unless manually disabled, single-stepping will blithely go on stepping into
things like interrupts. See gdbstub.txt for more information.
==========================
VIRTUAL INTERRUPT HANDLING
==========================
Because accesses to the PSR is so slow, and to disable interrupts we have to access it twice (once
to read and once to write), we don't actually disable interrupts at all if we don't have to. What
we do instead is use the ICC2 condition code flags to note virtual disablement, such that if we
then do take an interrupt, we note the flag, really disable interrupts, set another flag and resume
execution at the point the interrupt happened. Setting condition flags as a side effect of an
arithmetic or logical instruction is really fast. This use of the ICC2 only occurs within the
kernel - it does not affect userspace.
The flags we use are:
(*) CCR.ICC2.Z [Zero flag]
Set to virtually disable interrupts, clear when interrupts are virtually enabled. Can be
modified by logical instructions without affecting the Carry flag.
(*) CCR.ICC2.C [Carry flag]
Clear to indicate hardware interrupts are really disabled, set otherwise.
What happens is this:
(1) Normal kernel-mode operation.
ICC2.Z is 0, ICC2.C is 1.
(2) An interrupt occurs. The exception prologue examines ICC2.Z and determines that nothing needs
doing. This is done simply with an unlikely BEQ instruction.
(3) The interrupts are disabled (local_irq_disable)
ICC2.Z is set to 1.
(4) If interrupts were then re-enabled (local_irq_enable):
ICC2.Z would be set to 0.
A TIHI #2 instruction (trap #2 if condition HI - Z==0 && C==0) would be used to trap if
interrupts were now virtually enabled, but physically disabled - which they're not, so the
trap isn't taken. The kernel would then be back to state (1).
(5) An interrupt occurs. The exception prologue examines ICC2.Z and determines that the interrupt
shouldn't actually have happened. It jumps aside, and there disabled interrupts by setting
PSR.PIL to 14 and then it clears ICC2.C.
(6) If interrupts were then saved and disabled again (local_irq_save):
ICC2.Z would be shifted into the save variable and masked off (giving a 1).
ICC2.Z would then be set to 1 (thus unchanged), and ICC2.C would be unaffected (ie: 0).
(7) If interrupts were then restored from state (6) (local_irq_restore):
ICC2.Z would be set to indicate the result of XOR'ing the saved value (ie: 1) with 1, which
gives a result of 0 - thus leaving ICC2.Z set.
ICC2.C would remain unaffected (ie: 0).
A TIHI #2 instruction would be used to again assay the current state, but this would do
nothing as Z==1.
(8) If interrupts were then enabled (local_irq_enable):
ICC2.Z would be cleared. ICC2.C would be left unaffected. Both flags would now be 0.
A TIHI #2 instruction again issued to assay the current state would then trap as both Z==0
[interrupts virtually enabled] and C==0 [interrupts really disabled] would then be true.
(9) The trap #2 handler would simply enable hardware interrupts (set PSR.PIL to 0), set ICC2.C to
1 and return.
(10) Immediately upon returning, the pending interrupt would be taken.
(11) The interrupt handler would take the path of actually processing the interrupt (ICC2.Z is
clear, BEQ fails as per step (2)).
(12) The interrupt handler would then set ICC2.C to 1 since hardware interrupts are definitely
enabled - or else the kernel wouldn't be here.
(13) On return from the interrupt handler, things would be back to state (1).
This trap (#2) is only available in kernel mode. In user mode it will result in SIGILL.
......@@ -81,7 +81,7 @@ endif
# - reserve CC3 for use with atomic ops
# - all the extra registers are dealt with only at context switch time
CFLAGS += -mno-fdpic -mgpr-32 -msoft-float -mno-media
CFLAGS += -ffixed-fcc3 -ffixed-cc3 -ffixed-gr15
CFLAGS += -ffixed-fcc3 -ffixed-cc3 -ffixed-gr15 -ffixed-icc2
AFLAGS += -mno-fdpic
ASFLAGS += -mno-fdpic
......
......@@ -200,12 +200,20 @@ __break_step:
movsg bpcsr,gr2
sethi.p %hi(__entry_kernel_external_interrupt),gr3
setlo %lo(__entry_kernel_external_interrupt),gr3
subcc gr2,gr3,gr0,icc0
subcc.p gr2,gr3,gr0,icc0
sethi %hi(__entry_uspace_external_interrupt),gr3
setlo.p %lo(__entry_uspace_external_interrupt),gr3
beq icc0,#2,__break_step_kernel_external_interrupt
sethi.p %hi(__entry_uspace_external_interrupt),gr3
setlo %lo(__entry_uspace_external_interrupt),gr3
subcc gr2,gr3,gr0,icc0
subcc.p gr2,gr3,gr0,icc0
sethi %hi(__entry_kernel_external_interrupt_virtually_disabled),gr3
setlo.p %lo(__entry_kernel_external_interrupt_virtually_disabled),gr3
beq icc0,#2,__break_step_uspace_external_interrupt
subcc.p gr2,gr3,gr0,icc0
sethi %hi(__entry_kernel_external_interrupt_virtual_reenable),gr3
setlo.p %lo(__entry_kernel_external_interrupt_virtual_reenable),gr3
beq icc0,#2,__break_step_kernel_external_interrupt_virtually_disabled
subcc gr2,gr3,gr0,icc0
beq icc0,#2,__break_step_kernel_external_interrupt_virtual_reenable
LEDS 0x2007,gr2
......@@ -254,6 +262,9 @@ __break_step_kernel_softprog_interrupt:
# step through an external interrupt from kernel mode
.globl __break_step_kernel_external_interrupt
__break_step_kernel_external_interrupt:
# deal with virtual interrupt disablement
beq icc2,#0,__break_step_kernel_external_interrupt_virtually_disabled
sethi.p %hi(__entry_kernel_external_interrupt_reentry),gr3
setlo %lo(__entry_kernel_external_interrupt_reentry),gr3
......@@ -294,6 +305,64 @@ __break_return_as_kernel_prologue:
#endif
rett #1
# we single-stepped into an interrupt handler whilst interrupts were merely virtually disabled
# need to really disable interrupts, set flag, fix up and return
__break_step_kernel_external_interrupt_virtually_disabled:
movsg psr,gr2
andi gr2,#~PSR_PIL,gr2
ori gr2,#PSR_PIL_14,gr2 /* debugging interrupts only */
movgs gr2,psr
ldi @(gr31,#REG_CCR),gr3
movgs gr3,ccr
subcc.p gr0,gr0,gr0,icc2 /* leave Z set, clear C */
# exceptions must've been enabled and we must've been in supervisor mode
setlos BPSR_BET|BPSR_BS,gr3
movgs gr3,bpsr
# return to where the interrupt happened
movsg pcsr,gr2
movgs gr2,bpcsr
lddi.p @(gr31,#REG_GR(2)),gr2
xor gr31,gr31,gr31
movgs gr0,brr
#ifdef CONFIG_MMU
movsg scr3,gr31
#endif
rett #1
# we stepped through into the virtual interrupt reenablement trap
#
# we also want to single step anyway, but after fixing up so that we get an event on the
# instruction after the broken-into exception returns
.globl __break_step_kernel_external_interrupt_virtual_reenable
__break_step_kernel_external_interrupt_virtual_reenable:
movsg psr,gr2
andi gr2,#~PSR_PIL,gr2
movgs gr2,psr
ldi @(gr31,#REG_CCR),gr3
movgs gr3,ccr
subicc gr0,#1,gr0,icc2 /* clear Z, set C */
# save the adjusted ICC2
movsg ccr,gr3
sti gr3,@(gr31,#REG_CCR)
# exceptions must've been enabled and we must've been in supervisor mode
setlos BPSR_BET|BPSR_BS,gr3
movgs gr3,bpsr
# return to where the trap happened
movsg pcsr,gr2
movgs gr2,bpcsr
# and then process the single step
bra __break_continue
# step through an internal exception from uspace mode
.globl __break_step_uspace_softprog_interrupt
__break_step_uspace_softprog_interrupt:
......
......@@ -116,6 +116,8 @@ __break_kerneltrap_fixup_table:
.long __break_step_uspace_external_interrupt
.section .trap.kernel
.org \tbr_tt
# deal with virtual interrupt disablement
beq icc2,#0,__entry_kernel_external_interrupt_virtually_disabled
bra __entry_kernel_external_interrupt
.section .trap.fixup.kernel
.org \tbr_tt >> 2
......@@ -259,25 +261,52 @@ __trap_fixup_kernel_data_tlb_miss:
.org TBR_TT_TRAP0
.rept 127
bra __entry_uspace_softprog_interrupt
bra __break_step_uspace_softprog_interrupt
.long 0,0
.long 0,0,0
.endr
.org TBR_TT_BREAK
bra __entry_break
.long 0,0,0
.section .trap.fixup.user
.org TBR_TT_TRAP0 >> 2
.rept 127
.long __break_step_uspace_softprog_interrupt
.endr
.org TBR_TT_BREAK >> 2
.long 0
# miscellaneous kernel mode entry points
.section .trap.kernel
.org TBR_TT_TRAP0
.rept 127
bra __entry_kernel_softprog_interrupt
bra __break_step_kernel_softprog_interrupt
.long 0,0
.org TBR_TT_TRAP1
bra __entry_kernel_softprog_interrupt
# trap #2 in kernel - reenable interrupts
.org TBR_TT_TRAP2
bra __entry_kernel_external_interrupt_virtual_reenable
# miscellaneous kernel traps
.org TBR_TT_TRAP3
.rept 124
bra __entry_kernel_softprog_interrupt
.long 0,0,0
.endr
.org TBR_TT_BREAK
bra __entry_break
.long 0,0,0
.section .trap.fixup.kernel
.org TBR_TT_TRAP0 >> 2
.long __break_step_kernel_softprog_interrupt
.long __break_step_kernel_softprog_interrupt
.long __break_step_kernel_external_interrupt_virtual_reenable
.rept 124
.long __break_step_kernel_softprog_interrupt
.endr
.org TBR_TT_BREAK >> 2
.long 0
# miscellaneous debug mode entry points
.section .trap.break
.org TBR_TT_BREAK
......
......@@ -141,7 +141,10 @@ __entry_uspace_external_interrupt_reentry:
movsg gner0,gr4
movsg gner1,gr5
stdi gr4,@(gr28,#REG_GNER0)
stdi.p gr4,@(gr28,#REG_GNER0)
# interrupts start off fully disabled in the interrupt handler
subcc gr0,gr0,gr0,icc2 /* set Z and clear C */
# set up kernel global registers
sethi.p %hi(__kernel_current_task),gr5
......@@ -193,9 +196,8 @@ __entry_uspace_external_interrupt_reentry:
.type __entry_kernel_external_interrupt,@function
__entry_kernel_external_interrupt:
LEDS 0x6210
sub sp,gr15,gr31
LEDS32
// sub sp,gr15,gr31
// LEDS32
# set up the stack pointer
or.p sp,gr0,gr30
......@@ -231,7 +233,10 @@ __entry_kernel_external_interrupt_reentry:
stdi gr24,@(gr28,#REG_GR(24))
stdi gr26,@(gr28,#REG_GR(26))
sti gr29,@(gr28,#REG_GR(29))
stdi gr30,@(gr28,#REG_GR(30))
stdi.p gr30,@(gr28,#REG_GR(30))
# note virtual interrupts will be fully enabled upon return
subicc gr0,#1,gr0,icc2 /* clear Z, set C */
movsg tbr ,gr20
movsg psr ,gr22
......@@ -267,7 +272,10 @@ __entry_kernel_external_interrupt_reentry:
movsg gner0,gr4
movsg gner1,gr5
stdi gr4,@(gr28,#REG_GNER0)
stdi.p gr4,@(gr28,#REG_GNER0)
# interrupts start off fully disabled in the interrupt handler
subcc gr0,gr0,gr0,icc2 /* set Z and clear C */
# set the return address
sethi.p %hi(__entry_return_from_kernel_interrupt),gr4
......@@ -291,6 +299,45 @@ __entry_kernel_external_interrupt_reentry:
.size __entry_kernel_external_interrupt,.-__entry_kernel_external_interrupt
###############################################################################
#
# deal with interrupts that were actually virtually disabled
# - we need to really disable them, flag the fact and return immediately
# - if you change this, you must alter break.S also
#
###############################################################################
.balign L1_CACHE_BYTES
.globl __entry_kernel_external_interrupt_virtually_disabled
.type __entry_kernel_external_interrupt_virtually_disabled,@function
__entry_kernel_external_interrupt_virtually_disabled:
movsg psr,gr30
andi gr30,#~PSR_PIL,gr30
ori gr30,#PSR_PIL_14,gr30 ; debugging interrupts only
movgs gr30,psr
subcc gr0,gr0,gr0,icc2 ; leave Z set, clear C
rett #0
.size __entry_kernel_external_interrupt_virtually_disabled,.-__entry_kernel_external_interrupt_virtually_disabled
###############################################################################
#
# deal with re-enablement of interrupts that were pending when virtually re-enabled
# - set ICC2.C, re-enable the real interrupts and return
# - we can clear ICC2.Z because we shouldn't be here if it's not 0 [due to TIHI]
# - if you change this, you must alter break.S also
#
###############################################################################
.balign L1_CACHE_BYTES
.globl __entry_kernel_external_interrupt_virtual_reenable
.type __entry_kernel_external_interrupt_virtual_reenable,@function
__entry_kernel_external_interrupt_virtual_reenable:
movsg psr,gr30
andi gr30,#~PSR_PIL,gr30 ; re-enable interrupts
movgs gr30,psr
subicc gr0,#1,gr0,icc2 ; clear Z, set C
rett #0
.size __entry_kernel_external_interrupt_virtual_reenable,.-__entry_kernel_external_interrupt_virtual_reenable
###############################################################################
#
......@@ -335,6 +382,7 @@ __entry_uspace_softprog_interrupt_reentry:
sethi.p %hi(__entry_return_from_user_exception),gr23
setlo %lo(__entry_return_from_user_exception),gr23
bra __entry_common
.size __entry_uspace_softprog_interrupt,.-__entry_uspace_softprog_interrupt
......@@ -495,7 +543,10 @@ __entry_common:
movsg gner0,gr4
movsg gner1,gr5
stdi gr4,@(gr28,#REG_GNER0)
stdi.p gr4,@(gr28,#REG_GNER0)
# set up virtual interrupt disablement
subicc gr0,#1,gr0,icc2 /* clear Z flag, set C flag */
# set up kernel global registers
sethi.p %hi(__kernel_current_task),gr5
......
......@@ -513,6 +513,9 @@ __head_mmu_enabled:
movgs gr0,ccr
movgs gr0,cccr
# initialise the virtual interrupt handling
subcc gr0,gr0,gr0,icc2 /* set Z, clear C */
#ifdef CONFIG_MMU
movgs gr3,scr2
movgs gr3,scr3
......
......@@ -287,18 +287,11 @@ asmlinkage void do_IRQ(void)
struct irq_source *source;
int level, cpu;
irq_enter();
level = (__frame->tbr >> 4) & 0xf;
cpu = smp_processor_id();
#if 0
{
static u32 irqcount;
*(volatile u32 *) 0xe1200004 = ~((irqcount++ << 8) | level);
*(volatile u16 *) 0xffc00100 = (u16) ~0x9999;
mb();
}
#endif
if ((unsigned long) __frame - (unsigned long) (current + 1) < 512)
BUG();
......@@ -308,40 +301,12 @@ asmlinkage void do_IRQ(void)
kstat_this_cpu.irqs[level]++;
irq_enter();
for (source = frv_irq_levels[level].sources; source; source = source->next)
source->doirq(source);
irq_exit();
__clr_MASK(level);
/* only process softirqs if we didn't interrupt another interrupt handler */
if ((__frame->psr & PSR_PIL) == PSR_PIL_0)
if (local_softirq_pending())
do_softirq();
#ifdef CONFIG_PREEMPT
local_irq_disable();
while (--current->preempt_count == 0) {
if (!(__frame->psr & PSR_S) ||
current->need_resched == 0 ||
in_interrupt())
break;
current->preempt_count++;
local_irq_enable();
preempt_schedule();
local_irq_disable();
}
#endif
#if 0
{
*(volatile u16 *) 0xffc00100 = (u16) ~0x6666;
mb();
}
#endif
irq_exit();
} /* end do_IRQ() */
......
......@@ -98,6 +98,7 @@
#define TBR_TT_TRAP0 (0x80 << 4)
#define TBR_TT_TRAP1 (0x81 << 4)
#define TBR_TT_TRAP2 (0x82 << 4)
#define TBR_TT_TRAP3 (0x83 << 4)
#define TBR_TT_TRAP126 (0xfe << 4)
#define TBR_TT_BREAK (0xff << 4)
......
......@@ -40,8 +40,84 @@ do { \
/*
* interrupt flag manipulation
* - use virtual interrupt management since touching the PSR is slow
* - ICC2.Z: T if interrupts virtually disabled
* - ICC2.C: F if interrupts really disabled
* - if Z==1 upon interrupt:
* - C is set to 0
* - interrupts are really disabled
* - entry.S returns immediately
* - uses TIHI (TRAP if Z==0 && C==0) #2 to really reenable interrupts
* - if taken, the trap:
* - sets ICC2.C
* - enables interrupts
*/
#define local_irq_disable() \
#define local_irq_disable() \
do { \
/* set Z flag, but don't change the C flag */ \
asm volatile(" andcc gr0,gr0,gr0,icc2 \n" \
: \
: \
: "memory", "icc2" \
); \
} while(0)
#define local_irq_enable() \
do { \
/* clear Z flag and then test the C flag */ \
asm volatile(" oricc gr0,#1,gr0,icc2 \n" \
" tihi icc2,gr0,#2 \n" \
: \
: \
: "memory", "icc2" \
); \
} while(0)
#define local_save_flags(flags) \
do { \
typecheck(unsigned long, flags); \
asm volatile("movsg ccr,%0" \
: "=r"(flags) \
: \
: "memory"); \
\
/* shift ICC2.Z to bit 0 */ \
flags >>= 26; \
\
/* make flags 1 if interrupts disabled, 0 otherwise */ \
flags &= 1UL; \
} while(0)
#define irqs_disabled() \
({unsigned long flags; local_save_flags(flags); flags; })
#define local_irq_save(flags) \
do { \
typecheck(unsigned long, flags); \
local_save_flags(flags); \
local_irq_disable(); \
} while(0)
#define local_irq_restore(flags) \
do { \
typecheck(unsigned long, flags); \
\
/* load the Z flag by turning 1 if disabled into 0 if disabled \
* and thus setting the Z flag but not the C flag */ \
asm volatile(" xoricc %0,#1,gr0,icc2 \n" \
/* then test Z=0 and C=0 */ \
" tihi icc2,gr0,#2 \n" \
: \
: "r"(flags) \
: "memory", "icc2" \
); \
\
} while(0)
/*
* real interrupt flag manipulation
*/
#define __local_irq_disable() \
do { \
unsigned long psr; \
asm volatile(" movsg psr,%0 \n" \
......@@ -53,7 +129,7 @@ do { \
: "memory"); \
} while(0)
#define local_irq_enable() \
#define __local_irq_enable() \
do { \
unsigned long psr; \
asm volatile(" movsg psr,%0 \n" \
......@@ -64,7 +140,7 @@ do { \
: "memory"); \
} while(0)
#define local_save_flags(flags) \
#define __local_save_flags(flags) \
do { \
typecheck(unsigned long, flags); \
asm("movsg psr,%0" \
......@@ -73,7 +149,7 @@ do { \
: "memory"); \
} while(0)
#define local_irq_save(flags) \
#define __local_irq_save(flags) \
do { \
unsigned long npsr; \
typecheck(unsigned long, flags); \
......@@ -86,7 +162,7 @@ do { \
: "memory"); \
} while(0)
#define local_irq_restore(flags) \
#define __local_irq_restore(flags) \
do { \
typecheck(unsigned long, flags); \
asm volatile(" movgs %0,psr \n" \
......@@ -95,7 +171,7 @@ do { \
: "memory"); \
} while(0)
#define irqs_disabled() \
#define __irqs_disabled() \
((__get_PSR() & PSR_PIL) >= PSR_PIL_14)
/*
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment