Merge git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: Make atstk1006_nand_data definition static
  avr32: Reduce DataFlash bus speed to 8 MHz on ATNGW100
  avr32: Update defconfigs
  avr32: Clean up HMATRIX code
  avr32: Add MMIO address definitions for certain controllers
  avr32: Introduce <mach/chip.h>
  avr32: Remove include/asm-avr32/arch-at32ap

arch/avr32/Makefile

@@ -39,20 +39,6 @@ core-y					+= arch/avr32/mm/
 drivers-$(CONFIG_OPROFILE)		+= arch/avr32/oprofile/
 libs-y					+= arch/avr32/lib/
 
-archincdir-$(CONFIG_PLATFORM_AT32AP)	:= arch-at32ap
-
-include/asm-avr32/.arch: $(wildcard include/config/platform/*.h) include/config/auto.conf
-	@echo '  SYMLINK include/asm-avr32/arch -> include/asm-avr32/$(archincdir-y)'
-ifneq ($(KBUILD_SRC),)
-	$(Q)mkdir -p include/asm-avr32
-	$(Q)ln -fsn $(srctree)/include/asm-avr32/$(archincdir-y) include/asm-avr32/arch
-else
-	$(Q)ln -fsn $(archincdir-y) include/asm-avr32/arch
-endif
-	@touch $@
-
-archprepare: include/asm-avr32/.arch
-
 CLEAN_FILES += include/asm-avr32/.arch include/asm-avr32/arch
 
 BOOT_TARGETS := vmlinux.elf vmlinux.bin uImage uImage.srec

arch/avr32/boards/atngw100/setup.c

@@ -47,7 +47,7 @@ static struct eth_platform_data __initdata eth_data[2];
 static struct spi_board_info spi0_board_info[] __initdata = {
 	{
 		.modalias	= "mtd_dataflash",
-		.max_speed_hz	= 10000000,
+		.max_speed_hz	= 8000000,
 		.chip_select	= 0,
 	},
 };

arch/avr32/boards/atstk1000/atstk1002.c

@@ -96,7 +96,7 @@ static struct mtd_partition *nand_part_info(int size, int *num_partitions)
 	return nand_partitions;
 }
 
-struct atmel_nand_data atstk1006_nand_data __initdata = {
+static struct atmel_nand_data atstk1006_nand_data __initdata = {
 	.cle		= 21,
 	.ale		= 22,
 	.rdy_pin	= GPIO_PIN_PB(30),

arch/avr32/configs/atngw100_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc3
-# Mon May 26 13:30:59 2008
+# Linux kernel version: 2.6.27-rc1
+# Tue Aug  5 16:00:47 2008
 #
 CONFIG_AVR32=y
 CONFIG_GENERIC_GPIO=y
@@ -78,10 +78,16 @@ CONFIG_PROFILING=y
 CONFIG_OPROFILE=m
 CONFIG_HAVE_OPROFILE=y
 CONFIG_KPROBES=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
 CONFIG_HAVE_KPROBES=y
 # CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
 # CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
 CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_RT_MUTEXES=y
 # CONFIG_TINY_SHMEM is not set
@@ -98,6 +104,7 @@ CONFIG_BLOCK=y
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_LSF is not set
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
 # IO Schedulers
@@ -142,6 +149,7 @@ CONFIG_PHYS_OFFSET=0x10000000
 CONFIG_PREEMPT_NONE=y
 # CONFIG_PREEMPT_VOLUNTARY is not set
 # CONFIG_PREEMPT is not set
+CONFIG_QUICKLIST=y
 # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set
 # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set
 # CONFIG_NEED_NODE_MEMMAP_SIZE is not set
@@ -160,6 +168,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_RESOURCES_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
 CONFIG_VIRT_TO_BUS=y
 # CONFIG_OWNERSHIP_TRACE is not set
 CONFIG_NMI_DEBUGGING=y
@@ -174,6 +183,12 @@ CONFIG_CMDLINE=""
 #
 # Power management options
 #
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
 
 #
 # CPU Frequency scaling
@@ -205,10 +220,6 @@ CONFIG_CPU_FREQ_AT32AP=y
 #
 CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
-
-#
-# Networking
-#
 CONFIG_NET=y
 
 #
@@ -222,6 +233,7 @@ CONFIG_XFRM_USER=y
 # CONFIG_XFRM_SUB_POLICY is not set
 # CONFIG_XFRM_MIGRATE is not set
 # CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=y
 CONFIG_NET_KEY=y
 # CONFIG_NET_KEY_MIGRATE is not set
 CONFIG_INET=y
@@ -339,8 +351,10 @@ CONFIG_IP6_NF_MANGLE=m
 # CONFIG_IP_SCTP is not set
 # CONFIG_TIPC is not set
 # CONFIG_ATM is not set
+CONFIG_STP=m
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
+# CONFIG_VLAN_8021Q_GVRP is not set
 # CONFIG_DECNET is not set
 CONFIG_LLC=m
 # CONFIG_LLC2 is not set
@@ -499,7 +513,6 @@ CONFIG_ATMEL_TCB_CLKSRC_BLOCK=0
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -607,21 +620,35 @@ CONFIG_I2C_ALGOBIT=m
 #
 # I2C Hardware Bus support
 #
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
 CONFIG_I2C_GPIO=m
 # CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
 # CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
 
 #
 # Miscellaneous I2C Chip support
 #
 # CONFIG_DS1682 is not set
+CONFIG_AT24=m
 # CONFIG_SENSORS_EEPROM is not set
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
 # CONFIG_SENSORS_PCF8591 is not set
 # CONFIG_TPS65010 is not set
 # CONFIG_SENSORS_MAX6875 is not set
@@ -646,27 +673,32 @@ CONFIG_SPI_ATMEL=y
 # CONFIG_SPI_AT25 is not set
 CONFIG_SPI_SPIDEV=m
 # CONFIG_SPI_TLE62X0 is not set
-CONFIG_HAVE_GPIO_LIB=y
-
-#
-# GPIO Support
-#
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
 # CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
 
 #
 # I2C GPIO expanders:
 #
+# CONFIG_GPIO_MAX732X is not set
 # CONFIG_GPIO_PCA953X is not set
 # CONFIG_GPIO_PCF857X is not set
 
+#
+# PCI GPIO expanders:
+#
+
 #
 # SPI GPIO expanders:
 #
+# CONFIG_GPIO_MAX7301 is not set
 # CONFIG_GPIO_MCP23S08 is not set
 # CONFIG_W1 is not set
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
 # CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
 CONFIG_WATCHDOG=y
 # CONFIG_WATCHDOG_NOWAYOUT is not set
 
@@ -685,6 +717,7 @@ CONFIG_SSB_POSSIBLE=y
 #
 # Multifunction device drivers
 #
+# CONFIG_MFD_CORE is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
 
@@ -716,10 +749,6 @@ CONFIG_SSB_POSSIBLE=y
 # Display device support
 #
 # CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
 # CONFIG_SOUND is not set
 CONFIG_USB_SUPPORT=y
 # CONFIG_USB_ARCH_HAS_HCD is not set
@@ -740,7 +769,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y
 CONFIG_USB_ATMEL_USBA=y
 # CONFIG_USB_GADGET_FSL_USB2 is not set
 # CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_PXA25X is not set
 # CONFIG_USB_GADGET_M66592 is not set
 # CONFIG_USB_GADGET_PXA27X is not set
 # CONFIG_USB_GADGET_GOKU is not set
@@ -759,21 +788,24 @@ CONFIG_USB_FILE_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 # CONFIG_USB_MIDI_GADGET is not set
 # CONFIG_USB_G_PRINTER is not set
-CONFIG_MMC=m
+CONFIG_USB_CDC_COMPOSITE=m
+CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set
 # CONFIG_MMC_UNSAFE_RESUME is not set
 
 #
 # MMC/SD Card Drivers
 #
-CONFIG_MMC_BLOCK=m
+CONFIG_MMC_BLOCK=y
 CONFIG_MMC_BLOCK_BOUNCE=y
 # CONFIG_SDIO_UART is not set
-# CONFIG_MMC_TEST is not set
+CONFIG_MMC_TEST=m
 
 #
 # MMC/SD Host Controller Drivers
 #
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_ATMELMCI=y
 CONFIG_MMC_SPI=m
 # CONFIG_MEMSTICK is not set
 CONFIG_NEW_LEDS=y
@@ -783,6 +815,7 @@ CONFIG_LEDS_CLASS=y
 # LED drivers
 #
 CONFIG_LEDS_GPIO=y
+# CONFIG_LEDS_PCA955X is not set
 
 #
 # LED Triggers
@@ -821,10 +854,13 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_PCF8583 is not set
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
 
 #
 # SPI RTC drivers
 #
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
 # CONFIG_RTC_DRV_MAX6902 is not set
 # CONFIG_RTC_DRV_R9701 is not set
 # CONFIG_RTC_DRV_RS5C348 is not set
@@ -844,6 +880,19 @@ CONFIG_RTC_INTF_DEV=y
 # on-CPU RTC drivers
 #
 CONFIG_RTC_DRV_AT32AP700X=y
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+CONFIG_DW_DMAC=y
+CONFIG_DMA_ENGINE=y
+
+#
+# DMA Clients
+#
+# CONFIG_NET_DMA is not set
+CONFIG_DMATEST=m
 # CONFIG_UIO is not set
 
 #
@@ -921,6 +970,7 @@ CONFIG_JFFS2_RTIME=y
 # CONFIG_CRAMFS is not set
 # CONFIG_VXFS_FS is not set
 # CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
 # CONFIG_HPFS_FS is not set
 # CONFIG_QNX4FS_FS is not set
 # CONFIG_ROMFS_FS is not set
@@ -931,17 +981,16 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 # CONFIG_NFS_V4 is not set
+CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
 CONFIG_NFSD_V3=y
 # CONFIG_NFSD_V3_ACL is not set
 # CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
 CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
 CONFIG_EXPORTFS=m
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
 # CONFIG_RPCSEC_GSS_KRB5 is not set
 # CONFIG_RPCSEC_GSS_SPKM3 is not set
 CONFIG_SMB_FS=m
@@ -1017,6 +1066,8 @@ CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_DEBUG_SHIRQ is not set
 CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
 CONFIG_SCHED_DEBUG=y
 # CONFIG_SCHEDSTATS is not set
 # CONFIG_TIMER_STATS is not set
@@ -1037,6 +1088,7 @@ CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_DEBUG_VM is not set
 # CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 CONFIG_FRAME_POINTER=y
@@ -1101,6 +1153,10 @@ CONFIG_CRYPTO_HMAC=y
 # CONFIG_CRYPTO_MD4 is not set
 CONFIG_CRYPTO_MD5=y
 # CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
 CONFIG_CRYPTO_SHA1=y
 # CONFIG_CRYPTO_SHA256 is not set
 # CONFIG_CRYPTO_SHA512 is not set
@@ -1141,12 +1197,14 @@ CONFIG_BITREVERSE=y
 # CONFIG_GENERIC_FIND_NEXT_BIT is not set
 CONFIG_CRC_CCITT=m
 # CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
 CONFIG_CRC_ITU_T=m
 CONFIG_CRC32=y
 CONFIG_CRC7=m
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_GENERIC_ALLOCATOR=y
 CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y

arch/avr32/configs/atstk1003_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc3
-# Mon May 26 13:33:05 2008
+# Linux kernel version: 2.6.27-rc1
+# Tue Aug  5 15:34:44 2008
 #
 CONFIG_AVR32=y
 CONFIG_GENERIC_GPIO=y
@@ -80,10 +80,16 @@ CONFIG_PROFILING=y
 CONFIG_OPROFILE=m
 CONFIG_HAVE_OPROFILE=y
 CONFIG_KPROBES=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
 CONFIG_HAVE_KPROBES=y
 # CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
 # CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
 CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_RT_MUTEXES=y
 # CONFIG_TINY_SHMEM is not set
 CONFIG_BASE_SMALL=1
@@ -93,12 +99,13 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODULE_FORCE_UNLOAD is not set
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
 CONFIG_BLOCK=y
 # CONFIG_LBD is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_LSF is not set
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
 # IO Schedulers
@@ -132,6 +139,7 @@ CONFIG_BOARD_ATSTK1000=y
 # CONFIG_BOARD_ATSTK1002 is not set
 CONFIG_BOARD_ATSTK1003=y
 # CONFIG_BOARD_ATSTK1004 is not set
+# CONFIG_BOARD_ATSTK1006 is not set
 # CONFIG_BOARD_ATSTK100X_CUSTOM is not set
 # CONFIG_BOARD_ATSTK100X_SPI1 is not set
 # CONFIG_BOARD_ATSTK1000_J2_LED is not set
@@ -152,6 +160,7 @@ CONFIG_PHYS_OFFSET=0x10000000
 CONFIG_PREEMPT_NONE=y
 # CONFIG_PREEMPT_VOLUNTARY is not set
 # CONFIG_PREEMPT is not set
+CONFIG_QUICKLIST=y
 # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set
 # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set
 # CONFIG_NEED_NODE_MEMMAP_SIZE is not set
@@ -170,6 +179,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_RESOURCES_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
 CONFIG_VIRT_TO_BUS=y
 # CONFIG_OWNERSHIP_TRACE is not set
 CONFIG_NMI_DEBUGGING=y
@@ -184,6 +194,12 @@ CONFIG_CMDLINE=""
 #
 # Power management options
 #
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
 
 #
 # CPU Frequency scaling
@@ -215,10 +231,6 @@ CONFIG_CPU_FREQ_AT32AP=y
 #
 CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
-
-#
-# Networking
-#
 CONFIG_NET=y
 
 #
@@ -449,6 +461,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
 CONFIG_ATA=m
 # CONFIG_ATA_NONSTANDARD is not set
 # CONFIG_SATA_PMP is not set
@@ -458,7 +471,6 @@ CONFIG_PATA_AT32=m
 # CONFIG_PATA_PLATFORM is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -575,21 +587,35 @@ CONFIG_I2C_ALGOBIT=m
 #
 # I2C Hardware Bus support
 #
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
 CONFIG_I2C_GPIO=m
 # CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
 # CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
 # CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
 
 #
 # Miscellaneous I2C Chip support
 #
 # CONFIG_DS1682 is not set
+CONFIG_AT24=m
 # CONFIG_SENSORS_EEPROM is not set
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
 # CONFIG_SENSORS_PCF8591 is not set
 # CONFIG_TPS65010 is not set
 # CONFIG_SENSORS_MAX6875 is not set
@@ -614,27 +640,32 @@ CONFIG_SPI_ATMEL=y
 # CONFIG_SPI_AT25 is not set
 CONFIG_SPI_SPIDEV=m
 # CONFIG_SPI_TLE62X0 is not set
-CONFIG_HAVE_GPIO_LIB=y
-
-#
-# GPIO Support
-#
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
 # CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
 
 #
 # I2C GPIO expanders:
 #
+# CONFIG_GPIO_MAX732X is not set
 # CONFIG_GPIO_PCA953X is not set
 # CONFIG_GPIO_PCF857X is not set
 
+#
+# PCI GPIO expanders:
+#
+
 #
 # SPI GPIO expanders:
 #
+# CONFIG_GPIO_MAX7301 is not set
 # CONFIG_GPIO_MCP23S08 is not set
 # CONFIG_W1 is not set
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
 # CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
 CONFIG_WATCHDOG=y
 # CONFIG_WATCHDOG_NOWAYOUT is not set
 
@@ -653,6 +684,7 @@ CONFIG_SSB_POSSIBLE=y
 #
 # Multifunction device drivers
 #
+# CONFIG_MFD_CORE is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
 
@@ -684,15 +716,7 @@ CONFIG_SSB_POSSIBLE=y
 # Display device support
 #
 # CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
 CONFIG_SOUND=m
-
-#
-# Advanced Linux Sound Architecture
-#
 CONFIG_SND=m
 CONFIG_SND_TIMER=m
 CONFIG_SND_PCM=m
@@ -706,37 +730,11 @@ CONFIG_SND_SUPPORT_OLD_API=y
 CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
-
-#
-# Generic devices
-#
-# CONFIG_SND_DUMMY is not set
-# CONFIG_SND_MTPAV is not set
-# CONFIG_SND_SERIAL_U16550 is not set
-# CONFIG_SND_MPU401 is not set
-
-#
-# SPI devices
-#
+# CONFIG_SND_DRIVERS is not set
+CONFIG_SND_SPI=y
 CONFIG_SND_AT73C213=m
 CONFIG_SND_AT73C213_TARGET_BITRATE=48000
-
-#
-# System on Chip audio support
-#
 # CONFIG_SND_SOC is not set
-
-#
-# ALSA SoC audio for Freescale SOCs
-#
-
-#
-# SoC Audio for the Texas Instruments OMAP
-#
-
-#
-# Open Sound System
-#
 # CONFIG_SOUND_PRIME is not set
 # CONFIG_HID_SUPPORT is not set
 CONFIG_USB_SUPPORT=y
@@ -759,7 +757,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y
 CONFIG_USB_ATMEL_USBA=y
 # CONFIG_USB_GADGET_FSL_USB2 is not set
 # CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_PXA25X is not set
 # CONFIG_USB_GADGET_M66592 is not set
 # CONFIG_USB_GADGET_PXA27X is not set
 # CONFIG_USB_GADGET_GOKU is not set
@@ -778,21 +776,24 @@ CONFIG_USB_FILE_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 # CONFIG_USB_MIDI_GADGET is not set
 # CONFIG_USB_G_PRINTER is not set
-CONFIG_MMC=m
+CONFIG_USB_CDC_COMPOSITE=m
+CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set
 # CONFIG_MMC_UNSAFE_RESUME is not set
 
 #
 # MMC/SD Card Drivers
 #
-CONFIG_MMC_BLOCK=m
-# CONFIG_MMC_BLOCK_BOUNCE is not set
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
 # CONFIG_SDIO_UART is not set
-# CONFIG_MMC_TEST is not set
+CONFIG_MMC_TEST=m
 
 #
 # MMC/SD Host Controller Drivers
 #
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_ATMELMCI=y
 CONFIG_MMC_SPI=m
 # CONFIG_MEMSTICK is not set
 CONFIG_NEW_LEDS=y
@@ -802,7 +803,9 @@ CONFIG_LEDS_CLASS=y
 # LED drivers
 #
 CONFIG_LEDS_ATMEL_PWM=m
+# CONFIG_LEDS_PCA9532 is not set
 CONFIG_LEDS_GPIO=y
+# CONFIG_LEDS_PCA955X is not set
 
 #
 # LED Triggers
@@ -841,10 +844,13 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_PCF8583 is not set
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
 
 #
 # SPI RTC drivers
 #
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
 # CONFIG_RTC_DRV_MAX6902 is not set
 # CONFIG_RTC_DRV_R9701 is not set
 # CONFIG_RTC_DRV_RS5C348 is not set
@@ -864,8 +870,20 @@ CONFIG_RTC_INTF_DEV=y
 # on-CPU RTC drivers
 #
 CONFIG_RTC_DRV_AT32AP700X=y
-CONFIG_UIO=m
-# CONFIG_UIO_SMX is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+CONFIG_DW_DMAC=y
+CONFIG_DMA_ENGINE=y
+
+#
+# DMA Clients
+#
+# CONFIG_NET_DMA is not set
+CONFIG_DMATEST=m
+# CONFIG_UIO is not set
 
 #
 # File systems
@@ -943,6 +961,7 @@ CONFIG_JFFS2_RTIME=y
 # CONFIG_CRAMFS is not set
 # CONFIG_VXFS_FS is not set
 # CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
 # CONFIG_HPFS_FS is not set
 # CONFIG_QNX4FS_FS is not set
 # CONFIG_ROMFS_FS is not set
@@ -1011,6 +1030,8 @@ CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_DEBUG_SHIRQ is not set
 CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
 CONFIG_SCHED_DEBUG=y
 # CONFIG_SCHEDSTATS is not set
 # CONFIG_TIMER_STATS is not set
@@ -1029,6 +1050,7 @@ CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_DEBUG_VM is not set
 # CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 CONFIG_FRAME_POINTER=y
@@ -1056,6 +1078,7 @@ CONFIG_BITREVERSE=y
 # CONFIG_GENERIC_FIND_NEXT_BIT is not set
 CONFIG_CRC_CCITT=m
 # CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=m
 CONFIG_CRC_ITU_T=m
 CONFIG_CRC32=y
 CONFIG_CRC7=m
@@ -1063,6 +1086,7 @@ CONFIG_CRC7=m
 CONFIG_AUDIT_GENERIC=y
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_GENERIC_ALLOCATOR=y
 CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y

arch/avr32/configs/atstk1004_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc3
-# Mon May 26 13:34:57 2008
+# Linux kernel version: 2.6.27-rc1
+# Tue Aug  5 15:38:56 2008
 #
 CONFIG_AVR32=y
 CONFIG_GENERIC_GPIO=y
@@ -69,10 +69,16 @@ CONFIG_SLOB=y
 # CONFIG_PROFILING is not set
 # CONFIG_MARKERS is not set
 CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
 CONFIG_HAVE_KPROBES=y
 # CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
 # CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
 # CONFIG_PROC_PAGE_MONITOR is not set
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 # CONFIG_TINY_SHMEM is not set
 CONFIG_BASE_SMALL=1
 # CONFIG_MODULES is not set
@@ -97,6 +103,7 @@ CONFIG_BOARD_ATSTK1000=y
 # CONFIG_BOARD_ATSTK1002 is not set
 # CONFIG_BOARD_ATSTK1003 is not set
 CONFIG_BOARD_ATSTK1004=y
+# CONFIG_BOARD_ATSTK1006 is not set
 # CONFIG_BOARD_ATSTK100X_CUSTOM is not set
 # CONFIG_BOARD_ATSTK100X_SPI1 is not set
 # CONFIG_BOARD_ATSTK1000_J2_LED is not set
@@ -115,6 +122,7 @@ CONFIG_PHYS_OFFSET=0x10000000
 CONFIG_PREEMPT_NONE=y
 # CONFIG_PREEMPT_VOLUNTARY is not set
 # CONFIG_PREEMPT is not set
+CONFIG_QUICKLIST=y
 # CONFIG_HAVE_ARCH_BOOTMEM_NODE is not set
 # CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set
 # CONFIG_NEED_NODE_MEMMAP_SIZE is not set
@@ -133,6 +141,7 @@ CONFIG_PAGEFLAGS_EXTENDED=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_RESOURCES_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
 CONFIG_VIRT_TO_BUS=y
 # CONFIG_OWNERSHIP_TRACE is not set
 # CONFIG_NMI_DEBUGGING is not set
@@ -147,6 +156,8 @@ CONFIG_CMDLINE=""
 #
 # Power management options
 #
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
 
 #
 # CPU Frequency scaling
@@ -164,10 +175,6 @@ CONFIG_CMDLINE=""
 #
 CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
-
-#
-# Networking
-#
 CONFIG_NET=y
 
 #
@@ -390,24 +397,28 @@ CONFIG_SPI_ATMEL=y
 # CONFIG_SPI_AT25 is not set
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
-CONFIG_HAVE_GPIO_LIB=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_SYSFS is not set
 
 #
-# GPIO Support
+# I2C GPIO expanders:
 #
 
 #
-# I2C GPIO expanders:
+# PCI GPIO expanders:
 #
 
 #
 # SPI GPIO expanders:
 #
+# CONFIG_GPIO_MAX7301 is not set
 # CONFIG_GPIO_MCP23S08 is not set
 # CONFIG_W1 is not set
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
 # CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
 CONFIG_WATCHDOG=y
 # CONFIG_WATCHDOG_NOWAYOUT is not set
 
@@ -426,6 +437,7 @@ CONFIG_SSB_POSSIBLE=y
 #
 # Multifunction device drivers
 #
+# CONFIG_MFD_CORE is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
 
@@ -477,6 +489,9 @@ CONFIG_FB_ATMEL=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_LTV350QV=y
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
 # CONFIG_BACKLIGHT_CLASS_DEVICE is not set
 
 #
@@ -484,10 +499,6 @@ CONFIG_LCD_LTV350QV=y
 #
 # CONFIG_DISPLAY_SUPPORT is not set
 # CONFIG_LOGO is not set
-
-#
-# Sound
-#
 # CONFIG_SOUND is not set
 CONFIG_USB_SUPPORT=y
 # CONFIG_USB_ARCH_HAS_HCD is not set
@@ -507,7 +518,7 @@ CONFIG_USB_GADGET_ATMEL_USBA=y
 CONFIG_USB_ATMEL_USBA=y
 # CONFIG_USB_GADGET_FSL_USB2 is not set
 # CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_PXA25X is not set
 # CONFIG_USB_GADGET_M66592 is not set
 # CONFIG_USB_GADGET_PXA27X is not set
 # CONFIG_USB_GADGET_GOKU is not set
@@ -525,6 +536,7 @@ CONFIG_USB_ETH=y
 # CONFIG_USB_G_SERIAL is not set
 # CONFIG_USB_MIDI_GADGET is not set
 # CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
 # CONFIG_MMC is not set
 # CONFIG_MEMSTICK is not set
 # CONFIG_NEW_LEDS is not set
@@ -547,6 +559,8 @@ CONFIG_RTC_INTF_DEV=y
 #
 # SPI RTC drivers
 #
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
 # CONFIG_RTC_DRV_MAX6902 is not set
 # CONFIG_RTC_DRV_R9701 is not set
 # CONFIG_RTC_DRV_RS5C348 is not set
@@ -566,6 +580,7 @@ CONFIG_RTC_INTF_DEV=y
 # on-CPU RTC drivers
 #
 CONFIG_RTC_DRV_AT32AP700X=y
+# CONFIG_DMADEVICES is not set
 # CONFIG_UIO is not set
 
 #
@@ -620,6 +635,7 @@ CONFIG_MAGIC_SYSRQ=y
 # CONFIG_HEADERS_CHECK is not set
 # CONFIG_DEBUG_KERNEL is not set
 # CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
 # CONFIG_SAMPLES is not set
 
 #
@@ -638,12 +654,14 @@ CONFIG_BITREVERSE=y
 # CONFIG_GENERIC_FIND_NEXT_BIT is not set
 # CONFIG_CRC_CCITT is not set
 # CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
 # CONFIG_CRC7 is not set
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_GENERIC_ALLOCATOR=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y

arch/avr32/mach-at32ap/Makefile

 obj-y				+= pdc.o clock.o intc.o extint.o pio.o hsmc.o
+obj-y				+= hmatrix.o
 obj-$(CONFIG_CPU_AT32AP700X)	+= at32ap700x.o pm-at32ap700x.o
 obj-$(CONFIG_CPU_FREQ_AT32AP)	+= cpufreq.o
 obj-$(CONFIG_PM)		+= pm.o

arch/avr32/mach-at32ap/at32ap700x.c

@@ -22,13 +22,13 @@
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>
+#include <mach/hmatrix.h>
 #include <mach/portmux.h>
 #include <mach/sram.h>
 
 #include <video/atmel_lcdc.h>
 
 #include "clock.h"
-#include "hmatrix.h"
 #include "pio.h"
 #include "pm.h"
 
@@ -725,7 +725,7 @@ static struct clk pico_clk = {
  * HMATRIX
  * -------------------------------------------------------------------- */
 
-static struct clk hmatrix_clk = {
+struct clk at32_hmatrix_clk = {
 	.name		= "hmatrix_clk",
 	.parent		= &pbb_clk,
 	.mode		= pbb_clk_mode,
@@ -733,12 +733,6 @@ static struct clk hmatrix_clk = {
 	.index		= 2,
 	.users		= 1,
 };
-#define HMATRIX_BASE	((void __iomem *)0xfff00800)
-
-#define hmatrix_readl(reg)					\
-	__raw_readl((HMATRIX_BASE) + HMATRIX_##reg)
-#define hmatrix_writel(reg,value)				\
-	__raw_writel((value), (HMATRIX_BASE) + HMATRIX_##reg)
 
 /*
  * Set bits in the HMATRIX Special Function Register (SFR) used by the
@@ -748,13 +742,7 @@ static struct clk hmatrix_clk = {
  */
 static inline void set_ebi_sfr_bits(u32 mask)
 {
-	u32 sfr;
-
-	clk_enable(&hmatrix_clk);
-	sfr = hmatrix_readl(SFR4);
-	sfr |= mask;
-	hmatrix_writel(SFR4, sfr);
-	clk_disable(&hmatrix_clk);
+	hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, mask);
 }
 
 /* --------------------------------------------------------------------
@@ -1779,7 +1767,7 @@ static int __init at32_init_ide_or_cf(struct platform_device *pdev,
 			return ret;
 
 		select_peripheral(PE(21), PERIPH_A, 0); /* NCS4   -> OE_N  */
-		set_ebi_sfr_bits(HMATRIX_BIT(CS4A));
+		hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF0_ENABLE);
 		break;
 	case 5:
 		ret = platform_device_add_resources(pdev,
@@ -1789,7 +1777,7 @@ static int __init at32_init_ide_or_cf(struct platform_device *pdev,
 			return ret;
 
 		select_peripheral(PE(22), PERIPH_A, 0); /* NCS5   -> OE_N  */
-		set_ebi_sfr_bits(HMATRIX_BIT(CS5A));
+		hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF1_ENABLE);
 		break;
 	default:
 		return -EINVAL;
@@ -1905,7 +1893,7 @@ at32_add_device_nand(unsigned int id, struct atmel_nand_data *data)
 				sizeof(struct atmel_nand_data)))
 		goto fail;
 
-	set_ebi_sfr_bits(HMATRIX_BIT(CS3A));
+	hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_NAND_ENABLE);
 	if (data->enable_pin)
 		at32_select_gpio(data->enable_pin,
 				AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
@@ -2097,7 +2085,7 @@ struct clk *at32_clock_list[] = {
 	&pbb_clk,
 	&at32_pm_pclk,
 	&at32_intc0_pclk,
-	&hmatrix_clk,
+	&at32_hmatrix_clk,
 	&ebi_clk,
 	&hramc_clk,
 	&sdramc_clk,

arch/avr32/mach-at32ap/clock.c

@@ -16,6 +16,8 @@
 #include <linux/device.h>
 #include <linux/string.h>
 
+#include <mach/chip.h>
+
 #include "clock.h"
 
 static DEFINE_SPINLOCK(clk_lock);

arch/avr32/mach-at32ap/hmatrix.c

+/*
+ * High-Speed Bus Matrix helper functions
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <mach/chip.h>
+#include <mach/hmatrix.h>
+
+static inline void __hmatrix_write_reg(unsigned long offset, u32 value)
+{
+	__raw_writel(value, (void __iomem __force *)(HMATRIX_BASE + offset));
+}
+
+static inline u32 __hmatrix_read_reg(unsigned long offset)
+{
+	return __raw_readl((void __iomem __force *)(HMATRIX_BASE + offset));
+}
+
+/**
+ * hmatrix_write_reg - write HMATRIX configuration register
+ * @offset: register offset
+ * @value: value to be written to the register at @offset
+ */
+void hmatrix_write_reg(unsigned long offset, u32 value)
+{
+	clk_enable(&at32_hmatrix_clk);
+	__hmatrix_write_reg(offset, value);
+	__hmatrix_read_reg(offset);
+	clk_disable(&at32_hmatrix_clk);
+}
+
+/**
+ * hmatrix_read_reg - read HMATRIX configuration register
+ * @offset: register offset
+ *
+ * Returns the value of the register at @offset.
+ */
+u32 hmatrix_read_reg(unsigned long offset)
+{
+	u32 value;
+
+	clk_enable(&at32_hmatrix_clk);
+	value = __hmatrix_read_reg(offset);
+	clk_disable(&at32_hmatrix_clk);
+
+	return value;
+}
+
+/**
+ * hmatrix_sfr_set_bits - set bits in a slave's Special Function Register
+ * @slave_id: operate on the SFR belonging to this slave
+ * @mask: mask of bits to be set in the SFR
+ */
+void hmatrix_sfr_set_bits(unsigned int slave_id, u32 mask)
+{
+	u32 value;
+
+	clk_enable(&at32_hmatrix_clk);
+	value = __hmatrix_read_reg(HMATRIX_SFR(slave_id));
+	value |= mask;
+	__hmatrix_write_reg(HMATRIX_SFR(slave_id), value);
+	__hmatrix_read_reg(HMATRIX_SFR(slave_id));
+	clk_disable(&at32_hmatrix_clk);
+}
+
+/**
+ * hmatrix_sfr_set_bits - clear bits in a slave's Special Function Register
+ * @slave_id: operate on the SFR belonging to this slave
+ * @mask: mask of bits to be cleared in the SFR
+ */
+void hmatrix_sfr_clear_bits(unsigned int slave_id, u32 mask)
+{
+	u32 value;
+
+	clk_enable(&at32_hmatrix_clk);
+	value = __hmatrix_read_reg(HMATRIX_SFR(slave_id));
+	value &= ~mask;
+	__hmatrix_write_reg(HMATRIX_SFR(slave_id), value);
+	__hmatrix_read_reg(HMATRIX_SFR(slave_id));
+	clk_disable(&at32_hmatrix_clk);
+}

arch/avr32/mach-at32ap/hmatrix.h

-/*
- * Register definitions for High-Speed Bus Matrix
- */
-#ifndef __HMATRIX_H
-#define __HMATRIX_H
-
-/* HMATRIX register offsets */
-#define HMATRIX_MCFG0				0x0000
-#define HMATRIX_MCFG1				0x0004
-#define HMATRIX_MCFG2				0x0008
-#define HMATRIX_MCFG3				0x000c
-#define HMATRIX_MCFG4				0x0010
-#define HMATRIX_MCFG5				0x0014
-#define HMATRIX_MCFG6				0x0018
-#define HMATRIX_MCFG7				0x001c
-#define HMATRIX_MCFG8				0x0020
-#define HMATRIX_MCFG9				0x0024
-#define HMATRIX_MCFG10				0x0028
-#define HMATRIX_MCFG11				0x002c
-#define HMATRIX_MCFG12				0x0030
-#define HMATRIX_MCFG13				0x0034
-#define HMATRIX_MCFG14				0x0038
-#define HMATRIX_MCFG15				0x003c
-#define HMATRIX_SCFG0				0x0040
-#define HMATRIX_SCFG1				0x0044
-#define HMATRIX_SCFG2				0x0048
-#define HMATRIX_SCFG3				0x004c
-#define HMATRIX_SCFG4				0x0050
-#define HMATRIX_SCFG5				0x0054
-#define HMATRIX_SCFG6				0x0058
-#define HMATRIX_SCFG7				0x005c
-#define HMATRIX_SCFG8				0x0060
-#define HMATRIX_SCFG9				0x0064
-#define HMATRIX_SCFG10				0x0068
-#define HMATRIX_SCFG11				0x006c
-#define HMATRIX_SCFG12				0x0070
-#define HMATRIX_SCFG13				0x0074
-#define HMATRIX_SCFG14				0x0078
-#define HMATRIX_SCFG15				0x007c
-#define HMATRIX_PRAS0				0x0080
-#define HMATRIX_PRBS0				0x0084
-#define HMATRIX_PRAS1				0x0088
-#define HMATRIX_PRBS1				0x008c
-#define HMATRIX_PRAS2				0x0090
-#define HMATRIX_PRBS2				0x0094
-#define HMATRIX_PRAS3				0x0098
-#define HMATRIX_PRBS3				0x009c
-#define HMATRIX_PRAS4				0x00a0
-#define HMATRIX_PRBS4				0x00a4
-#define HMATRIX_PRAS5				0x00a8
-#define HMATRIX_PRBS5				0x00ac
-#define HMATRIX_PRAS6				0x00b0
-#define HMATRIX_PRBS6				0x00b4
-#define HMATRIX_PRAS7				0x00b8
-#define HMATRIX_PRBS7				0x00bc
-#define HMATRIX_PRAS8				0x00c0
-#define HMATRIX_PRBS8				0x00c4
-#define HMATRIX_PRAS9				0x00c8
-#define HMATRIX_PRBS9				0x00cc
-#define HMATRIX_PRAS10				0x00d0
-#define HMATRIX_PRBS10				0x00d4
-#define HMATRIX_PRAS11				0x00d8
-#define HMATRIX_PRBS11				0x00dc
-#define HMATRIX_PRAS12				0x00e0
-#define HMATRIX_PRBS12				0x00e4
-#define HMATRIX_PRAS13				0x00e8
-#define HMATRIX_PRBS13				0x00ec
-#define HMATRIX_PRAS14				0x00f0
-#define HMATRIX_PRBS14				0x00f4
-#define HMATRIX_PRAS15				0x00f8
-#define HMATRIX_PRBS15				0x00fc
-#define HMATRIX_MRCR				0x0100
-#define HMATRIX_SFR0				0x0110
-#define HMATRIX_SFR1				0x0114
-#define HMATRIX_SFR2				0x0118
-#define HMATRIX_SFR3				0x011c
-#define HMATRIX_SFR4				0x0120
-#define HMATRIX_SFR5				0x0124
-#define HMATRIX_SFR6				0x0128
-#define HMATRIX_SFR7				0x012c
-#define HMATRIX_SFR8				0x0130
-#define HMATRIX_SFR9				0x0134
-#define HMATRIX_SFR10				0x0138
-#define HMATRIX_SFR11				0x013c
-#define HMATRIX_SFR12				0x0140
-#define HMATRIX_SFR13				0x0144
-#define HMATRIX_SFR14				0x0148
-#define HMATRIX_SFR15				0x014c
-
-/* Bitfields in MCFGx */
-#define HMATRIX_ULBT_OFFSET			0
-#define HMATRIX_ULBT_SIZE			3
-
-/* Bitfields in SCFGx */
-#define HMATRIX_SLOT_CYCLE_OFFSET		0
-#define HMATRIX_SLOT_CYCLE_SIZE			8
-#define HMATRIX_DEFMSTR_TYPE_OFFSET		16
-#define HMATRIX_DEFMSTR_TYPE_SIZE		2
-#define HMATRIX_FIXED_DEFMSTR_OFFSET		18
-#define HMATRIX_FIXED_DEFMSTR_SIZE		4
-#define HMATRIX_ARBT_OFFSET			24
-#define HMATRIX_ARBT_SIZE			2
-
-/* Bitfields in PRASx */
-#define HMATRIX_M0PR_OFFSET			0
-#define HMATRIX_M0PR_SIZE			4
-#define HMATRIX_M1PR_OFFSET			4
-#define HMATRIX_M1PR_SIZE			4
-#define HMATRIX_M2PR_OFFSET			8
-#define HMATRIX_M2PR_SIZE			4
-#define HMATRIX_M3PR_OFFSET			12
-#define HMATRIX_M3PR_SIZE			4
-#define HMATRIX_M4PR_OFFSET			16
-#define HMATRIX_M4PR_SIZE			4
-#define HMATRIX_M5PR_OFFSET			20
-#define HMATRIX_M5PR_SIZE			4
-#define HMATRIX_M6PR_OFFSET			24
-#define HMATRIX_M6PR_SIZE			4
-#define HMATRIX_M7PR_OFFSET			28
-#define HMATRIX_M7PR_SIZE			4
-
-/* Bitfields in PRBSx */
-#define HMATRIX_M8PR_OFFSET			0
-#define HMATRIX_M8PR_SIZE			4
-#define HMATRIX_M9PR_OFFSET			4
-#define HMATRIX_M9PR_SIZE			4
-#define HMATRIX_M10PR_OFFSET			8
-#define HMATRIX_M10PR_SIZE			4
-#define HMATRIX_M11PR_OFFSET			12
-#define HMATRIX_M11PR_SIZE			4
-#define HMATRIX_M12PR_OFFSET			16
-#define HMATRIX_M12PR_SIZE			4
-#define HMATRIX_M13PR_OFFSET			20
-#define HMATRIX_M13PR_SIZE			4
-#define HMATRIX_M14PR_OFFSET			24
-#define HMATRIX_M14PR_SIZE			4
-#define HMATRIX_M15PR_OFFSET			28
-#define HMATRIX_M15PR_SIZE			4
-
-/* Bitfields in SFR4 */
-#define HMATRIX_CS1A_OFFSET			1
-#define HMATRIX_CS1A_SIZE			1
-#define HMATRIX_CS3A_OFFSET			3
-#define HMATRIX_CS3A_SIZE			1
-#define HMATRIX_CS4A_OFFSET			4
-#define HMATRIX_CS4A_SIZE			1
-#define HMATRIX_CS5A_OFFSET			5
-#define HMATRIX_CS5A_SIZE			1
-#define HMATRIX_DBPUC_OFFSET			8
-#define HMATRIX_DBPUC_SIZE			1
-
-/* Constants for ULBT */
-#define HMATRIX_ULBT_INFINITE			0
-#define HMATRIX_ULBT_SINGLE			1
-#define HMATRIX_ULBT_FOUR_BEAT			2
-#define HMATRIX_ULBT_EIGHT_BEAT			3
-#define HMATRIX_ULBT_SIXTEEN_BEAT		4
-
-/* Constants for DEFMSTR_TYPE */
-#define HMATRIX_DEFMSTR_TYPE_NO_DEFAULT		0
-#define HMATRIX_DEFMSTR_TYPE_LAST_DEFAULT	1
-#define HMATRIX_DEFMSTR_TYPE_FIXED_DEFAULT	2
-
-/* Constants for ARBT */
-#define HMATRIX_ARBT_ROUND_ROBIN		0
-#define HMATRIX_ARBT_FIXED_PRIORITY		1
-
-/* Bit manipulation macros */
-#define HMATRIX_BIT(name)					\
-	(1 << HMATRIX_##name##_OFFSET)
-#define HMATRIX_BF(name,value)					\
-	(((value) & ((1 << HMATRIX_##name##_SIZE) - 1))		\
-	 << HMATRIX_##name##_OFFSET)
-#define HMATRIX_BFEXT(name,value)				\
-	(((value) >> HMATRIX_##name##_OFFSET)			\
-	 & ((1 << HMATRIX_##name##_SIZE) - 1))
-#define HMATRIX_BFINS(name,value,old)				\
-	(((old) & ~(((1 << HMATRIX_##name##_SIZE) - 1)		\
-		    << HMATRIX_##name##_OFFSET))		\
-	 | HMATRIX_BF(name,value))
-
-#endif /* __HMATRIX_H */

arch/avr32/mach-at32ap/include/mach/at32ap700x.h

@@ -46,4 +46,41 @@
 #define DMAC_DMAREQ_2		9
 #define DMAC_DMAREQ_3		10
 
+/* HSB master IDs */
+#define HMATRIX_MASTER_CPU_DCACHE		0
+#define HMATRIX_MASTER_CPU_ICACHE		1
+#define HMATRIX_MASTER_PDC			2
+#define HMATRIX_MASTER_ISI			3
+#define HMATRIX_MASTER_USBA			4
+#define HMATRIX_MASTER_LCDC			5
+#define HMATRIX_MASTER_MACB0			6
+#define HMATRIX_MASTER_MACB1			7
+#define HMATRIX_MASTER_DMACA_M0			8
+#define HMATRIX_MASTER_DMACA_M1			9
+
+/* HSB slave IDs */
+#define HMATRIX_SLAVE_SRAM0			0
+#define HMATRIX_SLAVE_SRAM1			1
+#define HMATRIX_SLAVE_PBA			2
+#define HMATRIX_SLAVE_PBB			3
+#define HMATRIX_SLAVE_EBI			4
+#define HMATRIX_SLAVE_USBA			5
+#define HMATRIX_SLAVE_LCDC			6
+#define HMATRIX_SLAVE_DMACA			7
+
+/* Bits in HMATRIX SFR4 (EBI) */
+#define HMATRIX_EBI_SDRAM_ENABLE		(1 << 1)
+#define HMATRIX_EBI_NAND_ENABLE			(1 << 3)
+#define HMATRIX_EBI_CF0_ENABLE			(1 << 4)
+#define HMATRIX_EBI_CF1_ENABLE			(1 << 5)
+#define HMATRIX_EBI_PULLUP_DISABLE		(1 << 8)
+
+/*
+ * Base addresses of controllers that may be accessed early by
+ * platform code.
+ */
+#define PM_BASE		0xfff00000
+#define HMATRIX_BASE	0xfff00800
+#define SDRAMC_BASE	0xfff03800
+
 #endif /* __ASM_ARCH_AT32AP700X_H__ */

include/asm-avr32/arch-at32ap/init.h → arch/avr32/mach-at32ap/include/mach/chip.h

 /*
- * AT32AP platform initialization calls.
+ * AVR32 chip-specific definitions
  *
- * Copyright (C) 2006 Atmel Corporation
+ * Copyright (C) 2008 Atmel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-#ifndef __ASM_AVR32_AT32AP_INIT_H__
-#define __ASM_AVR32_AT32AP_INIT_H__
+#ifndef __ASM_AVR32_ARCH_CHIP_H__
+#define __ASM_AVR32_ARCH_CHIP_H__
 
-void setup_platform(void);
-void setup_board(void);
+#if defined(CONFIG_CPU_AT32AP700X)
+# include <mach/at32ap700x.h>
+#else
+# error Unknown chip type selected
+#endif
 
-void at32_setup_serial_console(unsigned int usart_id);
-
-#endif /* __ASM_AVR32_AT32AP_INIT_H__ */
+#endif /* __ASM_AVR32_ARCH_CHIP_H__ */

arch/avr32/mach-at32ap/include/mach/hmatrix.h

+/*
+ * High-Speed Bus Matrix configuration registers
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __HMATRIX_H
+#define __HMATRIX_H
+
+extern struct clk at32_hmatrix_clk;
+
+void hmatrix_write_reg(unsigned long offset, u32 value);
+u32 hmatrix_read_reg(unsigned long offset);
+
+void hmatrix_sfr_set_bits(unsigned int slave_id, u32 mask);
+void hmatrix_sfr_clear_bits(unsigned int slave_id, u32 mask);
+
+/* Master Configuration register */
+#define HMATRIX_MCFG(m)			(0x0000 + 4 * (m))
+/* Undefined length burst limit */
+# define HMATRIX_MCFG_ULBT_INFINITE	0	/* Infinite length */
+# define HMATRIX_MCFG_ULBT_SINGLE	1	/* Single Access */
+# define HMATRIX_MCFG_ULBT_FOUR_BEAT	2	/* Four beat */
+# define HMATRIX_MCFG_ULBT_EIGHT_BEAT	3	/* Eight beat */
+# define HMATRIX_MCFG_ULBT_SIXTEEN_BEAT	4	/* Sixteen beat */
+
+/* Slave Configuration register */
+#define HMATRIX_SCFG(s)			(0x0040 + 4 * (s))
+# define HMATRIX_SCFG_SLOT_CYCLE(x)	((x) <<  0)	/* Max burst cycles */
+# define HMATRIX_SCFG_DEFMSTR_NONE	(  0 << 16)	/* No default master */
+# define HMATRIX_SCFG_DEFMSTR_LAST	(  1 << 16)	/* Last def master */
+# define HMATRIX_SCFG_DEFMSTR_FIXED	(  2 << 16)	/* Fixed def master */
+# define HMATRIX_SCFG_FIXED_DEFMSTR(m)	((m) << 18)	/* Fixed master ID */
+# define HMATRIX_SCFG_ARBT_ROUND_ROBIN	(  0 << 24)	/* RR arbitration */
+# define HMATRIX_SCFG_ARBT_FIXED_PRIO	(  1 << 24)	/* Fixed priority */
+
+/* Slave Priority register A (master 0..7) */
+#define HMATRIX_PRAS(s)			(0x0080 + 8 * (s))
+# define HMATRIX_PRAS_PRIO(m, p)	((p) << ((m) * 4))
+
+/* Slave Priority register A (master 8..15) */
+#define HMATRIX_PRBS(s)			(0x0084 + 8 * (s))
+# define HMATRIX_PRBS_PRIO(m, p)	((p) << (((m) - 8) * 4))
+
+/* Master Remap Control Register */
+#define HMATRIX_MRCR				0x0100
+# define HMATRIX_MRCR_REMAP(m)		(  1 << (m))	/* Remap master m */
+
+/* Special Function Register. Bit definitions are chip-specific */
+#define HMATRIX_SFR(s)			(0x0110 + 4 * (s))
+
+#endif /* __HMATRIX_H */

arch/avr32/mach-at32ap/pm.c

@@ -14,12 +14,10 @@
 #include <asm/cacheflush.h>
 #include <asm/sysreg.h>
 
+#include <mach/chip.h>
 #include <mach/pm.h>
 #include <mach/sram.h>
 
-/* FIXME: This is only valid for AP7000 */
-#define SDRAMC_BASE	0xfff03800
-
 #include "sdramc.h"
 
 #define SRAM_PAGE_FLAGS	(SYSREG_BIT(TLBELO_D) | SYSREG_BF(SZ, 1)	\

arch/avr32/mach-at32ap/pm.h

@@ -4,14 +4,6 @@
 #ifndef __ARCH_AVR32_MACH_AT32AP_PM_H__
 #define __ARCH_AVR32_MACH_AT32AP_PM_H__
 
-/*
- * We can reduce the code size a bit by using a constant here. Since
- * this file is only used on AVR32 AP CPUs with segmentation enabled,
- * it's safe to not use ioremap. Generic drivers should of course
- * never do this.
- */
-#define AT32_PM_BASE	0xfff00000
-
 /* PM register offsets */
 #define PM_MCCTRL				0x0000
 #define PM_CKSEL				0x0004
@@ -113,8 +105,8 @@
 
 /* Register access macros */
 #define pm_readl(reg)							\
-	__raw_readl((void __iomem __force *)AT32_PM_BASE + PM_##reg)
+	__raw_readl((void __iomem __force *)PM_BASE + PM_##reg)
 #define pm_writel(reg,value)						\
-	__raw_writel((value), (void __iomem __force *)AT32_PM_BASE + PM_##reg)
+	__raw_writel((value), (void __iomem __force *)PM_BASE + PM_##reg)
 
 #endif /* __ARCH_AVR32_MACH_AT32AP_PM_H__ */

include/asm-avr32/arch-at32ap/at32ap700x.h

-/*
- * Pin definitions for AT32AP7000.
- *
- * Copyright (C) 2006 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_ARCH_AT32AP700X_H__
-#define __ASM_ARCH_AT32AP700X_H__
-
-#define GPIO_PERIPH_A	0
-#define GPIO_PERIPH_B	1
-
-/*
- * Pin numbers identifying specific GPIO pins on the chip. They can
- * also be converted to IRQ numbers by passing them through
- * gpio_to_irq().
- */
-#define GPIO_PIOA_BASE	(0)
-#define GPIO_PIOB_BASE	(GPIO_PIOA_BASE + 32)
-#define GPIO_PIOC_BASE	(GPIO_PIOB_BASE + 32)
-#define GPIO_PIOD_BASE	(GPIO_PIOC_BASE + 32)
-#define GPIO_PIOE_BASE	(GPIO_PIOD_BASE + 32)
-
-#define GPIO_PIN_PA(N)	(GPIO_PIOA_BASE + (N))
-#define GPIO_PIN_PB(N)	(GPIO_PIOB_BASE + (N))
-#define GPIO_PIN_PC(N)	(GPIO_PIOC_BASE + (N))
-#define GPIO_PIN_PD(N)	(GPIO_PIOD_BASE + (N))
-#define GPIO_PIN_PE(N)	(GPIO_PIOE_BASE + (N))
-
-
-/*
- * DMAC peripheral hardware handshaking interfaces, used with dw_dmac
- */
-#define DMAC_MCI_RX		0
-#define DMAC_MCI_TX		1
-#define DMAC_DAC_TX		2
-#define DMAC_AC97_A_RX		3
-#define DMAC_AC97_A_TX		4
-#define DMAC_AC97_B_RX		5
-#define DMAC_AC97_B_TX		6
-#define DMAC_DMAREQ_0		7
-#define DMAC_DMAREQ_1		8
-#define DMAC_DMAREQ_2		9
-#define DMAC_DMAREQ_3		10
-
-#endif /* __ASM_ARCH_AT32AP700X_H__ */

include/asm-avr32/arch-at32ap/board.h

-/*
- * Platform data definitions.
- */
-#ifndef __ASM_ARCH_BOARD_H
-#define __ASM_ARCH_BOARD_H
-
-#include <linux/types.h>
-
-#define GPIO_PIN_NONE	(-1)
-
-/*
- * Clock rates for various on-board oscillators. The number of entries
- * in this array is chip-dependent.
- */
-extern unsigned long at32_board_osc_rates[];
-  
-/* Add basic devices: system manager, interrupt controller, portmuxes, etc. */
-void at32_add_system_devices(void);
-
-#define ATMEL_MAX_UART	4
-extern struct platform_device *atmel_default_console_device;
-
-struct atmel_uart_data {
-	short		use_dma_tx;	/* use transmit DMA? */
-	short		use_dma_rx;	/* use receive DMA? */
-	void __iomem	*regs;		/* virtual base address, if any */
-};
-void at32_map_usart(unsigned int hw_id, unsigned int line);
-struct platform_device *at32_add_device_usart(unsigned int id);
-
-struct eth_platform_data {
-	u32	phy_mask;
-	u8	is_rmii;
-};
-struct platform_device *
-at32_add_device_eth(unsigned int id, struct eth_platform_data *data);
-
-struct spi_board_info;
-struct platform_device *
-at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
-
-struct atmel_lcdfb_info;
-struct platform_device *
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
-		     unsigned long fbmem_start, unsigned long fbmem_len,
-		     unsigned int pin_config);
-
-struct usba_platform_data;
-struct platform_device *
-at32_add_device_usba(unsigned int id, struct usba_platform_data *data);
-
-struct ide_platform_data {
-	u8      cs;
-};
-struct platform_device *
-at32_add_device_ide(unsigned int id, unsigned int extint,
-		    struct ide_platform_data *data);
-
-/* mask says which PWM channels to mux */
-struct platform_device *at32_add_device_pwm(u32 mask);
-
-/* depending on what's hooked up, not all SSC pins will be used */
-#define	ATMEL_SSC_TK		0x01
-#define	ATMEL_SSC_TF		0x02
-#define	ATMEL_SSC_TD		0x04
-#define	ATMEL_SSC_TX		(ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
-
-#define	ATMEL_SSC_RK		0x10
-#define	ATMEL_SSC_RF		0x20
-#define	ATMEL_SSC_RD		0x40
-#define	ATMEL_SSC_RX		(ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
-
-struct platform_device *
-at32_add_device_ssc(unsigned int id, unsigned int flags);
-
-struct i2c_board_info;
-struct platform_device *at32_add_device_twi(unsigned int id,
-					    struct i2c_board_info *b,
-					    unsigned int n);
-
-struct mci_platform_data;
-struct platform_device *
-at32_add_device_mci(unsigned int id, struct mci_platform_data *data);
-
-struct ac97c_platform_data {
-	unsigned short dma_rx_periph_id;
-	unsigned short dma_tx_periph_id;
-	unsigned short dma_controller_id;
-	int reset_pin;
-};
-struct platform_device *
-at32_add_device_ac97c(unsigned int id, struct ac97c_platform_data *data);
-
-struct platform_device *at32_add_device_abdac(unsigned int id);
-struct platform_device *at32_add_device_psif(unsigned int id);
-
-struct cf_platform_data {
-	int	detect_pin;
-	int	reset_pin;
-	int	vcc_pin;
-	int	ready_pin;
-	u8	cs;
-};
-struct platform_device *
-at32_add_device_cf(unsigned int id, unsigned int extint,
-		struct cf_platform_data *data);
-
-/* NAND / SmartMedia */
-struct atmel_nand_data {
-	int	enable_pin;	/* chip enable */
-	int	det_pin;	/* card detect */
-	int	rdy_pin;	/* ready/busy */
-	u8	ale;		/* address line number connected to ALE */
-	u8	cle;		/* address line number connected to CLE */
-	u8	bus_width_16;	/* buswidth is 16 bit */
-	struct mtd_partition *(*partition_info)(int size, int *num_partitions);
-};
-struct platform_device *
-at32_add_device_nand(unsigned int id, struct atmel_nand_data *data);
-
-#endif /* __ASM_ARCH_BOARD_H */

include/asm-avr32/arch-at32ap/cpu.h

-/*
- * AVR32 and (fake) AT91 CPU identification
- *
- * Copyright (C) 2007 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_ARCH_CPU_H
-#define __ASM_ARCH_CPU_H
-
-/*
- * Only AT32AP7000 is defined for now. We can identify the specific
- * chip at runtime, but I'm not sure if it's really worth it.
- */
-#ifdef CONFIG_CPU_AT32AP700X
-# define cpu_is_at32ap7000()	(1)
-#else
-# define cpu_is_at32ap7000()	(0)
-#endif
-
-/*
- * Since this is AVR32, we will never run on any AT91 CPU. But these
- * definitions may reduce clutter in common drivers.
- */
-#define cpu_is_at91rm9200()	(0)
-#define cpu_is_at91sam9xe()	(0)
-#define cpu_is_at91sam9260()	(0)
-#define cpu_is_at91sam9261()	(0)
-#define cpu_is_at91sam9263()	(0)
-#define cpu_is_at91sam9rl()	(0)
-#define cpu_is_at91cap9()	(0)
-
-#endif /* __ASM_ARCH_CPU_H */

include/asm-avr32/arch-at32ap/gpio.h

-#ifndef __ASM_AVR32_ARCH_GPIO_H
-#define __ASM_AVR32_ARCH_GPIO_H
-
-#include <linux/compiler.h>
-#include <asm/irq.h>
-
-
-/* Some GPIO chips can manage IRQs; some can't.  The exact numbers can
- * be changed if needed, but for the moment they're not configurable.
- */
-#define ARCH_NR_GPIOS	(NR_GPIO_IRQS + 2 * 32)
-
-
-/* Arch-neutral GPIO API, supporting both "native" and external GPIOs. */
-#include <asm-generic/gpio.h>
-
-static inline int gpio_get_value(unsigned int gpio)
-{
-	return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned int gpio, int value)
-{
-	__gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned int gpio)
-{
-	return __gpio_cansleep(gpio);
-}
-
-
-static inline int gpio_to_irq(unsigned int gpio)
-{
-	if (gpio < NR_GPIO_IRQS)
-		return gpio + GPIO_IRQ_BASE;
-	return -EINVAL;
-}
-
-static inline int irq_to_gpio(unsigned int irq)
-{
-	return irq - GPIO_IRQ_BASE;
-}
-
-#endif /* __ASM_AVR32_ARCH_GPIO_H */

include/asm-avr32/arch-at32ap/io.h

-#ifndef __ASM_AVR32_ARCH_AT32AP_IO_H
-#define __ASM_AVR32_ARCH_AT32AP_IO_H
-
-/* For "bizarre" halfword swapping */
-#include <linux/byteorder/swabb.h>
-
-#if defined(CONFIG_AP700X_32_BIT_SMC)
-# define __swizzle_addr_b(addr)	(addr ^ 3UL)
-# define __swizzle_addr_w(addr)	(addr ^ 2UL)
-# define __swizzle_addr_l(addr)	(addr)
-# define ioswabb(a, x)		(x)
-# define ioswabw(a, x)		(x)
-# define ioswabl(a, x)		(x)
-# define __mem_ioswabb(a, x)	(x)
-# define __mem_ioswabw(a, x)	swab16(x)
-# define __mem_ioswabl(a, x)	swab32(x)
-#elif defined(CONFIG_AP700X_16_BIT_SMC)
-# define __swizzle_addr_b(addr)	(addr ^ 1UL)
-# define __swizzle_addr_w(addr)	(addr)
-# define __swizzle_addr_l(addr)	(addr)
-# define ioswabb(a, x)		(x)
-# define ioswabw(a, x)		(x)
-# define ioswabl(a, x)		swahw32(x)
-# define __mem_ioswabb(a, x)	(x)
-# define __mem_ioswabw(a, x)	swab16(x)
-# define __mem_ioswabl(a, x)	swahb32(x)
-#else
-# define __swizzle_addr_b(addr)	(addr)
-# define __swizzle_addr_w(addr)	(addr)
-# define __swizzle_addr_l(addr)	(addr)
-# define ioswabb(a, x)		(x)
-# define ioswabw(a, x)		swab16(x)
-# define ioswabl(a, x)		swab32(x)
-# define __mem_ioswabb(a, x)	(x)
-# define __mem_ioswabw(a, x)	(x)
-# define __mem_ioswabl(a, x)	(x)
-#endif
-
-#endif /* __ASM_AVR32_ARCH_AT32AP_IO_H */

include/asm-avr32/arch-at32ap/irq.h

-#ifndef __ASM_AVR32_ARCH_IRQ_H
-#define __ASM_AVR32_ARCH_IRQ_H
-
-#define EIM_IRQ_BASE	NR_INTERNAL_IRQS
-#define NR_EIM_IRQS	32
-#define AT32_EXTINT(n)	(EIM_IRQ_BASE + (n))
-
-#define GPIO_IRQ_BASE	(EIM_IRQ_BASE + NR_EIM_IRQS)
-#define NR_GPIO_CTLR	(5 /*internal*/ + 1 /*external*/)
-#define NR_GPIO_IRQS	(NR_GPIO_CTLR * 32)
-
-#define NR_IRQS		(GPIO_IRQ_BASE + NR_GPIO_IRQS)
-
-#endif /* __ASM_AVR32_ARCH_IRQ_H */

include/asm-avr32/arch-at32ap/pm.h

-/*
- * AVR32 AP Power Management.
- *
- * Copyright (C) 2008 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_AVR32_ARCH_PM_H
-#define __ASM_AVR32_ARCH_PM_H
-
-/* Possible arguments to the "sleep" instruction */
-#define CPU_SLEEP_IDLE		0
-#define CPU_SLEEP_FROZEN	1
-#define CPU_SLEEP_STANDBY	2
-#define CPU_SLEEP_STOP		3
-#define CPU_SLEEP_STATIC	5
-
-#ifndef __ASSEMBLY__
-extern void cpu_enter_idle(void);
-extern void cpu_enter_standby(unsigned long sdramc_base);
-
-extern bool disable_idle_sleep;
-
-static inline void cpu_disable_idle_sleep(void)
-{
-	disable_idle_sleep = true;
-}
-
-static inline void cpu_enable_idle_sleep(void)
-{
-	disable_idle_sleep = false;
-}
-
-static inline void cpu_idle_sleep(void)
-{
-	/*
-	 * If we're using the COUNT and COMPARE registers for
-	 * timekeeping, we can't use the IDLE state.
-	 */
-	if (disable_idle_sleep)
-		cpu_relax();
-	else
-		cpu_enter_idle();
-}
-
-void intc_set_suspend_handler(unsigned long offset);
-#endif
-
-#endif /* __ASM_AVR32_ARCH_PM_H */

include/asm-avr32/arch-at32ap/portmux.h

-/*
- * AT32 portmux interface.
- *
- * Copyright (C) 2006 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_ARCH_PORTMUX_H__
-#define __ASM_ARCH_PORTMUX_H__
-
-/*
- * Set up pin multiplexing, called from board init only.
- *
- * The following flags determine the initial state of the pin.
- */
-#define AT32_GPIOF_PULLUP	0x00000001	/* (not-OUT) Enable pull-up */
-#define AT32_GPIOF_OUTPUT	0x00000002	/* (OUT) Enable output driver */
-#define AT32_GPIOF_HIGH		0x00000004	/* (OUT) Set output high */
-#define AT32_GPIOF_DEGLITCH	0x00000008	/* (IN) Filter glitches */
-#define AT32_GPIOF_MULTIDRV	0x00000010	/* Enable multidriver option */
-
-void at32_select_periph(unsigned int pin, unsigned int periph,
-			unsigned long flags);
-void at32_select_gpio(unsigned int pin, unsigned long flags);
-void at32_reserve_pin(unsigned int pin);
-
-#endif /* __ASM_ARCH_PORTMUX_H__ */

include/asm-avr32/arch-at32ap/smc.h

-/*
- * Static Memory Controller for AT32 chips
- *
- * Copyright (C) 2006 Atmel Corporation
- *
- * Inspired by the OMAP2 General-Purpose Memory Controller interface
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ARCH_AT32AP_SMC_H
-#define __ARCH_AT32AP_SMC_H
-
-/*
- * All timing parameters are in nanoseconds.
- */
-struct smc_timing {
-	/* Delay from address valid to assertion of given strobe */
-	int ncs_read_setup;
-	int nrd_setup;
-	int ncs_write_setup;
-	int nwe_setup;
-
-	/* Pulse length of given strobe */
-	int ncs_read_pulse;
-	int nrd_pulse;
-	int ncs_write_pulse;
-	int nwe_pulse;
-
-	/* Total cycle length of given operation */
-	int read_cycle;
-	int write_cycle;
-
-	/* Minimal recovery times, will extend cycle if needed */
-	int ncs_read_recover;
-	int nrd_recover;
-	int ncs_write_recover;
-	int nwe_recover;
-};
-
-/*
- * All timing parameters are in clock cycles.
- */
-struct smc_config {
-
-	/* Delay from address valid to assertion of given strobe */
-	u8		ncs_read_setup;
-	u8		nrd_setup;
-	u8		ncs_write_setup;
-	u8		nwe_setup;
-
-	/* Pulse length of given strobe */
-	u8		ncs_read_pulse;
-	u8		nrd_pulse;
-	u8		ncs_write_pulse;
-	u8		nwe_pulse;
-
-	/* Total cycle length of given operation */
-	u8		read_cycle;
-	u8		write_cycle;
-
-	/* Bus width in bytes */
-	u8		bus_width;
-
-	/*
-	 * 0: Data is sampled on rising edge of NCS
-	 * 1: Data is sampled on rising edge of NRD
-	 */
-	unsigned int	nrd_controlled:1;
-
-	/*
-	 * 0: Data is driven on falling edge of NCS
-	 * 1: Data is driven on falling edge of NWR
-	 */
-	unsigned int	nwe_controlled:1;
-
-	/*
-	 * 0: NWAIT is disabled
-	 * 1: Reserved
-	 * 2: NWAIT is frozen mode
-	 * 3: NWAIT in ready mode
-	 */
-	unsigned int	nwait_mode:2;
-
-	/*
-	 * 0: Byte select access type
-	 * 1: Byte write access type
-	 */
-	unsigned int	byte_write:1;
-
-	/*
-	 * Number of clock cycles before data is released after
-	 * the rising edge of the read controlling signal
-	 *
-	 * Total cycles from SMC is tdf_cycles + 1
-	 */
-	unsigned int	tdf_cycles:4;
-
-	/*
-	 * 0: TDF optimization disabled
-	 * 1: TDF optimization enabled
-	 */
-	unsigned int	tdf_mode:1;
-};
-
-extern void smc_set_timing(struct smc_config *config,
-			   const struct smc_timing *timing);
-
-extern int smc_set_configuration(int cs, const struct smc_config *config);
-extern struct smc_config *smc_get_configuration(int cs);
-
-#endif /* __ARCH_AT32AP_SMC_H */

include/asm-avr32/arch-at32ap/sram.h

-/*
- * Simple SRAM allocator
- *
- * Copyright (C) 2008 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_AVR32_ARCH_SRAM_H
-#define __ASM_AVR32_ARCH_SRAM_H
-
-#include <linux/genalloc.h>
-
-extern struct gen_pool *sram_pool;
-
-static inline unsigned long sram_alloc(size_t len)
-{
-	if (!sram_pool)
-		return 0UL;
-
-	return gen_pool_alloc(sram_pool, len);
-}
-
-static inline void sram_free(unsigned long addr, size_t len)
-{
-	return gen_pool_free(sram_pool, addr, len);
-}
-
-#endif /* __ASM_AVR32_ARCH_SRAM_H */